[ Upstream commit b34f4de6d3 ]
'qos_pfc' test checks PFC behavior. The idea is to limit the traffic
using a shaper somewhere in the flow of the packets. In this area, the
buffer is smaller than the buffer at the beginning of the flow, so it fills
up until there is no more space left. The test configures there PFC
which is supposed to notice that the headroom is filling up and send PFC
Xoff to indicate the transmitter to stop sending traffic for the priorities
sharing this PG.
The Xon/Xoff threshold is auto-configured and always equal to
2*(MTU rounded up to cell size). Even after sending the PFC Xoff packet,
traffic will keep arriving until the transmitter receives and processes
the PFC packet. This amount of traffic is known as the PFC delay allowance.
Currently the buffer for the delay traffic is configured as 100KB. The
MTU in the test is 10KB, therefore the threshold for Xoff is about 20KB.
This allows 80KB extra to be stored in this buffer.
8-lane ports use two buffers among which the configured buffer is split,
the Xoff threshold then applies to each buffer in parallel.
The test does not take into account the behavior of 8-lane ports, when the
ports are configured to 400Gbps with 8 lanes or 800Gbps with 8 lanes,
packets are dropped and the test fails.
Check if the relevant ports use 8 lanes, in such case double the size of
the buffer, as the headroom is split half-half.
Cc: Shuah Khan <shuah@kernel.org>
Fixes: bfa804784e ("selftests: mlxsw: Add a PFC test")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/23ff11b7dff031eb04a41c0f5254a2b636cd8ebb.1705502064.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 483ae90d8f ]
When tc filters are first added to a net device, the corresponding local
port gets bound to an ACL group in the device. The group contains a list
of ACLs. In turn, each ACL points to a different TCAM region where the
filters are stored. During forwarding, the ACLs are sequentially
evaluated until a match is found.
One reason to place filters in different regions is when they are added
with decreasing priorities and in an alternating order so that two
consecutive filters can never fit in the same region because of their
key usage.
In Spectrum-2 and newer ASICs the firmware started to report that the
maximum number of ACLs in a group is more than 16, but the layout of the
register that configures ACL groups (PAGT) was not updated to account
for that. It is therefore possible to hit stack corruption [1] in the
rare case where more than 16 ACLs in a group are required.
Fix by limiting the maximum ACL group size to the minimum between what
the firmware reports and the maximum ACLs that fit in the PAGT register.
Add a test case to make sure the machine does not crash when this
condition is hit.
[1]
Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: mlxsw_sp_acl_tcam_group_update+0x116/0x120
[...]
dump_stack_lvl+0x36/0x50
panic+0x305/0x330
__stack_chk_fail+0x15/0x20
mlxsw_sp_acl_tcam_group_update+0x116/0x120
mlxsw_sp_acl_tcam_group_region_attach+0x69/0x110
mlxsw_sp_acl_tcam_vchunk_get+0x492/0xa20
mlxsw_sp_acl_tcam_ventry_add+0x25/0xe0
mlxsw_sp_acl_rule_add+0x47/0x240
mlxsw_sp_flower_replace+0x1a9/0x1d0
tc_setup_cb_add+0xdc/0x1c0
fl_hw_replace_filter+0x146/0x1f0
fl_change+0xc17/0x1360
tc_new_tfilter+0x472/0xb90
rtnetlink_rcv_msg+0x313/0x3b0
netlink_rcv_skb+0x58/0x100
netlink_unicast+0x244/0x390
netlink_sendmsg+0x1e4/0x440
____sys_sendmsg+0x164/0x260
___sys_sendmsg+0x9a/0xe0
__sys_sendmsg+0x7a/0xc0
do_syscall_64+0x40/0xe0
entry_SYSCALL_64_after_hwframe+0x63/0x6b
Fixes: c3ab435466 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Reported-by: Orel Hagag <orelh@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/2d91c89afba59c22587b444994ae419dbea8d876.1705502064.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d6eeabcfa ]
Lately, a bug was found when many TC filters are added - at some point,
several bugs are printed to dmesg [1] and the switch is crashed with
segmentation fault.
The issue starts when gen_pool_free() fails because of unexpected
behavior - a try to free memory which is already freed, this leads to BUG()
call which crashes the switch and makes many other bugs.
