[ Upstream commit 278033a225 ]
When CONFIG_TMPFS is enabled, the initial root filesystem is a tmpfs.
By default, a tmpfs mount is limited to using 50% of the available RAM
for its content. This can be problematic in memory-constrained
environments, particularly during a kdump capture.
In a kdump scenario, the capture kernel boots with a limited amount of
memory specified by the 'crashkernel' parameter. If the initramfs is
large, it may fail to unpack into the tmpfs rootfs due to insufficient
space. This is because to get X MB of usable space in tmpfs, 2*X MB of
memory must be available for the mount. This leads to an OOM failure
during the early boot process, preventing a successful crash dump.
This patch introduces a new kernel command-line parameter,
initramfs_options, which allows passing specific mount options directly
to the rootfs when it is first mounted. This gives users control over
the rootfs behavior.
For example, a user can now specify initramfs_options=size=75% to allow
the tmpfs to use up to 75% of the available memory. This can
significantly reduce the memory pressure for kdump.
Consider a practical example:
To unpack a 48MB initramfs, the tmpfs needs 48MB of usable space. With
the default 50% limit, this requires a memory pool of 96MB to be
available for the tmpfs mount. The total memory requirement is therefore
approximately: 16MB (vmlinuz) + 48MB (loaded initramfs) + 48MB (unpacked
kernel) + 96MB (for tmpfs) + 12MB (runtime overhead) ≈ 220MB.
By using initramfs_options=size=75%, the memory pool required for the
48MB tmpfs is reduced to 48MB / 0.75 = 64MB. This reduces the total
memory requirement by 32MB (96MB - 64MB), allowing the kdump to succeed
with a smaller crashkernel size, such as 192MB.
An alternative approach of reusing the existing rootflags parameter was
considered. However, a new, dedicated initramfs_options parameter was
chosen to avoid altering the current behavior of rootflags (which
applies to the final root filesystem) and to prevent any potential
regressions.
Also add documentation for the new kernel parameter "initramfs_options"
This approach is inspired by prior discussions and patches on the topic.
Ref: https://www.lightofdawn.org/blog/?viewDetailed=00128
Ref: https://landley.net/notes-2015.html#01-01-2015
Ref: https://lkml.org/lkml/2021/6/29/783
Ref: https://www.kernel.org/doc/html/latest/filesystems/ramfs-rootfs-initramfs.html#what-is-rootfs
Signed-off-by: Lichen Liu <lichliu@redhat.com>
Link: https://lore.kernel.org/20250815121459.3391223-1-lichliu@redhat.com
Tested-by: Rob Landley <rob@landley.net>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit 7adb96687c which is
commit 98fdaeb296 upstream.
commit 7adb96687c ("x86/bugs: Make spectre user default depend on
MITIGATION_SPECTRE_V2") depends on commit 72c70f480a ("x86/bugs: Add
a separate config for Spectre V2"), which introduced
MITIGATION_SPECTRE_V2.
commit 72c70f480a ("x86/bugs: Add a separate config for Spectre V2")
never landed in stable tree, thus, stable tree doesn't have
MITIGATION_SPECTRE_V2, that said, commit 7adb96687c ("x86/bugs: Make
spectre user default depend on MITIGATION_SPECTRE_V2") has no value if
the dependecy was not applied.
Revert commit 7adb96687c ("x86/bugs: Make spectre user default
depend on MITIGATION_SPECTRE_V2") in stable kernel which landed in in
5.4.294, 5.10.238, 5.15.185, 6.1.141 and 6.6.93 stable versions.
Cc: David.Kaplan@amd.com
Cc: peterz@infradead.org
Cc: pawan.kumar.gupta@linux.intel.com
Cc: mingo@kernel.org
Cc: brad.spengler@opensrcsec.com
Cc: stable@vger.kernel.org # 6.6 6.1 5.15 5.10 5.4
Reported-by: Brad Spengler <brad.spengler@opensrcsec.com>
Reported-by: Salvatore Bonaccorso <carnil@debian.org>
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 98fdaeb296 ]
Change the default value of spectre v2 in user mode to respect the
CONFIG_MITIGATION_SPECTRE_V2 config option.
Currently, user mode spectre v2 is set to auto
(SPECTRE_V2_USER_CMD_AUTO) by default, even if
CONFIG_MITIGATION_SPECTRE_V2 is disabled.
Set the spectre_v2 value to auto (SPECTRE_V2_USER_CMD_AUTO) if the
Spectre v2 config (CONFIG_MITIGATION_SPECTRE_V2) is enabled, otherwise
set the value to none (SPECTRE_V2_USER_CMD_NONE).
Important to say the command line argument "spectre_v2_user" overwrites
the default value in both cases.
When CONFIG_MITIGATION_SPECTRE_V2 is not set, users have the flexibility
to opt-in for specific mitigations independently. In this scenario,
setting spectre_v2= will not enable spectre_v2_user=, and command line
options spectre_v2_user and spectre_v2 are independent when
CONFIG_MITIGATION_SPECTRE_V2=n.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Acked-by: Josh Poimboeuf <jpoimboe@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: David Kaplan <David.Kaplan@amd.com>
Link: https://lore.kernel.org/r/20241031-x86_bugs_last_v2-v2-2-b7ff1dab840e@debian.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit facd226f7e upstream.
When retpoline mitigation is enabled for spectre-v2, enabling
call-depth-tracking and RSB stuffing also mitigates ITS. Add cmdline option
indirect_target_selection=stuff to allow enabling RSB stuffing mitigation.
When retpoline mitigation is not enabled, =stuff option is ignored, and
default mitigation for ITS is deployed.
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@kernel.org>
Reviewed-by: Alexandre Chartre <alexandre.chartre@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2665281a07 upstream.
Ice Lake generation CPUs are not affected by guest/host isolation part of
ITS. If a user is only concerned about KVM guests, they can now choose a
new cmdline option "vmexit" that will not deploy the ITS mitigation when
CPU is not affected by guest/host isolation. This saves the performance
overhead of ITS mitigation on Ice Lake gen CPUs.
When "vmexit" option selected, if the CPU is affected by ITS guest/host
isolation, the default ITS mitigation is deployed.
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@kernel.org>
Reviewed-by: Alexandre Chartre <alexandre.chartre@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4818881c4 upstream.
Indirect Target Selection (ITS) is a bug in some pre-ADL Intel CPUs with
eIBRS. It affects prediction of indirect branch and RETs in the
lower half of cacheline. Due to ITS such branches may get wrongly predicted
to a target of (direct or indirect) branch that is located in the upper
half of the cacheline.
Scope of impact
===============
Guest/host isolation
--------------------
When eIBRS is used for guest/host isolation, the indirect branches in the
VMM may still be predicted with targets corresponding to branches in the
guest.
Intra-mode
----------
cBPF or other native gadgets can be used for intra-mode training and
disclosure using ITS.
