[ Upstream commit 0cadf8534f ]
The Event_Type field in an LE Extended Advertising Report uses bits 5
and 6 for data status (e.g. truncation or fragmentation), not the PDU
type itself.
The ext_evt_type_to_legacy() function fails to mask these status bits
before evaluation. This causes valid advertisements with status bits set
(e.g. a truncated non-connectable advertisement, which ends up showing
as PDU type 0x40) to be misclassified as unknown and subsequently
dropped. This is okay for most checks which use bitwise AND on the
relevant event type bits, but it doesn't work for non-connectable types,
which are checked with '== LE_EXT_ADV_NON_CONN_IND' (that is, zero).
In terms of behaviour, first the device sends a truncated report:
> HCI Event: LE Meta Event (0x3e) plen 26
LE Extended Advertising Report (0x0d)
Entry 0
Event type: 0x0040
Data status: Incomplete, data truncated, no more to come
Address type: Random (0x01)
Address: 1D:12:46:FA:F8:6E (Non-Resolvable)
SID: 0x03
RSSI: -98 dBm (0x9e)
Data length: 0x00
Then, a few seconds later, it sends the subsequent complete report:
> HCI Event: LE Meta Event (0x3e) plen 122
LE Extended Advertising Report (0x0d)
Entry 0
Event type: 0x0000
Data status: Complete
Address type: Random (0x01)
Address: 1D:12:46:FA:F8:6E (Non-Resolvable)
SID: 0x03
RSSI: -97 dBm (0x9f)
Data length: 0x60
Service Data: Google (0xfef3)
Data[92]: ...
These devices often send multiple truncated reports per second.
This patch introduces a PDU type mask to ensure only the relevant bits
are evaluated, allowing for the correct translation of all valid
extended advertising packets.
Fixes: b2cc9761f1 ("Bluetooth: Handle extended ADV PDU types")
Signed-off-by: Chris Down <chris@chrisdown.name>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d24e4a7fed ]
Configuration request only configure the incoming direction of the peer
initiating the request, so using the MTU is the other direction shall
not be used, that said the spec allows the peer responding to adjust:
Bluetooth Core 6.1, Vol 3, Part A, Section 4.5
'Each configuration parameter value (if any is present) in an
L2CAP_CONFIGURATION_RSP packet reflects an ‘adjustment’ to a
configuration parameter value that has been sent (or, in case of
default values, implied) in the corresponding
L2CAP_CONFIGURATION_REQ packet.'
That said adjusting the MTU in the response shall be limited to ERTM
channels only as for older modes the remote stack may not be able to
detect the adjustment causing it to silently drop packets.
Link: https://github.com/bluez/bluez/issues/1422
Link: https://gitlab.archlinux.org/archlinux/packaging/packages/linux/-/issues/149
Link: https://gitlab.freedesktop.org/pipewire/pipewire/-/issues/4793
Fixes: 042bb9603c ("Bluetooth: L2CAP: Fix L2CAP MTU negotiation")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ef99c9176 ]
This replaces the usage of HCI_ERROR_REMOTE_USER_TERM, which as the name
suggest is to indicate a regular disconnection initiated by an user,
with HCI_ERROR_AUTH_FAILURE to indicate the session has timeout thus any
pairing shall be considered as failed.
Fixes: 1e91c29eb6 ("Bluetooth: Use hci_disconnect for immediate disconnection from SMP")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe4840df0b ]
If a command is received while a bonding is ongoing consider it a
pairing failure so the session is cleanup properly and the device is
disconnected immediately instead of continuing with other commands that
may result in the session to get stuck without ever completing such as
the case bellow:
> ACL Data RX: Handle 2048 flags 0x02 dlen 21
SMP: Identity Information (0x08) len 16
Identity resolving key[16]: d7e08edef97d3e62cd2331f82d8073b0
> ACL Data RX: Handle 2048 flags 0x02 dlen 21
SMP: Signing Information (0x0a) len 16
Signature key[16]: 1716c536f94e843a9aea8b13ffde477d
Bluetooth: hci0: unexpected SMP command 0x0a from XX:XX:XX:XX:XX:XX
> ACL Data RX: Handle 2048 flags 0x02 dlen 12
SMP: Identity Address Information (0x09) len 7
Address: XX:XX:XX:XX:XX:XX (Intel Corporate)
While accourding to core spec 6.1 the expected order is always BD_ADDR
first first then CSRK:
When using LE legacy pairing, the keys shall be distributed in the
following order:
LTK by the Peripheral
EDIV and Rand by the Peripheral
IRK by the Peripheral
BD_ADDR by the Peripheral
CSRK by the Peripheral
LTK by the Central
EDIV and Rand by the Central
IRK by the Central
BD_ADDR by the Central
CSRK by the Central
When using LE Secure Connections, the keys shall be distributed in the
following order:
IRK by the Peripheral
BD_ADDR by the Peripheral
CSRK by the Peripheral
IRK by the Central
BD_ADDR by the Central
CSRK by the Central
According to the Core 6.1 for commands used for key distribution "Key
Rejected" can be used:
'3.6.1. Key distribution and generation
A device may reject a distributed key by sending the Pairing Failed command
with the reason set to "Key Rejected".
