commit 614a19b89c upstream.
There is a scenario when resuming from some power saving states
with no_console_suspend where console output can be generated
before the 8250_bcm7271 driver gets the opportunity to restore
the baud_mux_clk frequency. Since the baud_mux_clk is at its
default frequency at this time the output can be garbled until
the driver gets the opportunity to resume.
Since this is only an issue with console use of the serial port
during that window and the console isn't likely to use baud
rates that require alternate baud_mux_clk frequencies, allow the
driver to select the default_mux_rate if it is accurate enough.
Fixes: 41a469482d ("serial: 8250: Add new 8250-core based Broadcom STB driver")
Cc: stable@vger.kernel.org
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240424222559.1844045-1-opendmb@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70d7f1427a upstream.
The current implementation uses either gsm0_receive() or gsm1_receive()
depending on whether the user configured the mux in basic or advanced
option mode. Both functions share some state values over the same logical
elements of the frame. However, both frame types differ in their nature.
gsm0_receive() uses non-transparency framing, whereas gsm1_receive() uses
transparency mechanism. Switching between both modes leaves the receive
function in an undefined state when done during frame reception.
Fix this by splitting both states. Add gsm0_receive_state_check_and_fix()
and gsm1_receive_state_check_and_fix() to ensure that gsm->state is reset
after a change of gsm->receive.
Note that gsm->state is only accessed in:
- gsm0_receive()
- gsm1_receive()
- gsm_error()
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20240424054842.7741-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47388e807f upstream.
Assuming the following:
- side A configures the n_gsm in basic option mode
- side B sends the header of a basic option mode frame with data length 1
- side A switches to advanced option mode
- side B sends 2 data bytes which exceeds gsm->len
Reason: gsm->len is not used in advanced option mode.
- side A switches to basic option mode
- side B keeps sending until gsm0_receive() writes past gsm->buf
Reason: Neither gsm->state nor gsm->len have been reset after
reconfiguration.
Fix this by changing gsm->count to gsm->len comparison from equal to less
than. Also add upper limit checks against the constant MAX_MRU in
gsm0_receive() and gsm1_receive() to harden against memory corruption of
gsm->len and gsm->mru.
All other checks remain as we still need to limit the data according to the
user configuration and actual payload size.
Reported-by: j51569436@gmail.com
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218708
Tested-by: j51569436@gmail.com
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20240424054842.7741-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 54c4ec5f8c ]
The uart_handle_cts_change() function in serial_core expects the caller
to hold uport->lock. For example, I have seen the below kernel splat,
when the Bluetooth driver is loaded on an i.MX28 board.
[ 85.119255] ------------[ cut here ]------------
[ 85.124413] WARNING: CPU: 0 PID: 27 at /drivers/tty/serial/serial_core.c:3453 uart_handle_cts_change+0xb4/0xec
[ 85.134694] Modules linked in: hci_uart bluetooth ecdh_generic ecc wlcore_sdio configfs
[ 85.143314] CPU: 0 PID: 27 Comm: kworker/u3:0 Not tainted 6.6.3-00021-gd62a2f068f92 #1
[ 85.151396] Hardware name: Freescale MXS (Device Tree)
[ 85.156679] Workqueue: hci0 hci_power_on [bluetooth]
(...)
[ 85.191765] uart_handle_cts_change from mxs_auart_irq_handle+0x380/0x3f4
[ 85.198787] mxs_auart_irq_handle from __handle_irq_event_percpu+0x88/0x210
(...)
Cc: stable@vger.kernel.org
Fixes: 4d90bb147e ("serial: core: Document and assert lock requirements for irq helpers")
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Emil Kronborg <emil.kronborg@protonmail.com>
Link: https://lore.kernel.org/r/20240320121530.11348-1-emil.kronborg@protonmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit dbf4ab8218 upstream.
The SC16IS7XX IC supports a burst mode to access the FIFOs where the
initial register address is sent ($00), followed by all the FIFO data
without having to resend the register address each time. In this mode, the
IC doesn't increment the register address for each R/W byte.
The regmap_raw_read() and regmap_raw_write() are functions which can
perform IO over multiple registers. They are currently used to read/write
from/to the FIFO, and although they operate correctly in this burst mode on
the SPI bus, they would corrupt the regmap cache if it was not disabled
manually. The reason is that when the R/W size is more than 1 byte, these
functions assume that the register address is incremented and handle the
cache accordingly.
Convert FIFO R/W functions to use the regmap _noinc_ versions in order to
remove the manual cache control which was a workaround when using the
_raw_ versions. FIFO registers are properly declared as volatile so
cache will not be used/updated for FIFO accesses.