User/kernel isolation
---------------------
When eIBRS is enabled user/kernel isolation is not impacted.
Indirect Branch Prediction Barrier (IBPB)
-----------------------------------------
After an IBPB, indirect branches may be predicted with targets
corresponding to direct branches which were executed prior to IBPB. This is
mitigated by a microcode update.
Add cmdline parameter indirect_target_selection=off|on|force to control the
mitigation to relocate the affected branches to an ITS-safe thunk i.e.
located in the upper half of cacheline. Also add the sysfs reporting.
When retpoline mitigation is deployed, ITS safe-thunks are not needed,
because retpoline sequence is already ITS-safe. Similarly, when call depth
tracking (CDT) mitigation is deployed (retbleed=stuff), ITS safe return
thunk is not used, as CDT prevents RSB-underflow.
To not overcomplicate things, ITS mitigation is not supported with
spectre-v2 lfence;jmp mitigation. Moreover, it is less practical to deploy
lfence;jmp mitigation on ITS affected parts anyways.
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@kernel.org>
Reviewed-by: Alexandre Chartre <alexandre.chartre@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9407bda845 upstream
Applying microcode late can be fatal for the running kernel when the
update changes functionality which is in use already in a non-compatible
way, e.g. by removing a CPUID bit.
There is no way for admins which do not have access to the vendors deep
technical support to decide whether late loading of such a microcode is
safe or not.
Intel has added a new field to the microcode header which tells the
minimal microcode revision which is required to be active in the CPU in
order to be safe.
Provide infrastructure for handling this in the core code and a command
line switch which allows to enforce it.
If the update is considered safe the kernel is not tainted and the annoying
warning message not emitted. If it's enforced and the currently loaded
microcode revision is not safe for late loading then the load is aborted.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20231017211724.079611170@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b5487aefb upstream.
Setting encryption as required in security flags was broken.
For example (to require all mounts to be encrypted by setting):
"echo 0x400c5 > /proc/fs/cifs/SecurityFlags"
Would return "Invalid argument" and log "Unsupported security flags"
This patch fixes that (e.g. allowing overriding the default for
SecurityFlags 0x00c5, including 0x40000 to require seal, ie
SMB3.1.1 encryption) so now that works and forces encryption
on subsequent mounts.
Acked-by: Bharath SM <bharathsm@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2ed08e4bc5 ]
On a 8-socket server the TSC is wrongly marked as 'unstable' and disabled
during boot time on about one out of 120 boot attempts:
clocksource: timekeeping watchdog on CPU227: wd-tsc-wd excessive read-back delay of 153560ns vs. limit of 125000ns,
wd-wd read-back delay only 11440ns, attempt 3, marking tsc unstable
tsc: Marking TSC unstable due to clocksource watchdog
TSC found unstable after boot, most likely due to broken BIOS. Use 'tsc=unstable'.
sched_clock: Marking unstable (119294969739, 159204297)<-(125446229205, -5992055152)
clocksource: Checking clocksource tsc synchronization from CPU 319 to CPUs 0,99,136,180,210,542,601,896.
clocksource: Switched to clocksource hpet
The reason is that for platform with a large number of CPUs, there are
sporadic big or huge read latencies while reading the watchog/clocksource
during boot or when system is under stress work load, and the frequency and
maximum value of the latency goes up with the number of online CPUs.
The cCurrent code already has logic to detect and filter such high latency
case by reading the watchdog twice and checking the two deltas. Due to the
randomness of the latency, there is a low probabilty that the first delta
(latency) is big, but the second delta is small and looks valid. The
watchdog code retries the readouts by default twice, which is not
necessarily sufficient for systems with a large number of CPUs.
There is a command line parameter 'max_cswd_read_retries' which allows to
increase the number of retries, but that's not user friendly as it needs to
be tweaked per system. As the number of required retries is proportional to
the number of online CPUs, this parameter can be calculated at runtime.
Scale and enlarge the number of retries according to the number of online
CPUs and remove the command line parameter completely.
[ tglx: Massaged change log and comments ]
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Jin Wang <jin1.wang@intel.com>
Tested-by: Paul E. McKenney <paulmck@kernel.org>
Reviewed-by: Waiman Long <longman@redhat.com>
Reviewed-by: Paul E. McKenney <paulmck@kernel.org>
Link: https://lore.kernel.org/r/20240221060859.1027450-1-feng.tang@intel.com
Stable-dep-of: f2655ac2c0 ("clocksource: Fix brown-bag boolean thinko in cs_watchdog_read()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b88f55389a upstream.
The kernel sleep profile is no longer working due to a recursive locking
bug introduced by commit 42a20f86dc ("sched: Add wrapper for get_wchan()
to keep task blocked")
Booting with the 'profile=sleep' kernel command line option added or
executing
# echo -n sleep > /sys/kernel/profiling
after boot causes the system to lock up.
Lockdep reports
kthreadd/3 is trying to acquire lock:
ffff93ac82e08d58 (&p->pi_lock){....}-{2:2}, at: get_wchan+0x32/0x70
but task is already holding lock:
ffff93ac82e08d58 (&p->pi_lock){....}-{2:2}, at: try_to_wake_up+0x53/0x370
with the call trace being
lock_acquire+0xc8/0x2f0
get_wchan+0x32/0x70
__update_stats_enqueue_sleeper+0x151/0x430
enqueue_entity+0x4b0/0x520
enqueue_task_fair+0x92/0x6b0
ttwu_do_activate+0x73/0x140
try_to_wake_up+0x213/0x370
swake_up_locked+0x20/0x50
complete+0x2f/0x40
kthread+0xfb/0x180
However, since nobody noticed this regression for more than two years,
let's remove 'profile=sleep' support based on the assumption that nobody
needs this functionality.
Fixes: 42a20f86dc ("sched: Add wrapper for get_wchan() to keep task blocked")
Cc: stable@vger.kernel.org # v5.16+
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d2346e2836 upstream.
If you try to set /proc/fs/cifs/SecurityFlags to 1 it
will set them to CIFSSEC_MUST_NTLMV2 which no longer is
relevant (the less secure ones like lanman have been removed
from cifs.ko) and is also missing some flags (like for
signing and encryption) and can even cause mount to fail,
so change this to set it to Kerberos in this case.
Also change the description of the SecurityFlags to remove mention
of flags which are no longer supported.
Cc: stable@vger.kernel.org
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ce0abef6a1 ]
Explicitly disallow enabling mitigations at runtime for kernels that were
built with CONFIG_CPU_MITIGATIONS=n, as some architectures may omit code
entirely if mitigations are disabled at compile time.
E.g. on x86, a large pile of Kconfigs are buried behind CPU_MITIGATIONS,
and trying to provide sane behavior for retroactively enabling mitigations
is extremely difficult, bordering on impossible. E.g. page table isolation
and call depth tracking require build-time support, BHI mitigations will
still be off without additional kernel parameters, etc.