Fixes: b28b494366 ("Bluetooth: Add strict checks for allowed SMP PDUs")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d85edab911 ]
Currently, the connectable flag used by the setup of an extended
advertising instance drives whether we require privacy when trying to pass
a random address to the advertising parameters (Own Address).
If privacy is not required, then it automatically falls back to using the
controller's public address. This can cause problems when using controllers
that do not have a public address set, but instead use a static random
address.
e.g. Assume a BLE controller that does not have a public address set.
The controller upon powering is set with a random static address by default
by the kernel.
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6
Address: E4:AF:26:D8:3E:3A (Static)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Random Address (0x08|0x0005) ncmd 1
Status: Success (0x00)
Setting non-connectable extended advertisement parameters in bluetoothctl
mgmt
add-ext-adv-params -r 0x801 -x 0x802 -P 2M -g 1
correctly sets Own address type as Random
< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036)
plen 25
...
Own address type: Random (0x01)
Setting connectable extended advertisement parameters in bluetoothctl mgmt
add-ext-adv-params -r 0x801 -x 0x802 -P 2M -g -c 1
mistakenly sets Own address type to Public (which causes to use Public
Address 00:00:00:00:00:00)
< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036)
plen 25
...
Own address type: Public (0x00)
This causes either the controller to emit an Invalid Parameters error or to
mishandle the advertising.
This patch makes sure that we use the already set static random address
when requesting a connectable extended advertising when we don't require
privacy and our public address is not set (00:00:00:00:00:00).
Fixes: 3fe318ee72 ("Bluetooth: move hci_get_random_address() to hci_sync")
Signed-off-by: Alessandro Gasbarroni <alex.gasbarroni@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7349772c2 ]
Upon receiving HCI_EVT_LE_BIG_SYNC_ESTABLISHED with status 0x00
(success) the corresponding BIS hci_conn state shall be set to
BT_CONNECTED otherwise they will be left with BT_OPEN which is invalid
at that point, also create the debugfs and sysfs entries following the
same logic as the likes of Broadcast Source BIS and CIS connections.
Fixes: f777d88278 ("Bluetooth: ISO: Notify user space about failed bis connections")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef9675b0ef ]
As the code comments on hci_setup_ext_adv_instance_sync suggests the
advertising instance needs to be disabled in order to update its
parameters, but it was wrongly checking that !adv->pending.
Fixes: cba6b75871 ("Bluetooth: hci_sync: Make use of hci_cmd_sync_queue set 2")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f3cb5676e5 upstream.
The unconditional call of hci_disable_advertising_sync() in
mesh_send_done_sync() also disables other LE advertisings (non mesh
related).
I am not sure whether this call is required at all, but checking the
adv_instances list (like done at other places) seems to solve the
problem.
Fixes: b338d91703 ("Bluetooth: Implement support for Mesh")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46c0d947b6 upstream.
This reverts minor parts of the changes made in commit b338d91703
("Bluetooth: Implement support for Mesh"). It looks like these changes
were only made for development purposes but shouldn't have been part of
the commit.
Fixes: b338d91703 ("Bluetooth: Implement support for Mesh")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89fb8acc38 upstream.
Currently, for controllers with extended advertising, the advertising
data is set in the asynchronous response handler for extended
adverstising params. As most advertising settings are performed in a
synchronous context, the (asynchronous) setting of the advertising data
is done too late (after enabling the advertising).
Move setting of adverstising data from asynchronous response handler
into synchronous context to fix ordering of HCI commands.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Fixes: a0fb3726ba ("Bluetooth: Use Set ext adv/scan rsp data if controller supports")
Cc: stable@vger.kernel.org
v2: https://lore.kernel.org/linux-bluetooth/20250626115209.17839-1-ceggers@arri.de/
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 042bb9603c upstream.
OBEX download from iPhone is currently slow due to small packet size
used to transfer data which doesn't follow the MTU negotiated during
L2CAP connection, i.e. 672 bytes instead of 32767:
< ACL Data TX: Handle 11 flags 0x00 dlen 12
L2CAP: Connection Request (0x02) ident 18 len 4
PSM: 4103 (0x1007)
Source CID: 72
> ACL Data RX: Handle 11 flags 0x02 dlen 16
L2CAP: Connection Response (0x03) ident 18 len 8
Destination CID: 14608
Source CID: 72
Result: Connection successful (0x0000)
Status: No further information available (0x0000)
< ACL Data TX: Handle 11 flags 0x00 dlen 27
L2CAP: Configure Request (0x04) ident 20 len 19
Destination CID: 14608
Flags: 0x0000
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 32767
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Enhanced Retransmission (0x03)
TX window size: 63
Max transmit: 3
Retransmission timeout: 2000
Monitor timeout: 12000
Maximum PDU size: 1009
> ACL Data RX: Handle 11 flags 0x02 dlen 26
L2CAP: Configure Request (0x04) ident 72 len 18
Destination CID: 72
Flags: 0x0000
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Enhanced Retransmission (0x03)
TX window size: 32
Max transmit: 255
Retransmission timeout: 0
Monitor timeout: 0
Maximum PDU size: 65527
Option: Frame Check Sequence (0x05) [mandatory]
FCS: 16-bit FCS (0x01)
< ACL Data TX: Handle 11 flags 0x00 dlen 29
L2CAP: Configure Response (0x05) ident 72 len 21
Source CID: 14608
Flags: 0x0000
Result: Success (0x0000)
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 672
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Enhanced Retransmission (0x03)
TX window size: 32
Max transmit: 255
Retransmission timeout: 2000
Monitor timeout: 12000
Maximum PDU size: 1009
> ACL Data RX: Handle 11 flags 0x02 dlen 32
L2CAP: Configure Response (0x05) ident 20 len 24
Source CID: 72
Flags: 0x0000
Result: Success (0x0000)
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 32767
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Enhanced Retransmission (0x03)
TX window size: 63
Max transmit: 3
Retransmission timeout: 2000
Monitor timeout: 12000
Maximum PDU size: 1009
Option: Frame Check Sequence (0x05) [mandatory]
FCS: 16-bit FCS (0x01)
...
