[ Upstream commit 1072020685 ]
PLIC ignores interrupt completion message for disabled interrupt, explained
by the specification:
The PLIC signals it has completed executing an interrupt handler by
writing the interrupt ID it received from the claim to the
claim/complete register. The PLIC does not check whether the completion
ID is the same as the last claim ID for that target. If the completion
ID does not match an interrupt source that is currently enabled for
the target, the completion is silently ignored.
This caused problems in the past, because an interrupt can be disabled
while still being handled and plic_irq_eoi() had no effect. That was fixed
by checking if the interrupt is disabled, and if so enable it, before
sending the completion message. That check is done with irqd_irq_disabled().
However, that is not sufficient because the enable bit for the handling
hart can be zero despite irqd_irq_disabled(d) being false. This can happen
when affinity setting is changed while a hart is still handling the
interrupt.
This problem is easily reproducible by dumping a large file to uart (which
generates lots of interrupts) and at the same time keep changing the uart
interrupt's affinity setting. The uart port becomes frozen almost
instantaneously.
Fix this by checking PLIC's enable bit instead of irqd_irq_disabled().
Fixes: cc9f04f9a8 ("irqchip/sifive-plic: Implement irq_set_affinity() for SMP host")
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Link: https://patch.msgid.link/20260212114125.3148067-1-namcao@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8d76a7d89c upstream.
On 32-bit machines with CONFIG_ARM_LPAE, it is possible for lowmem
allocations to be backed by addresses physical memory above the 32-bit
address limit, as found while experimenting with larger VMSPLIT
configurations.
This caused the qemu virt model to crash in the GICv3 driver, which
allocates the 'itt' object using GFP_KERNEL. Since all memory below
the 4GB physical address limit is in ZONE_DMA in this configuration,
kmalloc() defaults to higher addresses for ZONE_NORMAL, and the
ITS driver stores the physical address in a 32-bit 'unsigned long'
variable.
Change the itt_addr variable to the correct phys_addr_t type instead,
along with all other variables in this driver that hold a physical
address.
The gicv5 driver correctly uses u64 variables, while all other irqchip
drivers don't call virt_to_phys or similar interfaces. It's expected that
other device drivers have similar issues, but fixing this one is
sufficient for booting a virtio based guest.
Fixes: cc2d3216f5 ("irqchip: GICv3: ITS command queue")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260119201603.2713066-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9b685058ca ]
Platform drivers can be probed after their init sections have been
discarded so the probe callback must not live in init.
Fixes: f20cc9b00c ("irqchip/qcom: Add IRQ combiner driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f798bdb9aa ]
Platform drivers can be probed after their init sections have been
discarded so the irqchip init callback must not live in init.
Fixes: e4e5350361 ("irqchip: Add StarFive external interrupt controller")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Changhuang Liang <changhuang.liang@starfivetech.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b338fbb2b ]
Platform drivers can be probed after their init sections have been
discarded so the irqchip init callbacks must not live in init.
Fixes: d011c022ef ("irqchip/renesas-rzg2l: Add support for RZ/Five SoC")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64acfd8e68 ]
Platform drivers can be probed after their init sections have been
discarded so the irqchip init callbacks must not live in init.
Fixes: 70afdab904 ("irqchip: Add IMX MU MSI controller driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbe1775924 ]
Platform drivers can be probed after their init sections have been
discarded so the irqchip init callbacks must not live in init.
Fixes: 51d9db5c8f ("irqchip/irq-brcmstb-l2: Switch to IRQCHIP_PLATFORM_DRIVER")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfc0c5beab ]
Platform drivers can be probed after their init sections have been
discarded so the irqchip init callbacks must not live in init.
Fixes: 3ac268d5ed ("irqchip/irq-bcm7120-l2: Switch to IRQCHIP_PLATFORM_DRIVER")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9db5332ca ]
Platform drivers can be probed after their init sections have been
discarded so the irqchip init callback must not live in init.
Fixes: c057c799e3 ("irqchip/irq-bcm7038-l1: Switch to IRQCHIP_PLATFORM_DRIVER")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14473a1f88 ]
The irq_domain_free_irqs() helper requires that the irq_domain_ops->free
callback is implemented. Otherwise, the kernel reports the warning message
"NULL pointer, cannot free irq" when irq_dispose_mapping() is invoked to
release the per-HART local interrupts.
