[ Upstream commit 2c27aaee93 ]
Do read-modify-write so that we re-use the characterized reset value as
specified in TRM [1] to program calibration wait time which defines number
of cycles to wait for after startup state machine is in bandgap enable
state.
This fixes PLL lock timeout error faced while using RPi DSI Panel on TI's
AM62L and J721E SoC since earlier calibration wait time was getting
overwritten to zero value thus failing the PLL to lockup and causing
timeout.
[1] AM62P TRM (Section 14.8.6.3.2.1.1 DPHY_TX_DPHYTX_CMN0_CMN_DIG_TBIT2):
Link: https://www.ti.com/lit/pdf/spruj83
Cc: stable@vger.kernel.org
Fixes: 7a343c8bf4 ("phy: Add Cadence D-PHY support")
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Tested-by: Harikrishna Shenoy <h-shenoy@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://lore.kernel.org/r/20250704125915.1224738-3-devarsht@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 284fb19a3f ]
PLL lockup and O_CMN_READY assertion can only happen after common state
machine gets enabled by programming DPHY_CMN_SSM register, but driver was
polling them before the common state machine was enabled which is
incorrect. This is as per the DPHY initialization sequence as mentioned in
J721E TRM [1] at section "12.7.2.4.1.2.1 Start-up Sequence Timing Diagram".
It shows O_CMN_READY polling at the end after common configuration pin
setup where the common configuration pin setup step enables state machine
as referenced in "Table 12-1533. Common Configuration-Related Setup
mentions state machine"
To fix this :
- Add new function callbacks for polling on PLL lock and O_CMN_READY
assertion.
- As state machine and clocks get enabled in power_on callback only, move
the clock related programming part from configure callback to power_on
callback and poll for the PLL lockup and O_CMN_READY assertion after state
machine gets enabled.
- The configure callback only saves the PLL configuration received from the
client driver which will be applied later on in power_on callback.
- Add checks to ensure configure is called before power_on and state
machine is in disabled state before power_on callback is called.
- Disable state machine in power_off so that client driver can re-configure
the PLL by following up a power_off, configure, power_on sequence.
[1]: https://www.ti.com/lit/zip/spruil1
Cc: stable@vger.kernel.org
Fixes: 7a343c8bf4 ("phy: Add Cadence D-PHY support")
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Tested-by: Harikrishna Shenoy <h-shenoy@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://lore.kernel.org/r/20250704125915.1224738-2-devarsht@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Torrent SERDES can support at most two different protocols (PHY types).
This only mandates that the device-tree sub-nodes used to represent the
configuration should describe links with at-most two different protocols.
The existing implementation however imposes an artificial constraint that
allows only two links (device-tree sub-nodes). As long as at-most two
protocols are chosen, using more than two links to describe them in an
alternating configuration is still a valid configuration of the Torrent
SERDES.
A 3-Link 2-Protocol configuration of the 4-Lane SERDES can be:
Lane 0 => Protocol 1 => Link 1
Lane 1 => Protocol 1 => Link 1
Lane 2 => Protocol 2 => Link 2
Lane 3 => Protocol 1 => Link 3
A 4-Link 2-Protocol configuration of the 4-Lane SERDES can be:
Lane 0 => Protocol 1 => Link 1
Lane 1 => Protocol 2 => Link 2
Lane 2 => Protocol 1 => Link 3
Lane 3 => Protocol 2 => Link 4
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240805092607.143869-1-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'cdns_sierra_pll_mux_table' is not modified in this driver.
And it is only used as a "const u32 *".
Constifying this structure moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
60937 3894 16 64847 fd4f drivers/phy/cadence/phy-cadence-sierra.o
After:
=====
text data bss dec hex filename
60897 3878 16 64791 fd17 drivers/phy/cadence/phy-cadence-sierra.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/43d881d52e3c1632ad197d4c2c18b6c481a13b24.1720723132.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'struct cdns_sierra_vals' is not modified in this driver.
