[ Upstream commit 0d68b55887 ]
Fix dp mode valid issue to avoid abnormal display of limit state.
After DP passes link training, it can express the lane count of the
current link status is good. Calculate the maximum bandwidth supported
by DP using the current lane count.
The color format will select the best one based on the bandwidth
requirements of the current timing mode. If the current timing mode
uses RGB and meets the DP link bandwidth requirements, RGB will be used.
If the timing mode uses RGB but does not meet the DP link bandwidthi
requirements, it will continue to check whether YUV422 meets
the DP link bandwidth.
FEC overhead is approximately 2.4% from DP 1.4a spec 2.2.1.4.2.
The down-spread amplitude shall either be disabled (0.0%) or up
to 0.5% from 1.4a 3.5.2.6. Add up to approximately 3% total overhead.
Because rate is already divided by 10,
mode->clock does not need to be multiplied by 10.
Fixes: f70ac097a2 ("drm/mediatek: Add MT8195 Embedded DisplayPort driver")
Signed-off-by: Liankun Yang <liankun.yang@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20241025083036.8829-3-liankun.yang@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 924d66011f ]
The PHY portion of the mediatek hdmi driver was originally part of
the driver it self and later split out into drivers/phy, which a
'select' to keep the prior behavior.
However, this leads to build failures when the PHY driver cannot
be built:
WARNING: unmet direct dependencies detected for PHY_MTK_HDMI
Depends on [n]: (ARCH_MEDIATEK || COMPILE_TEST [=y]) && COMMON_CLK [=y] && OF [=y] && REGULATOR [=n]
Selected by [m]:
- DRM_MEDIATEK_HDMI [=m] && HAS_IOMEM [=y] && DRM [=m] && DRM_MEDIATEK [=m]
ERROR: modpost: "devm_regulator_register" [drivers/phy/mediatek/phy-mtk-hdmi-drv.ko] undefined!
ERROR: modpost: "rdev_get_drvdata" [drivers/phy/mediatek/phy-mtk-hdmi-drv.ko] undefined!
The best option here is to just not select the phy driver and leave that
up to the defconfig. Do the same for the other PHY and memory drivers
selected here as well for consistency.
Fixes: a481bf2f0c ("drm/mediatek: Separate mtk_hdmi_phy to an independent module")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20241218085837.2670434-1-arnd@kernel.org/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe30bae552 ]
In mtk_crtc_ddp_config(), mtk_crtc will use some configuration flags to
generate instructions to cmdq_handle, such as:
state->pending_config
mtk_crtc->pending_planes
plane_state->pending.config
mtk_crtc->pending_async_planes
plane_state->pending.async_config
These configuration flags may be set to false when a GCE IRQ comes calling
ddp_cmdq_cb(). This may result in missing prepare instructions,
especially if mtk_crtc_update_config() with the flase need_vblank (no need
to wait for vblank) cases.
Therefore, the mtk_crtc->config_updating flag is set at the beginning of
mtk_crtc_update_config() to ensure that these configuration flags won't be
changed when the mtk_crtc_ddp_config() is preparing instructions.
But somehow the ddp_cmdq_cb() didn't use the mtk_crtc->config_updating
flag to prevent those pending config flags from being cleared.
To avoid missing the configuration when generating the config instruction,
the config_updating flag should be added into ddp_cmdq_cb() and be
protected with spin_lock.
Fixes: 7f82d9c438 ("drm/mediatek: Clear pending flag when cmdq packet is done")
Signed-off-by: Jason-JH.Lin <jason-jh.lin@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Reviewed-by: Fei Shao <fshao@chromium.org>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20240827-drm-fixup-0819-v3-1-4761005211ec@mediatek.com/
Link: https://patchwork.kernel.org/project/dri-devel/patch/20240827-drm-fixup-0819-v3-2-4761005211ec@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31c0fbf67c ]
The formula of Coverage alpha blending is:
dst.a = dst.a * (0xff - src.a * SCA / 0xff) / 0xff
+ src.a * SCA / 0xff
dst.a: destination alpha
src.a: pixel alpha
SCA : plane alpha
When SCA = 0xff, the formula becomes:
dst.a = dst.a * (0xff - src.a) + src.a
This patch is to set the destination alpha (background) to 0xff:
- When dst.a = 0 (before), dst.a = src.a
- When dst.a = 0xff (after) , dst.a = 0xff * (0xff - src.a) + src.a
According to the fomula above:
- When src.a = 0 , dst.a = 0
- When src.a = 0xff, dst.a = 0xff
This two cases are just still correct. But when src.a is
between 0 and 0xff, the difference starts to appear
Fixes: 616443ca57 ("drm/mediatek: Move cmdq_reg info from struct mtk_ddp_comp to sub driver private data")
Signed-off-by: Hsiao Chien Sung <shawn.sung@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20240620-igt-v3-5-a9d62d2e2c7e@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c38896ca63 ]
Based on grepping through the source code this driver appears to be
missing a call to drm_atomic_helper_shutdown() at system shutdown
time. Among other things, this means that if a panel is in use that it
won't be cleanly powered off at system shutdown time.
