[ Upstream commit 680ad315ca ]
If gio_device_register fails, gio_dev_put() is required to
drop the gio_dev device reference.
Fixes: e84de0c619 ("MIPS: GIO bus support for SGI IP22/28")
Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9f048fa487 upstream.
Depending on the particular CPU implementation a TLB shutdown may occur
if multiple matching entries are detected upon the execution of a TLBP
or the TLBWI/TLBWR instructions. Given that we don't know what entries
we have been handed we need to be very careful with the initial TLB
setup and avoid all these instructions.
Therefore read all the TLB entries one by one with the TLBR instruction,
bypassing the content addressing logic, and truncate any large pages in
place so as to avoid a case in the second step where an incoming entry
for a large page at a lower address overlaps with a replacement entry
chosen at another index. Then preinitialize the TLB using addresses
outside our usual unique range and avoiding clashes with any entries
received, before making the usual call to local_flush_tlb_all().
This fixes (at least) R4x00 cores if TLBP hits multiple matching TLB
entries (SGI IP22 PROM for examples sets up all TLBs to the same virtual
address).
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 35ad7e1815 ("MIPS: mm: tlb-r4k: Uniquify TLB entries on init")
Cc: stable@vger.kernel.org
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com> # Boston I6400, M5150 sim
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebd729fef3 upstream.
Fix a regression that has caused accesses to the PCI MMIO window to
complete unclaimed in non-EVA configurations with the SOC-it family of
system controllers, preventing PCI devices from working that use MMIO.
In the non-EVA case PHYS_OFFSET is set to 0, meaning that PCI_BAR0 is
set with an empty mask (and PCI_HEAD4 matches addresses starting from 0
accordingly). Consequently all addresses are matched for incoming DMA
accesses from PCI. This seems to confuse the system controller's logic
and outgoing bus cycles targeting the PCI MMIO window seem not to make
it to the intended devices.
This happens as well when a wider mask is used with PCI_BAR0, such as
0x80000000 or 0xe0000000, that makes addresses match that overlap with
the PCI MMIO window, which starts at 0x10000000 in our configuration.
Set the mask in PCI_BAR0 to 0xf0000000 for non-EVA then, covering the
non-EVA maximum 256 MiB of RAM, which is what YAMON does and which used
to work correctly up to the offending commit. Set PCI_P2SCMSKL to match
PCI_BAR0 as required by the system controller's specification, and match
PCI_P2SCMAPL to PCI_HEAD4 for identity mapping.
Verified with:
Core board type/revision = 0x0d (Core74K) / 0x01
System controller/revision = MIPS SOC-it 101 OCP / 1.3 SDR-FW-4:1
Processor Company ID/options = 0x01 (MIPS Technologies, Inc.) / 0x1c
Processor ID/revision = 0x97 (MIPS 74Kf) / 0x4c
for non-EVA and with:
Core board type/revision = 0x0c (CoreFPGA-5) / 0x00
System controller/revision = MIPS ROC-it2 / 0.0 FW-1:1 (CLK_unknown) GIC
Processor Company ID/options = 0x01 (MIPS Technologies, Inc.) / 0x00
Processor ID/revision = 0xa0 (MIPS interAptiv UP) / 0x20
for EVA/non-EVA, fixing:
defxx 0000:00:12.0: assign IRQ: got 10
defxx: v1.12 2021/03/10 Lawrence V. Stefani and others
0000:00:12.0: Could not read adapter factory MAC address!
vs:
defxx 0000:00:12.0: assign IRQ: got 10
defxx: v1.12 2021/03/10 Lawrence V. Stefani and others
0000:00:12.0: DEFPA at MMIO addr = 0x10142000, IRQ = 10, Hardware addr = 00-00-f8-xx-xx-xx
0000:00:12.0: registered as fddi0
for non-EVA and causing no change for EVA.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 422dd25664 ("MIPS: Malta: Allow PCI devices DMA to lower 2GB physical")
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b0d04fe6a6 ]
Bindig requires a node name matching ‘^gpio@[0-9a-f]+$’. This patch
changes the clock name from “stp” to “gpio”.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35561bab76 ]
The include/generated/asm-offsets.h is generated in Kbuild during
compiling from arch/SRCARCH/kernel/asm-offsets.c. When we want to
generate another similar offset header file, circular dependency can
happen.
