commit dedb897f11 upstream.
The hw clock gating register sequence consists of register value pairs
that are written to the GPU during initialisation.
The a690 hwcg sequence has two GMU registers in it that used to amount
to random writes in the GPU mapping, but since commit 188db3d7fe
("drm/msm/a6xx: Rebase GMU register offsets") they trigger a fault as
the updated offsets now lie outside the mapping. This in turn breaks
boot of machines like the Lenovo ThinkPad X13s.
Note that the updates of these GMU registers is already taken care of
properly since commit 40c297eb24 ("drm/msm/a6xx: Set GMU CGC
properties on a6xx too"), but for some reason these two entries were
left in the table.
Fixes: 5e7665b5e4 ("drm/msm/adreno: Add Adreno A690 support")
Cc: stable@vger.kernel.org # 6.5
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Konrad Dybcio <konradybcio@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Akhil P Oommen <akhilpo@oss.qualcomm.com>
Fixes: 188db3d7fe ("drm/msm/a6xx: Rebase GMU register offsets")
Patchwork: https://patchwork.freedesktop.org/patch/695778/
Message-ID: <20251221164552.19990-1-johan@kernel.org>
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
(cherry picked from commit dcbd2f8280)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a3a22373fc ]
If the rootfs have a legacy A200 firmware, currently the driver will
complain each time the hw is reinited (which can happen a lot). E.g.
with GL testsuite the hw is reinited after each test, spamming the
console.
Make sure that the message is printed only once: when we detect the
firmware that doesn't support protection.
Fixes: 302295070d ("drm/msm/a2xx: support loading legacy (iMX) firmware")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/688098/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f248d5d515 ]
Since the PDC resides out of the GPU subsystem and cannot be reset in
case it enters bad state, utmost care must be taken to trigger the PDC
wake/sleep routines in the correct order.
The PDC wake sequence can be exercised only after a PDC sleep sequence.
Additionally, GMU firmware should initialize a few registers before the
KMD can trigger a PDC sleep sequence. So PDC sleep can't be done if the
GMU firmware has not initialized. Track these dependencies using a new
status variable and trigger PDC sleep/wake sequences appropriately.
Cc: stable@vger.kernel.org
Fixes: 4b565ca5a2 ("drm/msm: Add A6XX device support")
Signed-off-by: Akhil P Oommen <akhilpo@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/673362/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
[ Adjust context ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2b520c6104 ]
Calling this packet is necessary when we switch contexts because there
are various pieces of state used by userspace to synchronize between BR
and BV that are persistent across submits and we need to make sure that
they are in a "safe" state when switching contexts. Otherwise a
userspace submission in one context could cause another context to
function incorrectly and hang, effectively a denial of service (although
without leaking data). This was missed during initial a7xx bringup.
Fixes: af66706acc ("drm/msm/a6xx: Add skeleton A7xx support")
Signed-off-by: Connor Abbott <cwabbott0@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/654924/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f561db72a6 upstream.
It was observed on sc7180 (A618 gpu) that GPU votes for GX rail and CNOC
BCM nodes were not removed after GPU suspend. This was because we
skipped sending 'prepare-slumber' request to gmu during suspend sequence
in some cases. So, make sure we always call prepare-slumber hfi during
suspend. Also, calling prepare-slumber without a prior oob-gpu handshake
messes up gmu firmware's internal state. So, do that when required.
Fixes: 4b565ca5a2 ("drm/msm: Add A6XX device support")
Cc: stable@vger.kernel.org
Signed-off-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/639569/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9d78f02503 ]
IB_SIZE is only b0..b19. Starting with a6xx gen3, additional fields
were added above the IB_SIZE. Accidentially setting them can cause
badness. Fix this by properly defining the CP_INDIRECT_BUFFER packet
and using the generated builder macro to ensure unintended bits are not
set.
v2: add missing type attribute for IB_BASE
v3: fix offset attribute in xml
Reported-by: Connor Abbott <cwabbott0@gmail.com>
Fixes: a83366ef19 ("drm/msm/a6xx: add A640/A650 to gpulist")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/643396/
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06dd5d86c6 ]
Somehow, possibly as a result of rebase gone badly, setting
nr_indexed_regs for pre-a650 a6xx devices lost the setting of
nr_indexed_regs, resulting in values getting snapshot, but omitted
from the devcoredump.
Fixes: e997ae5f45 ("drm/msm/a6xx: Mostly implement A7xx gpu_state")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/640289/
Signed-off-by: Sasha Levin <sashal@kernel.org>
The CP_SMMU_TABLE_UPDATE _should_ be waiting for idle, but on some
devices (x1-85, possibly others), it seems to pass that barrier while
there are still things in the event completion FIFO waiting to be
written back to memory.
