commit f914b52c37 upstream.
The following issue happens with a buggy module:
BUG: unable to handle page fault for address: ffffffffc05d0218
PGD 1bd66f067 P4D 1bd66f067 PUD 1bd671067 PMD 101808067 PTE 0
Oops: Oops: 0000 [#1] SMP KASAN PTI
Tainted: [O]=OOT_MODULE, [E]=UNSIGNED_MODULE
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
RIP: 0010:sized_strscpy+0x81/0x2f0
RSP: 0018:ffff88812d76fa08 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffffffffc0601010 RCX: dffffc0000000000
RDX: 0000000000000038 RSI: dffffc0000000000 RDI: ffff88812608da2d
RBP: 8080808080808080 R08: ffff88812608da2d R09: ffff88812608da68
R10: ffff88812608d82d R11: ffff88812608d810 R12: 0000000000000038
R13: ffff88812608da2d R14: ffffffffc05d0218 R15: fefefefefefefeff
FS: 00007fef552de740(0000) GS:ffff8884251c7000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffffffc05d0218 CR3: 00000001146f0000 CR4: 00000000000006f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
ftrace_mod_get_kallsym+0x1ac/0x590
update_iter_mod+0x239/0x5b0
s_next+0x5b/0xa0
seq_read_iter+0x8c9/0x1070
seq_read+0x249/0x3b0
proc_reg_read+0x1b0/0x280
vfs_read+0x17f/0x920
ksys_read+0xf3/0x1c0
do_syscall_64+0x5f/0x2e0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
The above issue may happen as follows:
(1) Add kprobe tracepoint;
(2) insmod test.ko;
(3) Module triggers ftrace disabled;
(4) rmmod test.ko;
(5) cat /proc/kallsyms; --> Will trigger UAF as test.ko already removed;
ftrace_mod_get_kallsym()
...
strscpy(module_name, mod_map->mod->name, MODULE_NAME_LEN);
...
The problem is when a module triggers an issue with ftrace and
sets ftrace_disable. The ftrace_disable is set when an anomaly is
discovered and to prevent any more damage, ftrace stops all text
modification. The issue that happened was that the ftrace_disable stops
more than just the text modification.
When a module is loaded, its init functions can also be traced. Because
kallsyms deletes the init functions after a module has loaded, ftrace
saves them when the module is loaded and function tracing is enabled. This
allows the output of the function trace to show the init function names
instead of just their raw memory addresses.
When a module is removed, ftrace_release_mod() is called, and if
ftrace_disable is set, it just returns without doing anything more. The
problem here is that it leaves the mod_list still around and if kallsyms
is called, it will call into this code and access the module memory that
has already been freed as it will return:
strscpy(module_name, mod_map->mod->name, MODULE_NAME_LEN);
Where the "mod" no longer exists and triggers a UAF bug.
Link: https://lore.kernel.org/all/20250523135452.626d8dcd@gandalf.local.home/
Cc: stable@vger.kernel.org
Fixes: aba4b5c22c ("ftrace: Save module init functions kallsyms symbols for tracing")
Link: https://lore.kernel.org/20250529111955.2349189-2-yebin@huaweicloud.com
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42ea22e754 upstream.
When the kernel contains a large number of functions that can be traced,
the loop in ftrace_graph_set_hash() may take a lot of time to execute.
This may trigger the softlockup watchdog.
Add cond_resched() within the loop to allow the kernel to remain
responsive even when processing a large number of functions.
This matches the cond_resched() that is used in other locations of the
code that iterates over all functions that can be traced.
Cc: stable@vger.kernel.org
Fixes: b9b0c831be ("ftrace: Convert graph filter to use hash tables")
Link: https://lore.kernel.org/tencent_3E06CE338692017B5809534B9C5C03DA7705@qq.com
Signed-off-by: zhoumin <teczm@foxmail.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38b1406194 upstream.
Function graph uses a subops and manager ops mechanism to attach to
ftrace. The manager ops connects to ftrace and the functions it connects
to is defined by a list of subops that it manages.
The function hash that defines what the above ops attaches to limits the
functions to attach if the hash has any content. If the hash is empty, it
means to trace all functions.
The creation of the manager ops hash is done by iterating over all the
subops hashes. If any of the subops hashes is empty, it means that the
manager ops hash must trace all functions as well.
The issue is in the creation of the manager ops. When a second subops is
attached, a new hash is created by starting it as NULL and adding the
subops one at a time. But the NULL ops is mistaken as an empty hash, and
once an empty hash is found, it stops the loop of subops and just enables
all functions.
# echo "f:myevent1 kernel_clone" >> /sys/kernel/tracing/dynamic_events
# cat /sys/kernel/tracing/enabled_functions
kernel_clone (1) tramp: 0xffffffffc0309000 (ftrace_graph_func+0x0/0x60) ->ftrace_graph_func+0x0/0x60
# echo "f:myevent2 schedule_timeout" >> /sys/kernel/tracing/dynamic_events
# cat /sys/kernel/tracing/enabled_functions
trace_initcall_start_cb (1) tramp: 0xffffffffc0309000 (ftrace_graph_func+0x0/0x60) ->ftrace_graph_func+0x0/0x60
run_init_process (1) tramp: 0xffffffffc0309000 (ftrace_graph_func+0x0/0x60) ->ftrace_graph_func+0x0/0x60
try_to_run_init_process (1) tramp: 0xffffffffc0309000 (ftrace_graph_func+0x0/0x60) ->ftrace_graph_func+0x0/0x60
x86_pmu_show_pmu_cap (1) tramp: 0xffffffffc0309000 (ftrace_graph_func+0x0/0x60) ->ftrace_graph_func+0x0/0x60
cleanup_rapl_pmus (1) tramp: 0xffffffffc0309000 (ftrace_graph_func+0x0/0x60) ->ftrace_graph_func+0x0/0x60
uncore_free_pcibus_map (1) tramp: 0xffffffffc0309000 (ftrace_graph_func+0x0/0x60) ->ftrace_graph_func+0x0/0x60
uncore_types_exit (1) tramp: 0xffffffffc0309000 (ftrace_graph_func+0x0/0x60) ->ftrace_graph_func+0x0/0x60
uncore_pci_exit.part.0 (1) tramp: 0xffffffffc0309000 (ftrace_graph_func+0x0/0x60) ->ftrace_graph_func+0x0/0x60
kvm_shutdown (1) tramp: 0xffffffffc0309000 (ftrace_graph_func+0x0/0x60) ->ftrace_graph_func+0x0/0x60
vmx_dump_msrs (1) tramp: 0xffffffffc0309000 (ftrace_graph_func+0x0/0x60) ->ftrace_graph_func+0x0/0x60
vmx_cleanup_l1d_flush (1) tramp: 0xffffffffc0309000 (ftrace_graph_func+0x0/0x60) ->ftrace_graph_func+0x0/0x60
[..]