> ACL Data RX: Handle 11 flags 0x02 dlen 680
Channel: 72 len 676 ctrl 0x0202 [PSM 4103 mode Enhanced Retransmission (0x03)] {chan 8}
I-frame: Unsegmented TxSeq 1 ReqSeq 2
< ACL Data TX: Handle 11 flags 0x00 dlen 13
Channel: 14608 len 9 ctrl 0x0204 [PSM 4103 mode Enhanced Retransmission (0x03)] {chan 8}
I-frame: Unsegmented TxSeq 2 ReqSeq 2
> ACL Data RX: Handle 11 flags 0x02 dlen 680
Channel: 72 len 676 ctrl 0x0304 [PSM 4103 mode Enhanced Retransmission (0x03)] {chan 8}
I-frame: Unsegmented TxSeq 2 ReqSeq 3
The MTUs are negotiated for each direction. In this traces 32767 for
iPhone->localhost and no MTU for localhost->iPhone, which based on
'4.4 L2CAP_CONFIGURATION_REQ' (Core specification v5.4, Vol. 3, Part
A):
The only parameters that should be included in the
L2CAP_CONFIGURATION_REQ packet are those that require different
values than the default or previously agreed values.
...
Any missing configuration parameters are assumed to have their
most recently explicitly or implicitly accepted values.
and '5.1 Maximum transmission unit (MTU)':
If the remote device sends a positive L2CAP_CONFIGURATION_RSP
packet it should include the actual MTU to be used on this channel
for traffic flowing into the local device.
...
The default value is 672 octets.
is set by BlueZ to 672 bytes.
It seems that the iPhone used the lowest negotiated value to transfer
data to the localhost instead of the negotiated one for the incoming
direction.
This could be fixed by using the MTU negotiated for the other
direction, if exists, in the L2CAP_CONFIGURATION_RSP.
This allows to use segmented packets as in the following traces:
< ACL Data TX: Handle 11 flags 0x00 dlen 12
L2CAP: Connection Request (0x02) ident 22 len 4
PSM: 4103 (0x1007)
Source CID: 72
< ACL Data TX: Handle 11 flags 0x00 dlen 27
L2CAP: Configure Request (0x04) ident 24 len 19
Destination CID: 2832
Flags: 0x0000
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 32767
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Enhanced Retransmission (0x03)
TX window size: 63
Max transmit: 3
Retransmission timeout: 2000
Monitor timeout: 12000
Maximum PDU size: 1009
> ACL Data RX: Handle 11 flags 0x02 dlen 26
L2CAP: Configure Request (0x04) ident 15 len 18
Destination CID: 72
Flags: 0x0000
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Enhanced Retransmission (0x03)
TX window size: 32
Max transmit: 255
Retransmission timeout: 0
Monitor timeout: 0
Maximum PDU size: 65527
Option: Frame Check Sequence (0x05) [mandatory]
FCS: 16-bit FCS (0x01)
< ACL Data TX: Handle 11 flags 0x00 dlen 29
L2CAP: Configure Response (0x05) ident 15 len 21
Source CID: 2832
Flags: 0x0000
Result: Success (0x0000)
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 32767
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Enhanced Retransmission (0x03)
TX window size: 32
Max transmit: 255
Retransmission timeout: 2000
Monitor timeout: 12000
Maximum PDU size: 1009
> ACL Data RX: Handle 11 flags 0x02 dlen 32
L2CAP: Configure Response (0x05) ident 24 len 24
Source CID: 72
Flags: 0x0000
Result: Success (0x0000)
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 32767
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Enhanced Retransmission (0x03)
TX window size: 63
Max transmit: 3
Retransmission timeout: 2000
Monitor timeout: 12000
Maximum PDU size: 1009
Option: Frame Check Sequence (0x05) [mandatory]
FCS: 16-bit FCS (0x01)
...