[ bp: Touchups. ]
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20240420000556.2645001-3-seanjc@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12a686c2e7 ]
This patch adds /proc/sys/net/core/mem_pcpu_rsv sysctl file,
to make SK_MEMORY_PCPU_RESERV tunable.
Commit 3cd3399dd7 ("net: implement per-cpu reserves for
memory_allocated") introduced per-cpu forward alloc cache:
"Implement a per-cpu cache of +1/-1 MB, to reduce number
of changes to sk->sk_prot->memory_allocated, which
would otherwise be cause of false sharing."
sk_prot->memory_allocated points to global atomic variable:
atomic_long_t tcp_memory_allocated ____cacheline_aligned_in_smp;
If increasing the per-cpu cache size from 1MB to e.g. 16MB,
changes to sk->sk_prot->memory_allocated can be further reduced.
Performance may be improved on system with many cores.
Signed-off-by: Adam Li <adamli@os.amperecomputing.com>
Reviewed-by: Christoph Lameter (Ampere) <cl@linux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 3584718cf2 ("net: fix sk_memory_allocated_{add|sub} vs softirqs")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a1ccf0c72 ]
This patch introduces a new USB quirk,
USB_QUIRK_SHORT_SET_ADDRESS_REQ_TIMEOUT, which modifies the timeout value
for the SET_ADDRESS request. The standard timeout for USB request/command
is 5000 ms, as recommended in the USB 3.2 specification (section 9.2.6.1).
However, certain scenarios, such as connecting devices through an APTIV
hub, can lead to timeout errors when the device enumerates as full speed
initially and later switches to high speed during chirp negotiation.
In such cases, USB analyzer logs reveal that the bus suspends for
5 seconds due to incorrect chirp parsing and resumes only after two
consecutive timeout errors trigger a hub driver reset.
Packet(54) Dir(?) Full Speed J(997.100 us) Idle( 2.850 us)
_______| Time Stamp(28 . 105 910 682)
_______|_____________________________________________________________Ch0
Packet(55) Dir(?) Full Speed J(997.118 us) Idle( 2.850 us)
_______| Time Stamp(28 . 106 910 632)
_______|_____________________________________________________________Ch0
Packet(56) Dir(?) Full Speed J(399.650 us) Idle(222.582 us)
_______| Time Stamp(28 . 107 910 600)
_______|_____________________________________________________________Ch0
Packet(57) Dir Chirp J( 23.955 ms) Idle(115.169 ms)
_______| Time Stamp(28 . 108 532 832)
_______|_____________________________________________________________Ch0
Packet(58) Dir(?) Full Speed J (Suspend)( 5.347 sec) Idle( 5.366 us)
_______| Time Stamp(28 . 247 657 600)
_______|_____________________________________________________________Ch0
This 5-second delay in device enumeration is undesirable, particularly
in automotive applications where quick enumeration is crucial
(ideally within 3 seconds).
The newly introduced quirks provide the flexibility to align with a
3-second time limit, as required in specific contexts like automotive
applications.
By reducing the SET_ADDRESS request timeout to 500 ms, the
system can respond more swiftly to errors, initiate rapid recovery, and
ensure efficient device enumeration. This change is vital for scenarios
where rapid smartphone enumeration and screen projection are essential.
To use the quirk, please write "vendor_id:product_id:p" to
/sys/bus/usb/drivers/hub/module/parameter/quirks
For example,
echo "0x2c48:0x0132:p" > /sys/bus/usb/drivers/hub/module/parameters/quirks"
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20231027152029.104363-2-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 95a6ccbdc7 upstream.
BHI mitigation mode spectre_bhi=auto does not deploy the software
mitigation by default. In a cloud environment, it is a likely scenario
where userspace is trusted but the guests are not trusted. Deploying
system wide mitigation in such cases is not desirable.
Update the auto mode to unconditionally mitigate against malicious
guests. Deploy the software sequence at VMexit in auto mode also, when
hardware mitigation is not available. Unlike the force =on mode,
software sequence is not deployed at syscalls in auto mode.
Suggested-by: Alexandre Chartre <alexandre.chartre@oracle.com>
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexandre Chartre <alexandre.chartre@oracle.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec9404e40e upstream.
Branch history clearing software sequences and hardware control
BHI_DIS_S were defined to mitigate Branch History Injection (BHI).
Add cmdline spectre_bhi={on|off|auto} to control BHI mitigation:
auto - Deploy the hardware mitigation BHI_DIS_S, if available.
on - Deploy the hardware mitigation BHI_DIS_S, if available,
otherwise deploy the software sequence at syscall entry and
VMexit.
off - Turn off BHI mitigation.
The default is auto mode which does not deploy the software sequence
mitigation. This is because of the hardening done in the syscall
dispatch path, which is the likely target of BHI.
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexandre Chartre <alexandre.chartre@oracle.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8076fcde01 upstream.
RFDS is a CPU vulnerability that may allow userspace to infer kernel
stale data previously used in floating point registers, vector registers
and integer registers. RFDS only affects certain Intel Atom processors.
Intel released a microcode update that uses VERW instruction to clear
the affected CPU buffers. Unlike MDS, none of the affected cores support
SMT.
Add RFDS bug infrastructure and enable the VERW based mitigation by
default, that clears the affected buffers just before exiting to
userspace. Also add sysfs reporting and cmdline parameter
"reg_file_data_sampling" to control the mitigation.
For details see:
Documentation/admin-guide/hw-vuln/reg-file-data-sampling.rst
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 94b3f0b5af ]
The CSD lock seems to get stuck in 2 "modes". When it gets stuck
temporarily, it usually gets released in a few seconds, and sometimes
up to one or two minutes.
If the CSD lock stays stuck for more than several minutes, it never
seems to get unstuck, and gradually more and more things in the system
end up also getting stuck.
In the latter case, we should just give up, so the system can dump out
a little more information about what went wrong, and, with panic_on_oops
and a kdump kernel loaded, dump a whole bunch more information about what
might have gone wrong. In addition, there is an smp.panic_on_ipistall
kernel boot parameter that by default retains the old behavior, but when
set enables the panic after the CSD lock has been stuck for more than
the specified number of milliseconds, as in 300,000 for five minutes.
[ paulmck: Apply Imran Khan feedback. ]
[ paulmck: Apply Leonardo Bras feedback. ]
Link: https://lore.kernel.org/lkml/bc7cc8b0-f587-4451-8bcd-0daae627bcc7@paulmck-laptop/
Signed-off-by: Rik van Riel <riel@surriel.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Reviewed-by: Imran Khan <imran.f.khan@oracle.com>
Reviewed-by: Leonardo Bras <leobras@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Valentin Schneider <vschneid@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc6306ad5b ]
The SRSO default safe-ret mitigation is reported as "mitigated" even if
microcode hasn't been updated. That's wrong because userspace may still
be vulnerable to SRSO attacks due to IBPB not flushing branch type
predictions.