Fix this by initializing the new hash to NULL and if the hash is NULL do
not treat it as an empty hash but instead allocate by copying the content
of the first sub ops. Then on subsequent iterations, the new hash will not
be NULL, but the content of the previous subops. If that first subops
attached to all functions, then new hash may assume that the manager ops
also needs to attach to all functions.
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Link: https://lore.kernel.org/20250220202055.060300046@goodmis.org
Fixes: 5fccc7552c ("ftrace: Add subops logic to allow one ops to manage many")
Reviewed-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 789a8cff8d upstream.
Commit c132be2c4f ("function_graph: Have the instances use their own
ftrace_ops for filtering"), function profiler (enabled via
function_profile_enabled) has been showing statistics for all functions,
ignoring set_ftrace_filter settings.
While tracers are instantiated, the function profiler is not. Therefore, it
should use the global set_ftrace_filter for consistency. This patch
modifies the function profiler to use the global filter, fixing the
filtering functionality.
Before (filtering not working):
```
root@localhost:~# echo 'vfs*' > /sys/kernel/tracing/set_ftrace_filter
root@localhost:~# echo 1 > /sys/kernel/tracing/function_profile_enabled
root@localhost:~# sleep 1
root@localhost:~# echo 0 > /sys/kernel/tracing/function_profile_enabled
root@localhost:~# head /sys/kernel/tracing/trace_stat/*
Function Hit Time Avg
s^2
-------- --- ---- ---
---
schedule 314 22290594 us 70989.15 us
40372231 us
x64_sys_call 1527 8762510 us 5738.382 us
3414354 us
schedule_hrtimeout_range 176 8665356 us 49234.98 us
405618876 us
__x64_sys_ppoll 324 5656635 us 17458.75 us
19203976 us
do_sys_poll 324 5653747 us 17449.83 us
19214945 us
schedule_timeout 67 5531396 us 82558.15 us
2136740827 us
__x64_sys_pselect6 12 3029540 us 252461.7 us
63296940171 us
do_pselect.constprop.0 12 3029532 us 252461.0 us
63296952931 us
```
After (filtering working):
```
root@localhost:~# echo 'vfs*' > /sys/kernel/tracing/set_ftrace_filter
root@localhost:~# echo 1 > /sys/kernel/tracing/function_profile_enabled
root@localhost:~# sleep 1
root@localhost:~# echo 0 > /sys/kernel/tracing/function_profile_enabled
root@localhost:~# head /sys/kernel/tracing/trace_stat/*
Function Hit Time Avg
s^2
-------- --- ---- ---
---
vfs_write 462 68476.43 us 148.217 us
25874.48 us
vfs_read 641 9611.356 us 14.994 us
28868.07 us
vfs_fstat 890 878.094 us 0.986 us
1.667 us
vfs_fstatat 227 757.176 us 3.335 us
18.928 us
vfs_statx 226 610.610 us 2.701 us
17.749 us
vfs_getattr_nosec 1187 460.919 us 0.388 us
0.326 us
vfs_statx_path 297 343.287 us 1.155 us
11.116 us
vfs_rename 6 291.575 us 48.595 us
9889.236 us
```
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/20250101190820.72534-1-enjuk@amazon.com
Fixes: c132be2c4f ("function_graph: Have the instances use their own ftrace_ops for filtering")
Signed-off-by: Kohei Enju <enjuk@amazon.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c54a1a06da upstream.
Since the new fgraph requires to initialize fgraph_ops.ops.func_hash before
calling register_ftrace_graph(), initialize it with default (tracing all
functions) parameter.
Cc: stable@vger.kernel.org
Fixes: 5fccc7552c ("ftrace: Add subops logic to allow one ops to manage many")
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
const qualify the struct ctl_table argument in the proc_handler function
signatures. This is a prerequisite to moving the static ctl_table
structs into .rodata data which will ensure that proc_handler function
pointers cannot be modified.
This patch has been generated by the following coccinelle script:
```
virtual patch
@r1@
identifier ctl, write, buffer, lenp, ppos;
identifier func !~ "appldata_(timer|interval)_handler|sched_(rt|rr)_handler|rds_tcp_skbuf_handler|proc_sctp_do_(hmac_alg|rto_min|rto_max|udp_port|alpha_beta|auth|probe_interval)";
@@
int func(
- struct ctl_table *ctl
+ const struct ctl_table *ctl
,int write, void *buffer, size_t *lenp, loff_t *ppos);
@r2@
identifier func, ctl, write, buffer, lenp, ppos;
@@
int func(
- struct ctl_table *ctl
+ const struct ctl_table *ctl
,int write, void *buffer, size_t *lenp, loff_t *ppos)
{ ... }
@r3@
identifier func;
@@
int func(
- struct ctl_table *
+ const struct ctl_table *
,int , void *, size_t *, loff_t *);
@r4@
identifier func, ctl;
@@
int func(
- struct ctl_table *ctl
+ const struct ctl_table *ctl
,int , void *, size_t *, loff_t *);
@r5@
identifier func, write, buffer, lenp, ppos;
@@
int func(
- struct ctl_table *
+ const struct ctl_table *
,int write, void *buffer, size_t *lenp, loff_t *ppos);
```
* Code formatting was adjusted in xfs_sysctl.c to comply with code
conventions. The xfs_stats_clear_proc_handler,
xfs_panic_mask_proc_handler and xfs_deprecated_dointvec_minmax where
adjusted.
* The ctl_table argument in proc_watchdog_common was const qualified.