Fixes: dfeae619d7 ("serial: sc16is7xx")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231211171353.2901416-6-hugo@hugovil.com
Cc: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: GONG, Ruiqi <gongruiqi1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 672448ccf9 upstream.
When about to transmit the function imx_uart_start_tx is called and in
some RS485 configurations this function will call imx_uart_stop_rx. The
problem is that imx_uart_stop_rx will enable loopback in order to
release the RS485 bus, but when loopback is enabled transmitted data
will just be looped to RX.
This patch fixes the above problem by not enabling loopback when about
to transmit.
This driver now works well when used for RS485 half duplex master
configurations.
Fixes: 79d0224f6b ("tty: serial: imx: Handle RS485 DE signal active high")
Cc: stable <stable@kernel.org>
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Tested-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Link: https://lore.kernel.org/r/20240221115304.509811-1-rickaran@axis.com
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 74cb7e0355 upstream.
If the remote uart device is not connected or not enabled after booting
up, the CTS line is high by default. At this time, if we enable the flow
control when opening the device(for example, using “stty -F /dev/ttyLP4
crtscts” command), there will be a pending idle preamble(first writing 0
and then writing 1 to UARTCTRL_TE will queue an idle preamble) that
cannot be sent out, resulting in the uart port fail to close(waiting for
TX empty), so the user space stty will have to wait for a long time or
forever.
This is an LPUART IP bug(idle preamble has higher priority than CTS),
here add a workaround patch to enable TX CTS after enabling UARTCTRL_TE,
so that the idle preamble does not get stuck due to CTS is deasserted.
Fixes: 380c966c09 ("tty: serial: fsl_lpuart: add 32-bit register interface support")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://lore.kernel.org/r/20240305015706.1050769-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 801410b26a ]
During the handoff from earlycon to the real console driver, we have
two separate drivers operating on the same device concurrently. In the
case of the 8250 driver these concurrent accesses cause problems due
to the driver's use of banked registers, controlled by LCR.DLAB. It is
possible for the setup(), config_port(), pm() and set_mctrl() callbacks
to set DLAB, which can cause the earlycon code that intends to access
TX to instead access DLL, leading to missed output and corruption on
the serial line due to unintended modifications to the baud rate.
In particular, for setup() we have:
univ8250_console_setup()
-> serial8250_console_setup()
-> uart_set_options()
-> serial8250_set_termios()
-> serial8250_do_set_termios()
-> serial8250_do_set_divisor()
For config_port() we have:
serial8250_config_port()
-> autoconfig()
For pm() we have:
serial8250_pm()
-> serial8250_do_pm()
-> serial8250_set_sleep()
For set_mctrl() we have (for some devices):
serial8250_set_mctrl()
-> omap8250_set_mctrl()
-> __omap8250_set_mctrl()
To avoid such problems, let's make it so that the console is locked
during pre-registration calls to these callbacks, which will prevent
the earlycon driver from running concurrently.
Remove the partial solution to this problem in the 8250 driver
that locked the console only during autoconfig_irq(), as this would
result in a deadlock with the new approach. The console continues
to be locked during autoconfig_irq() because it can only be called
through uart_configure_port().
Although this patch introduces more locking than strictly necessary
(and in particular it also locks during the call to rs485_config()
which is not affected by this issue as far as I can tell), it follows
the principle that it is the responsibility of the generic console
code to manage the earlycon handoff by ensuring that earlycon and real
console driver code cannot run concurrently, and not the individual
drivers.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Link: https://linux-review.googlesource.com/id/I7cf8124dcebf8618e6b2ee543fa5b25532de55d8
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240304214350.501253-1-pcc@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f42b142ea ]
After upgrading from 5.16 to 6.1, our board with a MAX14830 started
producing lots of garbage data over UART. Bisection pointed out commit
285e76fc04 as the culprit. That patch tried to replace hand-written
code which I added in 2b4bac48c1 ("serial: max310x: Use batched reads
when reasonably safe") with the generic regmap infrastructure for
batched operations.
Unfortunately, the `regmap_raw_read` and `regmap_raw_write` which were
used are actually functions which perform IO over *multiple* registers.
That's not what is needed for accessing these Tx/Rx FIFOs; the
appropriate functions are the `_noinc_` versions, not the `_raw_` ones.
Fix this regression by using `regmap_noinc_read()` and
`regmap_noinc_write()` along with the necessary `regmap_config` setup;
with this patch in place, our board communicates happily again. Since
our board uses SPI for talking to this chip, the I2C part is completely
untested.