Constifying this structure moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
60521 4310 16 64847 fd4f drivers/phy/cadence/phy-cadence-sierra.o
After:
=====
text data bss dec hex filename
60937 3894 16 64847 fd4f drivers/phy/cadence/phy-cadence-sierra.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/0ccfd259fdf40475c89cfb22a64c6388e7c646b4.1720723132.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'struct cdns_reg_pairs' is not modified in this driver.
Constifying this structure moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
60489 4342 16 64847 fd4f drivers/phy/cadence/phy-cadence-sierra.o
After:
=====
text data bss dec hex filename
60521 4310 16 64847 fd4f drivers/phy/cadence/phy-cadence-sierra.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/c57ee8206ebba8c222d7d954335654384072b9ac.1720723132.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'cdns_torrent_refclk_driver_mux_table' is not modified in this driver.
And it is only used as a "const u32 *".
Constifying this structure moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
93578 4798 16 98392 18058 drivers/phy/cadence/phy-cadence-torrent.o
After:
=====
text data bss dec hex filename
93606 4790 16 98412 1806c drivers/phy/cadence/phy-cadence-torrent.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/34e23ceb6b7b7eb730ee8deee21d231b504dc65f.1720718240.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'struct cdns_torrent_vals' is not modified in this driver.
Constifying this structure moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
92234 6078 16 98328 18018 drivers/phy/cadence/phy-cadence-torrent.o
After:
=====
text data bss dec hex filename
93578 4798 16 98392 18058 drivers/phy/cadence/phy-cadence-torrent.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/d9d135ee9b806726766a1bc5e1404267939aa637.1720718240.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'struct cdns_torrent_vals_entry' is not modified in this driver.
Constifying this structure moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
85130 13214 16 98360 18038 drivers/phy/cadence/phy-cadence-torrent.o
After:
=====
text data bss dec hex filename
92234 6078 16 98328 18018 drivers/phy/cadence/phy-cadence-torrent.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/dcc4e539999a840b3fd8f40fd8fd7523390232ac.1720718240.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'struct cdns_reg_pairs' is not modified in this driver.
Constifying this structure moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
78154 20222 16 98392 18058 drivers/phy/cadence/phy-cadence-torrent.o
After:
=====
text data bss dec hex filename
85130 13214 16 98360 18038 drivers/phy/cadence/phy-cadence-torrent.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/803684a6f0c24d7e091dc8d285dd49c6fd31a010.1720718240.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Even if a PHY is already configured, the PHY operations are needed during
resume stage, as the PHY is in reset state.
The noop_ops PHY operations is removed to always have PHY operations.
The already_configured flag is checked at the begening of init, configure
and poweron operations to keep the already_configured behaviour.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://lore.kernel.org/r/20240412-j7200-phy-s2r-v1-7-f15815833974@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add a separate compatible and registers map table for TI J7200.
TI J7200 uses Torrent SD0805 version which is a special version
derived from Torrent SD0801 with some differences in register
configurations.
Add register sequences for USXGMII(156.25MHz) + SGMII/QSGMII(100MHz)
multilink config for TI J7200. USXGMII uses PLL0 and SGMII/QSGMII
uses PLL1.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240104133013.2911035-6-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for drivers/phy/phy-can-transceiver.c
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20230714174841.4061919-1-robh@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Instead of a 3D matrix use a key:value pair table for link_cmn_vals,
xcvr_diag_vals, pcs_cmn_vals, phy_pma_cmn_vals, cmn_vals,
tx_ln_vals and rx_ln_vals. This makes it scaleable for multiple
reference clocks.
Wherever both CDNS and TI use the same settings, reuse the same data.