This is called from a proc_handler itself and is calling back into
another proc_handler, making it necessary to change it as part of the
proc_handler migration.
Co-developed-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Co-developed-by: Joel Granados <j.granados@samsung.com>
Signed-off-by: Joel Granados <j.granados@samsung.com>
Pull MM updates from Andrew Morton:
- In the series "mm: Avoid possible overflows in dirty throttling" Jan
Kara addresses a couple of issues in the writeback throttling code.
These fixes are also targetted at -stable kernels.
- Ryusuke Konishi's series "nilfs2: fix potential issues related to
reserved inodes" does that. This should actually be in the
mm-nonmm-stable tree, along with the many other nilfs2 patches. My
bad.
- More folio conversions from Kefeng Wang in the series "mm: convert to
folio_alloc_mpol()"
- Kemeng Shi has sent some cleanups to the writeback code in the series
"Add helper functions to remove repeated code and improve readability
of cgroup writeback"
- Kairui Song has made the swap code a little smaller and a little
faster in the series "mm/swap: clean up and optimize swap cache
index".
- In the series "mm/memory: cleanly support zeropage in
vm_insert_page*(), vm_map_pages*() and vmf_insert_mixed()" David
Hildenbrand has reworked the rather sketchy handling of the use of
the zeropage in MAP_SHARED mappings. I don't see any runtime effects
here - more a cleanup/understandability/maintainablity thing.
- Dev Jain has improved selftests/mm/va_high_addr_switch.c's handling
of higher addresses, for aarch64. The (poorly named) series is
"Restructure va_high_addr_switch".
- The core TLB handling code gets some cleanups and possible slight
optimizations in Bang Li's series "Add update_mmu_tlb_range() to
simplify code".
- Jane Chu has improved the handling of our
fake-an-unrecoverable-memory-error testing feature MADV_HWPOISON in
the series "Enhance soft hwpoison handling and injection".
- Jeff Johnson has sent a billion patches everywhere to add
MODULE_DESCRIPTION() to everything. Some landed in this pull.
- In the series "mm: cleanup MIGRATE_SYNC_NO_COPY mode", Kefeng Wang
has simplified migration's use of hardware-offload memory copying.
- Yosry Ahmed performs more folio API conversions in his series "mm:
zswap: trivial folio conversions".
- In the series "large folios swap-in: handle refault cases first",
Chuanhua Han inches us forward in the handling of large pages in the
swap code. This is a cleanup and optimization, working toward the end
objective of full support of large folio swapin/out.
- In the series "mm,swap: cleanup VMA based swap readahead window
calculation", Huang Ying has contributed some cleanups and a possible
fixlet to his VMA based swap readahead code.
- In the series "add mTHP support for anonymous shmem" Baolin Wang has
taught anonymous shmem mappings to use multisize THP. By default this
is a no-op - users must opt in vis sysfs controls. Dramatic
improvements in pagefault latency are realized.
- David Hildenbrand has some cleanups to our remaining use of
page_mapcount() in the series "fs/proc: move page_mapcount() to
fs/proc/internal.h".
- David also has some highmem accounting cleanups in the series
"mm/highmem: don't track highmem pages manually".
- Build-time fixes and cleanups from John Hubbard in the series
"cleanups, fixes, and progress towards avoiding "make headers"".
- Cleanups and consolidation of the core pagemap handling from Barry
Song in the series "mm: introduce pmd|pte_needs_soft_dirty_wp helpers
and utilize them".
- Lance Yang's series "Reclaim lazyfree THP without splitting" has
reduced the latency of the reclaim of pmd-mapped THPs under fairly
common circumstances. A 10x speedup is seen in a microbenchmark.
It does this by punting to aother CPU but I guess that's a win unless
all CPUs are pegged.
- hugetlb_cgroup cleanups from Xiu Jianfeng in the series
"mm/hugetlb_cgroup: rework on cftypes".
- Miaohe Lin's series "Some cleanups for memory-failure" does just that
thing.
- Someone other than SeongJae has developed a DAMON feature in Honggyu
Kim's series "DAMON based tiered memory management for CXL memory".
This adds DAMON features which may be used to help determine the
efficiency of our placement of CXL/PCIe attached DRAM.
- DAMON user API centralization and simplificatio work in SeongJae
Park's series "mm/damon: introduce DAMON parameters online commit
function".
- In the series "mm: page_type, zsmalloc and page_mapcount_reset()"
David Hildenbrand does some maintenance work on zsmalloc - partially
modernizing its use of pageframe fields.
- Kefeng Wang provides more folio conversions in the series "mm: remove
page_maybe_dma_pinned() and page_mkclean()".
- More cleanup from David Hildenbrand, this time in the series
"mm/memory_hotplug: use PageOffline() instead of PageReserved() for
!ZONE_DEVICE". It "enlightens memory hotplug more about PageOffline()
pages" and permits the removal of some virtio-mem hacks.
- Barry Song's series "mm: clarify folio_add_new_anon_rmap() and
__folio_add_anon_rmap()" is a cleanup to the anon folio handling in
preparation for mTHP (multisize THP) swapin.
- Kefeng Wang's series "mm: improve clear and copy user folio"
implements more folio conversions, this time in the area of large
folio userspace copying.
- The series "Docs/mm/damon/maintaier-profile: document a mailing tool
and community meetup series" tells people how to get better involved
with other DAMON developers. From SeongJae Park.
- A large series ("kmsan: Enable on s390") from Ilya Leoshkevich does
that.
- David Hildenbrand sends along more cleanups, this time against the
migration code. The series is "mm/migrate: move NUMA hinting fault
folio isolation + checks under PTL".
- Jan Kara has found quite a lot of strangenesses and minor errors in
the readahead code. He addresses this in the series "mm: Fix various
readahead quirks".
- SeongJae Park's series "selftests/damon: test DAMOS tried regions and
{min,max}_nr_regions" adds features and addresses errors in DAMON's
self testing code.
- Gavin Shan has found a userspace-triggerable WARN in the pagecache
code. The series "mm/filemap: Limit page cache size to that supported
by xarray" addresses this. The series is marked cc:stable.