Trying to track down the unexpected behavior led to a bug in eRP code. The
function mlxsw_sp_acl_erp_table_alloc() gets a pointer to the allocated
index, sets the value and returns an error code. When gen_pool_alloc()
fails it returns address 0, we track it and return -ENOBUFS outside, BUT
the call for gen_pool_alloc() already override the index in erp_table
structure. This is a problem when such allocation is done as part of
table expansion. This is not a new table, which will not be used in case
of allocation failure. We try to expand eRP table and override the
current index (non-zero) with zero. Then, it leads to an unexpected
behavior when address 0 is freed twice. Note that address 0 is valid in
erp_table->base_index and indeed other tables use it.
gen_pool_alloc() fails in case that there is no space left in the
pre-allocated pool, in our case, the pool is limited to
ACL_MAX_ERPT_BANK_SIZE, which is read from hardware. When more than max
erp entries are required, we exceed the limit and return an error, this
error leads to "Failed to migrate vregion" print.
Fix this by changing erp_table->base_index only in case of a successful
allocation.
Add a test case for such a scenario. Without this fix it causes
segmentation fault:
$ TESTS="max_erp_entries_test" ./tc_flower.sh
./tc_flower.sh: line 988: 1560 Segmentation fault tc filter del dev $h2 ingress chain $i protocol ip pref $i handle $j flower &>/dev/null
[1]:
kernel BUG at lib/genalloc.c:508!
invalid opcode: 0000 [#1] PREEMPT SMP
CPU: 6 PID: 3531 Comm: tc Not tainted 6.7.0-rc5-custom-ga6893f479f5e #1
Hardware name: Mellanox Technologies Ltd. MSN4700/VMOD0010, BIOS 5.11 07/12/2021
RIP: 0010:gen_pool_free_owner+0xc9/0xe0
...
Call Trace:
<TASK>
__mlxsw_sp_acl_erp_table_other_dec+0x70/0xa0 [mlxsw_spectrum]
mlxsw_sp_acl_erp_mask_destroy+0xf5/0x110 [mlxsw_spectrum]
objagg_obj_root_destroy+0x18/0x80 [objagg]
objagg_obj_destroy+0x12c/0x130 [objagg]
mlxsw_sp_acl_erp_mask_put+0x37/0x50 [mlxsw_spectrum]
mlxsw_sp_acl_ctcam_region_entry_remove+0x74/0xa0 [mlxsw_spectrum]
mlxsw_sp_acl_ctcam_entry_del+0x1e/0x40 [mlxsw_spectrum]
mlxsw_sp_acl_tcam_ventry_del+0x78/0xd0 [mlxsw_spectrum]
mlxsw_sp_flower_destroy+0x4d/0x70 [mlxsw_spectrum]
mlxsw_sp_flow_block_cb+0x73/0xb0 [mlxsw_spectrum]
tc_setup_cb_destroy+0xc1/0x180
fl_hw_destroy_filter+0x94/0xc0 [cls_flower]
__fl_delete+0x1ac/0x1c0 [cls_flower]
fl_destroy+0xc2/0x150 [cls_flower]
tcf_proto_destroy+0x1a/0xa0
...
mlxsw_spectrum3 0000:07:00.0: Failed to migrate vregion
mlxsw_spectrum3 0000:07:00.0: Failed to migrate vregion
Fixes: f465261aa1 ("mlxsw: spectrum_acl: Implement common eRP core")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/4cfca254dfc0e5d283974801a24371c7b6db5989.1705502064.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2518da8e6 ]
The tests changed by this patch, as well as the scripts they source, use
features which are not part of POSIX sh (ex. 'source' and 'local'). As a
result, these tests fail when /bin/sh is dash such as on Debian. Change the
interpreter to bash so that these tests can run successfully.
Fixes: d43eff0b85 ("selftests: bonding: up/down delay w/ slave link flapping")
Tested-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 981cf568a8 ]
When building whole selftests on arm64, rsync gives an erorr about sgx:
rsync: [sender] link_stat "/root/linux-next/tools/testing/selftests/sgx/test_encl.elf" failed: No such file or directory (2)
rsync error: some files/attrs were not transferred (see previous errors) (code 23) at main.c(1327) [sender=3.2.5]
The root casue is sgx only used on X86_64, and shall be skipped on other
platforms.
Fix this by moving TEST_CUSTOM_PROGS and TEST_FILES inside the if check,
then the build result will be "Skipping non-existent dir: sgx".
Fixes: 2adcba79e6 ("selftests/x86: Add a selftest for SGX")
Signed-off-by: Zhao Mengmeng <zhaomengmeng@kylinos.cn>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Link: https://lore.kernel.org/all/20231206025605.3965302-1-zhaomzhao%40126.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a33e9da347 ]
When running fib_nexthop_multiprefix test I saw all IPv6 test failed.
e.g.
