commit d77b6ff0ce upstream.
batadv_nc_skb_decode_packet() trusts coded_len and checks only against
skb->len. XOR starts at sizeof(struct batadv_unicast_packet), reducing
payload headroom, and the source skb length is not verified, allowing an
out-of-bounds read and a small out-of-bounds write.
Validate that coded_len fits within the payload area of both destination
and source sk_buffs before XORing.
Fixes: 2df5278b02 ("batman-adv: network coding - receive coded packets and decode them")
Cc: stable@vger.kernel.org
Reported-by: Stanislav Fort <disclosure@aisle.com>
Signed-off-by: Stanislav Fort <stanislav.fort@aisle.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 548b0c5de7 upstream.
An OGMv1 and OGMv2 packet receive processing were not only limited by the
number of bytes in the received packet but also by the nodes maximum
aggregation packet size limit. But this limit is relevant for TX and not
for RX. It must not be enforced by batadv_(i)v_ogm_aggr_packet to avoid
loss of information in case of a different limit for sender and receiver.
This has a minor side effect for B.A.T.M.A.N. IV because the
batadv_iv_ogm_aggr_packet is also used for the preprocessing for the TX.
But since the aggregation code itself will not allow more than
BATADV_MAX_AGGREGATION_BYTES bytes, this check was never triggering (in
this context) prior of removing it.
Cc: stable@vger.kernel.org
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Fixes: 9323158ef9 ("batman-adv: OGMv2 - implement originators logic")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c8ecc98f5 upstream.
The ELP worker needs to calculate new metric values for all neighbors
"reachable" over an interface. Some of the used metric sources require
locks which might need to sleep. This sleep is incompatible with the RCU
list iterator used for the recorded neighbors. The initial approach to work
around of this problem was to queue another work item per neighbor and then
run this in a new context.
Even when this solved the RCU vs might_sleep() conflict, it has a major
problems: Nothing was stopping the work item in case it is not needed
anymore - for example because one of the related interfaces was removed or
the batman-adv module was unloaded - resulting in potential invalid memory
accesses.
Directly canceling the metric worker also has various problems:
* cancel_work_sync for a to-be-deactivated interface is called with
rtnl_lock held. But the code in the ELP metric worker also tries to use
rtnl_lock() - which will never return in this case. This also means that
cancel_work_sync would never return because it is waiting for the worker
to finish.
* iterating over the neighbor list for the to-be-deactivated interface is
currently done using the RCU specific methods. Which means that it is
possible to miss items when iterating over it without the associated
spinlock - a behaviour which is acceptable for a periodic metric check
but not for a cleanup routine (which must "stop" all still running
workers)
The better approch is to get rid of the per interface neighbor metric
worker and handle everything in the interface worker. The original problems
are solved by:
* creating a list of neighbors which require new metric information inside
the RCU protected context, gathering the metric according to the new list
outside the RCU protected context
* only use rcu_trylock inside metric gathering code to avoid a deadlock
when the cancel_delayed_work_sync is called in the interface removal code
(which is called with the rtnl_lock held)
Cc: stable@vger.kernel.org
Fixes: c833484e5f ("batman-adv: ELP - compute the metric based on the estimated throughput")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7e34ffc97 upstream.
If a temporary error happened in the evaluation of the neighbor throughput
information, then the invalid throughput result should not be stored in the
throughtput EWMA.
Cc: stable@vger.kernel.org
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ccb7276a6d upstream.
Reference counting is used to ensure that
batadv_hardif_neigh_node and batadv_hard_iface
are not freed before/during
batadv_v_elp_throughput_metric_update work is
finished.
But there isn't a guarantee that the hard if will
remain associated with a soft interface up until
the work is finished.
This fixes a crash triggered by reboot that looks
like this:
Call trace:
batadv_v_mesh_free+0xd0/0x4dc [batman_adv]
batadv_v_elp_throughput_metric_update+0x1c/0xa4
process_one_work+0x178/0x398
worker_thread+0x2e8/0x4d0
kthread+0xd8/0xdc
ret_from_fork+0x10/0x20
(the batadv_v_mesh_free call is misleading,
and does not actually happen)
I was able to make the issue happen more reliably
by changing hardif_neigh->bat_v.metric_work work
to be delayed work. This allowed me to track down
and confirm the fix.