Fixes: 285e76fc04 ("serial: max310x: use regmap methods for SPI batch operations")
Cc: stable@vger.kernel.org
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Link: https://lore.kernel.org/r/79db8e82aadb0e174bc82b9996423c3503c8fb37.1680732084.git.jan.kundrat@cesnet.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3883ab5e9 ]
SPI can only use 5 address bits, since one bit is reserved for
specifying R/W and 2 bits are used to specify the UART port.
To access registers that have addresses past 0x1F, an extended
register space can be enabled by writing to the GlobalCommand
register (address 0x1F).
I2C uses 8 address bits. The R/W bit is placed in the slave
address, and so is the UART port. Because of this, registers
that have addresses higher than 0x1F can be accessed normally.
To access the RevID register, on SPI, 0xCE must be written to
the 0x1F address to enable the extended register space, after
which the RevID register is accessible at address 0x5. 0xCD
must be written to the 0x1F address to disable the extended
register space.
On I2C, the RevID register is accessible at address 0x25.
Create an interface config struct, and add a method for
toggling the extended register space and a member for the RevId
register address. Implement these for SPI.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Link: https://lore.kernel.org/r/20220605144659.4169853-4-demonsingur@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 3f42b142ea ("serial: max310x: fix IO data corruption in batched operations")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ef281daf0 ]
The driver currently does manual register manipulation in
multiple places to talk to a specific UART port.
In order to talk to a specific UART port over SPI, the bits U1
and U0 of the register address can be set, as explained in the
Command byte configuration section of the datasheet.
Make this more elegant by creating regmaps for each UART port
and setting the read_flag_mask and write_flag_mask
accordingly.
All communcations regarding global registers are done on UART
port 0, so replace the global regmap entirely with the port 0
regmap.
Also, remove the 0x1f masks from reg_writeable(), reg_volatile()
and reg_precious() methods, since setting the U1 and U0 bits of
the register address happens inside the regmap core now.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Link: https://lore.kernel.org/r/20220605144659.4169853-3-demonsingur@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: b35f8dbbce ("serial: max310x: prevent infinite while() loop in port startup")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84f2faa785 ]
Serial core handles serial_rs485 sanitization.
When em485 init fails, there are two possible paths of entry:
1) uart_rs485_config (init path) that fully clears port->rs485 on
error.
2) ioctl path with a pre-existing, valid port->rs485 unto which the
kernel falls back on error and port->rs485 should therefore be
kept untouched. The temporary rs485 struct is not returned to
userspace in case of error so its flag don't matter.
...Thus SER_RS485_ENABLED clearing on error can/should be dropped.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-37-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c2a5f471c ]
The UART supports an auto-RTS mode in which the RTS pin is automatically
activated during transmission. So mark this mode as being supported even
if RTS is not controlled by the driver but the UART.
Also the serial core expects now at least one of both modes rts-on-send or
rts-after-send to be supported. This is since during sanitization
unsupported flags are deleted from a RS485 configuration set by userspace.
However if the configuration ends up with both flags unset, the core prints
a warning since it considers such a configuration invalid (see
uart_sanitize_serial_rs485()).
Cc: <stable@vger.kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240103061818.564-8-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0f25b8992 ]
The capability CAP_CHECKPOINT_RESTORE was introduced to allow non-root
users to checkpoint and restore processes as non-root with CRIU.
This change extends CAP_CHECKPOINT_RESTORE to enable the CRIU option
'--shell-job' as non-root. CRIU's man-page describes the '--shell-job'
option like this:
Allow one to dump shell jobs. This implies the restored task will
inherit session and process group ID from the criu itself. This option
also allows to migrate a single external tty connection, to migrate
applications like top.
TIOCSLCKTRMIOS can only be done if the process has CAP_SYS_ADMIN and
this change extends it to CAP_SYS_ADMIN or CAP_CHECKPOINT_RESTORE.
With this change it is possible to checkpoint and restore processes
which have a tty connection as non-root if CAP_CHECKPOINT_RESTORE is
set.
Acked-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Adrian Reber <areber@redhat.com>
Acked-by: Andrei Vagin <avagin@gmail.com>
Link: https://lore.kernel.org/r/20231208143656.1019-1-areber@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66aad7d8d3 ]
In ACM support for sending breaks to devices is optional.
If a device says that it doenot support sending breaks,
the host must respect that.
Given the number of optional features providing tty operations
for each combination is not practical and errors need to be
returned dynamically if unsupported features are requested.