]# ./fib_nexthop_multiprefix.sh
TEST: IPv4: host 0 to host 1, mtu 1300 [ OK ]
TEST: IPv6: host 0 to host 1, mtu 1300 [FAIL]
With -v it shows
COMMAND: ip netns exec h0 /usr/sbin/ping6 -s 1350 -c5 -w5 2001:db8:101::1
PING 2001:db8:101::1(2001:db8:101::1) 1350 data bytes
From 2001:db8:100::64 icmp_seq=1 Packet too big: mtu=1300
--- 2001:db8:101::1 ping statistics ---
1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms
Route get
2001:db8:101::1 via 2001:db8:100::64 dev eth0 src 2001:db8:100::1 metric 1024 expires 599sec mtu 1300 pref medium
Searching for:
2001:db8:101::1 from :: via 2001:db8:100::64 dev eth0 src 2001:db8:100::1 .* mtu 1300
The reason is when CONFIG_IPV6_SUBTREES is not enabled, rt6_fill_node() will
not put RTA_SRC info. After fix:
]# ./fib_nexthop_multiprefix.sh
TEST: IPv4: host 0 to host 1, mtu 1300 [ OK ]
TEST: IPv6: host 0 to host 1, mtu 1300 [ OK ]
Fixes: 735ab2f65d ("selftests: Add test with multiple prefixes using single nexthop")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://lore.kernel.org/r/20231213060856.4030084-7-liuhangbin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b4a64bafd ]
Privileged programs are supposed to be able to read uninitialized stack
memory (ever since 6715df8d5) but, before this patch, these accesses
were permitted inconsistently. In particular, accesses were permitted
above state->allocated_stack, but not below it. In other words, if the
stack was already "large enough", the access was permitted, but
otherwise the access was rejected instead of being allowed to "grow the
stack". This undesired rejection was happening in two places:
- in check_stack_slot_within_bounds()
- in check_stack_range_initialized()
This patch arranges for these accesses to be permitted. A bunch of tests
that were relying on the old rejection had to change; all of them were
changed to add also run unprivileged, in which case the old behavior
persists. One tests couldn't be updated - global_func16 - because it
can't run unprivileged for other reasons.
This patch also fixes the tracking of the stack size for variable-offset
reads. This second fix is bundled in the same commit as the first one
because they're inter-related. Before this patch, writes to the stack
using registers containing a variable offset (as opposed to registers
with fixed, known values) were not properly contributing to the
function's needed stack size. As a result, it was possible for a program
to verify, but then to attempt to read out-of-bounds data at runtime
because a too small stack had been allocated for it.
Each function tracks the size of the stack it needs in
bpf_subprog_info.stack_depth, which is maintained by
update_stack_depth(). For regular memory accesses, check_mem_access()
was calling update_state_depth() but it was passing in only the fixed
part of the offset register, ignoring the variable offset. This was
incorrect; the minimum possible value of that register should be used
instead.
This tracking is now fixed by centralizing the tracking of stack size in
grow_stack_state(), and by lifting the calls to grow_stack_state() to
check_stack_access_within_bounds() as suggested by Andrii. The code is
now simpler and more convincingly tracks the correct maximum stack size.
check_stack_range_initialized() can now rely on enough stack having been
allocated for the access; this helps with the fix for the first issue.
A few tests were changed to also check the stack depth computation. The
one that fails without this patch is verifier_var_off:stack_write_priv_vs_unpriv.
Fixes: 01f810ace9 ("bpf: Allow variable-offset stack access")
Reported-by: Hao Sun <sunhao.th@gmail.com>
Signed-off-by: Andrei Matei <andreimatei1@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20231208032519.260451-3-andreimatei1@gmail.com
Closes: https://lore.kernel.org/bpf/CABWLsev9g8UP_c3a=1qbuZUi20tGoUXoU07FPf-5FLvhOKOY+Q@mail.gmail.com/
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f770d28f2 ]
When do arping, the interface need to be specified. Or we will
get error: Interface "lo" is not ARPable. And the test failed.
