[ Upstream commit e16ad6c799 ]
The reference manual for the i.MX8MN states the clock rate in
MMC mode is 1/2 of the input clock, therefore to properly run
at HS400 rates, the input clock must be 400MHz to operate at
200MHz. Currently the clock is set to 200MHz which is half the
rate it should be, so the throughput is half of what it should be
for HS400 operation.
Fixes: 36ca3c8ccb ("arm64: dts: imx: Add Beacon i.MX8M Nano development kit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f83f69097a ]
The reference manual for the i.MX8MM states the clock rate in
MMC mode is 1/2 of the input clock, therefore to properly run
at HS400 rates, the input clock must be 400MHz to operate at
200MHz. Currently the clock is set to 200MHz which is half the
rate it should be, so the throughput is half of what it should be
for HS400 operation.
Fixes: 593816fa2f ("arm64: dts: imx: Add Beacon i.MX8m-Mini development kit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fdc8ad019a ]
Pinmux registers ends at 0x000f42ac (including). Thus, the size argument
of the pinctrl-single node has to be 0x2b0. Fix it.
This will fix the following error:
pinctrl-single f4000.pinctrl: mux offset out of range: 0x2ac (0x2ac)
Fixes: 29075cc09f ("arm64: dts: ti: Introduce AM62P5 family of SoCs")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20250618065239.1904953-1-mwalle@kernel.org
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 945e48a39c ]
For the ICSSG PHYs to operate correctly, a 25 MHz reference clock must
be supplied on CLKOUT0. Previously, our bootloader configured this
clock, which is why the PRU Ethernet ports appeared to work, but the
change never made it into the device tree.
Add clock properties to make EXT_REFCLK1.CLKOUT0 output a 25MHz clock.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Fixes: 87adfd1ab0 ("arm64: dts: ti: am642-phyboard-electra: Add PRU-ICSSG nodes")
Link: https://lore.kernel.org/r/20250521053339.1751844-1-w.egorov@phytec.de
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 53b6445ad0 upstream.
Hardware CS has a very slow rise time of about 6us,
causing transmission errors when CS does not reach
high between transaction.
It looks like it's not driven actively when transitioning
from low to high but switched to input, so only the CPU
pull-up pulls it high, slowly. Transitions from high to low
are fast. On the oscilloscope, CS looks like an irregular sawtooth
pattern like this:
_____
^ / |
^ /| / |
/| / | / |
/ | / | / |
___/ |___/ |_____/ |___
With cs-gpios we have a CS rise time of about 20ns, as it should be,
and CS looks rectangular.
This fixes the data errors when running a flashcp loop against a
m25p40 spi flash.
With the Rockchip 6.1 kernel we see the same slow rise time, but
for some reason CS is always high for long enough to reach a solid
high.
The RK3399 and RK3588 SoCs use the same SPI driver, so we also
checked our "Puma" (RK3399) and "Tiger" (RK3588) boards.
They do not have this problem. Hardware CS rise time is good.
Fixes: c484cf93f6 ("arm64: dts: rockchip: add PX30-µQ7 (Ringneck) SoM with Haikou baseboard")
Cc: stable@vger.kernel.org
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Jakob Unterwurzacher <jakob.unterwurzacher@cherry.de>
Link: https://lore.kernel.org/r/20250627131715.1074308-1-jakob.unterwurzacher@cherry.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fbe94be09f upstream.
LDO5 regulator is used to power the i.MX8MM NVCC_SD2 I/O supply, that is
used for the SD2 card interface and also for some GPIOs.
When the SD card interface is not enabled the regulator subsystem could
turn off this supply, since it is not used anywhere else, however this
will also remove the power to some other GPIOs, for example one I/O that
is used to power the ethernet phy, leading to a non working ethernet
interface.
[ 31.820515] On-module +V3.3_1.8_SD (LDO5): disabling
[ 31.821761] PMIC_USDHC_VSELECT: disabling
[ 32.764949] fec 30be0000.ethernet end0: Link is Down
Fix this keeping the LDO5 supply always on.
Cc: stable@vger.kernel.org
Fixes: 6a57f224f7 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Fixes: f5aab0438e ("regulator: pca9450: Fix enable register for LDO5")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 720fd1cbc0 upstream.
Watchdog doesn't work on NXP ls1046ardb board because in commit
7c8ffc5555cb("arm64: dts: layerscape: remove big-endian for mmc nodes"),
it intended to remove the big-endian from mmc node, but the big-endian of
watchdog node is also removed by accident. So, add watchdog big-endian
property back.