> ACL Data RX: Handle 11 flags 0x02 dlen 1009
Channel: 72 len 1005 ctrl 0x4202 [PSM 4103 mode Enhanced Retransmission (0x03)] {chan 8}
I-frame: Start (len 21884) TxSeq 1 ReqSeq 2
> ACL Data RX: Handle 11 flags 0x02 dlen 1009
Channel: 72 len 1005 ctrl 0xc204 [PSM 4103 mode Enhanced Retransmission (0x03)] {chan 8}
I-frame: Continuation TxSeq 2 ReqSeq 2
This has been tested with kernel 5.4 and BlueZ 5.77.
Cc: stable@vger.kernel.org
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1d6123102e ]
syzbot reported use-after-free in vhci_flush() without repro. [0]
From the splat, a thread close()d a vhci file descriptor while
its device was being used by iotcl() on another thread.
Once the last fd refcnt is released, vhci_release() calls
hci_unregister_dev(), hci_free_dev(), and kfree() for struct
vhci_data, which is set to hci_dev->dev->driver_data.
The problem is that there is no synchronisation after unlinking
hdev from hci_dev_list in hci_unregister_dev(). There might be
another thread still accessing the hdev which was fetched before
the unlink operation.
We can use SRCU for such synchronisation.
Let's run hci_dev_reset() under SRCU and wait for its completion
in hci_unregister_dev().
Another option would be to restore hci_dev->destruct(), which was
removed in commit 587ae086f6 ("Bluetooth: Remove unused
hci-destruct cb"). However, this would not be a good solution, as
we should not run hci_unregister_dev() while there are in-flight
ioctl() requests, which could lead to another data-race KCSAN splat.
Note that other drivers seem to have the same problem, for exmaple,
virtbt_remove().
[0]:
BUG: KASAN: slab-use-after-free in skb_queue_empty_lockless include/linux/skbuff.h:1891 [inline]
BUG: KASAN: slab-use-after-free in skb_queue_purge_reason+0x99/0x360 net/core/skbuff.c:3937
Read of size 8 at addr ffff88807cb8d858 by task syz.1.219/6718
CPU: 1 UID: 0 PID: 6718 Comm: syz.1.219 Not tainted 6.16.0-rc1-syzkaller-00196-g08207f42d3ff #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/07/2025
Call Trace:
<TASK>
dump_stack_lvl+0x189/0x250 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:408 [inline]
print_report+0xd2/0x2b0 mm/kasan/report.c:521
kasan_report+0x118/0x150 mm/kasan/report.c:634
skb_queue_empty_lockless include/linux/skbuff.h:1891 [inline]
skb_queue_purge_reason+0x99/0x360 net/core/skbuff.c:3937
skb_queue_purge include/linux/skbuff.h:3368 [inline]
vhci_flush+0x44/0x50 drivers/bluetooth/hci_vhci.c:69
hci_dev_do_reset net/bluetooth/hci_core.c:552 [inline]
hci_dev_reset+0x420/0x5c0 net/bluetooth/hci_core.c:592
sock_do_ioctl+0xd9/0x300 net/socket.c:1190
sock_ioctl+0x576/0x790 net/socket.c:1311
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:907 [inline]
__se_sys_ioctl+0xf9/0x170 fs/ioctl.c:893
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7fcf5b98e929
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 a8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007fcf5c7b9038 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00007fcf5bbb6160 RCX: 00007fcf5b98e929
RDX: 0000000000000000 RSI: 00000000400448cb RDI: 0000000000000009
RBP: 00007fcf5ba10b39 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 0000000000000000 R14: 00007fcf5bbb6160 R15: 00007ffd6353d528
</TASK>
Allocated by task 6535:
kasan_save_stack mm/kasan/common.c:47 [inline]
kasan_save_track+0x3e/0x80 mm/kasan/common.c:68
poison_kmalloc_redzone mm/kasan/common.c:377 [inline]
__kasan_kmalloc+0x93/0xb0 mm/kasan/common.c:394
kasan_kmalloc include/linux/kasan.h:260 [inline]
__kmalloc_cache_noprof+0x230/0x3d0 mm/slub.c:4359
kmalloc_noprof include/linux/slab.h:905 [inline]
kzalloc_noprof include/linux/slab.h:1039 [inline]
vhci_open+0x57/0x360 drivers/bluetooth/hci_vhci.c:635
misc_open+0x2bc/0x330 drivers/char/misc.c:161
chrdev_open+0x4c9/0x5e0 fs/char_dev.c:414
do_dentry_open+0xdf0/0x1970 fs/open.c:964
vfs_open+0x3b/0x340 fs/open.c:1094
do_open fs/namei.c:3887 [inline]
path_openat+0x2ee5/0x3830 fs/namei.c:4046
do_filp_open+0x1fa/0x410 fs/namei.c:4073
do_sys_openat2+0x121/0x1c0 fs/open.c:1437
do_sys_open fs/open.c:1452 [inline]
__do_sys_openat fs/open.c:1468 [inline]
__se_sys_openat fs/open.c:1463 [inline]
__x64_sys_openat+0x138/0x170 fs/open.c:1463
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Freed by task 6535:
kasan_save_stack mm/kasan/common.c:47 [inline]
kasan_save_track+0x3e/0x80 mm/kasan/common.c:68