]# ./arp_ndisc_untracked_subnets.sh
TEST: test_arp: accept_arp=0 [ OK ]
TEST: test_arp: accept_arp=1 [FAIL]
TEST: test_arp: accept_arp=2 same_subnet=0 [ OK ]
TEST: test_arp: accept_arp=2 same_subnet=1 [FAIL]
After fix:
]# ./arp_ndisc_untracked_subnets.sh
TEST: test_arp: accept_arp=0 [ OK ]
TEST: test_arp: accept_arp=1 [ OK ]
TEST: test_arp: accept_arp=2 same_subnet=0 [ OK ]
TEST: test_arp: accept_arp=2 same_subnet=1 [ OK ]
Fixes: 0ea7b0a454 ("selftests: net: arp_ndisc_untracked_subnets: test for arp_accept and accept_untracked_na")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9dbd592740 ]
The FPU & VMX preemption tests do not check for errors returned by the
low-level asm routines, preempt_fpu() / preempt_vsx() respectively.
That means any register corruption detected by the asm routines does not
result in a test failure.
Fix it by returning the return value of the asm routines from the
pthread child routines.
Fixes: e5ab8be68e ("selftests/powerpc: Test preservation of FPU and VMX regs across preemption")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20231128132748.1990179-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61fa2493ca ]
Similar to commit be80942465 ("selftests: bonding: do not set port down
before adding to bond"). The bond-arp-interval-causes-panic test failed
after commit a4abfa627c ("net: rtnetlink: Enslave device before bringing
it up") as the kernel will set the port down _after_ adding to bond if setting
port down specifically.
Fix it by removing the link down operation when adding to bond.
Fixes: 2ffd57327f ("selftests: bonding: cause oops in bond_rr_gen_slave_id")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Tested-by: Benjamin Poirier <benjamin.poirier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4249f13c11 upstream.
mas_preallocate() defaults to requesting 1 node for preallocation and then
,depending on the type of store, will update the request variable. There
isn't a check for a slot store type, so slot stores are preallocating the
default 1 node. Slot stores do not require any additional nodes, so add a
check for the slot store case that will bypass node_count_gfp(). Update
the tests to reflect that slot stores do not require allocations.
User visible effects of this bug include increased memory usage from the
unneeded node that was allocated.
Link: https://lkml.kernel.org/r/20231213205058.386589-1-sidhartha.kumar@oracle.com
Fixes: 0b8bb544b1 ("maple_tree: update mas_preallocate() testing")
Signed-off-by: Sidhartha Kumar <sidhartha.kumar@oracle.com>
Cc: Liam R. Howlett <Liam.Howlett@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Peng Zhang <zhangpeng.00@bytedance.com>
Cc: <stable@vger.kernel.org> [6.6+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8f021eec5 upstream.
MPC backups tests will skip unexpected sometimes (For example, when
compiling kernel with an older version of gcc, such as gcc-8), since
static functions like mptcp_subflow_send_ack also be listed in
/proc/kallsyms, with a 't' in front of it, not 'T' ('T' is for a global
function):
> grep "mptcp_subflow_send_ack" /proc/kallsyms
0000000000000000 T __pfx___mptcp_subflow_send_ack
0000000000000000 T __mptcp_subflow_send_ack
0000000000000000 t __pfx_mptcp_subflow_send_ack
0000000000000000 t mptcp_subflow_send_ack
In this case, mptcp_lib_kallsyms_doesnt_have "mptcp_subflow_send_ack$"
will be false, MPC backups tests will skip. This is not what we expected.
The correct logic here should be: if mptcp_subflow_send_ack is not a
global function in /proc/kallsyms, do these MPC backups tests. So a 'T'
must be added in front of mptcp_subflow_send_ack.
Fixes: 632978f0a9 ("selftests: mptcp: join: skip MPC backups tests if not supported")
Cc: stable@vger.kernel.org
Signed-off-by: Geliang Tang <geliang.tang@linux.dev>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts <matttbe@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f40bfd1679 ]
This is a preparatory change. A follow-up patch "bpf: verify callbacks
as if they are called unknown number of times" changes logic for
callbacks handling. While previously callbacks were verified as a
single function call, new scheme takes into account that callbacks
could be executed unknown number of times.
This has dire implications for bpf_loop_bench:
SEC("fentry/" SYS_PREFIX "sys_getpgid")
int benchmark(void *ctx)
{
for (int i = 0; i < 1000; i++) {
bpf_loop(nr_loops, empty_callback, NULL, 0);
__sync_add_and_fetch(&hits, nr_loops);
}
return 0;
}
W/o callbacks change verifier sees it as a 1000 calls to
empty_callback(). However, with callbacks change things become
exponential:
- i=0: state exploring empty_callback is scheduled with i=0 (a);
- i=1: state exploring empty_callback is scheduled with i=1;
...