Set irq_domain_ops->free to irq_domain_free_irqs_top() to cure that.
Fixes: 832f15f426 ("RISC-V: Treat IPIs as normal Linux IRQs")
Signed-off-by: Nick Hu <nick.hu@sifive.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://patch.msgid.link/20251114-rv-intc-fix-v1-1-a3edd1c1a868@sifive.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c33c43f71b ]
On certain Loongson platforms, drivers attempting to request a legacy
ISA IRQ directly via request_irq() (e.g., IRQ 4) may fail. The
virtual IRQ descriptor is not fully initialized and lacks a valid irqchip.
This issue does not affect ACPI-enumerated devices described in DSDT,
as their interrupts are properly mapped via the GSI translation path.
This indicates the LPC irqdomain itself is functional but is not correctly
handling direct VIRQ-to-HWIRQ mappings.
The root cause is the use of irq_domain_create_linear(). This API sets
up a domain for dynamic, on-demand mapping, typically triggered by a GSI
request. It does not pre-populate the mappings for the legacy VIRQ range
(0-15). Consequently, if no ACPI device claims a specific GSI
(e.g., GSI 4), the corresponding VIRQ (e.g., VIRQ 4) is never mapped to
the LPC domain. A direct call to request_irq(4, ...) then fails because
the kernel cannot resolve this VIRQ to a hardware interrupt managed by
the LPC controller.
The PCH-LPC interrupt controller is an i8259-compatible legacy device
that requires a deterministic, static 1-to-1 mapping for IRQs 0-15 to
support legacy drivers.
Fix this by replacing irq_domain_create_linear() with
irq_domain_create_legacy(). This API is specifically designed for such
controllers. It establishes the required static 1-to-1 VIRQ-to-HWIRQ
mapping for the entire legacy range (0-15) immediately upon domain
creation. This ensures that any VIRQ in this range is always resolvable,
making direct calls to request_irq() for legacy IRQs function correctly.
Signed-off-by: Ming Wang <wangming01@loongson.cn>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ef3886ce6 ]
The PCI Local Bus Specification 3.0 (section 6.8.1.6) allows modifying the
low-order bits of the MSI Message DATA register to encode nr_irqs interrupt
numbers in the log2(nr_irqs) bits for the domain.
The problem arises if the base vector (GICV2m base spi) is not aligned with
nr_irqs; in this case, the low-order log2(nr_irqs) bits from the base
vector conflict with the nr_irqs masking, causing the wrong MSI interrupt
to be identified.
To fix this, use bitmap_find_next_zero_area_off() instead of
bitmap_find_free_region() to align the initial base vector with nr_irqs.
Signed-off-by: Christian Bruel <christian.bruel@foss.st.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/all/20250902091045.220847-1-christian.bruel@foss.st.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f75e07bf52 ]
According to the PLIC specification[1], global interrupt sources are
assigned small unsigned integer identifiers beginning at the value 1.
An interrupt ID of 0 is reserved to mean "no interrupt".
The current plic_irq_resume() and plic_irq_suspend() functions incorrectly
start the loop from index 0, which accesses the register space for the
reserved interrupt ID 0.
Change the loop to start from index 1, skipping the reserved
interrupt ID 0 as per the PLIC specification.
This prevents potential undefined behavior when accessing the reserved
register space during suspend/resume cycles.
Fixes: e80f0b6a2c ("irqchip/irq-sifive-plic: Add syscore callbacks for hibernation")
Co-developed-by: Jia Wang <wangjia@ultrarisc.com>
Signed-off-by: Jia Wang <wangjia@ultrarisc.com>
Co-developed-by: Charles Mirabile <cmirabil@redhat.com>
Signed-off-by: Charles Mirabile <cmirabil@redhat.com>
Signed-off-by: Lucas Zampieri <lzampier@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://github.com/riscv/riscv-plic-spec/releases/tag/1.0.0
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b6a18f0da ]
Compile-testing IMX_MU_MSI on x86 without PCI_MSI support results in a
build failure:
drivers/gpio/gpio-sprd.c:8:
include/linux/gpio/driver.h:41:33: error: field 'msiinfo' has incomplete type
drivers/iommu/iommufd/viommu.c:4:
include/linux/msi.h:528:33: error: field 'alloc_info' has incomplete type
Tighten the dependency further to only allow compile testing on Arm.