Cc: stable@vger.kernel.org
Fixes: c833484e5f ("batman-adv: ELP - compute the metric based on the estimated throughput")
Signed-off-by: Andy Strohman <andrew@andrewstrohman.com>
[sven@narfation.org: prevent entering batadv_v_elp_get_throughput without
soft_iface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fff8f17c1a ]
When TT changes list is too big to fit in packet due to MTU size, an
empty OGM is sent expected other node to send TT request to get the
changes. The issue is that tt.last_changeset was not built thus the
originator was responding with previous changes to those TT requests
(see batadv_send_my_tt_response). Also the changes list was never
cleaned up effectively never ending growing from this point onwards,
repeatedly sending the same TT response changes over and over, and
creating a new empty OGM every OGM interval expecting for the local
changes to be purged.
When there is more TT changes that can fit in packet, drop all changes,
send empty OGM and wait for TT request so we can respond with a full
table instead.
Fixes: e1bf0c1409 ("batman-adv: tvlv - convert tt data sent within OGMs")
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Acked-by: Antonio Quartulli <Antonio@mandelbit.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8038806db6 ]
The number of entries filled by batadv_tt_tvlv_generate() can be less
than initially expected in batadv_tt_prepare_tvlv_{global,local}_data()
(changes can be removed by batadv_tt_local_event() in ADD+DEL sequence
in the meantime as the lock held during the whole tvlv global/local data
generation).
Thus tvlv_len could be bigger than the actual TT entry size that need
to be sent so full table TT_RESPONSE could hold invalid TT entries such
as below.
* 00:00:00:00:00:00 -1 [....] ( 0) 88:12:4e:ad:7e:ba (179) (0x45845380)
* 00:00:00:00:78:79 4092 [.W..] ( 0) 88:12:4e:ad:7e:3c (145) (0x8ebadb8b)
Remove the extra allocated space to avoid sending uninitialized entries
for full table TT_RESPONSE in both batadv_send_other_tt_response() and
batadv_send_my_tt_response().
Fixes: 7ea7b4a142 ("batman-adv: make the TT CRC logic VLAN specific")
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2f7358c38 ]
The number of TT changes can be less than initially expected in
batadv_tt_tvlv_container_update() (changes can be removed by
batadv_tt_local_event() in ADD+DEL sequence between reading
tt_diff_entries_num and actually iterating the change list under lock).
Thus tt_diff_len could be bigger than the actual changes size that need
to be sent. Because batadv_send_my_tt_response sends the whole
packet, uninitialized data can be interpreted as TT changes on other
nodes leading to weird TT global entries on those nodes such as:
* 00:00:00:00:00:00 -1 [....] ( 0) 88:12:4e:ad:7e:ba (179) (0x45845380)
* 00:00:00:00:78:79 4092 [.W..] ( 0) 88:12:4e:ad:7e:3c (145) (0x8ebadb8b)
All of the above also applies to OGM tvlv container buffer's tvlv_len.
Remove the extra allocated space to avoid sending uninitialized TT
changes in batadv_send_my_tt_response() and batadv_v_ogm_send_softif().
Fixes: e1bf0c1409 ("batman-adv: tvlv - convert tt data sent within OGMs")
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
Pull timer updates from Thomas Gleixner:
"Core:
- Overhaul of posix-timers in preparation of removing the workaround
for periodic timers which have signal delivery ignored.
- Remove the historical extra jiffie in msleep()
msleep() adds an extra jiffie to the timeout value to ensure
minimal sleep time. The timer wheel ensures minimal sleep time
since the large rewrite to a non-cascading wheel, but the extra
jiffie in msleep() remained unnoticed. Remove it.
- Make the timer slack handling correct for realtime tasks.
The procfs interface is inconsistent and does neither reflect
reality nor conforms to the man page. Show the correct 0 slack for
real time tasks and enforce it at the core level instead of having
inconsistent individual checks in various timer setup functions.
- The usual set of updates and enhancements all over the place.