Report the safe-ret + !microcode case as vulnerable.
Also report the microcode-only case as vulnerable as it leaves the
kernel open to attacks.
Fixes: fb3bd914b3 ("x86/srso: Add a Speculative RAS Overflow mitigation")
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/a8a14f97d1b0e03ec255c81637afdf4cf0ae9c99.1693889988.git.jpoimboe@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commits 86327e8eb9 ("memcg: drop kmem.limit_in_bytes") and
partially reverts 58056f7750 ("memcg, kmem: further deprecate
kmem.limit_in_bytes") which have incrementally removed support for the
kernel memory accounting hard limit. Unfortunately it has turned out that
there is still userspace depending on the existence of
memory.kmem.limit_in_bytes [1]. The underlying functionality is not
really required but the non-existent file just confuses the userspace
which fails in the result. The patch to fix this on the userspace side
has been submitted but it is hard to predict how it will propagate through
the maze of 3rd party consumers of the software.
Now, reverting alone 86327e8eb9 is not an option because there is
another set of userspace which cannot cope with ENOTSUPP returned when
writing to the file. Therefore we have to go and revisit 58056f7750 as
well. There are two ways to go ahead. Either we give up on the
deprecation and fully revert 58056f7750 as well or we can keep
kmem.limit_in_bytes but make the write a noop and warn about the fact.
This should work for both known breaking workloads which depend on the
existence but do not depend on the hard limit enforcement.
Note to backporters to stable trees. a8c49af3be ("memcg: add per-memcg
total kernel memory stat") introduced in 4.18 has added memcg_account_kmem
so the accounting is not done by obj_cgroup_charge_pages directly for v1
anymore. Prior kernels need to add it explicitly (thanks to Johannes for
pointing this out).
[akpm@linux-foundation.org: fix build - remove unused local]
Link: http://lkml.kernel.org/r/20230920081101.GA12096@linuxonhyperv3.guj3yctzbm1etfxqx2vob5hsef.xx.internal.cloudapp.net [1]
Link: https://lkml.kernel.org/r/ZRE5VJozPZt9bRPy@dhcp22.suse.cz
Fixes: 86327e8eb9 ("memcg: drop kmem.limit_in_bytes")
Fixes: 58056f7750 ("memcg, kmem: further deprecate kmem.limit_in_bytes")
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jeremi Piotrowski <jpiotrowski@linux.microsoft.com>
Cc: Muchun Song <muchun.song@linux.dev>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Cc: Tejun heo <tj@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Pull perf tools updates from Arnaldo Carvalho de Melo:
"perf tools maintainership:
- Add git information for perf-tools and perf-tools-next trees and
branches to the MAINTAINERS file. That is where development now
takes place and myself and Namhyung Kim have write access, more
people to come as we emulate other maintainer groups.
perf record:
- Record kernel data maps when 'perf record --data' is used, so that
global variables can be resolved and used in tools that do data
profiling.
perf trace:
- Remove the old, experimental support for BPF events in which a .c
file was passed as an event: "perf trace -e hello.c" to then get
compiled and loaded.
The only known usage for that, that shipped with the kernel as an
example for such events, augmented the raw_syscalls tracepoints and
was converted to a libbpf skeleton, reusing all the user space
components and the BPF code connected to the syscalls.
In the end just the way to glue the BPF part and the user space
type beautifiers changed, now being performed by libbpf skeletons.
The next step is to use BTF to do pretty printing of all syscall
types, as discussed with Alan Maguire and others.
Now, on a perf built with BUILD_BPF_SKEL=1 we get most if not all
path/filenames/strings, some of the networking data structures,
perf_event_attr, etc, i.e. systemwide tracing of nanosleep calls
and perf_event_open syscalls while 'perf stat' runs 'sleep' for 5
seconds:
# perf trace -a -e *nanosleep,perf* perf stat -e cycles,instructions sleep 5
0.000 ( 9.034 ms): perf/327641 perf_event_open(attr_uptr: { type: 0 (PERF_TYPE_HARDWARE), size: 136, config: 0 (PERF_COUNT_HW_CPU_CYCLES), sample_type: IDENTIFIER, read_format: TOTAL_TIME_ENABLED|TOTAL_TIME_RUNNING, disabled: 1, inherit: 1, enable_on_exec: 1, exclude_guest: 1 }, pid: 327642 (perf), cpu: -1, group_fd: -1, flags: FD_CLOEXEC) = 3
9.039 ( 0.006 ms): perf/327641 perf_event_open(attr_uptr: { type: 0 (PERF_TYPE_HARDWARE), size: 136, config: 0x1 (PERF_COUNT_HW_INSTRUCTIONS), sample_type: IDENTIFIER, read_format: TOTAL_TIME_ENABLED|TOTAL_TIME_RUNNING, disabled: 1, inherit: 1, enable_on_exec: 1, exclude_guest: 1 }, pid: 327642 (perf-exec), cpu: -1, group_fd: -1, flags: FD_CLOEXEC) = 4
? ( ): gpm/991 ... [continued]: clock_nanosleep()) = 0
10.133 ( ): sleep/327642 clock_nanosleep(rqtp: { .tv_sec: 5, .tv_nsec: 0 }, rmtp: 0x7ffd36f83ed0) ...
? ( ): pool-gsd-smart/3051 ... [continued]: clock_nanosleep()) = 0
30.276 ( ): gpm/991 clock_nanosleep(rqtp: { .tv_sec: 2, .tv_nsec: 0 }, rmtp: 0x7ffcc6f73710) ...
223.215 (1000.430 ms): pool-gsd-smart/3051 clock_nanosleep(rqtp: { .tv_sec: 1, .tv_nsec: 0 }, rmtp: 0x7f6e7fffec90) = 0
30.276 (2000.394 ms): gpm/991 ... [continued]: clock_nanosleep()) = 0
1230.814 ( ): pool-gsd-smart/3051 clock_nanosleep(rqtp: { .tv_sec: 1, .tv_nsec: 0 }, rmtp: 0x7f6e7fffec90) ...
1230.814 (1000.404 ms): pool-gsd-smart/3051 ... [continued]: clock_nanosleep()) = 0
2030.886 ( ): gpm/991 clock_nanosleep(rqtp: { .tv_sec: 2, .tv_nsec: 0 }, rmtp: 0x7ffcc6f73710) ...
2237.709 (1000.153 ms): pool-gsd-smart/3051 clock_nanosleep(rqtp: { .tv_sec: 1, .tv_nsec: 0 }, rmtp: 0x7f6e7fffec90) = 0
? ( ): crond/1172 ... [continued]: clock_nanosleep()) = 0
3242.699 ( ): pool-gsd-smart/3051 clock_nanosleep(rqtp: { .tv_sec: 1, .tv_nsec: 0 }, rmtp: 0x7f6e7fffec90) ...
