The High Performance Direct Memory Access (HPDMA) controller is used to
perform programmable data transfers between memory-mapped peripherals
and memories (or between memories) via linked-lists.
There are 3 instances of HPDMA on stm32mp251, using stm32-dma3 driver, with
16 channels per instance and with one interrupt per channel.
Channels 0 to 7 are implemented with a FIFO of 8 bytes.
Channels 8 to 11 are implemented with a FIFO of 32 bytes.
Channels 12 to 15 are implemented with a FIFO of 128 bytes.
Thanks to stm32-dma3 bindings, the user can ask for a channel with specific
FIFO size.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add power domains on STM32MP25x SoC for supported low power modes:
- CPU_PD0/1: domain for idle of each core Cortex A35 (CStop)
- CLUSTER_PD: D1 domain with Stop1 and LP-Stop1 modes support when
the Cortex A35 cluster and each device assigned to CPU1=CA35
are deactivated
- RET_PD: D1 domain retention (VDDCore is reduced) to support
the LPLV-Stop1 mode
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Pull interrupt subsystem updates from Thomas Gleixner:
"Core code:
- Interrupt storm detection for the lockup watchdog:
Lockups which are caused by interrupt storms are not easy to debug
because there is no information about the events which make the
lockup detector trigger.
To make this more user friendly, provide an extenstion to interrupt
statistics which allows to take snapshots and an interface to
retrieve the delta to the snapshot. Use this new mechanism in the
watchdog code to do a two stage lockup analysis by taking the
snapshot and printing the deltas for the topmost active interrupts
on the second trigger.
Note: This contains both the interrupt and the watchdog changes as
the latter depend on the former obviously.
- Avoid summation loops in the /proc/interrupts output and use the
global counter when possible
- Skip suspended interrupts on CPU hotplug operations to ensure that
they are not delivered before the system resumes the device drivers
when coming out of suspend.
- On CPU hot-unplug interrupts which are affine to the outgoing CPU
are migrated to a different CPU in the affinity mask. This can fail
when the CPUs have no vectors left. Instead of giving up try to
migrate it to any online CPU and thereby breaking the affinity
setting in order to prevent a stale device interrupt which targets
an offline CPU
- The usual small cleanups
Driver code:
- Support for the RISCV AIA MSI controller
- Make the interrupt allocation for the Loongson PCH controller more
flexible to prevent vector exhaustion
- The usual set of cleanups and fixes all over the place"
* tag 'irq-core-2024-05-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (51 commits)
irqchip/gic-v3-its: Remove BUG_ON in its_vpe_irq_domain_alloc
cpuidle: Avoid explicit cpumask allocation on stack
irqchip/sifive-plic: Avoid explicit cpumask allocation on stack
irqchip/riscv-aplic-direct: Avoid explicit cpumask allocation on stack
irqchip/loongson-eiointc: Avoid explicit cpumask allocation on stack
irqchip/gic-v3-its: Avoid explicit cpumask allocation on stack
irqchip/irq-bcm6345-l1: Avoid explicit cpumask allocation on stack
cpumask: Introduce cpumask_first_and_and()
irqchip/irq-brcmstb-l2: Avoid saving mask on shutdown
genirq: Reuse irq_is_nmi()
genirq/cpuhotplug: Retry with cpu_online_mask when migration fails
genirq/cpuhotplug: Skip suspended interrupts when restoring affinity
arm64: dts: st: Add interrupt parent to pinctrl on stm32mp251
arm64: dts: st: Add exti1 and exti2 nodes on stm32mp251
ARM: dts: stm32: List exti parent interrupts on stm32mp131
ARM: dts: stm32: List exti parent interrupts on stm32mp151
arm64: Kconfig.platforms: Enable STM32_EXTI for ARCH_STM32
irqchip/stm32-exti: Mark events reserved with RIF configuration check
irqchip/stm32-exti: Skip secure events
irqchip/stm32-exti: Convert driver to standard PM
...
Using GIC_CPU_MASK_SIMPLE(x), x should reflect the number of CPUs.
STM32MP251 is a single core Cortex A35, STM32MP253 is a dual core CA35.
Fixes: 5d30d03aaf ("arm64: dts: st: introduce stm32mp25 SoCs family")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add properties for spi3 and spi8 available on the stm32mp257f-ev1.
Both are kept disabled since only used via the gpio expansion connector.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add properties for i2c2 and i2c8 available on the stm32mp257f-ev1.
i2c2 is enabled since several devices are attached to it while
i2c8 is kept disabled since only used via the gpio expansion connector.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add BSEC support to STM32MP25 SoC family with SoC information:
- RPN = Device part number (BSEC_OTP_DATA9)
- PKG = package data register (Bits 2:0 of BSEC_OTP_DATA122)
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add the node to use the ARM SMC watchdog support. It will
use a dedicated smc-id to configure and kick the watchdog.
Signed-off-by: Lionel Debieve <lionel.debieve@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add the configuration node for SD-card support on STM32MP257F-EV1 board.
For the moment it uses a fixed regulator for vmmc, and vqmmc is skipped
until regulator driver is available.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The SDMMC1 peripheral is used for SD-cards (default on ST boards), or
eMMC cards. For the moment it uses the fixed clock ck_flexgen_51, until
clock driver is available.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add STM32MP257F Evaluation board support. It embeds a STM32MP257FAI SoC,
with 4GB of DDR4, TSN switch (2+1 ports), 2*USB typeA, 1*USB2 typeC,
SNOR OctoSPI, mini PCIe, STPMIC2 for power distribution ...
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Three packages exist for stm32mp25 dies. As ball-out is different between
them, this patch covers those differences by introducing dedicated pinctrl
dtsi files. Each dtsi pinctrl package file describes the package ball-out
through gpio-ranges.
Available packages are:
STM32MP25xAI: 18*18/FCBGA 172 ios
STM32MP25xAK: 14*14/FCBGA 144 ios
STM32MP25xAL: 10*10/TFBGA 144 ios
It includes also the common file used for pin groups definition.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
STM32MP25 family is composed of 4 SoCs defined as following:
-STM32MP251: common part composed of 1*Cortex-A35, common peripherals like
SDMMC, UART, SPI, I2C, PCIe, USB3, parallel and DSI display, 1*ETH ...
-STM32MP253: STM32MP251 + 1*Cortex-A35 (dual CPU), a second ETH, CAN-FD and
LVDS display.
-STM32MP255: STM32MP253 + GPU/AI and video encode/decode.
-STM32MP257: STM32MP255 + ETH TSN switch (2+1 ports).
A second diversity layer exists for security features/ A35 frequency:
-STM32MP25xY, "Y" gives information:
-Y = A means A35@1.2GHz + no cryp IP and no secure boot.
-Y = C means A35@1.2GHz + cryp IP and secure boot.
-Y = D means A35@1.5GHz + no cryp IP and no secure boot.
-Y = F means A35@1.5GHz + cryp IP and secure boot.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Patrick Delaunay
Christian Bruel
Pascal Paillet
Christophe Roullier
Amelie Delaunay
Valentin Caron
Gabriel Fernandez
Etienne Carriere
Linus Torvalds
Alain Volmat
Gatien Chevallier
Antonio Borneo
Hugues Fruchet
Alexandre Torgue
Yann Gautier