This could be refined further to allow certain x86 configs.
This was submitted before to address a different build failure, which was
fixed differently, but the problem has now returned in a different form.
Fixes: 70afdab904 ("irqchip: Add IMX MU MSI controller driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250805160952.4006075-1-arnd@kernel.org
Link: https://lore.kernel.org/all/20221215164109.761427-1-arnd@kernel.org/
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08fb624802 ]
When starting the local sync timer to synchronize the state of a remote
CPU it should be added on the CPU to be synchronized, not the initiating
CPU. This results in interrupt delivery being delayed until the timer
eventually runs (due to another mask/unmask/migrate operation) on the
target CPU.
Fixes: 0f67911e82 ("irqchip/riscv-imsic: Separate next and previous pointers in IMSIC vector")
Signed-off-by: Andrew Bresticker <abrestic@rivosinc.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/all/20250514171320.3494917-1-abrestic@rivosinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b93afe8a3a ]
RISC-V APLIC specification defines "hart index" in:
https://github.com/riscv/riscv-aia
Within a given interrupt domain, each of the domain’s harts has a unique
index number in the range 0 to 2^14 − 1 (= 16,383). The index number a
domain associates with a hart may or may not have any relationship to the
unique hart identifier (“hart ID”) that the RISC-V Privileged Architecture
assigns to the hart. Two different interrupt domains may employ entirely
different index numbers for the same set of harts.
Further, this document says in "4.5 Memory-mapped control region for an
interrupt domain":
The array of IDC structures may include some for potential hart index
numbers that are not actual hart index numbers in the domain. For example,
the first IDC structure is always for hart index 0, but 0 is not
necessarily a valid index number for any hart in the domain.
Support arbitrary hart indices specified in an optional APLIC property
"riscv,hart-indexes" which is specified as an array of u32 elements, one
per interrupt target. If this property is not specified, fallback to use
logical hart indices within the domain.
Signed-off-by: Vladimir Kondratiev <vladimir.kondratiev@mobileye.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/all/20250129091637.1667279-3-vladimir.kondratiev@mobileye.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 999f458c17 ]
The IMSIC driver assigns the IMSIC domain specific imsic_irq_set_affinity()
callback to the per device leaf MSI domain. That's a layering violation as
it is called with the leaf domain data and not with the IMSIC domain
data. This prevents moving the IMSIC driver to the common MSI library which
uses the generic msi_domain_set_affinity() callback for device MSI domains.
Instead of using imsic_irq_set_affinity() for leaf MSI domains, use
imsic_irq_set_affinity() for the non-leaf IMSIC base domain and use
irq_chip_set_affinity_parent() for leaf MSI domains.
[ tglx: Massaged change log ]
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250217085657.789309-2-apatel@ventanamicro.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f67911e82 ]
Currently, there is only one "move" pointer in struct imsic_vector so
during vector movement the old vector points to the new vector and new
vector points to itself.
To support forced cleanup of the old vector, add separate "move_next" and
"move_prev" pointers to struct imsic_vector, where during vector movement
the "move_next" pointer of the old vector points to the new vector and the
"move_prev" pointer of the new vector points to the old vector.
Both "move_next" and "move_prev" pointers are cleared separately by
__imsic_local_sync() with a restriction that "move_prev" on the new
CPU is cleared only after the old CPU has cleared "move_next".
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250217085657.789309-8-apatel@ventanamicro.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 38a05c0b87 upstream.