2030.886 (2000.385 ms): gpm/991 ... [continued]: clock_nanosleep()) = 0
3728.078 ( ): crond/1172 clock_nanosleep(rqtp: { .tv_sec: 60, .tv_nsec: 0 }, rmtp: 0x7ffe0971dcf0) ...
3242.699 (1000.158 ms): pool-gsd-smart/3051 ... [continued]: clock_nanosleep()) = 0
4031.409 ( ): gpm/991 clock_nanosleep(rqtp: { .tv_sec: 2, .tv_nsec: 0 }, rmtp: 0x7ffcc6f73710) ...
10.133 (5000.375 ms): sleep/327642 ... [continued]: clock_nanosleep()) = 0
Performance counter stats for 'sleep 5':
2,617,347 cycles
1,855,997 instructions # 0.71 insn per cycle
5.002282128 seconds time elapsed
0.000855000 seconds user
0.000852000 seconds sys
perf annotate:
- Building with binutils' libopcode now is opt-in (BUILD_NONDISTRO=1)
for licensing reasons, and we missed a build test on
tools/perf/tests makefile.
Since we now default to NDEBUG=1, we ended up segfaulting when
building with BUILD_NONDISTRO=1 because a needed initialization
routine was being "error checked" via an assert.
Fix it by explicitly checking the result and aborting instead if it
fails.
We better back propagate the error, but at least 'perf annotate' on
samples collected for a BPF program is back working when perf is
built with BUILD_NONDISTRO=1.
perf report/top:
- Add back TUI hierarchy mode header, that is seen when using 'perf
report/top --hierarchy'.
- Fix the number of entries for 'e' key in the TUI that was
preventing navigation of lines when expanding an entry.
perf report/script:
- Support cross platform register handling, allowing a perf.data file
collected on one architecture to have registers sampled correctly
displayed when analysis tools such as 'perf report' and 'perf
script' are used on a different architecture.
- Fix handling of event attributes in pipe mode, i.e. when one uses:
perf record -o - | perf report -i -
When no perf.data files are used.
- Handle files generated via pipe mode with a version of perf and
then read also via pipe mode with a different version of perf,
where the event attr record may have changed, use the record size
field to properly support this version mismatch.
perf probe:
- Accessing global variables from uprobes isn't supported, make the
error message state that instead of stating that some minimal
kernel version is needed to have that feature. This seems just a
tool limitation, the kernel probably has all that is needed.
perf tests:
- Fix a reference count related leak in the dlfilter v0 API where the
result of a thread__find_symbol_fb() is not matched with an
addr_location__exit() to drop the reference counts of the resolved
components (machine, thread, map, symbol, etc). Add a dlfilter test
to make sure that doesn't regresses.
- Lots of fixes for the 'perf test' written in shell script related
to problems found with the shellcheck utility.
- Fixes for 'perf test' shell scripts testing features enabled when
perf is built with BUILD_BPF_SKEL=1, such as 'perf stat' bpf
counters.
- Add perf record sample filtering test, things like the following
example, that gets implemented as a BPF filter attached to the
event:
# perf record -e task-clock -c 10000 --filter 'ip < 0xffffffff00000000'
- Improve the way the task_analyzer test checks if libtraceevent is
linked, using 'perf version --build-options' instead of the more
expensinve 'perf record -e "sched:sched_switch"'.
- Add support for riscv in the mmap-basic test. (This went as well
via the RiscV tree, same contents).
libperf:
- Implement riscv mmap support (This went as well via the RiscV tree,
same contents).
perf script:
- New tool that converts perf.data files to the firefox profiler
format so that one can use the visualizer at
https://profiler.firefox.com/. Done by Anup Sharma as part of this
year's Google Summer of Code.
One can generate the output and upload it to the web interface but
Anup also automated everything:
perf script gecko -F 99 -a sleep 60
- Support syscall name parsing on arm64.
- Print "cgroup" field on the same line as "comm".
perf bench:
- Add new 'uprobe' benchmark to measure the overhead of uprobes
with/without BPF programs attached to it.
- breakpoints are not available on power9, skip that test.
perf stat:
- Add #num_cpus_online literal to be used in 'perf stat' metrics, and
add this extra 'perf test' check that exemplifies its purpose:
TEST_ASSERT_VAL("#num_cpus_online",
expr__parse(&num_cpus_online, ctx, "#num_cpus_online") == 0);
TEST_ASSERT_VAL("#num_cpus", expr__parse(&num_cpus, ctx, "#num_cpus") == 0);
TEST_ASSERT_VAL("#num_cpus >= #num_cpus_online", num_cpus >= num_cpus_online);
Miscellaneous:
- Improve tool startup time by lazily reading PMU, JSON, sysfs data.
- Improve error reporting in the parsing of events, passing YYLTYPE
to error routines, so that the output can show were the parsing
error was found.
- Add 'perf test' entries to check the parsing of events
improvements.
- Fix various leak for things detected by -fsanitize=address, mostly
things that would be freed at tool exit, including:
- Free evsel->filter on the destructor.
- Allow tools to register a thread->priv destructor and use it in
'perf trace'.
- Free evsel->priv in 'perf trace'.
- Free string returned by synthesize_perf_probe_point() when the
caller fails to do all it needs.
- Adjust various compiler options to not consider errors some
warnings when building with broken headers found in things like
python, flex, bison, as we otherwise build with -Werror. Some for
gcc, some for clang, some for some specific version of those, some
for some specific version of flex or bison, or some specific
combination of these components, bah.
- Allow customization of clang options for BPF target, this helps
building on gentoo where there are other oddities where BPF targets
gets passed some compiler options intended for the native build, so
building with WERROR=0 helps while these oddities are fixed.
- Dont pass ERR_PTR() values to perf_session__delete() in 'perf top'
and 'perf lock', fixing some segfaults when handling some odd
failures.
- Add LTO build option.
- Fix format of unordered lists in the perf docs
(tools/perf/Documentation)
- Overhaul the bison files, using constructs such as YYNOMEM.
- Remove unused tokens from the bison .y files.
- Add more comments to various structs.
- A few LoongArch enablement patches.
Vendor events (JSON):
- Add JSON metrics for Yitian 710 DDR (aarch64). Things like:
EventName, BriefDescription
visible_window_limit_reached_rd, "At least one entry in read queue reaches the visible window limit.",
visible_window_limit_reached_wr, "At least one entry in write queue reaches the visible window limit.",
op_is_dqsosc_mpc , "A DQS Oscillator MPC command to DRAM.",
op_is_dqsosc_mrr , "A DQS Oscillator MRR command to DRAM.",
op_is_tcr_mrr , "A Temperature Compensated Refresh(TCR) MRR command to DRAM.",
- Add AmpereOne metrics (aarch64).