In addition, add compatible string fsl,ls1046a-wdt, which allow big-endian
property.
Fixes: 7c8ffc5555 ("arm64: dts: layerscape: remove big-endian for mmc nodes")
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d7cc532df9 ]
Currently, the onboard Cypress CYUSB3304 USB hub is not defined in
the device tree, and hub reset pin is provided as vcc5v0_host
regulator to usb phy. This causes instability issues, as a result
of improper reset duration.
The fixed regulator device requests the GPIO during probe in its
inactive state (except if regulator-boot-on property is set, in
which case it is requested in the active state). Considering gpio
is GPIO_ACTIVE_LOW for Puma, it means it’s driving it high. Then
the regulator gets enabled (because regulator-always-on property),
which drives it to its active state, meaning driving it low.
The Cypress CYUSB3304 USB hub actually requires the reset to be
asserted for at least 5 ms, which we cannot guarantee right now
since there's no delay in the current config, meaning the hub may
sometimes work or not. We could add delay as offered by
fixed-regulator but let's rather fix this by using the proper way
to model onboard USB hubs.
Define hub_2_0 and hub_3_0 nodes, as the onboard Cypress hub
consist of two 'logical' hubs, for USB2.0 and USB3.0.
Use the 'reset-gpios' property of hub to assign reset pin instead
of using regulator. Rename the vcc5v0_host regulator to
cy3304_reset to be more meaningful. Pin is configured to
output-high by default, which sets the hub in reset state
during pin controller initialization. This allows to avoid double
enumeration of devices in case the bootloader has setup the USB
hub before the kernel.
The vdd-supply and vdd2-supply properties in hub nodes are
added to provide correct dt-bindings, although power supplies are
always enabled based on HW design.
Fixes: 2c66fc34e9 ("arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM")
Cc: stable@vger.kernel.org # 6.6
Cc: stable@vger.kernel.org # Backport of the patch in this series fixing product ID in onboard_dev_id_table in drivers/usb/misc/onboard_usb_dev.c driver
Signed-off-by: Lukasz Czechowski <lukasz.czechowski@thaumatec.com>
Link: https://lore.kernel.org/r/20250425-onboard_usb_dev-v2-3-4a76a474a010@thaumatec.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd1c959f37 ]
Add missing "avdd-0v9-supply" and "avdd-1v8-supply" properties to the "hdmi"
node in the Pine64 RockPro64 board dtsi file. To achieve this, also add the
associated "vcca_0v9" regulator that produces the 0.9 V supply, [1][2] which
hasn't been defined previously in the board dtsi file.
This also eliminates the following warnings from the kernel log:
dwhdmi-rockchip ff940000.hdmi: supply avdd-0v9 not found, using dummy regulator
dwhdmi-rockchip ff940000.hdmi: supply avdd-1v8 not found, using dummy regulator
There are no functional changes to the way board works with these additions,
because the "vcc1v8_dvp" and "vcca_0v9" regulators are always enabled, [1][2]
but these additions improve the accuracy of hardware description.
These changes apply to the both supported hardware revisions of the Pine64
RockPro64, i.e. to the production-run revisions 2.0 and 2.1. [1][2]
[1] https://files.pine64.org/doc/rockpro64/rockpro64_v21-SCH.pdf
[2] https://files.pine64.org/doc/rockpro64/rockpro64_v20-SCH.pdf
Fixes: e4f3fb4909 ("arm64: dts: rockchip: add initial dts support for Rockpro64")
Cc: stable@vger.kernel.org
Suggested-by: Diederik de Haas <didi.debian@cknow.org>
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Tested-by: Diederik de Haas <didi.debian@cknow.org>
Link: https://lore.kernel.org/r/df3d7e8fe74ed5e727e085b18c395260537bb5ac.1740941097.git.dsimic@manjaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03f2b8eed7 ]
The firmware configures the TSENS controller with a maximum temperature of
120°C. When reaching that temperature, the hardware automatically triggers
a reset of the entire platform. Some of the thermal zones in x1e80100.dtsi
use a critical trip point of 125°C. It's impossible to reach those.
It's preferable to shut down the system cleanly before reaching the
hardware trip point. Make the critical temperature trip points consistent
by setting all of them to 115°C and apply a consistent hysteresis.
The ACPI tables also specify 115°C as critical shutdown temperature.
