commit a7982a14b3 upstream.
Original logic only sets the return value but doesn't jump out of the
loop if the bus is kept active by a client. This is not expected. A
malicious or buggy i2c client can hang the kernel in this case and
should be avoided. This is observed during a long time test with a
PCA953x GPIO extender.
Fix it by changing the logic to not only sets the return value, but also
jumps out of the loop and return to the caller with -ETIMEDOUT.
Fixes: fbfab1ab06 ("i2c: qup: reorganization of driver code to remove polling for qup v1")
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Cc: <stable@vger.kernel.org> # v4.17+
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250616-qca-i2c-v1-1-2a8d37ee0a30@outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6aae87fe7f upstream.
Before each I2C transfer using DMA, the I2C buffer is DMA'pped to make
sure the memory buffer is DMA'able. This is handle in the function
`stm32_i2c_prep_dma_xfer()`.
If the transfer fails for any reason the I2C buffer must be unmap.
Use the dma_callback to factorize the code and fix this issue.
Note that the `stm32f7_i2c_dma_callback()` is now called in case of DMA
transfer success and error and that the `complete()` on the dma_complete
completion structure is done inconditionnally in case of transfer
success or error as well as the `dmaengine_terminate_async()`.
This is allowed as a `complete()` in case transfer error has no effect
as well as a `dmaengine_terminate_async()` on a transfer success.
Also fix the unneeded cast and remove not more needed variables.
Fixes: 7ecc8cfde5 ("i2c: i2c-stm32f7: Add DMA support")
Signed-off-by: Clément Le Goffic <clement.legoffic@foss.st.com>
Cc: <stable@vger.kernel.org> # v4.18+
Acked-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250704-i2c-upstream-v4-2-84a095a2c728@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2fe2b969d9 ]
Replaced pm_runtime_put() with pm_runtime_put_sync_suspend() to ensure
the runtime suspend is invoked immediately when unregistering a slave.
This prevents a race condition where suspend was skipped when
unregistering and registering slave in quick succession.
For example, consider the rapid sequence of
`delete_device -> new_device -> delete_device -> new_device`.
In this sequence, it is observed that the dw_i2c_plat_runtime_suspend()
might not be invoked after `delete_device` operation.
This is because after `delete_device` operation, when the
pm_runtime_put() is about to trigger suspend, the following `new_device`
operation might race and cancel the suspend.
If that happens, during the `new_device` operation,
dw_i2c_plat_runtime_resume() is skipped (since there was no suspend), which
means `i_dev->init()`, i.e. i2c_dw_init_slave(), is skipped.
Since i2c_dw_init_slave() is skipped, i2c_dw_configure_fifo_slave() is
skipped too, which leaves `DW_IC_INTR_MASK` unconfigured. If we inspect
the interrupt mask register using devmem, it will show as zero.
Example shell script to reproduce the issue:
```
#!/bin/sh
SLAVE_LADDR=0x1010
SLAVE_BUS=13
NEW_DEVICE=/sys/bus/i2c/devices/i2c-$SLAVE_BUS/new_device
DELETE_DEVICE=/sys/bus/i2c/devices/i2c-$SLAVE_BUS/delete_device
# Create initial device
echo slave-24c02 $SLAVE_LADDR > $NEW_DEVICE
sleep 2
# Rapid sequence of
# delete_device -> new_device -> delete_device -> new_device
echo $SLAVE_LADDR > $DELETE_DEVICE
echo slave-24c02 $SLAVE_LADDR > $NEW_DEVICE
echo $SLAVE_LADDR > $DELETE_DEVICE
echo slave-24c02 $SLAVE_LADDR > $NEW_DEVICE
# Using devmem to inspect IC_INTR_MASK will show as zero
```
Signed-off-by: Tan En De <ende.tan@starfivetech.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20250412023303.378600-1-ende.tan@starfivetech.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4f35233a6 ]
When the I2C QUP controller is used together with a DMA engine it needs
to vote for the interconnect path to the DRAM. Otherwise it may be
unable to access the memory quickly enough.