Drivers:
- Allow the ACPI PM timer to be turned off during suspend
- No new drivers
- The usual updates and enhancements in various drivers"
* tag 'timers-core-2024-09-16' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (43 commits)
ntp: Make sure RTC is synchronized when time goes backwards
treewide: Fix wrong singular form of jiffies in comments
cpu: Use already existing usleep_range()
timers: Rename next_expiry_recalc() to be unique
platform/x86:intel/pmc: Fix comment for the pmc_core_acpi_pm_timer_suspend_resume function
clocksource/drivers/jcore: Use request_percpu_irq()
clocksource/drivers/cadence-ttc: Add missing clk_disable_unprepare in ttc_setup_clockevent
clocksource/drivers/asm9260: Add missing clk_disable_unprepare in asm9260_timer_init
clocksource/drivers/qcom: Add missing iounmap() on errors in msm_dt_timer_init()
clocksource/drivers/ingenic: Use devm_clk_get_enabled() helpers
platform/x86:intel/pmc: Enable the ACPI PM Timer to be turned off when suspended
clocksource: acpi_pm: Add external callback for suspend/resume
clocksource/drivers/arm_arch_timer: Using for_each_available_child_of_node_scoped()
dt-bindings: timer: rockchip: Add rk3576 compatible
timers: Annotate possible non critical data race of next_expiry
timers: Remove historical extra jiffie for timeout in msleep()
hrtimer: Use and report correct timerslack values for realtime tasks
hrtimer: Annotate hrtimer_cpu_base_.*_expiry() for sparse.
timers: Add sparse annotation for timer_sync_wait_running().
signal: Replace BUG_ON()s
...
"Interface can't change network namespaces" is rather an attribute,
not a feature, and it can't be changed via Ethtool.
Make it a "cold" private flag instead of a netdev_feature and free
one more bit.
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
NETIF_F_LLTX can't be changed via Ethtool and is not a feature,
rather an attribute, very similar to IFF_NO_QUEUE (and hot).
Free one netdev_features_t bit and make it a "hot" private flag.
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The internal handling of VLAN IDs in batman-adv is only specified for
following encodings:
* VLAN is used
- bit 15 is 1
- bit 11 - bit 0 is the VLAN ID (0-4095)
- remaining bits are 0
* No VLAN is used
- bit 15 is 0
- remaining bits are 0
batman-adv was only preparing new translation table entries (based on its
soft interface information) using this encoding format. But the receive
path was never checking if entries in the roam or TT TVLVs were also
following this encoding.
It was therefore possible to create more than the expected maximum of 4096
+ 1 entries in the originator VLAN list. Simply by setting the "remaining
bits" to "random" values in corresponding TVLV.
Cc: stable@vger.kernel.org
Fixes: 7ea7b4a142 ("batman-adv: make the TT CRC logic VLAN specific")
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
With the rework of how the __string() handles dynamic strings where it
saves off the source string in field in the helper structure[1], the
assignment of that value to the trace event field is stored in the helper
value and does not need to be passed in again.
This means that with:
__string(field, mystring)
Which use to be assigned with __assign_str(field, mystring), no longer
needs the second parameter and it is unused. With this, __assign_str()
will now only get a single parameter.
There's over 700 users of __assign_str() and because coccinelle does not
handle the TRACE_EVENT() macro I ended up using the following sed script:
git grep -l __assign_str | while read a ; do
sed -e 's/\(__assign_str([^,]*[^ ,]\) *,[^;]*/\1)/' $a > /tmp/test-file;
mv /tmp/test-file $a;
done
I then searched for __assign_str() that did not end with ';' as those
were multi line assignments that the sed script above would fail to catch.
Note, the same updates will need to be done for:
__assign_str_len()
__assign_rel_str()
__assign_rel_str_len()
I tested this with both an allmodconfig and an allyesconfig (build only for both).
[1] https://lore.kernel.org/linux-trace-kernel/20240222211442.634192653@goodmis.org/
Link: https://lore.kernel.org/linux-trace-kernel/20240516133454.681ba6a0@rorschach.local.home
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Christian König <christian.koenig@amd.com> for the amdgpu parts.
Acked-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> #for
Acked-by: Rafael J. Wysocki <rafael@kernel.org> # for thermal
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Darrick J. Wong <djwong@kernel.org> # xfs
Tested-by: Guenter Roeck <linux@roeck-us.net>
Simon Wunderlich says:
====================
This cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- prefer kfree_rcu() over call_rcu() with free-only callbacks,
by Dmitry Antipov
- bypass empty buckets in batadv_purge_orig_ref(), by Eric Dumazet
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
genetlink.h is a shell of what used to be a combined uAPI
and kernel header over a decade ago. It has fewer than
10 lines of code. Merge it into net/genetlink.h.
In some ways it'd be better to keep the combined header
under linux/ but it would make looking through git history
harder.