For example, we want to generate a offset file include/generated/test.h,
which is included in include/sched/sched.h. If we generate asm-offsets.h
first, it will fail, as include/sched/sched.h is included in asm-offsets.c
and include/generated/test.h doesn't exist; If we generate test.h first,
it can't success neither, as include/generated/asm-offsets.h is included
by it.
In x86_64, the macro COMPILE_OFFSETS is used to avoid such circular
dependency. We can generate asm-offsets.h first, and if the
COMPILE_OFFSETS is defined, we don't include the "generated/test.h".
And we define the macro COMPILE_OFFSETS for all the asm-offsets.c for this
purpose.
Signed-off-by: Menglong Dong <dongml2@chinatelecom.cn>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bf5570590a upstream.
MIPS Malta platform code registers the PCI southbridge legacy port I/O
PS/2 keyboard range as a standard resource marked as busy. It prevents
the i8042 driver from registering as it fails to claim the resource in
a call to i8042_platform_init(). Consequently PS/2 keyboard and mouse
devices cannot be used with this platform.
Fix the issue by removing the busy marker from the standard reservation,
making the driver register successfully:
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
and the resource show up as expected among the legacy devices:
00000000-00ffffff : MSC PCI I/O
00000000-0000001f : dma1
00000020-00000021 : pic1
00000040-0000005f : timer
00000060-0000006f : keyboard
00000060-0000006f : i8042
00000070-00000077 : rtc0
00000080-0000008f : dma page reg
000000a0-000000a1 : pic2
000000c0-000000df : dma2
[...]
If the i8042 driver has not been configured, then the standard resource
will remain there preventing any conflicting dynamic assignment of this
PCI port I/O address range.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/alpine.DEB.2.21.2510211919240.8377@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8c431ea8f3 ]
Bindig requires a node name matching ‘^ethernet@[0-9a-f]+$’. This patch
changes the clock name from “etop” to “ethernet”.
This fixes the following warning:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): $nodename:0: 'etop@e180000' does not match '^ethernet@[0-9a-f]+$'
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
Fixes: dac0bad937 ("dt-bindings: net: lantiq,etop-xway: Document Lantiq Xway ETOP bindings")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b28232921 ]
The upstream dts lacks the lantiq,{rx/tx}-burst-length property. Other
issues were also fixed:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): 'interrupt-names' is a required property
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): 'lantiq,tx-burst-length' is a required property
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): 'lantiq,rx-burst-length' is a required property
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
Fixes: 14d4e308e0 ("net: lantiq: configure the burst length in ethernet drivers")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 22375adaa0 upstream.
The MIPS32r2 ChaCha code has never been buildable with the clang
assembler. First, clang doesn't support the 'rotl' pseudo-instruction:
error: unknown instruction, did you mean: rol, rotr?
Second, clang requires that both operands of the 'wsbh' instruction be
explicitly given:
error: too few operands for instruction
To fix this, align the code with the real instruction set by (1) using
the real instruction 'rotr' instead of the nonstandard pseudo-
instruction 'rotl', and (2) explicitly giving both operands to 'wsbh'.
To make removing the use of 'rotl' a bit easier, also remove the
unnecessary special-casing for big endian CPUs at
.Lchacha_mips_xor_bytes. The tail handling is actually
endian-independent since it processes one byte at a time. On big endian
CPUs the old code byte-swapped SAVED_X, then iterated through it in
reverse order. But the byteswap and reverse iteration canceled out.
Tested with chacha20poly1305-selftest in QEMU using "-M malta" with both
little endian and big endian mips32r2 kernels.
Fixes: 49aa7c00ed ("crypto: mips/chacha - import 32r2 ChaCha code from Zinc")
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202505080409.EujEBwA0-lkp@intel.com/
Link: https://lore.kernel.org/r/20250619225535.679301-1-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9c9a7ff988 ]
request_mem_region() will return NULL instead of error code
when the memory request fails. Therefore, we should check if
the return value is non-zero instead of less than zero. In
this way, this patch also fixes the build warnings:
arch/mips/lantiq/falcon/sysctrl.c:214:50: error: ordered comparison of pointer with integer zero [-Werror=extra]
214 | res_status.name) < 0) ||
| ^
arch/mips/lantiq/falcon/sysctrl.c:216:47: error: ordered comparison of pointer with integer zero [-Werror=extra]
216 | res_ebu.name) < 0) ||
| ^
arch/mips/lantiq/falcon/sysctrl.c:219:50: error: ordered comparison of pointer with integer zero [-Werror=extra]
219 | res_sys[0].name) < 0) ||
| ^
arch/mips/lantiq/falcon/sysctrl.c:222:50: error: ordered comparison of pointer with integer zero [-Werror=extra]
222 | res_sys[1].name) < 0) ||
| ^
arch/mips/lantiq/falcon/sysctrl.c:225:50: error: ordered comparison of pointer with integer zero [-Werror=extra]
225 | res_sys[2].name) < 0))
|
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9f4a6b342 ]
Not all tasks have an ABI associated or vDSO mapped,
for example kthreads never do.