- Update N2 and V2 metrics (aarch64) and events using Arm telemetry
repo.
- Update scale units and descriptions of common topdown metrics on
aarch64. Things like:
- "MetricExpr": "stall_slot_frontend / (#slots * cpu_cycles)",
- "BriefDescription": "Frontend bound L1 topdown metric",
+ "MetricExpr": "100 * (stall_slot_frontend / (#slots * cpu_cycles))",
+ "BriefDescription": "This metric is the percentage of total slots that were stalled due to resource constraints in the frontend of the processor.",
- Update events for intel: meteorlake to 1.04, sapphirerapids to
1.15, Icelake+ metric constraints.
- Update files for the power10 platform"
* tag 'perf-tools-for-v6.6-1-2023-09-05' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools: (217 commits)
perf parse-events: Fix driver config term
perf parse-events: Fixes relating to no_value terms
perf parse-events: Fix propagation of term's no_value when cloning
perf parse-events: Name the two term enums
perf list: Don't print Unit for "default_core"
perf vendor events intel: Fix modifier in tma_info_system_mem_parallel_reads for skylake
perf dlfilter: Avoid leak in v0 API test use of resolve_address()
perf metric: Add #num_cpus_online literal
perf pmu: Remove str from perf_pmu_alias
perf parse-events: Make common term list to strbuf helper
perf parse-events: Minor help message improvements
perf pmu: Avoid uninitialized use of alias->str
perf jevents: Use "default_core" for events with no Unit
perf test stat_bpf_counters_cgrp: Enhance perf stat cgroup BPF counter test
perf test shell stat_bpf_counters: Fix test on Intel
perf test shell record_bpf_filter: Skip 6.2 kernel
libperf: Get rid of attr.id field
perf tools: Convert to perf_record_header_attr_id()
libperf: Add perf_record_header_attr_id()
perf tools: Handle old data in PERF_RECORD_ATTR
...
Pull io_uring fixes from Jens Axboe:
"A few fixes that should go into the 6.6-rc merge window:
- Fix for a regression this merge window caused by the SQPOLL
affinity patch, where we can race with SQPOLL thread shutdown and
cause an oops when trying to set affinity (Gabriel)
- Fix for a regression this merge window where fdinfo reading with
for a ring setup with IORING_SETUP_NO_SQARRAY will attempt to
deference the non-existing SQ ring array (me)
- Add the patch that allows more finegrained control over who can use
io_uring (Matteo)
- Locking fix for a regression added this merge window for IOPOLL
overflow (Pavel)
- IOPOLL fix for stable, breaking our loop if helper threads are
exiting (Pavel)
Also had a fix for unreaped iopoll requests from io-wq from Ming, but
we found an issue with that and hence it got reverted. Will get this
sorted for a future rc"
* tag 'io_uring-6.6-2023-09-08' of git://git.kernel.dk/linux:
Revert "io_uring: fix IO hang in io_wq_put_and_exit from do_exit()"
io_uring: fix unprotected iopoll overflow
io_uring: break out of iowq iopoll on teardown
io_uring: add a sysctl to disable io_uring system-wide
io_uring/fdinfo: only print ->sq_array[] if it's there
io_uring: fix IO hang in io_wq_put_and_exit from do_exit()
io_uring: Don't set affinity on a dying sqpoll thread
Introduce a new sysctl (io_uring_disabled) which can be either 0, 1, or
2. When 0 (the default), all processes are allowed to create io_uring
instances, which is the current behavior. When 1, io_uring creation is
disabled (io_uring_setup() will fail with -EPERM) for unprivileged
processes not in the kernel.io_uring_group group. When 2, calls to
io_uring_setup() fail with -EPERM regardless of privilege.
Signed-off-by: Matteo Rizzo <matteorizzo@google.com>
[JEM: modified to add io_uring_group]
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Link: https://lore.kernel.org/r/x49y1i42j1z.fsf@segfault.boston.devel.redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull workqueue updates from Tejun Heo:
- Unbound workqueues now support more flexible affinity scopes.
The default behavior is to soft-affine according to last level cache
boundaries. A work item queued from a given LLC is executed by a
worker running on the same LLC but the worker may be moved across
cache boundaries as the scheduler sees fit. On machines which
multiple L3 caches, which are becoming more popular along with
chiplet designs, this improves cache locality while not harming work
conservation too much.
Unbound workqueues are now also a lot more flexible in terms of
execution affinity. Differeing levels of affinity scopes are
supported and both the default and per-workqueue affinity settings
can be modified dynamically. This should help working around amny of
sub-optimal behaviors observed recently with asymmetric ARM CPUs.
This involved signficant restructuring of workqueue code. Nothing was
reported yet but there's some risk of subtle regressions. Should keep
an eye out.
- Rescuer workers now has more identifiable comms.
- workqueue.unbound_cpus added so that CPUs which can be used by
workqueue can be constrained early during boot.
- Now that all the in-tree users have been flushed out, trigger warning
if system-wide workqueues are flushed.
* tag 'wq-for-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (31 commits)
workqueue: fix data race with the pwq->stats[] increment
workqueue: Rename rescuer kworker
workqueue: Make default affinity_scope dynamically updatable
workqueue: Add "Affinity Scopes and Performance" section to documentation
workqueue: Implement non-strict affinity scope for unbound workqueues
workqueue: Add workqueue_attrs->__pod_cpumask
workqueue: Factor out need_more_worker() check and worker wake-up
workqueue: Factor out work to worker assignment and collision handling
workqueue: Add multiple affinity scopes and interface to select them
workqueue: Modularize wq_pod_type initialization
workqueue: Add tools/workqueue/wq_dump.py which prints out workqueue configuration
workqueue: Generalize unbound CPU pods
workqueue: Factor out clearing of workqueue-only attrs fields
workqueue: Factor out actual cpumask calculation to reduce subtlety in wq_update_pod()
workqueue: Initialize unbound CPU pods later in the boot
workqueue: Move wq_pod_init() below workqueue_init()
workqueue: Rename NUMA related names to use pod instead
workqueue: Rename workqueue_attrs->no_numa to ->ordered
workqueue: Make unbound workqueues to use per-cpu pool_workqueues
workqueue: Call wq_update_unbound_numa() on all CPUs in NUMA node on CPU hotplug
...