The requested peak bandwidth is dependent on the I2C core clock.
To avoid sending votes too often the bandwidth is always requested when
a DMA transfer starts, but dropped only on runtime suspend. Runtime
suspend should only happen if no transfer is active. After resumption we
can defer the next vote until the first DMA transfer actually happens.
The implementation is largely identical to the one introduced for
spi-qup in commit ecdaa94730 ("spi: qup: Vote for interconnect
bandwidth to DRAM") since both drivers represent the same hardware
block.
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20231128-i2c-qup-dvfs-v1-3-59a0e3039111@kernkonzept.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75caec0c2a ]
The fwnode.h is not supposed to be used by the drivers as it
has the definitions for the core parts for different device
property provider implementations. Drop it.
Note, that fwnode API for drivers is provided in property.h
which is included here.
Fixes: a076a860ac ("media: i2c: add I2C Address Translator (ATR) support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
[wsa: reworded subject]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 285df995f9 upstream.
On the GTA04A5 writing a reset command to the gyroscope causes IRQ
storms because NACK IRQs are enabled and therefore triggered but not
acked.
Sending a reset command to the gyroscope by
i2cset 1 0x69 0x14 0xb6
with an additional debug print in the ISR (not the thread) itself
causes
[ 363.353515] i2c i2c-1: ioctl, cmd=0x720, arg=0xbe801b00
[ 363.359039] omap_i2c 48072000.i2c: addr: 0x0069, len: 2, flags: 0x0, stop: 1
[ 363.366180] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x1110)
[ 363.371673] omap_i2c 48072000.i2c: IRQ (ISR = 0x0010)
[ 363.376892] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x0102)
[ 363.382263] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x0102)
[ 363.387664] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x0102)
repeating till infinity
[...]
(0x2 = NACK, 0x100 = Bus free, which is not enabled)
Apparently no other IRQ bit gets set, so this stalls.
Do not ignore enabled interrupts and make sure they are acked.
If the NACK IRQ is not needed, it should simply not enabled, but
according to the above log, caring about it is necessary unless
the Bus free IRQ is enabled and handled. The assumption that is
will always come with a ARDY IRQ, which was the idea behind
ignoring it, proves wrong.
It is true for simple reads from an unused address.
To still avoid the i2cdetect trouble which is the reason for
commit c770657bd2 ("i2c: omap: Fix standard mode false ACK readings"),
avoid doing much about NACK in omap_i2c_xfer_data() which is used
by both IRQ mode and polling mode, so also the false detection fix
is extended to polling usage and IRQ storms are avoided.
By changing this, the hardirq handler is not needed anymore to filter
stuff.
The mentioned gyro reset now just causes a -ETIMEDOUT instead of
hanging the system.
Fixes: c770657bd2 ("i2c: omap: Fix standard mode false ACK readings").
CC: stable@kernel.org
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Tested-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Aniket Limaye <a-limaye@ti.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250228140420.379498-1-andreas@kemnade.info
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71c49ee9bb upstream.
According to the chip manual, the I2C register access type of
Loongson-2K2000/LS7A is "B", so we can only access registers in byte
form (readb()/writeb()).
Although Loongson-2K0500/Loongson-2K1000 do not have similar
constraints, register accesses in byte form also behave correctly.
Also, in hardware, the frequency division registers are defined as two
separate registers (high 8-bit and low 8-bit), so we just access them
directly as bytes.
Fixes: 015e61f0bf ("i2c: ls2x: Add driver for Loongson-2K/LS7A I2C controller")
Co-developed-by: Hongliang Wang <wanghongliang@loongson.cn>
Signed-off-by: Hongliang Wang <wanghongliang@loongson.cn>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Cc: stable@vger.kernel.org # v6.3+
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250220125612.1910990-1-zhoubinbin@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bfd74cd1fb ]
When a 400KHz freq is used on this model of ELAN touchpad in Linux,
excessive smoothing (similar to when the touchpad's firmware detects
a noisy signal) is sometimes applied. As some devices' (e.g, Lenovo
V15 G4) ACPI tables specify a 400KHz frequency for this device and
some I2C busses (e.g, Designware I2C) default to a 400KHz freq,
force the speed to 100KHz as a workaround.