If such a task ever ends up calling stack_top(), it will derefence the
NULL ABI pointer and crash.
This can for example happen when using kunit:
mips_stack_top+0x28/0xc0
arch_pick_mmap_layout+0x190/0x220
kunit_vm_mmap_init+0xf8/0x138
__kunit_add_resource+0x40/0xa8
kunit_vm_mmap+0x88/0xd8
usercopy_test_init+0xb8/0x240
kunit_try_run_case+0x5c/0x1a8
kunit_generic_run_threadfn_adapter+0x28/0x50
kthread+0x118/0x240
ret_from_kernel_thread+0x14/0x1c
Only dereference the ABI point if it is set.
The GIC page is also included as it is specific to the vDSO.
Also move the randomization adjustment into the same conditional.
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Reviewed-by: David Gow <davidgow@google.com>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 844615dd0f ]
These functions are exported but their prototypes are not defined.
This patch adds the missing function prototypes to fix the following
compilation warnings:
arch/mips/kernel/vpe-mt.c:180:7: error: no previous prototype for 'vpe_alloc' [-Werror=missing-prototypes]
180 | void *vpe_alloc(void)
| ^~~~~~~~~
arch/mips/kernel/vpe-mt.c:198:5: error: no previous prototype for 'vpe_start' [-Werror=missing-prototypes]
198 | int vpe_start(void *vpe, unsigned long start)
| ^~~~~~~~~
arch/mips/kernel/vpe-mt.c:208:5: error: no previous prototype for 'vpe_stop' [-Werror=missing-prototypes]
208 | int vpe_stop(void *vpe)
| ^~~~~~~~
arch/mips/kernel/vpe-mt.c:229:5: error: no previous prototype for 'vpe_free' [-Werror=missing-prototypes]
229 | int vpe_free(void *vpe)
| ^~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 35ad7e1815 upstream.
Hardware or bootloader will initialize TLB entries to any value, which
may collide with kernel's UNIQUE_ENTRYHI value. On MIPS microAptiv/M5150
family of cores this will trigger machine check exception and cause boot
failure. On M5150 simulation this could happen 7 times out of 1000 boots.
Replace local_flush_tlb_all() with r4k_tlb_uniquify() which probes each
TLB ENTRIHI unique value for collisions before it's written, and in case
of collision try a different ASID.
Cc: stable@kernel.org
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f4ae7c6ec upstream.
GCC 15 changed the default C standard dialect from gnu17 to gnu23,
which should not have impacted the kernel because it explicitly requests
the gnu11 standard in the main Makefile. However, mips/vdso code uses
its own CFLAGS without a '-std=' value, which break with this dialect
change because of the kernel's own definitions of bool, false, and true
conflicting with the C23 reserved keywords.
include/linux/stddef.h:11:9: error: cannot use keyword 'false' as enumeration constant
11 | false = 0,
| ^~~~~
include/linux/stddef.h:11:9: note: 'false' is a keyword with '-std=c23' onwards
include/linux/types.h:35:33: error: 'bool' cannot be defined via 'typedef'
35 | typedef _Bool bool;
| ^~~~
include/linux/types.h:35:33: note: 'bool' is a keyword with '-std=c23' onwards
Add -std as specified in KBUILD_CFLAGS to the decompressor and purgatory
CFLAGS to eliminate these errors and make the C standard version of these
areas match the rest of the kernel.
Signed-off-by: Khem Raj <raj.khem@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 00a134fc2b ]
The pm-cps code has up until now used per-CPU variables indexed by core,
rather than CPU number, in order to share data amongst sibling CPUs (ie.
VPs/threads in a core). This works fine for single cluster systems, but
with multi-cluster systems a core number is no longer unique in the
system, leading to sharing between CPUs that are not actually siblings.