- Chengming Zhou's series "mm/ksm: cmp_and_merge_page() optimizations
and cleanup" cleans up and slightly optimizes KSM.
- Roman Gushchin has separated the memcg-v1 and memcg-v2 code - lots of
code motion. The series (which also makes the memcg-v1 code
Kconfigurable) are "mm: memcg: separate legacy cgroup v1 code and put
under config option" and "mm: memcg: put cgroup v1-specific memcg
data under CONFIG_MEMCG_V1"
- Dan Schatzberg's series "Add swappiness argument to memory.reclaim"
adds an additional feature to this cgroup-v2 control file.
- The series "Userspace controls soft-offline pages" from Jiaqi Yan
permits userspace to stop the kernel's automatic treatment of
excessive correctable memory errors. In order to permit userspace to
monitor and handle this situation.
- Kefeng Wang's series "mm: migrate: support poison recover from
migrate folio" teaches the kernel to appropriately handle migration
from poisoned source folios rather than simply panicing.
- SeongJae Park's series "Docs/damon: minor fixups and improvements"
does those things.
- In the series "mm/zsmalloc: change back to per-size_class lock"
Chengming Zhou improves zsmalloc's scalability and memory
utilization.
- Vivek Kasireddy's series "mm/gup: Introduce memfd_pin_folios() for
pinning memfd folios" makes the GUP code use FOLL_PIN rather than
bare refcount increments. So these paes can first be moved aside if
they reside in the movable zone or a CMA block.
- Andrii Nakryiko has added a binary ioctl()-based API to
/proc/pid/maps for much faster reading of vma information. The series
is "query VMAs from /proc/<pid>/maps".
- In the series "mm: introduce per-order mTHP split counters" Lance
Yang improves the kernel's presentation of developer information
related to multisize THP splitting.
- Michael Ellerman has developed the series "Reimplement huge pages
without hugepd on powerpc (8xx, e500, book3s/64)". This permits
userspace to use all available huge page sizes.
- In the series "revert unconditional slab and page allocator fault
injection calls" Vlastimil Babka removes a performance-affecting and
not very useful feature from slab fault injection.
* tag 'mm-stable-2024-07-21-14-50' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (411 commits)
mm/mglru: fix ineffective protection calculation
mm/zswap: fix a white space issue
mm/hugetlb: fix kernel NULL pointer dereference when migrating hugetlb folio
mm/hugetlb: fix possible recursive locking detected warning
mm/gup: clear the LRU flag of a page before adding to LRU batch
mm/numa_balancing: teach mpol_to_str about the balancing mode
mm: memcg1: convert charge move flags to unsigned long long
alloc_tag: fix page_ext_get/page_ext_put sequence during page splitting
lib: reuse page_ext_data() to obtain codetag_ref
lib: add missing newline character in the warning message
mm/mglru: fix overshooting shrinker memory
mm/mglru: fix div-by-zero in vmpressure_calc_level()
mm/kmemleak: replace strncpy() with strscpy()
mm, page_alloc: put should_fail_alloc_page() back behing CONFIG_FAIL_PAGE_ALLOC
mm, slab: put should_failslab() back behind CONFIG_SHOULD_FAILSLAB
mm: ignore data-race in __swap_writepage
hugetlbfs: ensure generic_hugetlb_get_unmapped_area() returns higher address than mmap_min_addr
mm: shmem: rename mTHP shmem counters
mm: swap_state: use folio_alloc_mpol() in __read_swap_cache_async()
mm/migrate: putback split folios when numa hint migration fails
...
Pull ftrace updates from Steven Rostedt:
"Rewrite of function graph tracer to allow multiple users
Up until now, the function graph tracer could only have a single user
attached to it. If another user tried to attach to the function graph
tracer while one was already attached, it would fail. Allowing
function graph tracer to have more than one user has been asked for
since 2009, but it required a rewrite to the logic to pull it off so
it never happened. Until now!
There's three systems that trace the return of a function. That is
kretprobes, function graph tracer, and BPF. kretprobes and function
graph tracing both do it similarly. The difference is that kretprobes
uses a shadow stack per callback and function graph tracer creates a
shadow stack for all tasks. The function graph tracer method makes it
possible to trace the return of all functions. As kretprobes now needs
that feature too, allowing it to use function graph tracer was needed.
BPF also wants to trace the return of many probes and its method
doesn't scale either. Having it use function graph tracer would
improve that.
By allowing function graph tracer to have multiple users allows both
kretprobes and BPF to use function graph tracer in these cases. This
will allow kretprobes code to be removed in the future as it's version
will no longer be needed.
Note, function graph tracer is only limited to 16 simultaneous users,
due to shadow stack size and allocated slots"
* tag 'ftrace-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace: (49 commits)
fgraph: Use str_plural() in test_graph_storage_single()
function_graph: Add READ_ONCE() when accessing fgraph_array[]
ftrace: Add missing kerneldoc parameters to unregister_ftrace_direct()
function_graph: Everyone uses HAVE_FUNCTION_GRAPH_RET_ADDR_PTR, remove it
function_graph: Fix up ftrace_graph_ret_addr()
function_graph: Make fgraph_update_pid_func() a stub for !DYNAMIC_FTRACE
function_graph: Rename BYTE_NUMBER to CHAR_NUMBER in selftests
fgraph: Remove some unused functions
ftrace: Hide one more entry in stack trace when ftrace_pid is enabled
function_graph: Do not update pid func if CONFIG_DYNAMIC_FTRACE not enabled
function_graph: Make fgraph_do_direct static key static
ftrace: Fix prototypes for ftrace_startup/shutdown_subops()
ftrace: Assign RCU list variable with rcu_assign_ptr()
ftrace: Assign ftrace_list_end to ftrace_ops_list type cast to RCU
ftrace: Declare function_trace_op in header to quiet sparse warning
ftrace: Add comments to ftrace_hash_move() and friends
ftrace: Convert "inc" parameter to bool in ftrace_hash_rec_update_modify()
ftrace: Add comments to ftrace_hash_rec_disable/enable()
ftrace: Remove "filter_hash" parameter from __ftrace_hash_rec_update()
ftrace: Rename dup_hash() and comment it
...