For future investigation: This problem may be related to the default
HCNT/LCNT values given by some busses' drivers, because they are not
specified in the aforementioned devices' ACPI tables, and because
the device works without issues on Windows at what is expected to be
a 400KHz frequency. The root cause of the issue is not known.
Signed-off-by: Randolph Ha <rha051117@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ceb8bf2cea ]
Commit cdd30ebb1b ("module: Convert symbol namespace to string
literal") only converted MODULE_IMPORT_NS() and EXPORT_SYMBOL_NS(),
leaving DEFAULT_SYMBOL_NAMESPACE as a macro expansion.
This commit converts DEFAULT_SYMBOL_NAMESPACE in the same way to avoid
annoyance for the default namespace as well.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stable-dep-of: 2505f87eb3 ("hwmon: (nct6775): Actually make use of the HWMON_NCT6775 symbol namespace")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cefc479cbb upstream.
i2c-atr catches the BUS_NOTIFY_DEL_DEVICE event on the bus and removes
the translation by calling i2c_atr_detach_client().
However, BUS_NOTIFY_DEL_DEVICE happens when the device is about to be
removed from this bus, i.e. before removal, and thus before calling
.remove() on the driver. If the driver happens to do any i2c
transactions in its remove(), they will fail.
Fix this by catching BUS_NOTIFY_REMOVED_DEVICE instead, thus removing
the translation only after the device is actually removed.
Fixes: a076a860ac ("media: i2c: add I2C Address Translator (ATR) support")
Cc: stable@vger.kernel.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Romain Gantois <romain.gantois@bootlin.com>
Tested-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6ad30f7890 ]
This backend requests a NACK from the controller driver when it detects
an error. If that request gets ignored from some reason, subsequent
accesses will wrongly be handled OK. To fix this, an error now changes
the state machine, so the backend will report NACK until a STOP
condition has been detected. This make the driver more robust against
controllers which will sadly apply the NACK not to the current byte but
the next one.
Fixes: a8335c64c5 ("i2c: add slave testunit driver")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 093f70c134 ]
When this controller is a target, the NACK handling had two issues.
First, the return value from the backend was not checked on the initial
WRITE_REQUESTED. So, the driver missed to send a NACK in this case.
Also, the NACK always arrives one byte late on the bus, even in the
WRITE_RECEIVED case. This seems to be a HW issue. We should then not
rely on the backend to correctly NACK the superfluous byte as well. Fix
both issues by introducing a flag which gets set whenever the backend
requests a NACK and keep sending it until we get a STOP condition.
Fixes: de20d1857d ("i2c: rcar: add slave support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca89f73394 ]
When misconfigured, the initial setup of the current mux channel can
fail, too. It must be checked as well.
Fixes: 50a5ba8769 ("i2c: mux: demux-pinctrl: add driver")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f8c4f5e9a ]
The reference count of the device incremented in device_initialize() is
not decremented when device_add() fails. Add a put_device() call before
returning from the function.
This bug was found by an experimental static analysis tool that I am
developing.
Fixes: 60f6859702 ("i2c: core: Setup i2c_adapter runtime-pm before calling device_add()")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 49e1f0fd0d upstream.
Running i2c-detect currently produces an output akin to:
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: 08 -- 0a -- 0c -- 0e --
10: 10 -- 12 -- 14 -- 16 -- UU 19 -- 1b -- 1d -- 1f
20: -- 21 -- 23 -- 25 -- 27 -- 29 -- 2b -- 2d -- 2f
30: -- -- -- -- -- -- -- -- 38 -- 3a -- 3c -- 3e --
40: 40 -- 42 -- 44 -- 46 -- 48 -- 4a -- 4c -- 4e --
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: 60 -- 62 -- 64 -- 66 -- 68 -- 6a -- 6c -- 6e --
70: 70 -- 72 -- 74 -- 76 --
This happens because for an i2c_msg with a len of 0 the driver will
mark the transmission of the message as a success once the START has
been sent, without waiting for the devices on the bus to respond with an
ACK/NAK. Since i2cdetect seems to run in a tight loop over all addresses
the NAK is treated as part of the next test for the next address.