kasan_save_free_info+0x46/0x50 mm/kasan/generic.c:576
poison_slab_object mm/kasan/common.c:247 [inline]
__kasan_slab_free+0x62/0x70 mm/kasan/common.c:264
kasan_slab_free include/linux/kasan.h:233 [inline]
slab_free_hook mm/slub.c:2381 [inline]
slab_free mm/slub.c:4643 [inline]
kfree+0x18e/0x440 mm/slub.c:4842
vhci_release+0xbc/0xd0 drivers/bluetooth/hci_vhci.c:671
__fput+0x44c/0xa70 fs/file_table.c:465
task_work_run+0x1d1/0x260 kernel/task_work.c:227
exit_task_work include/linux/task_work.h:40 [inline]
do_exit+0x6ad/0x22e0 kernel/exit.c:955
do_group_exit+0x21c/0x2d0 kernel/exit.c:1104
__do_sys_exit_group kernel/exit.c:1115 [inline]
__se_sys_exit_group kernel/exit.c:1113 [inline]
__x64_sys_exit_group+0x3f/0x40 kernel/exit.c:1113
x64_sys_call+0x21ba/0x21c0 arch/x86/include/generated/asm/syscalls_64.h:232
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
The buggy address belongs to the object at ffff88807cb8d800
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 88 bytes inside of
freed 1024-byte region [ffff88807cb8d800, ffff88807cb8dc00)
Fixes: bf18c7118c ("Bluetooth: vhci: Free driver_data on file release")
Reported-by: syzbot+2faa4825e556199361f9@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=f62d64848fc4c7c30cd6
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5725bc6082 ]
When using and existing adv_info instance for broadcast source it
needs to be updated to periodic first before it can be reused, also in
case the existing instance already have data hci_set_adv_instance_data
cannot be used directly since it would overwrite the existing data so
this reappend the original data after the Broadcast ID, if one was
generated.
Example:
bluetoothctl># Add PBP to EA so it can be later referenced as the BIS ID
bluetoothctl> advertise.service 0x1856 0x00 0x00
bluetoothctl> advertise on
...
< HCI Command: LE Set Extended Advertising Data (0x08|0x0037) plen 13
Handle: 0x01
Operation: Complete extended advertising data (0x03)
Fragment preference: Minimize fragmentation (0x01)
Data length: 0x09
Service Data: Public Broadcast Announcement (0x1856)
Data[2]: 0000
Flags: 0x06
LE General Discoverable Mode
BR/EDR Not Supported
...
bluetoothctl># Attempt to acquire Broadcast Source transport
bluetoothctl>transport.acquire /org/bluez/hci0/pac_bcast0/fd0
...
< HCI Command: LE Set Extended Advertising Data (0x08|0x0037) plen 255
Handle: 0x01
Operation: Complete extended advertising data (0x03)
Fragment preference: Minimize fragmentation (0x01)
Data length: 0x0e
Service Data: Broadcast Audio Announcement (0x1852)
Broadcast ID: 11371620 (0xad8464)
Service Data: Public Broadcast Announcement (0x1856)
Data[2]: 0000
Flags: 0x06
LE General Discoverable Mode
BR/EDR Not Supported
Link: https://github.com/bluez/bluez/issues/1117
Fixes: eca0ae4aea ("Bluetooth: Add initial implementation of BIS connections")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20a2aa01f5 ]
The len parameter is considered optional so it can be NULL so it cannot
be used for skipping to next entry of EIR_SERVICE_DATA.
Fixes: 8f9ae5b3ae ("Bluetooth: eir: Add helpers for managing service data")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 276af34d82 ]
mgmt_pending_find_data() last use was removed in 2021 by
commit 5a75013746 ("Bluetooth: hci_sync: Convert MGMT_OP_GET_CLOCK_INFO")
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stable-dep-of: 6fe26f694c ("Bluetooth: MGMT: Protect mgmt_pending list with its own lock")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 308a3a8ce8 ]
Releasing + re-acquiring RCU lock inside list_for_each_entry_rcu() loop
body is not correct.
Fix by taking the update-side hdev->lock instead.
Fixes: c7eaf80bfb ("Bluetooth: Fix hci_link_tx_to RCU lock usage")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03dba9cea7 ]
Depending on the security set the response to L2CAP_LE_CONN_REQ shall be
just L2CAP_CR_LE_ENCRYPTION if only encryption when BT_SECURITY_MEDIUM
is selected since that means security mode 2 which doesn't require
authentication which is something that is covered in the qualification
test L2CAP/LE/CFC/BV-25-C.
Link: https://github.com/bluez/bluez/issues/1270
Fixes: 27e2d4c8d2 ("Bluetooth: Add basic LE L2CAP connect request receiving support")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3bb88524b7 ]
In 'mgmt_mesh_foreach()', iterate over mesh commands
rather than generic mgmt ones. Compile tested only.