Avoid this issue by using per-CPU variables as they are more generally
used - ie. access them using CPU numbers rather than core numbers.
Sharing between siblings is then accomplished by:
- Assigning the same pointer to entries for each sibling CPU for the
nc_asm_enter & ready_count variables, which allow this by virtue of
being per-CPU pointers.
- Indexing by the first CPU set in a CPUs cpu_sibling_map in the case
of pm_barrier, for which we can't use the previous approach because
the per-CPU variable is not a pointer.
Signed-off-by: Paul Burton <paulburton@kernel.org>
Signed-off-by: Dragan Mladjenovic <dragan.mladjenovic@syrmia.com>
Signed-off-by: Aleksandar Rikalo <arikalo@gmail.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 756276ce78 ]
On MIPS system, most of the syscall function name begin with prefix
sys_. Some syscalls are special such as clone/fork, function name of
these begin with __sys_. Since scratch registers need be saved in
stack when these system calls happens.
With ftrace system call method, system call functions are declared with
SYSCALL_DEFINEx, metadata of the system call symbol name begins with
sys_. Here mips specific function arch_syscall_match_sym_name is used to
compare function name between sys_call_table[] and metadata of syscall
symbol.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c44572e0cc ]
Fix MAX_REG_OFFSET to point to the last register in 'pt_regs' and not to
the marker itself, which could allow regs_get_register() to return an
invalid offset.
Fixes: 40e084a506 ("MIPS: Add uprobes support.")
Suggested-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b73c3ccdca upstream.
Commit e27fbe16af ("MIPS: cm: Detect CM quirks from device tree")
introduced
arch/mips/include/asm/mips-cm.h:119:13: error: ‘mips_cm_update_property’
defined but not used [-Werror=unused-function]
Fix this by making empty function implementation inline
Fixes: e27fbe16af ("MIPS: cm: Detect CM quirks from device tree")
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e27fbe16af ]
Some information that should be retrieved at runtime for the Coherence
Manager can be either absent or wrong. This patch allows checking if
some of this information is available from the device tree and updates
the internal variable accordingly.
For now, only the compatible string associated with the broken HCI is
being retrieved.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a759109b23 upstream.
Synchronize the declaration of ds1287_set_base_clock() between
cevt-ds1287.c and ds1287.h.
Fix follow error with gcc-14 when -Werror:
arch/mips/kernel/cevt-ds1287.c:21:5: error: conflicting types for ‘ds1287_set_base_clock’; have ‘int(unsigned int)’
21 | int ds1287_set_base_clock(unsigned int hz)
| ^~~~~~~~~~~~~~~~~~~~~
In file included from arch/mips/kernel/cevt-ds1287.c:13:
./arch/mips/include/asm/ds1287.h:11:13: note: previous declaration of ‘ds1287_set_base_clock’ with type ‘void(unsigned int)’
11 | extern void ds1287_set_base_clock(unsigned int clock);
| ^~~~~~~~~~~~~~~~~~~~~
make[7]: *** [scripts/Makefile.build:207: arch/mips/kernel/cevt-ds1287.o] Error 1
make[6]: *** [scripts/Makefile.build:465: arch/mips/kernel] Error 2
make[6]: *** Waiting for unfinished jobs....
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3be225f33 upstream.
Address the issue of cevt-ds1287.c not including the ds1287.h header
file.
Fix follow errors with gcc-14 when -Werror:
arch/mips/kernel/cevt-ds1287.c:15:5: error: no previous prototype for ‘ds1287_timer_state’ [-Werror=missing-prototypes]
15 | int ds1287_timer_state(void)
| ^~~~~~~~~~~~~~~~~~
arch/mips/kernel/cevt-ds1287.c:20:5: error: no previous prototype for ‘ds1287_set_base_clock’ [-Werror=missing-prototypes]
20 | int ds1287_set_base_clock(unsigned int hz)
| ^~~~~~~~~~~~~~~~~~~~~
arch/mips/kernel/cevt-ds1287.c:103:12: error: no previous prototype for ‘ds1287_clockevent_init’ [-Werror=missing-prototypes]
103 | int __init ds1287_clockevent_init(int irq)
| ^~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
make[7]: *** [scripts/Makefile.build:207: arch/mips/kernel/cevt-ds1287.o] Error 1
make[7]: *** Waiting for unfinished jobs....
make[6]: *** [scripts/Makefile.build:465: arch/mips/kernel] Error 2
make[6]: *** Waiting for unfinished jobs....