Delete the fast path that marks a message as complete when idev->msg_len
is zero after sending a START/RESTART since this isn't a valid scenario.
CC: stable@vger.kernel.org
Fixes: 64a6f1c498 ("i2c: add support for microchip fpga i2c controllers")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20241218-outbid-encounter-b2e78b1cc707@spud
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e0cec36319 upstream.
Compatible string "fsl,imx7d-i2c" is not exited at i2c-imx driver
compatible string table, at the result, "fsl,imx21-i2c" will be
matched, but it will cause erratum ERR007805 not be applied in fact.
So Add "fsl,imx7d-i2c" compatible string in i2c-imx driver to apply
the erratum ERR007805(https://www.nxp.com/docs/en/errata/IMX7DS_3N09P.pdf).
"
ERR007805 I2C: When the I2C clock speed is configured for 400 kHz,
the SCL low period violates the I2C spec of 1.3 uS min
Description: When the I2C module is programmed to operate at the
maximum clock speed of 400 kHz (as defined by the I2C spec), the SCL
clock low period violates the I2C spec of 1.3 uS min. The user must
reduce the clock speed to obtain the SCL low time to meet the 1.3us
I2C minimum required. This behavior means the SoC is not compliant
to the I2C spec at 400kHz.
Workaround: To meet the clock low period requirement in fast speed
mode, SCL must be configured to 384KHz or less.
"
"fsl,imx7d-i2c" already is documented in binding doc. This erratum
fix has been included in imx6_i2c_hwdata and it is the same in all
I.MX6/7/8, so just reuse it.
Fixes: 39c025721d ("i2c: imx: Implement errata ERR007805 or e7805 bus frequency limit")
Cc: stable@vger.kernel.org # v5.18+
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Fixes: 39c025721d ("i2c: imx: Implement errata ERR007805 or e7805 bus frequency limit")
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20241218044238.143414-1-carlos.song@nxp.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de6b43798d upstream.
Currently, the RIIC driver may run the I2C bus faster than requested,
which may cause subtle failures. E.g. Biju reported a measured bus
speed of 450 kHz instead of the expected maximum of 400 kHz on RZ/G2L.
The initial calculation of the bus period uses DIV_ROUND_UP(), to make
sure the actual bus speed never becomes faster than the requested bus
speed. However, the subsequent division-by-two steps do not use
round-up, which may lead to a too-small period, hence a too-fast and
possible out-of-spec bus speed. E.g. on RZ/Five, requesting a bus speed
of 100 resp. 400 kHz will yield too-fast target bus speeds of 100806
resp. 403226 Hz instead of 97656 resp. 390625 Hz.
Fix this by using DIV_ROUND_UP() in the subsequent divisions, too.
Tested on RZ/A1H, RZ/A2M, and RZ/Five.
Fixes: d982d66514 ("i2c: riic: remove clock and frequency restrictions")
Reported-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: <stable@vger.kernel.org> # v4.15+
Link: https://lore.kernel.org/r/c59aea77998dfea1b4456c4b33b55ab216fcbf5e.1732284746.git.geert+renesas@glider.be
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7363f2d4c1 ]
Since commit f63b94be69 ("i2c: pnx: Fix potential deadlock warning
from del_timer_sync() call in isr") jiffies are stored in
i2c_pnx_algo_data.timeout, but wait_timeout and wait_reset are still
using it as milliseconds. Convert jiffies back to milliseconds to wait
for the expected amount of time.
Fixes: f63b94be69 ("i2c: pnx: Fix potential deadlock warning from del_timer_sync() call in isr")
Signed-off-by: Vladimir Riabchun <ferr.lambarginio@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48730a9d04 ]
Early return in i2cdev_ioctl_rdwr() failed to free the memory allocated
by the caller. Move freeing the memory to the function where it has been
allocated to prevent similar leaks in the future.