On Qualcomm chipsets not all GPIOs are wakeup capable. Those GPIOs do not
have a corresponding MPM pin and should not be handled inside the MPM
driver. The IRQ domain hierarchy is always applied, so it's required to
explicitly disconnect the hierarchy for those. The pinctrl-msm driver marks
these with GPIO_NO_WAKE_IRQ. qcom-pdc has a check for this, but
irq-qcom-mpm is currently missing the check. This is causing crashes when
setting up interrupts for non-wake GPIOs:
root@rb1:~# gpiomon -c gpiochip1 10
irq: IRQ159: trimming hierarchy from :soc@0:interrupt-controller@f200000-1
Unable to handle kernel paging request at virtual address ffff8000a1dc3820
Hardware name: Qualcomm Technologies, Inc. Robotics RB1 (DT)
pc : mpm_set_type+0x80/0xcc
lr : mpm_set_type+0x5c/0xcc
Call trace:
mpm_set_type+0x80/0xcc (P)
qcom_mpm_set_type+0x64/0x158
irq_chip_set_type_parent+0x20/0x38
msm_gpio_irq_set_type+0x50/0x530
__irq_set_trigger+0x60/0x184
__setup_irq+0x304/0x6bc
request_threaded_irq+0xc8/0x19c
edge_detector_setup+0x260/0x364
linereq_create+0x420/0x5a8
gpio_ioctl+0x2d4/0x6c0
Fix this by copying the check for GPIO_NO_WAKE_IRQ from qcom-pdc.c, so that
MPM is removed entirely from the hierarchy for non-wake GPIOs.
Fixes: a6199bb514 ("irqchip: Add Qualcomm MPM controller driver")
Reported-by: Alexey Klimov <alexey.klimov@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexey Klimov <alexey.klimov@linaro.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20250502-irq-qcom-mpm-fix-no-wake-v1-1-8a1eafcd28d4@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3318dc299b upstream.
With ACPI in place, gicv2m_get_fwnode() is registered with the pci
subsystem as pci_msi_get_fwnode_cb(), which may get invoked at runtime
during a PCI host bridge probe. But, the call back is wrongly marked as
__init, causing it to be freed, while being registered with the PCI
subsystem and could trigger:
Unable to handle kernel paging request at virtual address ffff8000816c0400
gicv2m_get_fwnode+0x0/0x58 (P)
pci_set_bus_msi_domain+0x74/0x88
pci_register_host_bridge+0x194/0x548
This is easily reproducible on a Juno board with ACPI boot.
Retain the function for later use.
Fixes: 0644b3daca ("irqchip/gic-v2m: acpi: Introducing GICv2m ACPI support")
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4cb7779384 upstream.
Christoph reports that their rk3399 system dies since commit 773c05f417
("irqchip/gic-v3: Work around insecure GIC integrations").
It appears that some rk3399 have secure payloads, and that the firmware
sets SCR_EL3.FIQ==1. Obivously, disabling security in that configuration
leads to even more problems.
Revisit the workaround by:
- making it rk3399 specific
- checking whether Group-0 is available, which is a good proxy
for SCR_EL3.FIQ being 0
- either apply the workaround if Group-0 is available, or disable
pseudo-NMIs if not
Note that this doesn't mean that the secure side is able to receive
interrupts, as all interrupts are made non-secure anyway.
Clearly, nobody ever tested secure interrupts on this platform.
Fixes: 773c05f417 ("irqchip/gic-v3: Work around insecure GIC integrations")
Reported-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Christoph Fritz <chf.fritz@googlemail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20250215185241.3768218-1-maz@kernel.org
Closes: https://lore.kernel.org/r/b1266652fb64857246e8babdf268d0df8f0c36d9.camel@googlemail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d7e3fd6582 ]
The jcore-aic irqchip does not have separate interrupt numbers reserved for
cpu-local vs global interrupts. Therefore the device drivers need to
request the given interrupt as per CPU interrupt.
69a9dcbd2d ("clocksource/drivers/jcore: Use request_percpu_irq()")
converted the clocksource driver over to request_percpu_irq(), but failed
to do add all the required changes, resulting in a failure to register PIT
interrupts.
Fix this by:
1) Explicitly mark the interrupt via irq_set_percpu_devid() in
jcore_pit_init().
2) Enable and disable the per CPU interrupt in the CPU hotplug callbacks.
3) Pass the correct per-cpu cookie to the irq handler by using
handle_percpu_devid_irq() instead of handle_percpu_irq() in
handle_jcore_irq().