Introduce CLK_ANY and ANY_SSC enums which are used if the setting
is independent of clock rate or SSC type.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20230530143853.26571-3-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pull phy updates from Vinod Koul:
"New Support:
- Debugfs support for phy core and mediatek driver
- Hisilicon inno-usb2-phy driver supporting Hi3798MV100
- Qualcomm SGMII SerDes PHY driver, SM6115 & QCM2290 QMP-USB support,
SA8775P USB PHY & USB3 UNI support, QUSB2 support for IPQ9574,
IPQ9574 USB3 PHY
UpdatesL
- Sparx5 serdes phy power optimzation
- cadence salvo usb properties and updates and torrent DP with PCIe &
USB support
- Yaml conversion for Broadcom kona USB bindings and MXS USB binding"
* tag 'phy-for-6.5_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (67 commits)
dt-bindings: phy: brcm,brcmstb-usb-phy: Fix error in "compatible" conditional schema
dt-bindings: phy: mixel,mipi-dsi-phy: Remove assigned-clock* properties
dt-bindings: phy: intel,combo-phy: restrict node name suffixes
dt-bindings: phy: qcom,usb-hs-phy: Add compatible
phy: tegra: xusb: check return value of devm_kzalloc()
phy: qcom: qmp-combo: fix Display Port PHY configuration for SM8550
phy: qcom: add the SGMII SerDes PHY driver
dt-bindings: phy: describe the Qualcomm SGMII PHY
phy: qualcomm: fix indentation in Makefile
phy: usb: suppress OC condition for 7439b2
phy: usb: Turn off phy when port is in suspend
phy: tegra: xusb: Clear the driver reference in usb-phy dev
dt-bindings: phy: mxs-usb-phy: add imx8ulp and imx8qm compatible
dt-bindings: phy: mxs-usb-phy: convert to DT schema format
dt-bindings: phy: qcom,qmp-usb: fix bindings error
dt-bindings: phy: qcom,qmp-ufs: fix the sc8180x regs
dt-bindings: phy: qcom,qmp-pcie: fix the sc8180x regs
phy: mediatek: tphy: add debugfs files
phy: core: add debugfs files
phy: fsl-imx8mp-usb: add support for phy tuning
...
The Cadence Torrent refclk clock implements a mux with a set_parent
hook, but doesn't provide a determine_rate implementation.
This is a bit odd, since set_parent() is there to, as its name implies,
change the parent of a clock. However, the most likely candidate to
trigger that parent change is a call to clk_set_rate(), with
determine_rate() figuring out which parent is the best suited for a
given rate.
The other trigger would be a call to clk_set_parent(), but it's far less
used, and it doesn't look like there's any obvious user for that clock.
So, the set_parent hook is effectively unused, possibly because of an
oversight. However, it could also be an explicit decision by the
original author to avoid any reparenting but through an explicit call to
clk_set_parent().
The latter case would be equivalent to setting the flag
CLK_SET_RATE_NO_REPARENT, together with setting our determine_rate hook
to __clk_mux_determine_rate(). Indeed, if no determine_rate
implementation is provided, clk_round_rate() (through
clk_core_round_rate_nolock()) will call itself on the parent if
CLK_SET_RATE_PARENT is set, and will not change the clock rate
otherwise.
And if it was an oversight, then we are at least explicit about our
behavior now and it can be further refined down the line.
Since the CLK_SET_RATE_NO_REPARENT flag was already set though, it seems
unlikely.
Cc: Kishon Vijay Abraham I <kishon@kernel.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: linux-phy@lists.infradead.org
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20221018-clk-range-checks-fixes-v4-42-971d5077e7d2@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Cadence Sierra PLL clock implements a mux with a set_parent hook,
but doesn't provide a determine_rate implementation.
This is a bit odd, since set_parent() is there to, as its name implies,
change the parent of a clock. However, the most likely candidate to
trigger that parent change is a call to clk_set_rate(), with
determine_rate() figuring out which parent is the best suited for a
given rate.
The other trigger would be a call to clk_set_parent(), but it's far less
used, and it doesn't look like there's any obvious user for that clock.
So, the set_parent hook is effectively unused, possibly because of an
oversight. However, it could also be an explicit decision by the
original author to avoid any reparenting but through an explicit call to
clk_set_parent().
The latter case would be equivalent to setting the flag
CLK_SET_RATE_NO_REPARENT, together with setting our determine_rate hook
to __clk_mux_determine_rate(). Indeed, if no determine_rate
implementation is provided, clk_round_rate() (through
clk_core_round_rate_nolock()) will call itself on the parent if
CLK_SET_RATE_PARENT is set, and will not change the clock rate
otherwise.