Building with W=1 in some configurations produces a false positive
warning for kallsyms:
kernel/kallsyms.c: In function '__sprint_symbol.isra':
kernel/kallsyms.c:503:17: error: 'strcpy' source argument is the same as destination [-Werror=restrict]
503 | strcpy(buffer, name);
| ^~~~~~~~~~~~~~~~~~~~
This originally showed up while building with -O3, but later started
happening in other configurations as well, depending on inlining
decisions. The underlying issue is that the local 'name' variable is
always initialized to the be the same as 'buffer' in the called functions
that fill the buffer, which gcc notices while inlining, though it could
see that the address check always skips the copy.
The calling conventions here are rather unusual, as all of the internal
lookup functions (bpf_address_lookup, ftrace_mod_address_lookup,
ftrace_func_address_lookup, module_address_lookup and
kallsyms_lookup_buildid) already use the provided buffer and either return
the address of that buffer to indicate success, or NULL for failure,
but the callers are written to also expect an arbitrary other buffer
to be returned.
Rework the calling conventions to return the length of the filled buffer
instead of its address, which is simpler and easier to follow as well
as avoiding the warning. Leave only the kallsyms_lookup() calling conventions
unchanged, since that is called from 16 different functions and
adapting this would be a much bigger change.
Link: https://lore.kernel.org/lkml/20200107214042.855757-1-arnd@arndb.de/
Link: https://lore.kernel.org/lkml/20240326130647.7bfb1d92@gandalf.local.home/
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Acked-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
While adding comments to the function __ftrace_hash_rec_update() and
trying to describe in detail what the parameter for "filter_hash" does, I
realized that it basically does exactly the same thing (but differently)
if it is set or not!
If it is set, the idea was the ops->filter_hash was being updated, and the
code should focus on the functions that are in the ops->filter_hash and
add them. But it still had to pay attention to the functions in the
ops->notrace_hash, to ignore them.
If it was cleared, it focused on the ops->notrace_hash, and would add
functions that were not in the ops->notrace_hash but would still keep
functions in the "ops->filter_hash". Basically doing the same thing.
In reality, the __ftrace_hash_rec_update() only needs to either remove the
functions associated to the give ops (if "inc" is set) or remove them (if
"inc" is cleared). It has to pay attention to both the filter_hash and
notrace_hash regardless.
Remove the "filter_hash" parameter from __filter_hash_rec_update() and
comment the function for what it really is doing.
Link: https://lore.kernel.org/linux-trace-kernel/20240605180408.691995506@goodmis.org
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
There are cases where a single system will use a single function callback
to handle multiple users. For example, to allow function_graph tracer to
have multiple users where each can trace their own set of functions, it is
useful to only have one ftrace_ops registered to ftrace that will call a
function by the function_graph tracer to handle the multiplexing with the
different registered function_graph tracers.
Add a "subop_list" to the ftrace_ops that will hold a list of other
ftrace_ops that the top ftrace_ops will manage.
The function ftrace_startup_subops() that takes the manager ftrace_ops and
a subop ftrace_ops it will manage. If there are no subops with the
ftrace_ops yet, it will copy the ftrace_ops subop filters to the manager
ftrace_ops and register that with ftrace_startup(), and adds the subop to
its subop_list. If the manager ops already has something registered, it
will then merge the new subop filters with what it has and enable the new
functions that covers all the subops it has.
To remove a subop, ftrace_shutdown_subops() is called which will use the
subop_list of the manager ops to rebuild all the functions it needs to
trace, and update the ftrace records to only call the functions it now has
registered. If there are no more functions registered, it will then call
ftrace_shutdown() to disable itself completely.
Note, it is up to the manager ops callback to always make sure that the
subops callbacks are called if its filter matches, as there are times in
the update where the callback could be calling more functions than those
that are currently registered.
This could be updated to handle other systems other than function_graph,
for example, fprobes could use this (but will need an interface to call
ftrace_startup_subops()).
Link: https://lore.kernel.org/linux-trace-kernel/20240603190822.508431129@goodmis.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Cc: Florent Revest <revest@chromium.org>
Cc: Martin KaFai Lau <martin.lau@linux.dev>
Cc: bpf <bpf@vger.kernel.org>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alan Maguire <alan.maguire@oracle.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Guo Ren <guoren@kernel.org>
Reviewed-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Pull tracing updates from Steven Rostedt:
- Remove unused ftrace_direct_funcs variables
- Fix a possible NULL pointer dereference race in eventfs
- Update do_div() usage in trace event benchmark test
- Speedup direct function registration with asynchronous RCU callback.
The synchronization was done in the registration code and this caused
delays when registering direct callbacks. Move the freeing to a
call_rcu() that will prevent delaying of the registering.
- Replace simple_strtoul() usage with kstrtoul()
* tag 'trace-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
eventfs: Fix a possible null pointer dereference in eventfs_find_events()
ftrace: Fix possible use-after-free issue in ftrace_location()
ftrace: Remove unused global 'ftrace_direct_func_count'
ftrace: Remove unused list 'ftrace_direct_funcs'
tracing: Improve benchmark test performance by using do_div()
ftrace: Use asynchronous grace period for register_ftrace_direct()
ftrace: Replaces simple_strtoul in ftrace
Pull probes updates from Masami Hiramatsu:
- tracing/probes: Add new pseudo-types %pd and %pD support for dumping
dentry name from 'struct dentry *' and file name from 'struct file *'
- uprobes performance optimizations:
- Speed up the BPF uprobe event by delaying the fetching of the
uprobe event arguments that are not used in BPF
- Avoid locking by speculatively checking whether uprobe event is
valid
- Reduce lock contention by using read/write_lock instead of
spinlock for uprobe list operation. This improved BPF uprobe
benchmark result 43% on average
- rethook: Remove non-fatal warning messages when tracing stack from
BPF and skip rcu_is_watching() validation in rethook if possible
- objpool: Optimize objpool (which is used by kretprobes and fprobe as
rethook backend storage) by inlining functions and avoid caching
nr_cpu_ids because it is a const value
- fprobe: Add entry/exit callbacks types (code cleanup)
- kprobes: Check ftrace was killed in kprobes if it uses ftrace
* tag 'probes-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
kprobe/ftrace: bail out if ftrace was killed
selftests/ftrace: Fix required features for VFS type test case
objpool: cache nr_possible_cpus() and avoid caching nr_cpu_ids
objpool: enable inlining objpool_push() and objpool_pop() operations
rethook: honor CONFIG_FTRACE_VALIDATE_RCU_IS_WATCHING in rethook_try_get()
ftrace: make extra rcu_is_watching() validation check optional
uprobes: reduce contention on uprobes_tree access
rethook: Remove warning messages printed for finding return address of a frame.