The fact that we should call drm_atomic_helper_shutdown() in the case
of OS shutdown/restart comes straight out of the kernel doc "driver
instance overview" in drm_drv.c.
This driver users the component model and shutdown happens in the base
driver. The "drvdata" for this driver will always be valid if
shutdown() is called and as of commit 2a07396828
("drm/atomic-helper: drm_atomic_helper_shutdown(NULL) should be a
noop") we don't need to confirm that "drm" is non-NULL.
Suggested-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Fei Shao <fshao@chromium.org>
Tested-by: Fei Shao <fshao@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240611102744.v2.1.I2b014f90afc4729b6ecc7b5ddd1f6dedcea4625b@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c958e86e9c ]
It's possible that mtk_crtc->event is NULL in
mtk_drm_crtc_finish_page_flip().
pending_needs_vblank value is set by mtk_crtc->event, but in
mtk_drm_crtc_atomic_flush(), it's is not guarded by the same
lock in mtk_drm_finish_page_flip(), thus a race condition happens.
Consider the following case:
CPU1 CPU2
step 1:
mtk_drm_crtc_atomic_begin()
mtk_crtc->event is not null,
step 1:
mtk_drm_crtc_atomic_flush:
mtk_drm_crtc_update_config(
!!mtk_crtc->event)
step 2:
mtk_crtc_ddp_irq ->
mtk_drm_finish_page_flip:
lock
mtk_crtc->event set to null,
pending_needs_vblank set to false
unlock
pending_needs_vblank set to true,
step 2:
mtk_crtc_ddp_irq ->
mtk_drm_finish_page_flip called again,
pending_needs_vblank is still true
//null pointer
Instead of guarding the entire mtk_drm_crtc_atomic_flush(), it's more
efficient to just check if mtk_crtc->event is null before use.
Fixes: 119f517362 ("drm/mediatek: Add DRM Driver for Mediatek SoC MT8173.")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20240223212404.3709690-1-hsinyi@chromium.org/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fae6f81550 ]
The register bits definitions for RGB666 formats are wrong in multiple
ways: first, in the DSI_PS_SEL bits region, the Packed 18-bits RGB666
format is selected with bit 1, while the Loosely Packed one is bit 2,
and second - the definition name "LOOSELY_PS_18BIT_RGB666" is wrong
because the loosely packed format is 24 bits instead!
Either way, functions mtk_dsi_ps_control_vact() and mtk_dsi_ps_control()
do not even agree on the DSI_PS_SEL bit to set in DSI_PSCTRL: one sets
loosely packed (24) on RGB666, the other sets packed (18), and the other
way around for RGB666_PACKED.
Fixing this entire stack of issues is done in one go:
- Use the correct bit for the Loosely Packed RGB666 definition
- Rename LOOSELY_PS_18BIT_RGB666 to LOOSELY_PS_24BIT_RGB666
- Change ps_bpp_mode in mtk_dsi_ps_control_vact() to set:
- Loosely Packed, 24-bits for MIPI_DSI_FMT_RGB666
- Packed, 18-bits for MIPI_DSI_FMT_RGB666_PACKED
Fixes: 2e54c14e31 ("drm/mediatek: Add DSI sub driver")
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20240215085316.56835-3-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8048dd0b0 ]
The mtk_dp driver registers a phy device which is handled by the
phy_mtk_dp driver and assumes that the phy probe will complete
synchronously, proceeding to make use of functionality exposed by that
driver right away. This assumption however is false when the phy driver
is built as a module, causing the mtk_dp driver to fail probe in this
case.
Add the phy_mtk_dp module as a pre-dependency to the mtk_dp module to
ensure the phy module has been loaded before the dp, so that the phy
probe happens synchrounously and the mtk_dp driver can probe
successfully even with the phy driver built as a module.
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Fixes: f70ac097a2 ("drm/mediatek: Add MT8195 Embedded DisplayPort driver")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Guillaume Ranquet <granquet@baylibre.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20231121142938.460846-1-nfraprado@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5855d422a6 ]
Due to the initial confusion about MIPI_DSI_MODE_EOT_PACKET, properly
renamed to MIPI_DSI_MODE_NO_EOT_PACKET, reflecting its actual meaning,
both the DSI_TXRX_CON register setting for bit (HSTX_)DIS_EOT and the
later calculation for horizontal sync-active (HSA), back (HBP) and
front (HFP) porches got incorrect due to the logic being inverted.