Fixes: b338d91703 ("Bluetooth: Implement support for Mesh")
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2d471b780 ]
Up until now it has been assumed that the application would be able to
enter the advertising SID in sockaddr_iso_bc.bc_sid, but userspace has
no access to SID since the likes of MGMT_EV_DEVICE_FOUND cannot carry
it, so it was left unset (0x00) which means it would be unable to
synchronize if the broadcast source is using a different SID e.g. 0x04:
> HCI Event: LE Meta Event (0x3e) plen 57
LE Extended Advertising Report (0x0d)
Num reports: 1
Entry 0
Event type: 0x0000
Props: 0x0000
Data status: Complete
Address type: Random (0x01)
Address: 0B:82:E8:50:6D:C8 (Non-Resolvable)
Primary PHY: LE 1M
Secondary PHY: LE 2M
SID: 0x04
TX power: 127 dBm
RSSI: -55 dBm (0xc9)
Periodic advertising interval: 180.00 msec (0x0090)
Direct address type: Public (0x00)
Direct address: 00:00:00:00:00:00 (OUI 00-00-00)
Data length: 0x1f
06 16 52 18 5b 0b e1 05 16 56 18 04 00 11 30 4c ..R.[....V....0L
75 69 7a 27 73 20 53 32 33 20 55 6c 74 72 61 uiz's S23 Ultra
Service Data: Broadcast Audio Announcement (0x1852)
Broadcast ID: 14748507 (0xe10b5b)
Service Data: Public Broadcast Announcement (0x1856)
Data[2]: 0400
Unknown EIR field 0x30[16]: 4c75697a27732053323320556c747261
< HCI Command: LE Periodic Advertising Create Sync (0x08|0x0044) plen 14
Options: 0x0000
Use advertising SID, Advertiser Address Type and address
Reporting initially enabled
SID: 0x00 (<- Invalid)
Adv address type: Random (0x01)
Adv address: 0B:82:E8:50:6D:C8 (Non-Resolvable)
Skip: 0x0000
Sync timeout: 20000 msec (0x07d0)
Sync CTE type: 0x0000
So instead this changes now allow application to set HCI_SID_INVALID
which will make hci_le_pa_create_sync to wait for a report, update the
conn->sid using the report SID and only then issue PA create sync
command:
< HCI Command: LE Periodic Advertising Create Sync
Options: 0x0000
Use advertising SID, Advertiser Address Type and address
Reporting initially enabled
SID: 0x04
Adv address type: Random (0x01)
Adv address: 0B:82:E8:50:6D:C8 (Non-Resolvable)
Skip: 0x0000
Sync timeout: 20000 msec (0x07d0)
Sync CTE type: 0x0000
> HCI Event: LE Meta Event (0x3e) plen 16
LE Periodic Advertising Sync Established (0x0e)
Status: Success (0x00)
Sync handle: 64
Advertising SID: 0x04
Advertiser address type: Random (0x01)
Advertiser address: 0B:82:E8:50:6D:C8 (Non-Resolvable)
Advertiser PHY: LE 2M (0x02)
Periodic advertising interval: 180.00 msec (0x0090)
Advertiser clock accuracy: 0x05
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7af8479d9e ]
l2cap_check_enc_key_size shall check the security level of the
l2cap_chan rather than the hci_conn since for incoming connection
request that may be different as hci_conn may already been
encrypted using a different security level.
Fixes: 522e9ed157 ("Bluetooth: l2cap: Check encryption key size on incoming connection")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e2e3044c1 ]
Device flags could be updated in the meantime while MGMT_OP_ADD_DEVICE
is pending on hci_update_passive_scan_sync so instead of setting the
current_flags as cmd->user_data just do a lookup using
hci_conn_params_lookup and use the latest stored flags.
Fixes: a182d9c84f ("Bluetooth: MGMT: Fix Add Device to responding before completing")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3908feb1bd ]
Copy timestamp too when allocating new skb for received fragment.
Fixes missing RX timestamps with fragmentation.
Fixes: 4d7ea8ee90 ("Bluetooth: L2CAP: Fix handling fragmented length")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 024421cf39 ]
BIG Create Sync requires the command to just generates a status so this
makes use of __hci_cmd_sync_status_sk to wait for
HCI_EVT_LE_BIG_SYNC_ESTABLISHED, also because of this chance it is not
longer necessary to use a custom method to serialize the process of
creating the BIG sync since the cmd_work_sync itself ensures only one
command would be pending which now awaits for
HCI_EVT_LE_BIG_SYNC_ESTABLISHED before proceeding to next connection.
Fixes: 42ecf19471 ("Bluetooth: ISO: Do not emit LE BIG Create Sync if previous is pending")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d0417e4e1 ]
Broadcast Receiver requires creating PA sync but the command just
generates a status so this makes use of __hci_cmd_sync_status_sk to wait
for HCI_EV_LE_PA_SYNC_ESTABLISHED, also because of this chance it is not
longer necessary to use a custom method to serialize the process of
creating the PA sync since the cmd_work_sync itself ensures only one
command would be pending which now awaits for
HCI_EV_LE_PA_SYNC_ESTABLISHED before proceeding to next connection.