Pull cgroup updates from Tejun Heo:
- Per-cpu cpu usage stats are now tracked
This currently isn't printed out in the cgroupfs interface and can
only be accessed through e.g. BPF. Should decide on a not-too-ugly
way to show per-cpu stats in cgroupfs
- cpuset received some cleanups and prepatory patches for the pending
cpus.exclusive patchset which will allow cpuset partitions to be
created below non-partition parents, which should ease the management
of partition cpusets
- A lot of code and documentation cleanup patches
- tools/testing/selftests/cgroup/test_cpuset.c added
* tag 'cgroup-for-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (32 commits)
cgroup: Avoid -Wstringop-overflow warnings
cgroup:namespace: Remove unused cgroup_namespaces_init()
cgroup/rstat: Record the cumulative per-cpu time of cgroup and its descendants
cgroup: clean up if condition in cgroup_pidlist_start()
cgroup: fix obsolete function name in cgroup_destroy_locked()
Documentation: cgroup-v2.rst: Correct number of stats entries
cgroup: fix obsolete function name above css_free_rwork_fn()
cgroup/cpuset: fix kernel-doc
cgroup: clean up printk()
cgroup: fix obsolete comment above cgroup_create()
docs: cgroup-v1: fix typo
docs: cgroup-v1: correct the term of Page Cache organization in inode
cgroup/misc: Store atomic64_t reads to u64
cgroup/misc: Change counters to be explicit 64bit types
cgroup/misc: update struct members descriptions
cgroup: remove cgrp->kn check in css_populate_dir()
cgroup: fix obsolete function name
cgroup: use cached local variable parent in for loop
cgroup: remove obsolete comment above struct cgroupstats
cgroup: put cgroup_tryget_css() inside CONFIG_CGROUP_SCHED
...
Pull media updates from Mauro Carvalho Chehab:
- new i2c drivers: ds90ub913, ds90ub953, ds90ub960, dw9719, ds90ub913
- new Intel IVSC MEI drivers
- some Mediatek platform drivers were moved to a common location
- Intel atomisp2 driver is now working with the main ov2680 driver. Due
to that, the atomisp2 ov2680 staging one was removed
- the bttv driver was finally converted to videobuf2 framework. This
was the last one upstream using videobuf version 1 core. We'll likely
remove the old videobuf framework on 6.7
- lots of improvements at atomisp driver: it now works with normal I2C
sensors. Several compile-mode dependecies to select between ISP2400
and ISP2401 are now solved in runtime
- a new ipu-bridge logic was added to work with IVSC MEI drivers
- venus driver gained better support for new VPU versions
- the v4l core async framework has gained lots of improvements and
cleanups
- lots of other cleanups, improvements and driver fixes
* tag 'media/v6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (358 commits)
media: ivsc: Add ACPI dependency
media: bttv: convert to vb2
media: bttv: use audio defaults for winfast2000
media: bttv: refactor bttv_set_dma()
media: bttv: move vbi_skip/vbi_count out of buffer
media: bttv: remove crop info from bttv_buffer
media: bttv: remove tvnorm field from bttv_buffer
media: bttv: remove format field from bttv_buffer
media: bttv: move do_crop flag out of bttv_fh
media: bttv: copy vbi_fmt from bttv_fh
media: bttv: copy vid fmt/width/height from fh
media: bttv: radio use v4l2_fh instead of bttv_fh
media: bttv: replace BUG with WARN_ON
media: bttv: use video_drvdata to get bttv
media: i2c: rdacm21: Fix uninitialized value
media: coda: Remove duplicated include
media: vivid: fix the racy dev->radio_tx_rds_owner
media: i2c: ccs: Check rules is non-NULL
media: i2c: ds90ub960: Fix PLL config for 1200 MHz CSI rate
media: i2c: ds90ub953: Fix use of uninitialized variables
...
Pull char/misc driver updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
changes for 6.6-rc1.
Stuff all over the place here, lots of driver updates and changes and
new additions. Short summary is:
- new IIO drivers and updates
- Interconnect driver updates
- fpga driver updates and additions
- fsi driver updates
- mei driver updates
- coresight driver updates
- nvmem driver updates
- counter driver updates
- lots of smaller misc and char driver updates and additions
All of these have been in linux-next for a long time with no reported
problems"
* tag 'char-misc-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (267 commits)
nvmem: core: Notify when a new layout is registered
nvmem: core: Do not open-code existing functions
nvmem: core: Return NULL when no nvmem layout is found
nvmem: core: Create all cells before adding the nvmem device
nvmem: u-boot-env:: Replace zero-length array with DECLARE_FLEX_ARRAY() helper
nvmem: sec-qfprom: Add Qualcomm secure QFPROM support
dt-bindings: nvmem: sec-qfprom: Add bindings for secure qfprom
dt-bindings: nvmem: Add compatible for QCM2290
nvmem: Kconfig: Fix typo "drive" -> "driver"
nvmem: Explicitly include correct DT includes
nvmem: add new NXP QorIQ eFuse driver
dt-bindings: nvmem: Add t1023-sfp efuse support
dt-bindings: nvmem: qfprom: Add compatible for MSM8226
nvmem: uniphier: Use devm_platform_get_and_ioremap_resource()
nvmem: qfprom: do some cleanup
nvmem: stm32-romem: Use devm_platform_get_and_ioremap_resource()
nvmem: rockchip-efuse: Use devm_platform_get_and_ioremap_resource()
nvmem: meson-mx-efuse: Convert to devm_platform_ioremap_resource()
nvmem: lpc18xx_otp: Convert to devm_platform_ioremap_resource()
nvmem: brcm_nvram: Use devm_platform_get_and_ioremap_resource()
...
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported
issues. The last bit of cleanups from Jiri and the tty structure size
reduction came in last week, a bit late but as they were just style
changes and size reductions, I figured they should get into this merge
cycle so that others can work on top of them with no merge conflicts"
* tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits)
tty: shrink the size of struct tty_struct by 40 bytes
tty: n_tty: deduplicate copy code in n_tty_receive_buf_real_raw()
tty: n_tty: extract ECHO_OP processing to a separate function
tty: n_tty: unify counts to size_t
tty: n_tty: use u8 for chars and flags
tty: n_tty: simplify chars_in_buffer()
tty: n_tty: remove unsigned char casts from character constants
tty: n_tty: move newline handling to a separate function
tty: n_tty: move canon handling to a separate function
tty: n_tty: use MASK() for masking out size bits
tty: n_tty: make n_tty_data::num_overrun unsigned
tty: n_tty: use time_is_before_jiffies() in n_tty_receive_overrun()
tty: n_tty: use 'num' for writes' counts
tty: n_tty: use output character directly
tty: n_tty: make flow of n_tty_receive_buf_common() a bool
Revert "tty: serial: meson: Add a earlycon for the T7 SoC"
Documentation: devices.txt: Fix minors for ttyCPM*
Documentation: devices.txt: Remove ttySIOC*
Documentation: devices.txt: Remove ttyIOC*
serial: 8250_bcm7271: improve bcm7271 8250 port
...