- i=999: state exploring empty_callback is scheduled with i=999;
- state (a) is popped from stack;
- i=1: state exploring empty_callback is scheduled with i=1;
...
Avoid this issue by rewriting outer loop as bpf_loop().
Unfortunately, this adds a function call to a loop at runtime, which
negatively affects performance:
throughput latency
before: 149.919 ± 0.168 M ops/s, 6.670 ns/op
after : 137.040 ± 0.187 M ops/s, 7.297 ns/op
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20231121020701.26440-4-eddyz87@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6fcd57cf2 ]
Doing a ksft_print_msg() before the ksft_print_header() seems to confuse
the ksft framework in a strange way: running the test on the cmdline
results in the expected output.
But piping the output somewhere else, results in some odd output,
whereby we repeatedly get the same info printed:
# [INFO] detected THP size: 2048 KiB
# [INFO] detected hugetlb page size: 2048 KiB
# [INFO] detected hugetlb page size: 1048576 KiB
# [INFO] huge zeropage is enabled
TAP version 13
1..190
# [INFO] Anonymous memory tests in private mappings
# [RUN] Basic COW after fork() ... with base page
# [INFO] detected THP size: 2048 KiB
# [INFO] detected hugetlb page size: 2048 KiB
# [INFO] detected hugetlb page size: 1048576 KiB
# [INFO] huge zeropage is enabled
TAP version 13
1..190
# [INFO] Anonymous memory tests in private mappings
# [RUN] Basic COW after fork() ... with base page
ok 1 No leak from parent into child
# [RUN] Basic COW after fork() ... with swapped out base page
# [INFO] detected THP size: 2048 KiB
# [INFO] detected hugetlb page size: 2048 KiB
# [INFO] detected hugetlb page size: 1048576 KiB
# [INFO] huge zeropage is enabled
Doing the ksft_print_header() first seems to resolve that and gives us
the output we expect:
TAP version 13
# [INFO] detected THP size: 2048 KiB
# [INFO] detected hugetlb page size: 2048 KiB
# [INFO] detected hugetlb page size: 1048576 KiB
# [INFO] huge zeropage is enabled
1..190
# [INFO] Anonymous memory tests in private mappings
# [RUN] Basic COW after fork() ... with base page
ok 1 No leak from parent into child
# [RUN] Basic COW after fork() ... with swapped out base page
ok 2 No leak from parent into child
# [RUN] Basic COW after fork() ... with THP
ok 3 No leak from parent into child
# [RUN] Basic COW after fork() ... with swapped-out THP
ok 4 No leak from parent into child
# [RUN] Basic COW after fork() ... with PTE-mapped THP
ok 5 No leak from parent into child
Link: https://lkml.kernel.org/r/20231206103558.38040-1-david@redhat.com
Fixes: f4b5fd6946 ("selftests/vm: anon_cow: THP tests")
Signed-off-by: David Hildenbrand <david@redhat.com>
Reported-by: Nico Pache <npache@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 00a4f8fd9c ]
Same init_rng() in both tests. The function reads /dev/urandom to
initialize srand(). In case of failure, it falls back onto the
entropy in the uninitialized variable. Not sure if this is on purpose.
But failure reading urandom should be rare, so just fail hard. While
at it, convert to getrandom(). Which man 4 random suggests is simpler
and more robust.
mptcp_inq.c:525:6:
mptcp_connect.c:1131:6:
error: variable 'foo' is used uninitialized
whenever 'if' condition is false
[-Werror,-Wsometimes-uninitialized]
Fixes: 048d19d444 ("mptcp: add basic kselftest for mptcp")
Fixes: b51880568f ("selftests: mptcp: add inq test case")
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: Willem de Bruijn <willemb@google.com>
----
When input is randomized because this is expected to meaningfully
explore edge cases, should we also add
1. logging the random seed to stdout and
2. adding a command line argument to replay from a specific seed
I can do this in net-next, if authors find it useful in this case.
Reviewed-by: Matthieu Baerts <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20231124171645.1011043-5-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b29828c5a ]
Signedness of char is signed on x86_64, but unsigned on arm64.
Fix the warning building cmsg_sender.c on signed platforms or
forced with -fsigned-char:
msg_sender.c:455:12:
error: implicit conversion from 'int' to 'char'
changes value from 128 to -128
[-Werror,-Wconstant-conversion]
buf[0] = ICMPV6_ECHO_REQUEST;
constant ICMPV6_ECHO_REQUEST is 128.