Fixes: 4a5e0ba686 ("Bluetooth: ISO: Do not emit LE PA Create Sync if previous is pending")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25ab2db3e6 ]
This removes the kzalloc memory allocation inside critical section in
create_pa_sync, fixing the following message that appears when the kernel
is compiled with CONFIG_DEBUG_ATOMIC_SLEEP enabled:
BUG: sleeping function called from invalid context at
include/linux/sched/mm.h:321
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stable-dep-of: 6d0417e4e1 ("Bluetooth: hci_conn: Fix not setting conn_timeout for Broadcast Receiver")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e2e49e2141 upstream.
This is required for passing PTS test cases:
- L2CAP/COS/CED/BI-14-C
Multiple Signaling Command in one PDU, Data Truncated, BR/EDR,
Connection Request
- L2CAP/COS/CED/BI-15-C
Multiple Signaling Command in one PDU, Data Truncated, BR/EDR,
Disconnection Request
The test procedure defined in L2CAP.TS.p39 for both tests is:
1. The Lower Tester sends a C-frame to the IUT with PDU Length set
to 8 and Channel ID set to the correct signaling channel for the
logical link. The Information payload contains one L2CAP_ECHO_REQ
packet with Data Length set to 0 with 0 octets of echo data and
one command packet and Data Length set as specified in Table 4.6
and the correct command data.
2. The IUT sends an L2CAP_ECHO_RSP PDU to the Lower Tester.
3. Perform alternative 3A, 3B, 3C, or 3D depending on the IUT’s
response.
Alternative 3A (IUT terminates the link):
3A.1 The IUT terminates the link.
3A.2 The test ends with a Pass verdict.
Alternative 3B (IUT discards the frame):
3B.1 The IUT does not send a reply to the Lower Tester.
Alternative 3C (IUT rejects PDU):
3C.1 The IUT sends an L2CAP_COMMAND_REJECT_RSP PDU to the
Lower Tester.
Alternative 3D (Any other IUT response):
3D.1 The Upper Tester issues a warning and the test ends.
4. The Lower Tester sends a C-frame to the IUT with PDU Length set
to 4 and Channel ID set to the correct signaling channel for the
logical link. The Information payload contains Data Length set to
0 with an L2CAP_ECHO_REQ packet with 0 octets of echo data.
5. The IUT sends an L2CAP_ECHO_RSP PDU to the Lower Tester.
With expected outcome:
In Steps 2 and 5, the IUT responds with an L2CAP_ECHO_RSP.
In Step 3A.1, the IUT terminates the link.
In Step 3B.1, the IUT does not send a reply to the Lower Tester.
In Step 3C.1, the IUT rejects the PDU.
In Step 3D.1, the IUT sends any valid response.
Currently PTS fails with the following logs:
Failed to receive ECHO RESPONSE.
And HCI logs:
> ACL Data RX: Handle 11 flags 0x02 dlen 20
L2CAP: Information Response (0x0b) ident 2 len 12
Type: Fixed channels supported (0x0003)
Result: Success (0x0000)
Channels: 0x000000000000002e
L2CAP Signaling (BR/EDR)
Connectionless reception
AMP Manager Protocol
L2CAP Signaling (LE)
> ACL Data RX: Handle 11 flags 0x02 dlen 13
frame too long
08 01 00 00 08 02 01 00 aa .........
Cc: stable@vger.kernel.org
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit eb73b5a915 ]
This fixes sending MGMT_EV_DEVICE_FOUND for invalid address
(00:00:00:00:00:00) which is a regression introduced by
a2ec905d1e ("Bluetooth: fix kernel oops in store_pending_adv_report")
since in the attempt to skip storing data for extended advertisement it
actually made the code to skip the entire if statement supposed to send
MGMT_EV_DEVICE_FOUND without attempting to use the last_addr_adv which
is garanteed to be invalid for extended advertisement since we never
store anything on it.
Link: https://github.com/bluez/bluez/issues/1157
Link: https://github.com/bluez/bluez/issues/1149#issuecomment-2767215658
Fixes: a2ec905d1e ("Bluetooth: fix kernel oops in store_pending_adv_report")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 127881334e ]
Some fake controllers cannot be initialized because they return a smaller
report than expected for READ_PAGE_SCAN_TYPE.
Signed-off-by: Pedro Nishiyama <nishiyama.pedro@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff26b2dd65 ]
Some fake controllers cannot be initialized because they return a smaller
report than expected for READ_VOICE_SETTING.
Signed-off-by: Pedro Nishiyama <nishiyama.pedro@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72d061ee63 ]
The chan_alloc_skb_cb() function is supposed to return error pointers on
error. Returning NULL will lead to a NULL dereference.
Fixes: 6b8d4a6a03 ("Bluetooth: 6LoWPAN: Use connected oriented channel instead of fixed one")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0bdd889715 ]
Passive scanning shall only be enabled when disconnecting LE links,
otherwise it may start result in triggering scanning when e.g. an ISO
link disconnects:
> HCI Event: LE Meta Event (0x3e) plen 29
LE Connected Isochronous Stream Established (0x19)
Status: Success (0x00)
Connection Handle: 257
CIG Synchronization Delay: 0 us (0x000000)
CIS Synchronization Delay: 0 us (0x000000)
Central to Peripheral Latency: 10000 us (0x002710)
Peripheral to Central Latency: 10000 us (0x002710)
Central to Peripheral PHY: LE 2M (0x02)
Peripheral to Central PHY: LE 2M (0x02)
Number of Subevents: 1
Central to Peripheral Burst Number: 1
Peripheral to Central Burst Number: 1
Central to Peripheral Flush Timeout: 2
Peripheral to Central Flush Timeout: 2
Central to Peripheral MTU: 320
Peripheral to Central MTU: 160
ISO Interval: 10.00 msec (0x0008)
...