This means that a number of settings were wrong because....:
- DSI_TXRX_CON register setting: bit (HSTX_)DIS_EOT should be
set in order to disable the End of Transmission packet;
- Horizontal Sync and Back/Front porches: The delta used to
calculate all of HSA, HBP and HFP should account for the
additional EOT packet.
Before this change...
- Bit (HSTX_)DIS_EOT was being set when EOT packet was enabled;
- For HSA/HBP/HFP delta... all three were wrong, as words were
added when EOT disabled, instead of when EOT packet enabled!
Invert the logic around flag MIPI_DSI_MODE_NO_EOT_PACKET in the
MediaTek DSI driver to fix the aforementioned issues.
Fixes: 8b2b99fd79 ("drm/mediatek: dsi: Fine tune the line time caused by EOTp")
Fixes: c87d1c4b5b ("drm/mediatek: dsi: Use symbolized register definition")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Tested-by: Michael Walle <mwalle@kernel.org>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230523104234.7849-1-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53412dc290 ]
The difference between drm_atomic_helper_commit_tail() and
drm_atomic_helper_commit_tail_rpm() is
drm_atomic_helper_commit_tail() will commit plane first and
then enable crtc, drm_atomic_helper_commit_tail_rpm() will
enable crtc first and then commit plane.
Before mediatek-drm enables crtc, the power and clk required
by OVL have not been turned on, so the commit plane cannot be
committed before crtc is enabled. That means OVL layer should
not be enabled before crtc is enabled.
Therefore, the atomic_commit_tail of mediatek-drm is hooked with
drm_atomic_helper_commit_tail_rpm().
Another reason is that the plane_state of drm_atomic_state is not
synchronized with the plane_state stored in mtk_crtc during crtc enablng,
so just set all planes to disabled.
Fixes: 119f517362 ("drm/mediatek: Add DRM Driver for Mediatek SoC MT8173.")
Signed-off-by: Jason-JH.Lin <jason-jh.lin@mediatek.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20230809125722.24112-3-jason-jh.lin@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The MediaTek DRM driver implements GEM PRIME vmap by fetching the
sg_table for the object, iterating through the pages, and then
vmapping them. In essence, unlike the GEM DMA helpers which vmap
when the object is first created or imported, the MediaTek version
does it on request.
Unfortunately, the code never correctly frees the sg_table contents.
This results in a kernel memory leak. On a Hayato device with a text
console on the internal display, this results in the system running
out of memory in a few days from all the console screen cursor updates.
Add sg_free_table() to correctly free the contents of the sg_table. This
was missing despite explicitly required by mtk_gem_prime_get_sg_table().
Also move the "out" shortcut label to after the kfree() call for the
sg_table. Having sg_free_table() together with kfree() makes more sense.
The shortcut is only used when the object already has a kernel address,
in which case the pointer is NULL and kfree() does nothing. Hence this
change causes no functional change.
Fixes: 3df64d7b0a ("drm/mediatek: Implement gem prime vmap/vunmap function")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20231004083226.1940055-1-wenst@chromium.org/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Mediatek DRM Next for Linux 6.6
1. Small mtk-dpi cleanups
2. DisplayPort: support eDP and aux-bus
3. Fix uninitialized symbol
4. Do not check for 0 return after calling platform_get_irq()
5. Convert to platform remove callback returning void
6. Fix coverity issues
7. Fix potential memory leak if vmap() fail
8. Fix void-pointer-to-enum-cast warning
9. Rid W=1 warnings from GPU
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230813152726.14802-1-chunkuang.hu@kernel.org
1. Fix build warning message in mtk_disp_ovl_adaptor.c
>> drivers/gpu/drm/mediatek/mtk_disp_ovl_adaptor.c:415:10:
warning: cast to smaller integer type 'enum mtk_ovl_adaptor_comp_type'
from 'const void *' [-Wvoid-pointer-to-enum-cast]
type = (enum mtk_ovl_adaptor_comp_type)of_id->data;
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1 warning generated.
2. Also fix the same warning message in mtk_drm_drv.c
>> drivers/gpu/drm/mediatek/mtk_drm_drv.c:832:15:
warning: cast to smaller integer type 'enum mtk_ddp_comp_type'
from 'const void *' [-Wvoid-pointer-to-enum-cast]
comp_type = (enum mtk_ddp_comp_type)of_id->data;
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1 warning generated.
Signed-off-by: Jason-JH.Lin <jason-jh.lin@mediatek.com>
Fixes: 453c336463 ("drm/mediatek: Add ovl_adaptor support for MT8195")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202305042054.ZtWME9OU-lkp@intel.com/
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230621075421.1982-1-jason-jh.lin@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert the mediatek drm drivers from always returning zero in
the remove callback to the void returning variant.
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jyri Sarha <jyri.sarha@iki.fi>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230801110239.831099-8-u.kleine-koenig@pengutronix.de/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