Link: https://lwn.net/Articles/911914
Fixes: de17e305a8 ("selftests: net: cmsg_sender: support icmp and raw sockets")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20231124171645.1011043-3-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0885598154 ]
Fix a small compiler warning.
nr_process must be a signed long: it is assigned a signed long by
strtol() and is compared against LONG_MIN and LONG_MAX.
ipsec.c:2280:65:
error: result of comparison of constant -9223372036854775808
with expression of type 'unsigned int' is always false
[-Werror,-Wtautological-constant-out-of-range-compare]
if ((errno == ERANGE && (nr_process == LONG_MAX || nr_process == LONG_MIN))
Fixes: bc2652b7ae ("selftest/net/xfrm: Add test for ipsec tunnel")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Dmitry Safonov <0x7f454c46@gmail.com>
Link: https://lore.kernel.org/r/20231124171645.1011043-2-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0863888f6 ]
Tune message length calculation to make this test work on machines
where 'getpagesize()' returns >32KB. Now maximum message length is not
hardcoded (on machines above it was smaller than 'getpagesize()' return
value, thus we get negative value and test fails), but calculated at
runtime and always bigger than 'getpagesize()' result. Reproduced on
aarch64 with 64KB page size.
Fixes: 5c338112e4 ("test/vsock: rework message bounds test")
Signed-off-by: Arseniy Krasnov <avkrasnov@salutedevices.com>
Reported-by: Bogdan Marcynkov <bmarcynk@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20231121211642.163474-1-avkrasnov@salutedevices.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7cefbe5e1d upstream.
Running the mp_join selftest manually with the following command line:
./mptcp_join.sh -z -C
leads to some failures:
002 fastclose server test
# ...
rtx [fail] got 1 MP_RST[s] TX expected 0
# ...
rstrx [fail] got 1 MP_RST[s] RX expected 0
The problem is really in the wrong expectations for the RST checks
implied by the csum validation. Note that the same check is repeated
explicitly in the same test-case, with the correct expectation and
pass successfully.
Address the issue explicitly setting the correct expectation for
the failing checks.
Reported-by: Xiumei Mu <xmu@redhat.com>
Fixes: 6bf41020b7 ("selftests: mptcp: update and extend fastclose test-cases")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20231114-upstream-net-20231113-mptcp-misc-fixes-6-7-rc2-v1-5-7b9cd6a7b7f4@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3aff514644 ]
Unmounting resctrl FS has been moved into the per test functions in
resctrl_tests.c by commit caddc0fbe4 ("selftests/resctrl: Move
resctrl FS mount/umount to higher level"). In case a signal (SIGINT,
SIGTERM, or SIGHUP) is received, the running selftest is aborted by
ctrlc_handler() which then unmounts resctrl fs before exiting. The
current section between signal_handler_register() and
signal_handler_unregister(), however, does not cover the entire
duration when resctrl FS is mounted.
Move signal_handler_register() and signal_handler_unregister() calls
from per test files into resctrl_tests.c to properly unmount resctrl
fs. In order to not add signal_handler_register()/unregister() n times,
create helpers test_prepare() and test_cleanup().
Do not call ksft_exit_fail_msg() in test_prepare() but only in the per
test function to keep the control flow cleaner without adding calls to
exit() deep into the call chain.
Adjust child process kill() call in ctrlc_handler() to only be invoked
if the child was already forked.
Fixes: caddc0fbe4 ("selftests/resctrl: Move resctrl FS mount/umount to higher level")
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e33cb5702a ]
Benchmark command is used in multiple tests so it should not be
mutated by the tests but CMT test alters span argument. Due to the
order of tests (CMT test runs last), mutating the span argument in CMT
test does not trigger any real problems currently.
Mark benchmark_cmd strings as const and setup the benchmark command
using pointers. Because the benchmark command becomes const, the input
arguments can be used directly. Besides being simpler, using the input
arguments directly also removes the internal size restriction.
CMT test has to create a copy of the benchmark command before altering
the benchmark command.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: "Wieczor-Retman, Maciej" <maciej.wieczor-retman@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Stable-dep-of: 3aff514644 ("selftests/resctrl: Extend signal handler coverage to unmount on receiving signal")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1a901e078 ]
struct resctrl_val_param contains span member. resctrl_val(), however,
never uses it because the value of span is embedded into the default
benchmark command and parsed from it by run_benchmark().