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55fa586851 upstream.
Declare which_prom() as static to suppress gcc compiler warning that
'missing-prototypes'. This function is not intended to be called
from other parts.
Fix follow error with gcc-14 when -Werror:
arch/mips/dec/prom/init.c:45:13: error: no previous prototype for ‘which_prom’ [-Werror=missing-prototypes]
45 | void __init which_prom(s32 magic, s32 *prom_vec)
| ^~~~~~~~~~
cc1: all warnings being treated as errors
make[6]: *** [scripts/Makefile.build:207: arch/mips/dec/prom/init.o] Error 1
make[5]: *** [scripts/Makefile.build:465: arch/mips/dec/prom] Error 2
make[5]: *** Waiting for unfinished jobs....
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 02410ac72a upstream.
In order to fix a bug, arm64 needs to be told the size of the huge page
for which the huge_pte is being cleared in huge_ptep_get_and_clear().
Provide for this by adding an `unsigned long sz` parameter to the
function. This follows the same pattern as huge_pte_clear() and
set_huge_pte_at().
This commit makes the required interface modifications to the core mm as
well as all arches that implement this function (arm64, loongarch, mips,
parisc, powerpc, riscv, s390, sparc). The actual arm64 bug will be fixed
in a separate commit.
Cc: stable@vger.kernel.org
Fixes: 66b3923a1a ("arm64: hugetlb: add support for PTE contiguous bit")
Acked-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com> # riscv
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com> # s390
Link: https://lore.kernel.org/r/20250226120656.2400136-2-ryan.roberts@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ddd068d814 upstream.
Declare ftrace_get_parent_ra_addr() as static to suppress clang
compiler warning that 'no previous prototype'. This function is
not intended to be called from other parts.
Fix follow error with clang-19:
arch/mips/kernel/ftrace.c:251:15: error: no previous prototype for function 'ftrace_get_parent_ra_addr' [-Werror,-Wmissing-prototypes]
251 | unsigned long ftrace_get_parent_ra_addr(unsigned long self_ra, unsigned long
| ^
arch/mips/kernel/ftrace.c:251:1: note: declare 'static' if the function is not intended to be used outside of this translation unit
251 | unsigned long ftrace_get_parent_ra_addr(unsigned long self_ra, unsigned long
| ^
| static
1 error generated.
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42a39e4aa5 upstream.
Currently, installation of Debian 12.8 for mipsel fails on machines
without an FPU [1]. This is caused by the fact that zstd (which is used
for initramfs compression) executes the prefx instruction, which is not
emulated properly by the kernel.
The prefx (Prefetch Indexed) instruction fetches data from memory into
the cache without any side effects. Though functionally unrelated, it
requires an FPU [2].
Bytecode format of this instruction ends on "001111" binary:
(prefx instruction format) & 0x0000003f = 0x0000000f
The code in fpux_emu() runs like so:
#define MIPSInst(x) x
#define MIPSInst_FMA_FFMT(x) (MIPSInst(x) & 0x00000007)
#define MIPSInst_FUNC(x) (MIPSInst(x) & 0x0000003f)
enum cop1x_func { ..., pfetch_op = 0x0f, ... };
...
switch (MIPSInst_FMA_FFMT(ir)) {
...
case 0x3:
if (MIPSInst_FUNC(ir) != pfetch_op)
return SIGILL;
/* ignore prefx operation */
break;
default:
return SIGILL;
}
That snippet above contains a logic error and the
if (MIPSInst_FUNC(ir) != pfetch_op)
comparison always fires.
When MIPSInst_FUNC(ir) is equal to pfetch_op, ir must end on 001111
binary. In this case, MIPSInst_FMA_FFMT(ir) must be equal to 0x7, which
does not match that case label.
This causes emulation failure for the prefx instruction. Fix it.
This has been broken by
commit 919af8b96c ("MIPS: Make definitions of MIPSInst_FMA_{FUNC,FMTM} consistent with MIPS64 manual")
which modified the MIPSInst_FMA_FFMT macro without updating the users.