Acked-by: Sven Eckelmann <sven@narfation.org>
Link: https://lore.kernel.org/r/20240329175710.291749-4-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the MTU of one of an attached interface becomes too small to transmit
the local translation table then it must be resized to fit inside all
fragments (when enabled) or a single packet.
But if the MTU becomes too low to transmit even the header + the VLAN
specific part then the resizing of the local TT will never succeed. This
can for example happen when the usable space is 110 bytes and 11 VLANs are
on top of batman-adv. In this case, at least 116 byte would be needed.
There will just be an endless spam of
batman_adv: batadv0: Forced to purge local tt entries to fit new maximum fragment MTU (110)
in the log but the function will never finish. Problem here is that the
timeout will be halved all the time and will then stagnate at 0 and
therefore never be able to reduce the table even more.
There are other scenarios possible with a similar result. The number of
BATADV_TT_CLIENT_NOPURGE entries in the local TT can for example be too
high to fit inside a packet. Such a scenario can therefore happen also with
only a single VLAN + 7 non-purgable addresses - requiring at least 120
bytes.
While this should be handled proactively when:
* interface with too low MTU is added
* VLAN is added
* non-purgeable local mac is added
* MTU of an attached interface is reduced
* fragmentation setting gets disabled (which most likely requires dropping
attached interfaces)
not all of these scenarios can be prevented because batman-adv is only
consuming events without the the possibility to prevent these actions
(non-purgable MAC address added, MTU of an attached interface is reduced).
It is therefore necessary to also make sure that the code is able to handle
also the situations when there were already incompatible system
configuration are present.
Cc: stable@vger.kernel.org
Fixes: a19d3d85e1 ("batman-adv: limit local translation table max size")
Reported-by: syzbot+a6a4b5bb3da165594cff@syzkaller.appspotmail.com
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Drop 'batadv_tt_local_entry_free_rcu()', 'batadv_tt_global_entry_free_rcu()'
and 'batadv_tt_orig_list_entry_free_rcu()' in favor of 'kfree_rcu()' in
'batadv_tt_local_entry_release()', 'batadv_tt_global_entry_release()' and
'batadv_tt_orig_list_entry_release()', respectively.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
This version will contain all the (major or even only minor) changes for
Linux 6.10.
The version number isn't a semantic version number with major and minor
information. It is just encoding the year of the expected publishing as
Linux -rc1 and the number of published versions this year (starting at 0).
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Simon Wunderlich says:
====================
This cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- Improve error handling in DAT and uevent generator,
by Markus Elfring (2 patches)
- Drop usage of export.h, by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The linux/export.h include was introduced in commit 9bcb94c861
("batman-adv: Introduce missing headers for genetlink restructure") to have
access to THIS_MODULE. But with commit 5b20755b77 ("init: move
THIS_MODULE from <linux/export.h> to <linux/init.h>"), it was moved and the
include for export.h is no longer needed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The kfree() function was called in up to three cases by
the batadv_throw_uevent() function during error handling
even if the passed variable contained a null pointer.
This issue was detected by using the Coccinelle software.
* Thus adjust jump targets.
* Reorder kfree() calls at the end.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The kfree() function was called in one case by
the batadv_dat_forward_data() function during error handling
even if the passed variable contained a null pointer.
This issue was detected by using the Coccinelle software.
* Thus return directly after a batadv_dat_select_candidates() call failed
at the beginning.
* Delete the label “out” which became unnecessary with this refactoring.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
This version will contain all the (major or even only minor) changes for
Linux 6.9.
The version number isn't a semantic version number with major and minor
information. It is just encoding the year of the expected publishing as
Linux -rc1 and the number of published versions this year (starting at 0).
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The batman-adv multicast tracker TVLV handler is registered for the
new batman-adv multicast packet type upon creating a batman-adv interface,
but not unregistered again upon the interface's deletion, leading to a
memory leak.
Fix this memory leak by calling the according TVLV handler unregister
routine for the multicast tracker TVLV upon batman-adv interface
deletion.
Fixes: 07afe1ba28 ("batman-adv: mcast: implement multicast packet reception and forwarding")
Reported-and-tested-by: syzbot+ebe64cc5950868e77358@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/000000000000beadc4060f0cbc23@google.com/
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
When a node which does not have the new batman-adv multicast packet type
capability vanishes then the according, global counter erroneously would
not be reduced in response on other nodes. Which in turn leads to the mesh
never switching back to sending with the new multicast packet type.