Remove span from resctrl_val_param. Provide DEFAULT_SPAN for the code
that needs it. CMT and CAT tests communicate span that is different
from the DEFAULT_SPAN between their internal functions which is
converted into passing it directly as a parameter.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: "Wieczor-Retman, Maciej" <maciej.wieczor-retman@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Stable-dep-of: 3aff514644 ("selftests/resctrl: Extend signal handler coverage to unmount on receiving signal")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 98a04c7ace upstream.
Root decoder granularity must match value from CFWMS, which may not
be the region's granularity for non-interleaved root decoders.
So when calculating granularities for host bridge decoders, use the
region's granularity instead of the root decoder's granularity to ensure
the correct granularities are set for the host bridge decoders and any
downstream switch decoders.
Test configuration is 1 host bridge * 2 switches * 2 endpoints per switch.
Region created with 2048 granularity using following command line:
cxl create-region -m -d decoder0.0 -w 4 mem0 mem2 mem1 mem3 \
-g 2048 -s 2048M
Use "cxl list -PDE | grep granularity" to get a view of the granularity
set at each level of the topology.
Before this patch:
"interleave_granularity":2048,
"interleave_granularity":2048,
"interleave_granularity":512,
"interleave_granularity":2048,
"interleave_granularity":2048,
"interleave_granularity":512,
"interleave_granularity":256,
After:
"interleave_granularity":2048,
"interleave_granularity":2048,
"interleave_granularity":4096,
"interleave_granularity":2048,
"interleave_granularity":2048,
"interleave_granularity":4096,
"interleave_granularity":2048,
Fixes: 27b3f8d138 ("cxl/region: Program target lists")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jim Harris <jim.harris@samsung.com>
Link: https://lore.kernel.org/r/169824893473.1403938.16110924262989774582.stgit@bgt-140510-bm03.eng.stellus.in
[djbw: fixup the prebuilt cxl_test region]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc7f04dc23 upstream.
When execute the following command to test clone3 under !CONFIG_TIME_NS:
# make headers && cd tools/testing/selftests/clone3 && make && ./clone3
we can see the following error info:
# [7538] Trying clone3() with flags 0x80 (size 0)
# Invalid argument - Failed to create new process
# [7538] clone3() with flags says: -22 expected 0
not ok 18 [7538] Result (-22) is different than expected (0)
...
# Totals: pass:18 fail:1 xfail:0 xpass:0 skip:0 error:0
This is because if CONFIG_TIME_NS is not set, but the flag
CLONE_NEWTIME (0x80) is used to clone a time namespace, it
will return -EINVAL in copy_time_ns().
If kernel does not support CONFIG_TIME_NS, /proc/self/ns/time
will be not exist, and then we should skip clone3() test with
CLONE_NEWTIME.
With this patch under !CONFIG_TIME_NS:
# make headers && cd tools/testing/selftests/clone3 && make && ./clone3
...
# Time namespaces are not supported
ok 18 # SKIP Skipping clone3() with CLONE_NEWTIME
...
# Totals: pass:18 fail:0 xfail:0 xpass:0 skip:1 error:0
Link: https://lkml.kernel.org/r/1689066814-13295-1-git-send-email-yangtiezhu@loongson.cn
Fixes: 515bddf0ec ("selftests/clone3: test clone3 with CLONE_NEWTIME")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef43c30858 upstream.
The initial value of 5% chosen for the maximum allowed percentage
difference between resctrl mbm value and IMC mbm value in
commit 06bd03a57f ("selftests/resctrl: Fix MBA/MBM results reporting
format") was "randomly chosen value" (as admitted by the changelog).
When running tests in our lab across a large number platforms, 5%
difference upper bound for success seems a bit on the low side for the
MBA and MBM tests. Some platforms produce outliers that are slightly
above that, typically 6-7%, which leads MBA/MBM test frequently
failing.
Replace the "randomly chosen value" with a success bound that is based
on those measurements across large number of platforms by relaxing the
MBA/MBM success bound to 8%. The relaxed bound removes the failures due
the frequent outliers.
Fixed commit description style error during merge:
Shuah Khan <skhan@linuxfoundation.org>
Fixes: 06bd03a57f ("selftests/resctrl: Fix MBA/MBM results reporting format")
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06035f0194 upstream.
The MBA and CMT tests expect support of other features to be able to
run.