Fixes: 97ca843f6a ("i2c: dev: Check for I2C_FUNC_I2C before calling i2c_transfer")
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
[wsa: replaced '== NULL' with '!']
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
When the Tx FIFO is empty and the last command has no STOP bit
set, the master holds SCL low. If I2C_DYNAMIC_TAR_UPDATE is not
set, BIT(13) MST_ON_HOLD of IC_RAW_INTR_STAT is not enabled,
causing the __i2c_dw_disable() timeout. This is quite similar to
commit 2409205acd ("i2c: designware: fix __i2c_dw_disable() in
case master is holding SCL low"). Also check BIT(7)
MST_HOLD_TX_FIFO_EMPTY in IC_STATUS, which is available when
IC_STAT_FOR_CLK_STRETCH is set.
Fixes: 2409205acd ("i2c: designware: fix __i2c_dw_disable() in case master is holding SCL low")
Co-developed-by: Xiaowu Ding <xiaowu.ding@jaguarmicro.com>
Signed-off-by: Xiaowu Ding <xiaowu.ding@jaguarmicro.com>
Co-developed-by: Angus Chen <angus.chen@jaguarmicro.com>
Signed-off-by: Angus Chen <angus.chen@jaguarmicro.com>
Signed-off-by: Liu Peibao <loven.liu@jaguarmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
If dev_get_regmap() fails, it returns NULL pointer not ERR_PTR(),
replace IS_ERR() with NULL pointer check, and return -ENODEV.
Fixes: d0f8e97866 ("i2c: muxes: add support for tsd,mule-i2c multiplexer")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Pull i2c fix from Wolfram Sang:
- Fix potential deadlock during runtime suspend and resume (stm32f7)
* tag 'i2c-for-6.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: stm32f7: Do not prepare/unprepare clock during runtime suspend/resume
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
In case there is any sort of clock controller attached to this I2C bus
controller, for example Versaclock or even an AIC32x4 I2C codec, then
an I2C transfer triggered from the clock controller clk_ops .prepare
callback may trigger a deadlock on drivers/clk/clk.c prepare_lock mutex.
This is because the clock controller first grabs the prepare_lock mutex
and then performs the prepare operation, including its I2C access. The
I2C access resumes this I2C bus controller via .runtime_resume callback,
which calls clk_prepare_enable(), which attempts to grab the prepare_lock
mutex again and deadlocks.
Since the clock are already prepared since probe() and unprepared in
remove(), use simple clk_enable()/clk_disable() calls to enable and
disable the clock on runtime suspend and resume, to avoid hitting the
prepare_lock mutex.
Acked-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Fixes: 4e7bca6fc0 ("i2c: i2c-stm32f7: add PM Runtime support")
Cc: <stable@vger.kernel.org> # v5.0+
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Pull i2c fixes from Wolfram Sang:
- fix DesignWare driver ENABLE-ABORT sequence, ensuring ABORT can
always be sent when needed
- check for PCLK in the SynQuacer controller as an optional clock,
allowing ACPI to directly provide the clock rate
- KEBA driver Kconfig dependency fix
- fix XIIC driver power suspend sequence
* tag 'i2c-for-6.12-rc1-additional_fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: xiic: Fix pm_runtime_set_suspended() with runtime pm enabled
i2c: keba: I2C_KEBA should depend on KEBA_CP500
i2c: synquacer: Deal with optional PCLK correctly
i2c: designware: fix controller is holding SCL low while ENABLE bit is disabled
no_llseek had been defined to NULL two years ago, in commit 868941b144
("fs: remove no_llseek")
To quote that commit,
At -rc1 we'll need do a mechanical removal of no_llseek -
git grep -l -w no_llseek | grep -v porting.rst | while read i; do
sed -i '/\<no_llseek\>/d' $i
done
would do it.
Unfortunately, that hadn't been done. Linus, could you do that now, so
that we could finally put that thing to rest? All instances are of the
form
.llseek = no_llseek,
so it's obviously safe.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