Fix this by reducing the according counter when such a node times out.
Fixes: 9003913322 ("batman-adv: mcast: implement multicast packet generation")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The commit 3cd39bc3b1 ("kernel.h: Move ARRAY_SIZE() to a separate
header") introduced a new header for the ARRAY_SIZE macro which was
previously exposed via linux/kernel.h.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The commit 39ced19b9e ("lib/vsprintf: split out sprintf() and friends")
introduced a new header for the sprintf related functions which were
previously exposed via linux/kernel.h.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Remove all zero MAC address entries (00:00:00:00:00:00) from a multicast
packet's tracker TVLV before transmitting it and update all headers
accordingly. This way, instead of keeping the multicast packet at a
constant size throughout its journey through the mesh, it will become
more lightweight, smaller with every interested receiver on the way and
on each splitting intersection. Which can save some valuable bandwidth.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Implement the preparation of a batman-adv multicast packet and use this
under certain conditions.
For one thing this implements the capability to push a complete
batman-adv multicast packet header, including a tracker TVLV with all
originator destinations that have signaled interest in it, onto a given
ethernet frame with an IP multicast packet inside.
For another checks are implemented to determine if encapsulating a
multicast packet in this new batman-adv multicast packet type and using
it is feasible. Those checks are:
1) Have all nodes signaled that they are capable of handling the new
batman-adv multicast packet type?
2) Do all active hard interfaces of all nodes, including us, have an MTU
of at least 1280 bytes?
3) Does a complete multicast packet header with all its destination
addresses fit onto the given multicast packet / ethernet frame and
does not exceed 1280 bytes?
If all checks passed then the new batman-adv multicast packet type will
be used for transmission and distribution. Otherwise we fall back to one or
more batman-adv unicast packet transmissions, if possible. Or if not
possible we will fall back to classic flooding through a batman-adv
broadcast packet.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Implement functionality to receive and forward a new TVLV capable
multicast packet type.
The new batman-adv multicast packet type allows to contain several
originator destination addresses within a TVLV. Routers on the way will
potentially split the batman-adv multicast packet and adjust its tracker
TVLV contents.
Routing decisions are still based on the selected BATMAN IV or BATMAN V
routing algorithm. So this new batman-adv multicast packet type retains
the same loop-free properties.
Also a new OGM multicast TVLV flag is introduced to signal to other
nodes that we are capable of handling a batman-adv multicast packet and
multicast tracker TVLV. And that all of our hard interfaces have an MTU
of at least 1280 bytes (IPv6 minimum MTU), as a simple solution for now
to avoid MTU issues while forwarding.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
This version will contain all the (major or even only minor) changes for
Linux 6.8.
The version number isn't a semantic version number with major and minor
information. It is just encoding the year of the expected publishing as
Linux -rc1 and the number of published versions this year (starting at 0).
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
This code was only used in the past for the sysfs interface. But since
this was replace with netlink, it was never executed. The function pointer
was only checked to figure out whether the limit 255 (B.A.T.M.A.N. IV) or
2**32-1 (B.A.T.M.A.N. V) should be used as limit.
So instead of keeping the function pointer, just store the limits directly
in struct batadv_algo_gw_ops.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The batadv_netlink_notify_*() functions are not used by any other source
file. Just keep them local to netlink.c to get informed by the compiler
when they are not used anymore.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
This function is no longer used since the sysfs support was removed from
batman-adv.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
When a client roamed back to a node before it got time to destroy the
pending local entry (i.e. within the same originator interval) the old
global one is directly removed from hash table and left as such.
But because this entry had an extra reference taken at lookup (i.e using
batadv_tt_global_hash_find) there is no way its memory will be reclaimed
at any time causing the following memory leak:
unreferenced object 0xffff0000073c8000 (size 18560):
comm "softirq", pid 0, jiffies 4294907738 (age 228.644s)
hex dump (first 32 bytes):
06 31 ac 12 c7 7a 05 00 01 00 00 00 00 00 00 00 .1...z..........