In case a device does not support break, we want the tty layer
to treat that like it treats drivers that statically cannot
support sending a break. It ignores the inability and does nothing.
This patch uses EOPNOTSUPP to indicate that.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 9e98966c7b ("tty: rework break handling")
Link: https://lore.kernel.org/r/20231207132639.18250-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66619686d1 ]
If the driver sets TTY_DRIVER_HARDWARE_BREAK, we leave ops->break_ctl()
to the driver and return from send_break(). But we do it using a local
variable and keep the code flowing through the end of the function.
Instead, do 'return' immediately with the ops->break_ctl()'s return
value.
This way, we don't have to stuff the 'else' branch of the 'if' with the
software break handling. And we can re-indent the function too.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230919085156.1578-14-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 66aad7d8d3 ("usb: cdc-acm: return correct error code on unsupported break")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78d60dae9a ]
When using the serial port as RS485 port, the tx statemachine is used to
control the RTS pin to drive the RS485 transceiver TX_EN pin. When the
TTY port is closed in the middle of a transmission (for instance during
userland application crash), imx_uart_shutdown disables the interface
and disables the Transmission Complete interrupt. afer that,
imx_uart_stop_tx bails on an incomplete transmission, to be retriggered
by the TC interrupt. This interrupt is disabled and therefore the tx
statemachine never transitions out of SEND. The statemachine is in
deadlock now, and the TX_EN remains low, making the interface useless.
imx_uart_stop_tx now checks for incomplete transmission AND whether TC
interrupts are enabled before bailing to be retriggered. This makes sure
the state machine handling is reached, and is properly set to
WAIT_AFTER_SEND.
Fixes: cb1a609236 ("serial: imx: implement rts delaying for rs485")
Signed-off-by: Paul Geurts <paul_geurts@live.nl>
Tested-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Tested-by: Eberhard Stoll <eberhard.stoll@gmx.de>
Link: https://lore.kernel.org/r/AM0PR09MB26758F651BC1B742EB45775995B8A@AM0PR09MB2675.eurprd09.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad90d0358b ]
Returning an error code from .remove() makes the driver core emit the
little helpful error message:
remove callback returned a non-zero value. This will be ignored.
and then remove the device anyhow. So all resources that were not freed
are leaked in this case. Skipping serial8250_unregister_port() has the
potential to keep enough of the UART around to trigger a use-after-free.
So replace the error return (and with it the little helpful error
message) by a more useful error message and continue to cleanup.
Fixes: e3f0c638f4 ("serial: 8250: omap: Fix unpaired pm_runtime_put_sync() in omap8250_remove()")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20231110152927.70601-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6d710b769c upstream.
The original comment is confusing because it implies that variants other
than the SC16IS762 supports other SPI modes beside SPI_MODE_0.
Extract from datasheet:
The SC16IS762 differs from the SC16IS752 in that it supports SPI clock
speeds up to 15 Mbit/s instead of the 4 Mbit/s supported by the
SC16IS752... In all other aspects, the SC16IS762 is functionally and
electrically the same as the SC16IS752.
The same is also true of the SC16IS760 variant versus the SC16IS740 and
SC16IS750 variants.
For all variants, only SPI mode 0 is supported.
Change comment and abort probing if the specified SPI mode is not
SPI_MODE_0.
Fixes: 2c837a8a8f ("sc16is7xx: spi interface is added")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c45eaa813 upstream.
There are register accesses in the function imx_uart_rs485_config(). The
clock must be enabled for these accesses. This was ensured by calling it
via the function uart_rs485_config() in the probe() function within the
range where the clock is enabled. With the commit 7c7f9bc986 ("serial:
Deassert Transmit Enable on probe in driver-specific way") it was removed
from the probe() function and is now only called through the function
uart_add_one_port() which is located at the end of the probe() function.
But the clock is already switched off in this area. To ensure that the
clock is enabled during register access, move the disabling of the clock
to the very end of the probe() function. To avoid leaking enabled clocks
on error also add an error path for exiting with disabling the clock.
Fixes: 7c7f9bc986 ("serial: Deassert Transmit Enable on probe in driver-specific way")
Cc: stable <stable@kernel.org>
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/20231226113647.39376-1-cniedermaier@dh-electronics.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08ce9a1b72 upstream.
This device has a silicon bug that makes it report a timeout interrupt
but no data in the FIFO.
The datasheet states the following in the errata section 18.1.4:
"If the host reads the receive FIFO at the same time as a
time-out interrupt condition happens, the host might read 0xCC
(time-out) in the Interrupt Indication Register (IIR), but bit 0
of the Line Status Register (LSR) is not set (means there is no
data in the receive FIFO)."