fprobe: Add entry/exit callbacks types
selftests/ftrace: add fprobe test cases for VFS type "%pd" and "%pD"
selftests/ftrace: add kprobe test cases for VFS type "%pd" and "%pD"
Documentation: tracing: add new type '%pd' and '%pD' for kprobe
tracing/probes: support '%pD' type for print struct file's name
tracing/probes: support '%pd' type for print struct dentry's name
uprobes: add speculative lockless system-wide uprobe filter check
uprobes: prepare uprobe args buffer lazily
uprobes: encapsulate preparation of uprobe args buffer
Pull sysctl updates from Joel Granados:
- Remove sentinel elements from ctl_table structs in kernel/*
Removing sentinels in ctl_table arrays reduces the build time size
and runtime memory consumed by ~64 bytes per array. Removals for
net/, io_uring/, mm/, ipc/ and security/ are set to go into mainline
through their respective subsystems making the next release the most
likely place where the final series that removes the check for
proc_name == NULL will land.
This adds to removals already in arch/, drivers/ and fs/.
- Adjust ctl_table definitions and references to allow constification
- Remove unused ctl_table function arguments
- Move non-const elements from ctl_table to ctl_table_header
- Make ctl_table pointers const in ctl_table_root structure
Making the static ctl_table structs const will increase safety by
keeping the pointers to proc_handler functions in .rodata. Though no
ctl_tables where made const in this PR, the ground work for making
that possible has started with these changes sent by Thomas
Weißschuh.
* tag 'sysctl-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/sysctl/sysctl:
sysctl: drop now unnecessary out-of-bounds check
sysctl: move sysctl type to ctl_table_header
sysctl: drop sysctl_is_perm_empty_ctl_table
sysctl: treewide: constify argument ctl_table_root::permissions(table)
sysctl: treewide: drop unused argument ctl_table_root::set_ownership(table)
bpf: Remove the now superfluous sentinel elements from ctl_table array
delayacct: Remove the now superfluous sentinel elements from ctl_table array
kprobes: Remove the now superfluous sentinel elements from ctl_table array
printk: Remove the now superfluous sentinel elements from ctl_table array
scheduler: Remove the now superfluous sentinel elements from ctl_table array
seccomp: Remove the now superfluous sentinel elements from ctl_table array
timekeeping: Remove the now superfluous sentinel elements from ctl_table array
ftrace: Remove the now superfluous sentinel elements from ctl_table array
umh: Remove the now superfluous sentinel elements from ctl_table array
kernel misc: Remove the now superfluous sentinel elements from ctl_table array
If an error happens in ftrace, ftrace_kill() will prevent disarming
kprobes. Eventually, the ftrace_ops associated with the kprobes will be
freed, yet the kprobes will still be active, and when triggered, they
will use the freed memory, likely resulting in a page fault and panic.
This behavior can be reproduced quite easily, by creating a kprobe and
then triggering a ftrace_kill(). For simplicity, we can simulate an
ftrace error with a kernel module like [1]:
[1]: https://github.com/brenns10/kernel_stuff/tree/master/ftrace_killer
sudo perf probe --add commit_creds
sudo perf trace -e probe:commit_creds
# In another terminal
make
sudo insmod ftrace_killer.ko # calls ftrace_kill(), simulating bug
# Back to perf terminal
# ctrl-c
sudo perf probe --del commit_creds
After a short period, a page fault and panic would occur as the kprobe
continues to execute and uses the freed ftrace_ops. While ftrace_kill()
is supposed to be used only in extreme circumstances, it is invoked in
FTRACE_WARN_ON() and so there are many places where an unexpected bug
could be triggered, yet the system may continue operating, possibly
without the administrator noticing. If ftrace_kill() does not panic the
system, then we should do everything we can to continue operating,
rather than leave a ticking time bomb.
Link: https://lore.kernel.org/all/20240501162956.229427-1-stephen.s.brennan@oracle.com/
Signed-off-by: Stephen Brennan <stephen.s.brennan@oracle.com>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Acked-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
KASAN reports a bug:
BUG: KASAN: use-after-free in ftrace_location+0x90/0x120
Read of size 8 at addr ffff888141d40010 by task insmod/424
CPU: 8 PID: 424 Comm: insmod Tainted: G W 6.9.0-rc2+
[...]
Call Trace:
<TASK>
dump_stack_lvl+0x68/0xa0
print_report+0xcf/0x610
kasan_report+0xb5/0xe0
ftrace_location+0x90/0x120
register_kprobe+0x14b/0xa40
kprobe_init+0x2d/0xff0 [kprobe_example]
do_one_initcall+0x8f/0x2d0
do_init_module+0x13a/0x3c0
load_module+0x3082/0x33d0
init_module_from_file+0xd2/0x130
__x64_sys_finit_module+0x306/0x440
do_syscall_64+0x68/0x140
entry_SYSCALL_64_after_hwframe+0x71/0x79
The root cause is that, in lookup_rec(), ftrace record of some address
is being searched in ftrace pages of some module, but those ftrace pages
at the same time is being freed in ftrace_release_mod() as the
corresponding module is being deleted:
CPU1 | CPU2
register_kprobes() { | delete_module() {
check_kprobe_address_safe() { |
arch_check_ftrace_location() { |
ftrace_location() { |
lookup_rec() // USE! | ftrace_release_mod() // Free!
To fix this issue:
1. Hold rcu lock as accessing ftrace pages in ftrace_location_range();
2. Use ftrace_location_range() instead of lookup_rec() in
ftrace_location();
3. Call synchronize_rcu() before freeing any ftrace pages both in
ftrace_process_locs()/ftrace_release_mod()/ftrace_free_mem().