[ tglx: Massage change log ]
Fixes: 69a9dcbd2d ("clocksource/drivers/jcore: Use request_percpu_irq()")
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Uros Bizjak <ubizjak@gmail.com>
Link: https://lore.kernel.org/all/20250216175545.35079-3-contact@artur-rojek.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 698244bbb3 upstream.
The CPU PMU in Apple SoCs can be configured to fire its interrupt in one of
several ways, and since Apple A11 one of the methods is FIQ, but the check
of the configuration register fails to test explicitely for FIQ mode. It
tests whether the IMODE bitfield is zero or not and the PMCRO_IACT bit is
set. That results in false positives when the IMODE bitfield is not zero,
but does not have the mode PMCR0_IMODE_FIQ.
Only handle the PMC interrupt as a FIQ when the CPU PMU has been configured
to fire FIQs, i.e. the IMODE bitfield value is PMCR0_IMODE_FIQ and
PMCR0_IACT is set.
Fixes: c7708816c9 ("irqchip/apple-aic: Wire PMU interrupts")
Signed-off-by: Nick Chan <towinchenmi@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20250118163554.16733-1-towinchenmi@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 987f379b54 upstream.
mvebu_icu_translate() incorrectly casts irq_domain::host_data directly to
mvebu_icu_msi_data. However, host_data actually points to a structure of
type msi_domain_info.
This incorrect cast causes issues such as the thermal sensors of the
CP110 platform malfunctioning. Specifically, the translation of the SEI
interrupt to IRQ_TYPE_EDGE_RISING fails, preventing proper interrupt
handling. The following error was observed:
genirq: Setting trigger mode 4 for irq 85 failed (irq_chip_set_type_parent+0x0/0x34)
armada_thermal f2400000.system-controller:thermal-sensor@70: Cannot request threaded IRQ 85
Resolve the issue by first casting host_data to msi_domain_info and then
accessing mvebu_icu_msi_data through msi_domain_info::chip_data.
Fixes: d929e4db22 ("irqchip/irq-mvebu-icu: Prepare for real per device MSI")
Signed-off-by: Stefan Eichenberger <eichest@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20250124085140.44792-1-eichest@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3a748d483d ]
Some boards with Allwinner SoCs connect the PMIC's IRQ pin to the SoC's NMI
pin instead of a normal GPIO. Since the power key is connected to the PMIC,
and people expect to wake up a suspended system via this key, the NMI IRQ
controller must stay alive when the system goes into suspend.
Add the SKIP_WAKE flag to prevent the sunxi NMI controller from going to
sleep, so that the power key can wake up those systems.
[ tglx: Fixed up coding style ]
Signed-off-by: Philippe Simons <simons.philippe@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250112123402.388520-1-simons.philippe@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 35cb2c6ce7 upstream.
The following call-chain leads to enabling interrupts in a nested interrupt
disabled section:
irq_set_vcpu_affinity()
irq_get_desc_lock()
raw_spin_lock_irqsave() <--- Disable interrupts
its_irq_set_vcpu_affinity()
guard(raw_spinlock_irq) <--- Enables interrupts when leaving the guard()
irq_put_desc_unlock() <--- Warns because interrupts are enabled
This was broken in commit b97e8a2f71, which replaced the original
raw_spin_[un]lock() pair with guard(raw_spinlock_irq).
Fix the issue by using guard(raw_spinlock).
[ tglx: Massaged change log ]
Fixes: b97e8a2f71 ("irqchip/gic-v3-its: Fix potential race condition in its_vlpi_prop_update()")
Signed-off-by: Tomas Krcka <krckatom@amazon.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20241230150825.62894-1-krckatom@amazon.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d62a49ab5 upstream.
When a CPU attempts to enter low power mode, it disables the redistributor
and Group 1 interrupts and reinitializes the system registers upon wakeup.
If the transition into low power mode fails, then the CPU_PM framework
invokes the PM notifier callback with CPU_PM_ENTER_FAILED to allow the
drivers to undo the state changes.
The GIC V3 driver ignores CPU_PM_ENTER_FAILED, which leaves the GIC in
disabled state.