The errata description seems to indicate it concerns only polled mode of
operation when reading bit 0 of the LSR register. However, tests have
shown and NXP has confirmed that the RXLVL register also yields 0 when
the bug is triggered, and hence the IRQ driven implementation in this
driver is equally affected.
This bug has hit us on production units and when it does, sc16is7xx_irq()
would spin forever because sc16is7xx_port_irq() keeps seeing an
interrupt in the IIR register that is not cleared because the driver
does not call into sc16is7xx_handle_rx() unless the RXLVL register
reports at least one byte in the FIFO.
Fix this by always reading one byte from the FIFO when this condition
is detected in order to clear the interrupt. This approach was
confirmed to be correct by NXP through their support channels.
Tested by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Daniel Mack <daniel@zonque.org>
Co-Developed-by: Maxim Popov <maxim.snafu@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231123072818.1394539-1-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5b68061983 ]
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211224142917.6966-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 2a1d728f20 ("tty: serial: meson: fix hard LOCKUP on crtscts mode")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ef5dd8ec88 upstream.
The xencons_connect_backend() function allocates a local interdomain
event channel with xenbus_alloc_evtchn(), then calls
bind_interdomain_evtchn_to_irq_lateeoi() to bind to that port# on the
*remote* domain.
That doesn't work very well:
(qemu) device_add xen-console,id=con1,chardev=pty0
[ 44.323872] xenconsole console-1: 2 xenbus_dev_probe on device/console/1
[ 44.323995] xenconsole: probe of console-1 failed with error -2
Fix it to use bind_evtchn_to_irq_lateeoi(), which does the right thing
by just binding that *local* event channel to an irq. The backend will
do the interdomain binding.
This didn't affect the primary console because the setup for that is
special — the toolstack allocates the guest event channel and the guest
discovers it with HVMOP_get_param.
Fixes: fe415186b4 ("xen/console: harden hvc_xen against event channel storms")
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231020161529.355083-2-dwmw2@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a30badfd7c upstream.
On unplug of a Xen console, xencons_disconnect_backend() unconditionally
calls free_irq() via unbind_from_irqhandler(), causing a warning of
freeing an already-free IRQ:
(qemu) device_del con1
[ 32.050919] ------------[ cut here ]------------
[ 32.050942] Trying to free already-free IRQ 33
[ 32.050990] WARNING: CPU: 0 PID: 51 at kernel/irq/manage.c:1895 __free_irq+0x1d4/0x330
It should be using evtchn_put() to tear down the event channel binding,
and let the Linux IRQ side of it be handled by notifier_del_irq() through
the HVC code.
On which topic... xencons_disconnect_backend() should call hvc_remove()
*first*, rather than tearing down the event channel and grant mapping
while they are in use. And then the IRQ is guaranteed to be freed by
the time it's torn down by evtchn_put().
Since evtchn_put() also closes the actual event channel, avoid calling
xenbus_free_evtchn() except in the failure path where the IRQ was not
successfully set up.
However, calling hvc_remove() at the start of xencons_disconnect_backend()
still isn't early enough. An unplug request is indicated by the backend
setting its state to XenbusStateClosing, which triggers a notification
to xencons_backend_changed(), which... does nothing except set its own
frontend state directly to XenbusStateClosed without *actually* tearing
down the HVC device or, you know, making sure it isn't actively in use.
So the backend sees the guest frontend set its state to XenbusStateClosed
and stops servicing the interrupt... and the guest spins for ever in the
domU_write_console() function waiting for the ring to drain.
Fix that one by calling hvc_remove() from xencons_backend_changed() before
signalling to the backend that it's OK to proceed with the removal.
Tested with 'dd if=/dev/zero of=/dev/hvc1' while telling Qemu to remove
the console device.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231020161529.355083-4-dwmw2@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Doug Berger
Daniel Starke
Daniel Thompson
Emil Kronborg
Finn Thain
Thadeu Lima de Souza Cascardo
Hugo Villeneuve
Rickard x Andersson
Nicolas Pitre
Sherry Sun
Peter Collingbourne
Andy Shevchenko
Tudor Ambarus
Jiri Slaby (SUSE)
Jan Kundrát
Cosmin Tanislav
Ilpo Järvinen
Lino Sanfilippo
Adrian Reber
Christoph Niedermaier
Oliver Neukum
Paul Geurts
Uwe Kleine-König
Ronald Wahl
Daniel Mack
Arnd Bergmann
Pavel Krasavin
Lad Prabhakar
David Woodhouse