When platform only supports MBA but not MBM, MBA test will fail with:
Failed to open total bw file: No such file or directory
When platform only supports CMT but not CAT, CMT test will fail with:
Failed to open bit mask file '/sys/fs/resctrl/info/L3/cbm_mask': No such file or directory
It leads to the test reporting test fail (even if no test was run at
all).
Extend feature checks to cover these two conditions to show these tests
were skipped rather than failed.
Fixes: ee0415681e ("selftests/resctrl: Use resctrl/info for feature detection")
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Cc: <stable@vger.kernel.org> # selftests/resctrl: Refactor feature check to use resource and feature name
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d56e5da0e0 upstream.
Feature check in validate_resctrl_feature_request() takes in the test
name string and maps that to what to check per test.
Pass resource and feature names to validate_resctrl_feature_request()
directly rather than deriving them from the test name inside the
function which makes the feature check easier to extend for new test
cases.
Use !! in the return statement to make the boolean conversion more
obvious even if it is not strictly necessary from correctness point of
view (to avoid it looking like the function is returning a freed
pointer).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Cc: <stable@vger.kernel.org> # selftests/resctrl: Remove duplicate feature check from CMT test
Cc: <stable@vger.kernel.org> # selftests/resctrl: Move _GNU_SOURCE define into Makefile
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a1e4a91aa upstream.
_GNU_SOURCE is defined in resctrl.h. Defining _GNU_SOURCE has a large
impact on what gets defined when including headers either before or
after it. This can result in compile failures if .c file decides to
include a standard header file before resctrl.h.
It is safer to define _GNU_SOURCE in Makefile so it is always defined
regardless of in which order includes are done.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit beb7f47184 upstream.
signal_handler_unregister() calls sigaction() with uninitializing
sa_flags in the struct sigaction.
Make sure sa_flags is always initialized in signal_handler_unregister()
by initializing the struct sigaction when declaring it. Also add the
initialization to signal_handler_register() even if there are no know
bugs in there because correctness is then obvious from the code itself.
Fixes: 73c55fa5ab ("selftests/resctrl: Commonize the signal handler register/unregister for all tests")
Suggested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 10e14e9652 ]
When BPF program is verified in privileged mode, BPF verifier allows
bounded loops. This means that from CFG point of view there are
definitely some back-edges. Original commit adjusted check_cfg() logic
to not detect back-edges in control flow graph if they are resulting
from conditional jumps, which the idea that subsequent full BPF
verification process will determine whether such loops are bounded or
not, and either accept or reject the BPF program. At least that's my
reading of the intent.
Unfortunately, the implementation of this idea doesn't work correctly in
all possible situations. Conditional jump might not result in immediate
back-edge, but just a few unconditional instructions later we can arrive
at back-edge. In such situations check_cfg() would reject BPF program
even in privileged mode, despite it might be bounded loop. Next patch
adds one simple program demonstrating such scenario.
To keep things simple, instead of trying to detect back edges in
privileged mode, just assume every back edge is valid and let subsequent
BPF verification prove or reject bounded loops.
Note a few test changes. For unknown reason, we have a few tests that
are specified to detect a back-edge in a privileged mode, but looking at
their code it seems like the right outcome is passing check_cfg() and
letting subsequent verification to make a decision about bounded or not
bounded looping.
Bounded recursion case is also interesting. The example should pass, as
recursion is limited to just a few levels and so we never reach maximum
number of nested frames and never exhaust maximum stack depth. But the
way that max stack depth logic works today it falsely detects this as
exceeding max nested frame count. This patch series doesn't attempt to
fix this orthogonal problem, so we just adjust expected verifier failure.
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Fixes: 2589726d12 ("bpf: introduce bounded loops")
Reported-by: Hao Sun <sunhao.th@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20231110061412.2995786-1-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3feb263bb5 ]
ldimm64 instructions are 16-byte long, and so have to be handled
appropriately in check_cfg(), just like the rest of BPF verifier does.
This has implications in three places:
- when determining next instruction for non-jump instructions;
- when determining next instruction for callback address ldimm64
instructions (in visit_func_call_insn());
- when checking for unreachable instructions, where second half of
ldimm64 is expected to be unreachable;
We take this also as an opportunity to report jump into the middle of
ldimm64. And adjust few test_verifier tests accordingly.
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Reported-by: Hao Sun <sunhao.th@gmail.com>
Fixes: 475fb78fbf ("bpf: verifier (add branch/goto checks)")
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20231110002638.4168352-2-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