2c ad be 08 00 80 ff ff 6c b6 be 08 00 80 ff ff ,.......l.......
backtrace:
[<00000000ee6e0ffa>] kmem_cache_alloc+0x1b4/0x300
[<000000000ff2fdbc>] batadv_tt_global_add+0x700/0xe20
[<00000000443897c7>] _batadv_tt_update_changes+0x21c/0x790
[<000000005dd90463>] batadv_tt_update_changes+0x3c/0x110
[<00000000a2d7fc57>] batadv_tt_tvlv_unicast_handler_v1+0xafc/0xe10
[<0000000011793f2a>] batadv_tvlv_containers_process+0x168/0x2b0
[<00000000b7cbe2ef>] batadv_recv_unicast_tvlv+0xec/0x1f4
[<0000000042aef1d8>] batadv_batman_skb_recv+0x25c/0x3a0
[<00000000bbd8b0a2>] __netif_receive_skb_core.isra.0+0x7a8/0xe90
[<000000004033d428>] __netif_receive_skb_one_core+0x64/0x74
[<000000000f39a009>] __netif_receive_skb+0x48/0xe0
[<00000000f2cd8888>] process_backlog+0x174/0x344
[<00000000507d6564>] __napi_poll+0x58/0x1f4
[<00000000b64ef9eb>] net_rx_action+0x504/0x590
[<00000000056fa5e4>] _stext+0x1b8/0x418
[<00000000878879d6>] run_ksoftirqd+0x74/0xa4
unreferenced object 0xffff00000bae1a80 (size 56):
comm "softirq", pid 0, jiffies 4294910888 (age 216.092s)
hex dump (first 32 bytes):
00 78 b1 0b 00 00 ff ff 0d 50 00 00 00 00 00 00 .x.......P......
00 00 00 00 00 00 00 00 50 c8 3c 07 00 00 ff ff ........P.<.....
backtrace:
[<00000000ee6e0ffa>] kmem_cache_alloc+0x1b4/0x300
[<00000000d9aaa49e>] batadv_tt_global_add+0x53c/0xe20
[<00000000443897c7>] _batadv_tt_update_changes+0x21c/0x790
[<000000005dd90463>] batadv_tt_update_changes+0x3c/0x110
[<00000000a2d7fc57>] batadv_tt_tvlv_unicast_handler_v1+0xafc/0xe10
[<0000000011793f2a>] batadv_tvlv_containers_process+0x168/0x2b0
[<00000000b7cbe2ef>] batadv_recv_unicast_tvlv+0xec/0x1f4
[<0000000042aef1d8>] batadv_batman_skb_recv+0x25c/0x3a0
[<00000000bbd8b0a2>] __netif_receive_skb_core.isra.0+0x7a8/0xe90
[<000000004033d428>] __netif_receive_skb_one_core+0x64/0x74
[<000000000f39a009>] __netif_receive_skb+0x48/0xe0
[<00000000f2cd8888>] process_backlog+0x174/0x344
[<00000000507d6564>] __napi_poll+0x58/0x1f4
[<00000000b64ef9eb>] net_rx_action+0x504/0x590
[<00000000056fa5e4>] _stext+0x1b8/0x418
[<00000000878879d6>] run_ksoftirqd+0x74/0xa4
Releasing the extra reference from batadv_tt_global_hash_find even at
roam back when batadv_tt_global_free is called fixes this memory leak.
Cc: stable@vger.kernel.org
Fixes: 068ee6e204 ("batman-adv: roaming handling mechanism redesign")
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by; Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
If the MTU of the soft/mesh interface was already reduced (enough), it is
not necessary to print a warning about a hard interface not having a MTU to
transport ethernet payloads of 1500 bytes.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The header linux/if_ether.h already defines a constant for the minimum MTU.
So simply use it instead of having a magic constant in the code.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Since commit 335fbe0f5d ("batman-adv: tvlv - convert tt query packet to use tvlv unicast packets")
batadv_recv_tt_query() is not used.
And commit 122edaa059 ("batman-adv: tvlv - convert roaming adv packet to use tvlv unicast packets")
left behind batadv_recv_roam_adv().
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
This version will contain all the (major or even only minor) changes for
Linux 6.6.
The version number isn't a semantic version number with major and minor
information. It is just encoding the year of the expected publishing as
Linux -rc1 and the number of published versions this year (starting at 0).
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
If the user set an MTU value, it usually means that there are special
requirements for the MTU. But if an interface gots activated, the MTU was
always recalculated and then the user set value was overwritten.
The only reason why this user set value has to be overwritten, is when the
MTU has to be decreased because batman-adv is not able to transfer packets
with the user specified size.
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Cc: stable@vger.kernel.org
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