> HCI Event: Disconnect Complete (0x05) plen 4
Status: Success (0x00)
Handle: 257
Reason: Remote User Terminated Connection (0x13)
< HCI Command: LE Set Extended Scan Enable (0x08|0x0042) plen 6
Extended scan: Enabled (0x01)
Filter duplicates: Enabled (0x01)
Duration: 0 msec (0x0000)
Period: 0.00 sec (0x0000)
Fixes: 9fcb18ef3a ("Bluetooth: Introduce LE auto connect options")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b25120e1d5 ]
L2CAP_ECRED_CONN_RSP needs to respond DCID in the same order received as
SCID but the order is reversed due to use of list_add which actually
prepend channels to the list so the response is reversed:
> ACL Data RX: Handle 16 flags 0x02 dlen 26
LE L2CAP: Enhanced Credit Connection Request (0x17) ident 2 len 18
PSM: 39 (0x0027)
MTU: 256
MPS: 251
Credits: 65535
Source CID: 116
Source CID: 117
Source CID: 118
Source CID: 119
Source CID: 120
< ACL Data TX: Handle 16 flags 0x00 dlen 26
LE L2CAP: Enhanced Credit Connection Response (0x18) ident 2 len 18
MTU: 517
MPS: 247
Credits: 3
Result: Connection successful (0x0000)
Destination CID: 68
Destination CID: 67
Destination CID: 66
Destination CID: 65
Destination CID: 64
Also make sure the response don't include channels that are not on
BT_CONNECT2 since the chan->ident can be set to the same value as in the
following trace:
< ACL Data TX: Handle 16 flags 0x00 dlen 12
LE L2CAP: LE Flow Control Credit (0x16) ident 6 len 4
Source CID: 64
Credits: 1
...
> ACL Data RX: Handle 16 flags 0x02 dlen 18
LE L2CAP: Enhanced Credit Connection Request (0x17) ident 6 len 10
PSM: 39 (0x0027)
MTU: 517
MPS: 251
Credits: 255
Source CID: 70
< ACL Data TX: Handle 16 flags 0x00 dlen 20
LE L2CAP: Enhanced Credit Connection Response (0x18) ident 6 len 12
MTU: 517
MPS: 247
Credits: 3
Result: Connection successful (0x0000)
Destination CID: 64
Destination CID: 68
Closes: https://github.com/bluez/bluez/issues/1094
Fixes: 9aa9d9473f ("Bluetooth: L2CAP: Fix responding with wrong PDU type")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5c61419e02 upstream.
One of the possible ways to enable the input MTU auto-selection for L2CAP
connections is supposed to be through passing a special "0" value for it
as a socket option. Commit [1] added one of those into avdtp. However, it
simply wouldn't work because the kernel still treats the specified value
as invalid and denies the setting attempt. Recorded BlueZ logs include the
following:
bluetoothd[496]: profiles/audio/avdtp.c:l2cap_connect() setsockopt(L2CAP_OPTIONS): Invalid argument (22)
[1]: ae5be371a9
Found by Linux Verification Center (linuxtesting.org).
Fixes: 4b6e228e29 ("Bluetooth: Auto tune if input MTU is set to 0")
Cc: stable@vger.kernel.org
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f397409f8 upstream.
A NULL sock pointer is passed into l2cap_sock_alloc() when it is called
from l2cap_sock_new_connection_cb() and the error handling paths should
also be aware of it.
Seemingly a more elegant solution would be to swap bt_sock_alloc() and
l2cap_chan_create() calls since they are not interdependent to that moment
but then l2cap_chan_create() adds the soon to be deallocated and still
dummy-initialized channel to the global list accessible by many L2CAP
paths. The channel would be removed from the list in short period of time
but be a bit more straight-forward here and just check for NULL instead of
changing the order of function calls.
Found by Linux Verification Center (linuxtesting.org) with SVACE static
analysis tool.
Fixes: 7c4f78cdb8 ("Bluetooth: L2CAP: do not leave dangling sk pointer on error in l2cap_sock_create()")
Cc: stable@vger.kernel.org
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 67dba2c28f ]
Use usb_autopm_get_interface() and usb_autopm_put_interface()
in btmtk_usb_shutdown(), it could send func ctrl after enabling
autosuspend.
Bluetooth: btmtk_usb_hci_wmt_sync() hci0: Execution of wmt command
timed out
Bluetooth: btmtk_usb_shutdown() hci0: Failed to send wmt func ctrl
(-110)
Fixes: 5c5e8c52e3 ("Bluetooth: btmtk: move btusb_mtk_[setup, shutdown] to btmtk.c")
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