Pull USB / Thunderbolt / PHY driver updates from Greg KH:
"Here is the big set of USB, Thunderbolt, and PHY driver updates for
6.6-rc1. Included in here are:
- PHY driver additions and cleanups
- Thunderbolt minor additions and fixes
- USB MIDI 2 gadget support added
- dwc3 driver updates and additions
- Removal of some old USB wireless code that was missed when that
codebase was originally removed a few years ago, cleaning up some
core USB code paths
- USB core potential use-after-free fixes that syzbot from different
people/groups keeps tripping over
- typec updates and additions
- gadget fixes and cleanups
- loads of smaller USB core and driver cleanups all over the place
Full details are in the shortlog. All of these have been in linux-next
for a while with no reported problems"
* tag 'usb-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (154 commits)
platform/chrome: cros_ec_typec: Configure Retimer cable type
tcpm: Avoid soft reset when partner does not support get_status
usb: typec: tcpm: reset counter when enter into unattached state after try role
usb: typec: tcpm: set initial svdm version based on pd revision
USB: serial: option: add FOXCONN T99W368/T99W373 product
USB: serial: option: add Quectel EM05G variant (0x030e)
usb: dwc2: add pci_device_id driver_data parse support
usb: gadget: remove max support speed info in bind operation
usb: gadget: composite: cleanup function config_ep_by_speed_and_alt()
usb: gadget: config: remove max speed check in usb_assign_descriptors()
usb: gadget: unconditionally allocate hs/ss descriptor in bind operation
usb: gadget: f_uvc: change endpoint allocation in uvc_function_bind()
usb: gadget: add a inline function gether_bitrate()
usb: gadget: use working speed to calcaulate network bitrate and qlen
dt-bindings: usb: samsung,exynos-dwc3: Add Exynos850 support
usb: dwc3: exynos: Add support for Exynos850 variant
usb: gadget: udc-xilinx: fix incorrect type in assignment warning
usb: gadget: udc-xilinx: fix cast from restricted __le16 warning
usb: gadget: udc-xilinx: fix restricted __le16 degrades to integer warning
USB: dwc2: hande irq on dead controller correctly
...
Pull RISC-V updates from Palmer Dabbelt:
- Support for the new "riscv,isa-extensions" and "riscv,isa-base"
device tree interfaces for probing extensions
- Support for userspace access to the performance counters
- Support for more instructions in kprobes
- Crash kernels can be allocated above 4GiB
- Support for KCFI
- Support for ELFs in !MMU configurations
- ARCH_KMALLOC_MINALIGN has been reduced to 8
- mmap() defaults to sv48-sized addresses, with longer addresses hidden
behind a hint (similar to Arm and Intel)
- Also various fixes and cleanups
* tag 'riscv-for-linus-6.6-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (51 commits)
lib/Kconfig.debug: Restrict DEBUG_INFO_SPLIT for RISC-V
riscv: support PREEMPT_DYNAMIC with static keys
riscv: Move create_tmp_mapping() to init sections
riscv: Mark KASAN tmp* page tables variables as static
riscv: mm: use bitmap_zero() API
riscv: enable DEBUG_FORCE_FUNCTION_ALIGN_64B
riscv: remove redundant mv instructions
RISC-V: mm: Document mmap changes
RISC-V: mm: Update pgtable comment documentation
RISC-V: mm: Add tests for RISC-V mm
RISC-V: mm: Restrict address space for sv39,sv48,sv57
riscv: enable DMA_BOUNCE_UNALIGNED_KMALLOC for !dma_coherent
riscv: allow kmalloc() caches aligned to the smallest value
riscv: support the elf-fdpic binfmt loader
binfmt_elf_fdpic: support 64-bit systems
riscv: Allow CONFIG_CFI_CLANG to be selected
riscv/purgatory: Disable CFI
riscv: Add CFI error handling
riscv: Add ftrace_stub_graph
riscv: Add types to indirectly called assembly functions
...
Pull powerpc updates from Michael Ellerman:
- Add HOTPLUG_SMT support (/sys/devices/system/cpu/smt) and honour the
configured SMT state when hotplugging CPUs into the system
- Combine final TLB flush and lazy TLB mm shootdown IPIs when using the
Radix MMU to avoid a broadcast TLBIE flush on exit
- Drop the exclusion between ptrace/perf watchpoints, and drop the now
unused associated arch hooks
- Add support for the "nohlt" command line option to disable CPU idle
- Add support for -fpatchable-function-entry for ftrace, with GCC >=
13.1
- Rework memory block size determination, and support 256MB size on
systems with GPUs that have hotpluggable memory
- Various other small features and fixes
Thanks to Andrew Donnellan, Aneesh Kumar K.V, Arnd Bergmann, Athira
Rajeev, Benjamin Gray, Christophe Leroy, Frederic Barrat, Gautam
Menghani, Geoff Levand, Hari Bathini, Immad Mir, Jialin Zhang, Joel
Stanley, Jordan Niethe, Justin Stitt, Kajol Jain, Kees Cook, Krzysztof
Kozlowski, Laurent Dufour, Liang He, Linus Walleij, Mahesh Salgaonkar,
Masahiro Yamada, Michal Suchanek, Nageswara R Sastry, Nathan Chancellor,
Nathan Lynch, Naveen N Rao, Nicholas Piggin, Nick Desaulniers, Omar
Sandoval, Randy Dunlap, Reza Arbab, Rob Herring, Russell Currey, Sourabh
Jain, Thomas Gleixner, Trevor Woerner, Uwe Kleine-König, Vaibhav Jain,
Xiongfeng Wang, Yuan Tan, Zhang Rui, and Zheng Zengkai.
* tag 'powerpc-6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (135 commits)
macintosh/ams: linux/platform_device.h is needed
powerpc/xmon: Reapply "Relax frame size for clang"
powerpc/mm/book3s64: Use 256M as the upper limit with coherent device memory attached
powerpc/mm/book3s64: Fix build error with SPARSEMEM disabled
powerpc/iommu: Fix notifiers being shared by PCI and VIO buses
powerpc/mpc5xxx: Add missing fwnode_handle_put()
powerpc/config: Disable SLAB_DEBUG_ON in skiroot
powerpc/pseries: Remove unused hcall tracing instruction
powerpc/pseries: Fix hcall tracepoints with JUMP_LABEL=n
powerpc: dts: add missing space before {
powerpc/eeh: Use pci_dev_id() to simplify the code
powerpc/64s: Move CPU -mtune options into Kconfig
powerpc/powermac: Fix unused function warning
powerpc/pseries: Rework lppaca_shared_proc() to avoid DEBUG_PREEMPT
powerpc: Don't include lppaca.h in paca.h
powerpc/pseries: Move hcall_vphn() prototype into vphn.h
powerpc/pseries: Move VPHN constants into vphn.h
cxl: Drop unused detach_spa()
powerpc: Drop zalloc_maybe_bootmem()
powerpc/powernv: Use struct opal_prd_msg in more places
...