Work around that by adding a fence wait before context switch. The
CP_EVENT_WRITE that writes the fence is the last write from a submit,
so seeing this value hit memory is a reliable indication that it is
safe to proceed with the context switch.
v2: Only emit CP_WAIT_TIMESTAMP on a7xx, as it is not supported on a6xx.
Conversely, I've not been able to reproduce this issue on a6xx, so
hopefully it is limited to a7xx, or perhaps just certain a7xx
devices.
Fixes: af66706acc ("drm/msm/a6xx: Add skeleton A7xx support")
Closes: https://gitlab.freedesktop.org/drm/msm/-/issues/63
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Store the correct values that we happen to have for some A7xx SKUs in
the GPU info struct and fill out the missing information for A6xx GPUs
based on downstream kernel information.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/611094/
[add missing entry to a615 catalog to resolve conflict]
Signed-off-by: Rob Clark <robdclark@chromium.org>
There is another cause for soft lock-up of GPU in empty ring-buffer:
race between GPU executing last commands and CPU checking ring for
emptiness. On GPU side IRQ for retire is triggered by CACHE_FLUSH_TS
event and RPTR shadow (which is used to check ring emptiness) is updated
a bit later from CP_CONTEXT_SWITCH_YIELD. Thus if GPU is executing its
last commands slow enough or we check that ring too fast we will miss a
chance to trigger switch to lower priority ring because current ring isn't
empty just yet. This can escalate to lock-up situation described in
previous patch.
To work-around this issue we keep track of last submit sequence number
for each ring and compare it with one written to memptrs from GPU during
execution of CACHE_FLUSH_TS event.
Fixes: b1fc2839d2 ("drm/msm: Implement preemption for A5XX targets")
Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/612047/
Signed-off-by: Rob Clark <robdclark@chromium.org>
On A5XX GPUs when preemption is used it's invietable to enter a soft
lock-up state in which GPU is stuck at empty ring-buffer doing nothing.
This appears as full UI lockup and not detected as GPU hang (because
it's not). This happens due to not triggering preemption when it was
needed. Sometimes this state can be recovered by some new submit but
generally it won't happen because applications are waiting for old
submits to retire.
One of the reasons why this happens is a race between a5xx_submit and
a5xx_preempt_trigger called from IRQ during submit retire. Former thread
updates ring->cur of previously empty and not current ring right after
latter checks it for emptiness. Then both threads can just exit because
for first one preempt_state wasn't NONE yet and for second one all rings
appeared to be empty.
To prevent such situations from happening we need to establish guarantee
for preempt_trigger to make decision after each submit or retire. To
implement this we serialize preemption initiation using spinlock. If
switch is already in progress we need to re-trigger preemption when it
finishes.
Fixes: b1fc2839d2 ("drm/msm: Implement preemption for A5XX targets")
Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/612045/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Two fields of preempt_record which are used by CP aren't reset on
resume: "data" and "info". This is the reason behind faults which happen
when we try to switch to the ring that was active last before suspend.
In addition those faults can't be recovered from because we use suspend
and resume to do so (keeping values of those fields again).
Fixes: b1fc2839d2 ("drm/msm: Implement preemption for A5XX targets")
Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/612043/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fine grain preemption (switching from/to points within submits)
requires extra handling in command stream of those submits, especially
when rendering with tiling (using GMEM). However this handling is
missing at this point in mesa (and always was). For this reason we get
random GPU faults and hangs if more than one priority level is used
because local preemption is enabled prior to executing command stream
from submit.
With that said it was ahead of time to enable local preemption by
default considering the fact that even on downstream kernel it is only
enabled if requested via UAPI.
Fixes: a7a4c19c36 ("drm/msm/a5xx: fix setting of the CP_PREEMPT_ENABLE_LOCAL register")
Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/612041/
Signed-off-by: Rob Clark <robdclark@chromium.org>
There are some cases, such as the one uncovered by Commit 46d4efcccc
("drm/msm/a6xx: Avoid a nullptr dereference when speedbin setting fails")
where
msm_gpu_cleanup() : platform_set_drvdata(gpu->pdev, NULL);
is called on gpu->pdev == NULL, as the GPU device has not been fully
initialized yet.
Turns out that there's more than just the aforementioned path that
causes this to happen (e.g. the case when there's speedbin data in the
catalog, but opp-supported-hw is missing in DT).
Assigning msm_gpu->pdev earlier seems like the least painful solution
to this, therefore do so.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/602742/
Signed-off-by: Rob Clark <robdclark@chromium.org>
In adreno_request_fw() when debugging information is printed to the log
after firmware load, an incorrect filename is printed. 'newname' is used
instead of 'fwname', so prefix "qcom/" is being added to filename.