Cc: stable@vger.kernel.org
Fixes: 4e915987ff ("arm64: dts: qcom: x1e80100: Enable tsens and thermal zone nodes")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250219-x1e80100-thermal-fixes-v1-2-d110e44ac3f9@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit febd8c6ab5 ]
The u2phy0_host port is the part of the USB PHY0 (namely the
HOST0_DP/DM lanes) which routes directly to the USB2.0 HOST
controller[1]. The other lanes of the PHY are routed to the USB3.0 OTG
controller (dwc3), which we do use.
The HOST0_DP/DM lanes aren't routed on RK3399 Puma so let's simply
disable the USB2.0 controllers.
USB3 OTG has been known to be unstable on RK3399 Puma Haikou for a
while, one of the recurring issues being that only USB2 is detected and
not USB3 in host mode. Reading the justification above and seeing that
we are keeping u2phy0_host in the Haikou carrierboard DTS probably may
have bothered you since it should be changed to u2phy0_otg. The issue is
that if it's switched to that, USB OTG on Haikou is entirely broken. I
have checked the routing in the Gerber file, the lanes are going to the
expected ball pins (that is, NOT HOST0_DP/DM).
u2phy0_host is for sure the wrong part of the PHY to use, but it's the
only one that works at the moment for that board so keep it until we
figure out what exactly is broken.
No intended functional change.
[1] https://rockchip.fr/Rockchip%20RK3399%20TRM%20V1.3%20Part2.pdf
Chapter 2 USB2.0 PHY
Fixes: 2c66fc34e9 ("arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM")
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Lukasz Czechowski <lukasz.czechowski@thaumatec.com>
Link: https://lore.kernel.org/r/20250425-onboard_usb_dev-v2-5-4a76a474a010@thaumatec.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a706a593cb ]
As described in the radxa_rock_3c_v1400_schematic.pdf, the SPI Flash's
VCC connector is connected to VCCIO_FLASH and according to the
that same schematic, that belongs to the VCC_1V8 power source.
This fixes the following warning:
spi-nor spi4.0: supply vcc not found, using dummy regulator
Fixes: ee219017dd ("arm64: dts: rockchip: Add Radxa ROCK 3C")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Link: https://lore.kernel.org/r/20250506195702.593044-1-pbrobinson@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d77e89b7b0 ]
Some of the regulators in the MT6357 PMIC dtsi have compatible set to
regulator-fixed, even though they don't serve any purpose: all those
regulators are handled as a whole by the mt6357-regulator driver. In
fact this is the only dtsi in this family of chips where this is the
case: mt6359 and mt6358 don't have any such compatibles.
A side-effect caused by this is that the DT kselftest, which is supposed
to identify nodes with compatibles that can be probed, but haven't,
shows these nodes as failures.
Remove the useless compatibles to move the dtsi in line with the others
in its family and fix the DT kselftest failures.
Fixes: 55749bb478 ("arm64: dts: mediatek: add mt6357 device-tree")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20250502-mt6357-regulator-fixed-compatibles-removal-v1-1-a582c16743fe@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a747c4dd2a ]
The HDMI bridge chip fails to generate an audio source due to the SAI5
master clock (MCLK) direction not being set to output. This prevents proper
clocking of the HDMI audio interface.
Add the `fsl,sai-mclk-direction-output` property to the SAI5 node to ensure
the MCLK is driven by the SoC, resolving the HDMI sound issue.
Fixes: 1d6880ceef ("arm64: dts: imx8mn-beacon: Add HDMI video with sound")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c716f80df ]
The HDMI bridge chip fails to generate an audio source due to the SAI5
master clock (MCLK) direction not being set to output. This prevents proper
clocking of the HDMI audio interface.
Add the `fsl,sai-mclk-direction-output` property to the SAI5 node to ensure
the MCLK is driven by the SoC, resolving the HDMI sound issue.
Fixes: 8ad7d14d99 ("arm64: dts: imx8mm-beacon: Add HDMI video with sound")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Adam Ford
Patrick Delaunay
Michael Walle
Wadim Egorov
André Apitzsch
Lijuan Gao
Will Deacon
Konrad Dybcio
Alexander Stein
Stephan Gerhold
Johan Hovold
Richard Zhu
Andy Yan
Jakob Unterwurzacher
Tim Harvey
Francesco Dolcini
Meng Li
Pengyu Luo
Geert Uytterhoeven
Luca Weiss
Krzysztof Kozlowski
Lukasz Czechowski
Janne Grunau
Dragan Simic
Julien Massot
Thuan Nguyen
Dmitry Baryshkov
Quentin Schulz
Prasanth Babu Mantena
Aaron Kling
Peter Robinson
Alexey Minnekhanov
Nícolas F. R. A. Prado