Link: https://lore.kernel.org/linux-trace-kernel/20240509192859.1273558-1-zhengyejian1@huawei.com
Cc: stable@vger.kernel.org
Cc: <mhiramat@kernel.org>
Cc: <mark.rutland@arm.com>
Cc: <mathieu.desnoyers@efficios.com>
Fixes: ae6aa16fdc ("kprobes: introduce ftrace based optimization")
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Zheng Yejian <zhengyejian1@huawei.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
The function simple_strtoul performs no error checking in scenarios
where the input value overflows the intended output variable.
This results in this function successfully returning, even when the
output does not match the input string (aka the function returns
successfully even when the result is wrong).
Or as it was mentioned [1], "...simple_strtol(), simple_strtoll(),
simple_strtoul(), and simple_strtoull() functions explicitly ignore
overflows, which may lead to unexpected results in callers."
Hence, the use of those functions is discouraged.
This patch replaces all uses of the simple_strtoul with the safer
alternatives kstrtoul and kstruint.
Callers affected:
- add_rec_by_index
- set_graph_max_depth_function
Side effects of this patch:
- Since `fgraph_max_depth` is an `unsigned int`, this patch uses
kstrtouint instead of kstrtoul to avoid any compiler warnings
that could originate from calling the latter.
- This patch ensures that the callers of kstrtou* return accordingly
when kstrtoul and kstruint fail for some reason.
In this case, both callers this patch is addressing return 0 on error.
[1] https://www.kernel.org/doc/html/latest/process/deprecated.html#simple-strtol-simple-strtoll-simple-strtoul-simple-strtoull
Link: https://lore.kernel.org/linux-trace-kernel/GV1PR10MB656333529A8D7B8AFB28D238E8B4A@GV1PR10MB6563.EURPRD10.PROD.OUTLOOK.COM
Signed-off-by: Yuran Pereira <yuran.pereira@hotmail.com>
Reviewed-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
This commit comes at the tail end of a greater effort to remove the
empty elements at the end of the ctl_table arrays (sentinels) which
will reduce the overall build time size of the kernel and run time
memory bloat by ~64 bytes per sentinel (further information Link :
https://lore.kernel.org/all/ZO5Yx5JFogGi%2FcBo@bombadil.infradead.org/)
Remove sentinel elements from ftrace_sysctls and user_event_sysctls
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Acked-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Joel Granados <j.granados@samsung.com>
The advent of CONFIG_PREEMPT_AUTO, AKA lazy preemption, will mean that
even kernels built with CONFIG_PREEMPT_NONE or CONFIG_PREEMPT_VOLUNTARY
might see the occasional preemption, and that this preemption just might
happen within a trampoline.
Therefore, update ftrace_shutdown() to invoke synchronize_rcu_tasks()
based on CONFIG_TASKS_RCU instead of CONFIG_PREEMPTION.
[ paulmck: Apply Steven Rostedt feedback. ]
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Ankur Arora <ankur.a.arora@oracle.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: <linux-trace-kernel@vger.kernel.org>
Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Commit a8b9cf62ad ("ftrace: Fix DIRECT_CALLS to use SAVE_REGS by
default") attempted to fix an issue with direct trampolines on x86, see
its description for details. However, it wrongly referenced the
HAVE_DYNAMIC_FTRACE_WITH_REGS config option and the problem is still
present.
Add the missing "CONFIG_" prefix for the logic to work as intended.
Link: https://lore.kernel.org/linux-trace-kernel/20240213132434.22537-1-petr.pavlu@suse.com
Fixes: a8b9cf62ad ("ftrace: Fix DIRECT_CALLS to use SAVE_REGS by default")
Signed-off-by: Petr Pavlu <petr.pavlu@suse.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
The commit 60c8971899 ("ftrace: Make DIRECT_CALLS work WITH_ARGS
and !WITH_REGS") changed DIRECT_CALLS to use SAVE_ARGS when there
are multiple ftrace_ops at the same function, but since the x86 only
support to jump to direct_call from ftrace_regs_caller, when we set
the function tracer on the same target function on x86, ftrace-direct
does not work as below (this actually works on arm64.)
At first, insmod ftrace-direct.ko to put a direct_call on
'wake_up_process()'.
# insmod kernel/samples/ftrace/ftrace-direct.ko
# less trace
...
<idle>-0 [006] ..s1. 564.686958: my_direct_func: waking up rcu_preempt-17
<idle>-0 [007] ..s1. 564.687836: my_direct_func: waking up kcompactd0-63
<idle>-0 [006] ..s1. 564.690926: my_direct_func: waking up rcu_preempt-17
<idle>-0 [006] ..s1. 564.696872: my_direct_func: waking up rcu_preempt-17
<idle>-0 [007] ..s1. 565.191982: my_direct_func: waking up kcompactd0-63
Setup a function filter to the 'wake_up_process' too, and enable it.
# cd /sys/kernel/tracing/
# echo wake_up_process > set_ftrace_filter
# echo function > current_tracer
# less trace
...
<idle>-0 [006] ..s3. 686.180972: wake_up_process <-call_timer_fn
<idle>-0 [006] ..s3. 686.186919: wake_up_process <-call_timer_fn
<idle>-0 [002] ..s3. 686.264049: wake_up_process <-call_timer_fn
<idle>-0 [002] d.h6. 686.515216: wake_up_process <-kick_pool
<idle>-0 [002] d.h6. 686.691386: wake_up_process <-kick_pool
Then, only function tracer is shown on x86.
But if you enable 'kprobe on ftrace' event (which uses SAVE_REGS flag)
on the same function, it is shown again.
# echo 'p wake_up_process' >> dynamic_events
# echo 1 > events/kprobes/p_wake_up_process_0/enable
# echo > trace
# less trace
...
<idle>-0 [006] ..s2. 2710.345919: p_wake_up_process_0: (wake_up_process+0x4/0x20)
<idle>-0 [006] ..s3. 2710.345923: wake_up_process <-call_timer_fn
<idle>-0 [006] ..s1. 2710.345928: my_direct_func: waking up rcu_preempt-17
<idle>-0 [006] ..s2. 2710.349931: p_wake_up_process_0: (wake_up_process+0x4/0x20)
<idle>-0 [006] ..s3. 2710.349934: wake_up_process <-call_timer_fn
<idle>-0 [006] ..s1. 2710.349937: my_direct_func: waking up rcu_preempt-17
To fix this issue, use SAVE_REGS flag for multiple ftrace_ops flag of
direct_call by default.