Looks like "copy-paste" mistake.
Fix this mistake by replacing 'newname' with 'fwname'.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 2c41ef1b6f ("drm/msm/adreno: deal with linux-firmware fw paths")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/602382/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Make it match the MDSS settings for sc8180x and downstream.
Note that without the previous commit that exposes the value of
macrotile_mode to mesa, this will break mesa which expects the legacy
default value of 0. Therefore we do *not* want to backport it.
Signed-off-by: Connor Abbott <cwabbott0@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/607398/
Signed-off-by: Rob Clark <robdclark@chromium.org>
According to downstream we should be setting RBBM_NC_MODE_CNTL to a
non-default value on a663 and a680, we don't support a663 and on a680
we're leaving it at the wrong (suboptimal) value. Just set it on all
GPUs. Similarly, plumb through level2_swizzling_dis which will be
necessary on a663.
ubwc_mode is expanded and renamed to ubwc_swizzle to match the name on
the display side. Similarly macrotile_mode should match the display
side.
Signed-off-by: Connor Abbott <cwabbott0@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/607397/
Signed-off-by: Rob Clark <robdclark@chromium.org>
With a7xx, we need to import a new header for each new generation and
switch to a different list of registers, instead of making
backwards-compatible changes. Using the helpers inadvertently made a750
use the a740 list of registers, instead use the family directly to fix
this.
Fixes: f3f8207d8a ("drm/msm: Add devcoredump support for a750")
Signed-off-by: Connor Abbott <cwabbott0@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/607392/
Signed-off-by: Rob Clark <robdclark@chromium.org>
-ENODEV is used to signify that there is no zap shader for the platform,
and the CPU can directly take the GPU out of secure mode. We want to
use this return code when there is no zap-shader node. But not when
there is, but without a firmware-name property. This case we want to
treat as-if the needed fw is not found.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/604564/
Disable the call to qcom_scm_gpu_init_regs() for a730 and a740
after init failures on the HDK8550 and HDK8450 platforms:
msm_dpu ae01000.display-controller: failed to load adreno gpu
msm_dpu ae01000.display-controller: failed to bind 3d00000.gpu (ops a3xx_ops [msm]): -5
msm_dpu ae01000.display-controller: adev bind failed: -5
While debugging, it happens the call to:
qcom_scm_gpu_init_regs(QCOM_SCM_GPU_ALWAYS_EN_REQ)
returns -5 and makes the gpu fail to initialize.
Remove the scm call since it's not done downstream either and
works fine without.
Fixes: 14b27d5df3 ("drm/msm/a7xx: Initialize a750 "software fuse"")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Connor Abbott <cwabbott0@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/600972/
Signed-off-by: Rob Clark <robdclark@chromium.org>
The gpulist has twice the a6xx gpulist, replace the second one
with the a7xx gpulist.
Solves:
msm_dpu ae01000.display-controller: Unknown GPU revision: 7.3.0.1
msm_dpu ae01000.display-controller: Unknown GPU revision: 67.5.10.1
msm_dpu ae01000.display-controller: Unknown GPU revision: 67.5.20.1
on SM8450, SM8550 & SM8560.
Fixes: 8ed322f632 ("drm/msm/adreno: Split up giant device table")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/600939/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Commit f6ebff4fe810 ("drm/msm/adreno: De-spaghettify the use of memory
barriers") made some fixups relating to write arrival, ensuring that
the GPU's memory interface has *really really really* been told to come
out of reset. That in turn rendered the hacky commit being reverted no
longer necessary.
Get rid of it.
This reverts commit b77532803d ("drm/msm/a6xx: Poll for GBIF unhalt
status in hw_init")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/600870/
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Memory barriers help ensure instruction ordering, NOT time and order
of actual write arrival at other observers (e.g. memory-mapped IP).
On architectures employing weak memory ordering, the latter can be a
giant pain point, and it has been as part of this driver.
Moreover, the gpu_/gmu_ accessors already use non-relaxed versions of
readl/writel, which include r/w (respectively) barriers.
Replace the barriers with a readback (or drop altogether where possible)
that ensures the previous writes have exited the write buffer (as the CPU
must flush the write to the register it's trying to read back).
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/600869/
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Dmitry Baryshkov
Johan Hovold
Akhil P Oommen
Antonino Maniscalco
Connor Abbott
Konrad Dybcio
Akhil P Oommen
Rob Clark
Sui Jingfeng
Jinjie Ruan
Otto Pflüger
Konrad Dybcio
Vladimir Lypak
Aleksandr Mishin
Richard Acayan
Eugene Lepshy
Li Zetao
Daniil Titov
Neil Armstrong