Handle CPU_PM_ENTER_FAILED in the same way as CPU_PM_EXIT to restore normal
operation.
[ tglx: Massage change log, add Fixes tag ]
Fixes: 3708d52fc6 ("irqchip: gic-v3: Implement CPU PM notifier")
Signed-off-by: Yogesh Lal <quic_ylal@quicinc.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20241220093907.2747601-1-quic_ylal@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a1855f1b7c ]
percpu_base is used in various percpu functions that expect variable in
__percpu address space. Correct the declaration of percpu_base to
void __iomem * __percpu *percpu_base;
to declare the variable as __percpu pointer.
The patch fixes several sparse warnings:
irq-gic.c:1172:44: warning: incorrect type in assignment (different address spaces)
irq-gic.c:1172:44: expected void [noderef] __percpu *[noderef] __iomem *percpu_base
irq-gic.c:1172:44: got void [noderef] __iomem *[noderef] __percpu *
...
irq-gic.c:1231:43: warning: incorrect type in argument 1 (different address spaces)
irq-gic.c:1231:43: expected void [noderef] __percpu *__pdata
irq-gic.c:1231:43: got void [noderef] __percpu *[noderef] __iomem *percpu_base
There were no changes in the resulting object files.
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/all/20241213145809.2918-2-ubizjak@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 773c05f417 upstream.
It appears that the relatively popular RK3399 SoC has been put together
using a large amount of illicit substances, as experiments reveal that its
integration of GIC500 exposes the *secure* programming interface to
non-secure.
This has some pretty bad effects on the way priorities are handled, and
results in a dead machine if booting with pseudo-NMI enabled
(irqchip.gicv3_pseudo_nmi=1) if the kernel contains 18fdb6348c ("arm64:
irqchip/gic-v3: Select priorities at boot time"), which relies on the
priorities being programmed using the NS view.
Let's restore some sanity by going one step further and disable security
altogether in this case. This is not any worse, and puts us in a mode where
priorities actually make some sense.
Huge thanks to Mark Kettenis who initially identified this issue on
OpenBSD, and to Chen-Yu Tsai who reported the problem in Linux.
Fixes: 18fdb6348c ("arm64: irqchip/gic-v3: Select priorities at boot time")
Reported-by: Mark Kettenis <mark.kettenis@xs4all.nl>
Reported-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20241213141037.3995049-1-maz@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f82e62d470 ]
When enabling GICv4.1 in hip09, VMAPP fails to clear some caches during
the unmap operation, which can causes vSGIs to be lost.
To fix the issue, invalidate the related vPE cache through GICR_INVALLR
after VMOVP.
Suggested-by: Marc Zyngier <maz@kernel.org>
Co-developed-by: Nianyao Tang <tangnianyao@huawei.com>
Signed-off-by: Nianyao Tang <tangnianyao@huawei.com>
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 12aaf67584 upstream.
Commit fbdf14e90c ("irqchip/irq-mvebu-sei: Switch to MSI parent")
introduced in v6.11-rc1 broke Mavell Armada platforms (and possibly others)
by incorrectly switching irq-mvebu-sei to MSI parent.
In the above commit, msi_parent_ops is set for the sei->cp_domain, but
rather than adding a .select method to mvebu_sei_cp_domain_ops (which is
associated with sei->cp_domain), it was added to mvebu_sei_domain_ops which
is associated with sei->sei_domain, which doesn't have any
msi_parent_ops. This makes the call to msi_lib_irq_domain_select() always
fail.
This bug manifests itself with the following kernel messages on Armada 8040
based systems:
platform f21e0000.interrupt-controller:interrupt-controller@50: deferred probe pending: (reason unknown)
platform f41e0000.interrupt-controller:interrupt-controller@50: deferred probe pending: (reason unknown)
Move the select callback to mvebu_sei_cp_domain_ops to cure it.
Fixes: fbdf14e90c ("irqchip/irq-mvebu-sei: Switch to MSI parent")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/E1tE6bh-004CmX-QU@rmk-PC.armlinux.org.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1f181d1cda ]
If the APLIC driver is probed before the IMSIC driver, the parent MSI
domain will be missing, which causes a NULL pointer dereference in
msi_create_device_irq_domain().