Link: https://lore.kernel.org/linux-trace-kernel/170484558617.178953.1590516949390270842.stgit@devnote2
Fixes: 60c8971899 ("ftrace: Make DIRECT_CALLS work WITH_ARGS and !WITH_REGS")
Cc: stable@vger.kernel.org
Cc: Florent Revest <revest@chromium.org>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com> [arm64]
Acked-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Masami Hiramatsu reported a memory leak in register_ftrace_direct() where
if the number of new entries are added is large enough to cause two
allocations in the loop:
for (i = 0; i < size; i++) {
hlist_for_each_entry(entry, &hash->buckets[i], hlist) {
new = ftrace_add_rec_direct(entry->ip, addr, &free_hash);
if (!new)
goto out_remove;
entry->direct = addr;
}
}
Where ftrace_add_rec_direct() has:
if (ftrace_hash_empty(direct_functions) ||
direct_functions->count > 2 * (1 << direct_functions->size_bits)) {
struct ftrace_hash *new_hash;
int size = ftrace_hash_empty(direct_functions) ? 0 :
direct_functions->count + 1;
if (size < 32)
size = 32;
new_hash = dup_hash(direct_functions, size);
if (!new_hash)
return NULL;
*free_hash = direct_functions;
direct_functions = new_hash;
}
The "*free_hash = direct_functions;" can happen twice, losing the previous
allocation of direct_functions.
But this also exposed a more serious bug.
The modification of direct_functions above is not safe. As
direct_functions can be referenced at any time to find what direct caller
it should call, the time between:
new_hash = dup_hash(direct_functions, size);
and
direct_functions = new_hash;
can have a race with another CPU (or even this one if it gets interrupted),
and the entries being moved to the new hash are not referenced.
That's because the "dup_hash()" is really misnamed and is really a
"move_hash()". It moves the entries from the old hash to the new one.
Now even if that was changed, this code is not proper as direct_functions
should not be updated until the end. That is the best way to handle
function reference changes, and is the way other parts of ftrace handles
this.
The following is done:
1. Change add_hash_entry() to return the entry it created and inserted
into the hash, and not just return success or not.
2. Replace ftrace_add_rec_direct() with add_hash_entry(), and remove
the former.
3. Allocate a "new_hash" at the start that is made for holding both the
new hash entries as well as the existing entries in direct_functions.
4. Copy (not move) the direct_function entries over to the new_hash.
5. Copy the entries of the added hash to the new_hash.
6. If everything succeeds, then use rcu_pointer_assign() to update the
direct_functions with the new_hash.
This simplifies the code and fixes both the memory leak as well as the
race condition mentioned above.
Link: https://lore.kernel.org/all/170368070504.42064.8960569647118388081.stgit@devnote2/
Link: https://lore.kernel.org/linux-trace-kernel/20231229115134.08dd5174@gandalf.local.home
Cc: stable@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Fixes: 763e34e74b ("ftrace: Add register_ftrace_direct()")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
As comments in ftrace_process_locs(), there may be NULL pointers in
mcount_loc section:
> Some architecture linkers will pad between
> the different mcount_loc sections of different
> object files to satisfy alignments.
> Skip any NULL pointers.
After commit 20e5227e9f ("ftrace: allow NULL pointers in mcount_loc"),
NULL pointers will be accounted when allocating ftrace pages but skipped
before adding into ftrace pages, this may result in some pages not being
used. Then after commit 706c81f87f ("ftrace: Remove extra helper
functions"), warning may occur at:
WARN_ON(pg->next);
To fix it, only warn for case that no pointers skipped but pages not used
up, then free those unused pages after releasing ftrace_lock.
Link: https://lore.kernel.org/linux-trace-kernel/20230712060452.3175675-1-zhengyejian1@huawei.com
Cc: stable@vger.kernel.org
Fixes: 706c81f87f ("ftrace: Remove extra helper functions")
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Zheng Yejian <zhengyejian1@huawei.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Pull tracing updates from Steven Rostedt:
- Add new feature to have function graph tracer record the return
value. Adds a new option: funcgraph-retval ; when set, will show the
return value of a function in the function graph tracer.
- Also add the option: funcgraph-retval-hex where if it is not set, and
the return value is an error code, then it will return the decimal of
the error code, otherwise it still reports the hex value.
- Add the file /sys/kernel/tracing/osnoise/per_cpu/cpu<cpu>/timerlat_fd
That when a application opens it, it becomes the task that the timer
lat tracer traces. The application can also read this file to find
out how it's being interrupted.
- Add the file /sys/kernel/tracing/available_filter_functions_addrs
that works just the same as available_filter_functions but also shows
the addresses of the functions like kallsyms, except that it gives
the address of where the fentry/mcount jump/nop is. This is used by
BPF to make it easier to attach BPF programs to ftrace hooks.
- Replace strlcpy with strscpy in the tracing boot code.
* tag 'trace-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Fix warnings when building htmldocs for function graph retval
riscv: ftrace: Enable HAVE_FUNCTION_GRAPH_RETVAL
tracing/boot: Replace strlcpy with strscpy
tracing/timerlat: Add user-space interface
tracing/osnoise: Skip running osnoise if all instances are off
tracing/osnoise: Switch from PF_NO_SETAFFINITY to migrate_disable
ftrace: Show all functions with addresses in available_filter_functions_addrs
selftests/ftrace: Add funcgraph-retval test case
LoongArch: ftrace: Enable HAVE_FUNCTION_GRAPH_RETVAL
x86/ftrace: Enable HAVE_FUNCTION_GRAPH_RETVAL
arm64: ftrace: Enable HAVE_FUNCTION_GRAPH_RETVAL
tracing: Add documentation for funcgraph-retval and funcgraph-retval-hex
function_graph: Support recording and printing the return value of function
fgraph: Add declaration of "struct fgraph_ret_regs"