And if it was an oversight, then we are at least explicit about our
behavior now and it can be further refined down the line.
Since the CLK_SET_RATE_NO_REPARENT flag was already set though, it seems
unlikely.
Cc: Kishon Vijay Abraham I <kishon@kernel.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: linux-phy@lists.infradead.org
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20221018-clk-range-checks-fixes-v4-41-971d5077e7d2@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
For NXP platform design, the PHY can't know VBUS well, it causes the FSM
in controller seeing the disconnection at L1 use case. With .set_mode API
introduced, the controller driver could force PHY seeing B Session VALID
when it is at the device mode (VBUS is there), and keep FSM working well.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20230517161646.3418250-5-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Very limited parts may fail to work on full speed mode (both host and
device modes) for USB3 port due to higher threshold in full speed receiver
of USB2.0 PHY.
One example failure symptom is, the enumeration is failed when connecting
full speed USB mouse to USB3 port, especially under high temperature.
The workaround is to configure threshold voltage value of single ended
receiver by setting USB2.0 PHY register AFE_RX_REG5[2:0] to 3'b101.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20230517161646.3418250-4-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For USB2 L1 use cases, some hosts may start transferring less than 20us
after End of Resume, it causes the host seeing corrupt packet from the
device side. The reason is the delay time between PHY powers up and
txvalid is 20us. To fix it, we change the delay value as 0us.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20230517161646.3418250-3-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add multilink DP configuration support for 100MHz reference clock rate.
This is the only clock rate supported currently for multilink PHY
configurations. Also, add PCIe + DP multiprotocol multilink register
configuration sequences for 100MHz refclk with no SSC.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20230418173157.25607-4-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch prepares driver for multilink DP support as well as for
multiprotocol PHY configurations involving DP as one of the required
protocols. This needs changes in functions configuring default single
link DP with master lane 0 to support non-zero master lane values and
associated PLL configurations.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20230418173157.25607-3-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Torrent PHY PLL0 or PLL1 is used for DP depending on the single link or
multilink protocol configuration for which PHY is configured. In multilink
configurations with other protocols, either PLL0 or PLL1 will be used
for DP. For single link DP, both PLLs need to be configured at POR.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20230418173157.25607-2-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
DPHY RX module has a common module reset (RSTB_CMN) which is expected
to be released during configuration. In J721E SR1.0 the RSTB_CMN is
internally tied to CSI_RX_RST and is hardware controlled, for all
other newer platforms the common module reset is software controlled.
Add support to control common module reset during configuration and
also skip common module reset based on soc_device_match() for J721E SR1.0.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Co-developed-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20230314073137.2153-1-vaishnav.a@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Rather than requesting the parent reference clocks for the sierra PHY PLLs
and then assigning the parents as a struct clk. Use the clk_parent_data
feature for the clock framework and only specify the firmware names of the
parent clocks.
The clock framework internally will then translate this to the actual
clocks. This allows to remove a bit of boilerplate code.
It also allows to only specify a single reference clock for both PLLs,
which is a valid use case. The clock framework can handle the case where
not all inputs for a clock mux are connected, while the custom
implementation in the driver could not.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20230326011416.363318-2-lars@metafoo.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The `devm_clk_register()` API is deprecated. Switch to
`devm_clk_hw_register()`.
Since the driver enables its own internal PLLs using the clock API we
still need to get a reference to the PLL clocks using the
`devm_clk_hw_get_clk()` API.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20230326011416.363318-1-lars@metafoo.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230307115900.2293120-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230307115900.2293120-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230307115900.2293120-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver state struct for the sierra PHY driver has a field named
`regmap` that is never referenced. Remove it since it is unused.
Not that there are separate fields of type `struct regmap` for the
individual sections of the device's register map. These other regmaps are
used and not affected by the patch.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20220707071722.44201-2-lars@metafoo.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver state struct for the sierra PHY driver has a field named
`regmap` that is never referenced. Remove it since it is unused.
Not that there are separate fields of type `struct regmap` for the
individual sections of the device's register map. These other regmaps are
used and not affected by the patch.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20220707071722.44201-1-lars@metafoo.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