Avoid this by deferring probe until the parent MSI domain is available. Use
dev_err_probe() to avoid printing an error message when returning
-EPROBE_DEFER.
Fixes: ca8df97fe6 ("irqchip/riscv-aplic: Add support for MSI-mode")
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20241114200133.3069460-1-samuel.holland@sifive.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Christoffer reports that on some implementations, writing to
GICR_ISACTIVER0 (and similar GICD registers) can race badly with a guest
issuing a deactivation of that interrupt via the system register interface.
There are multiple reasons to this:
- this uses an early write-acknoledgement memory type (nGnRE), meaning
that the write may only have made it as far as some interconnect
by the time the store is considered "done"
- the GIC itself is allowed to buffer the write until it decides to
take it into account (as long as it is in finite time)
The effects are that the activation may not have taken effect by the time
the kernel enters the guest, forcing an immediate exit, or that a guest
deactivation occurs before the interrupt is active, doing nothing.
In order to guarantee that the write to the ISACTIVER register has taken
effect, read back from it, forcing the interconnect to propagate the write,
and the GIC to process the write before returning the read.
Reported-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20241106084418.3794612-1-maz@kernel.org
rzg2l_irqc_common_init() calls of_find_device_by_node(), but the
corresponding put_device() call is missing. This also gets reported by
make coccicheck.
Make use of the cleanup interfaces from cleanup.h to call into
__free_put_device(), which in turn calls into put_device when leaving
function rzg2l_irqc_common_init() and variable "dev" goes out of scope.
To prevent that the device is put on successful completion, assign NULL to
"dev" to prevent __free_put_device() from calling into put_device() within
the successful path.
"make coccicheck" will still complain about missing put_device() calls,
but those are false positives now.
Fixes: 3fed09559c ("irqchip: Add RZ/G2L IA55 Interrupt Controller driver")
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20241011172003.1242841-1-fabrizio.castro.jz@renesas.com
It is possible that an interrupt is disabled and masked at the same time.
When the interrupt is enabled again by enable_irq(), only plic_irq_enable()
is called, not plic_irq_unmask(). The interrupt remains masked and never
raises.
An example where interrupt is both disabled and masked is when
handle_fasteoi_irq() is the handler, and IRQS_ONESHOT is set. The interrupt
handler:
1. Mask the interrupt
2. Handle the interrupt
3. Check if interrupt is still enabled, and unmask it (see
cond_unmask_eoi_irq())
If another task disables the interrupt in the middle of the above steps,
the interrupt will not get unmasked, and will remain masked when it is
enabled in the future.
The problem is occasionally observed when PREEMPT_RT is enabled, because
PREEMPT_RT adds the IRQS_ONESHOT flag. But PREEMPT_RT only makes the problem
more likely to appear, the bug has been around since commit a1706a1c50
("irqchip/sifive-plic: Separate the enable and mask operations").
Fix it by unmasking interrupt in plic_irq_enable().
Fixes: a1706a1c50 ("irqchip/sifive-plic: Separate the enable and mask operations")
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20241003084152.2422969-1-namcao@linutronix.de
Controllers, supported by this driver, have two sets of registers:
* (main) interrupt registers control peripheral interrupt sources.
* device interrupt registers configure per-device (network interface)
interrupts and act as an extra stage before the main interrupt
registers.
In the driver unmask code, device trigger registers are used in the mask
calculation of the main interrupt sticky register, mixing two kinds of
registers.
Use the main interrupt trigger register instead.
Signed-off-by: Sergey Matsievskiy <matsievskiysv@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20240925184416.54204-2-matsievskiysv@gmail.com
Commit b5712bf89b ("irqchip/gic-v3-its: Provide MSI parent for
PCI/MSI[-X]") moves the functionality of irq-gic-v3-its-pci-msi.c into
irq-gic-v3-its-msi-parent.c, and drops the former file.
With that, the config option ARM_GIC_V3_ITS_PCI is obsolete, but the
definition of that config was not removed in the commit above.
Remove this obsolete config ARM_GIC_V3_ITS_PCI.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20240926125502.363364-1-lukas.bulwahn@redhat.com