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Cc: stable@vger.kernel.org # after 3 weeks
Cc: Dengcheng Zhu <dzhu@wavecomp.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Ming Wang <wangming01@loongson.cn>
Cc: Tiezhu Yang <yangtiezhu@loongson.cn>
Fixes: 919af8b96c ("MIPS: Make definitions of MIPSInst_FMA_{FUNC,FMTM} consistent with MIPS64 manual")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[1] https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=1091858
[2] MIPS Architecture For Programmers Volume II-A: The MIPS32 Instruction Set
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
commit bd2212d658 upstream.
Per Appendix A.7 in Q/LS 0013-2014 (龙芯CPU开发系统固件与内核接口规范 V2.2,
lit. Loongson DevSys Firmware Kernel Interface Specification V2.2),
interface_info.size is size of this interface, not size of the LEFI BIOS
ROM.
In any case, the BIOS ROM Size just cannot be several kilobytes (KB) on
Loongson64 LEFI platforms.
Reported-by: Mingcong Bai <jeffbai@aosc.io>
Suggested-by: Icenowy Zheng <uwu@icenowy.me>
Fixes: 6c1bfbd9df ("MIPS: Loongson64: Add /sys/firmware/lefi/boardinfo")
Cc: stable@vger.kernel.org
Signed-off-by: Kexy Biscuit <kexybiscuit@aosc.io>
Acked-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a640d6762a ]
c994a3ec7e ("MIPS: set mips32r5 for virt extensions") setted
some instructions in virt extensions to ISA level mips32r5.
However TLB related vz instructions was leftover, also this
shouldn't be done to a R5 or R6 kernel buid.
Reorg macros to set ISA level as needed when _ASM_SET_VIRT
is called.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4fbd66d825 ]
Fix the dtc warnings:
arch/mips/boot/dts/loongson/ls7a-pch.dtsi:68.16-416.5: Warning (interrupt_provider): /bus@10000000/pci@1a000000: '#interrupt-cells' found, but node is not an interrupt provider
arch/mips/boot/dts/loongson/ls7a-pch.dtsi:68.16-416.5: Warning (interrupt_provider): /bus@10000000/pci@1a000000: '#interrupt-cells' found, but node is not an interrupt provider
arch/mips/boot/dts/loongson/loongson64g_4core_ls7a.dtb: Warning (interrupt_map): Failed prerequisite 'interrupt_provider'
And a runtime warning introduced in commit 045b14ca5c ("of: WARN on
deprecated #address-cells/#size-cells handling"):
WARNING: CPU: 0 PID: 1 at drivers/of/base.c:106 of_bus_n_addr_cells+0x9c/0xe0
Missing '#address-cells' in /bus@10000000/pci@1a000000/pci_bridge@9,0
The fix is similar to commit d89a415ff8 ("MIPS: Loongson64: DTS: Fix PCIe
port nodes for ls7a"), which has fixed the issue for ls2k (despite its
subject mentions ls7a).
Signed-off-by: Xi Ruoyao <xry111@xry111.site>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2473a3597 ]
__pa() is only intended to be used for linear map addresses and using
it for initial_boot_params which is in fixmap for arm64 will give an
incorrect value. Hence save the physical address when it is known at
boot time when calling early_init_dt_scan for arm64 and use it at kexec
time instead of converting the virtual address using __pa().
Note that arm64 doesn't need the FDT region reserved in the DT as the
kernel explicitly reserves the passed in FDT. Therefore, only a debug
warning is fixed with this change.
Reported-by: Breno Leitao <leitao@debian.org>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Usama Arif <usamaarif642@gmail.com>
Fixes: ac10be5cdb ("arm64: Use common of_kexec_alloc_and_setup_fdt()")
Link: https://lore.kernel.org/r/20241023171426.452688-1-usamaarif642@gmail.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da09935975 ]
When MIPS_FP_SUPPORT is disabled, __sanitize_fcr31() is defined as
nothing, which triggers a gcc warning:
In file included from kernel/sched/core.c:79:
kernel/sched/core.c: In function 'context_switch':
./arch/mips/include/asm/switch_to.h:114:39: warning: suggest braces around empty body in an 'if' statement [-Wempty-body]
114 | __sanitize_fcr31(next); \
| ^
kernel/sched/core.c:5316:9: note: in expansion of macro 'switch_to'
5316 | switch_to(prev, next, prev);
| ^~~~~~~~~
Fix this by providing an empty body for __sanitize_fcr31() like one is
defined for __mips_mt_fpaff_switch_to().
Fixes: 36a498035b ("MIPS: Avoid FCSR sanitization when CONFIG_MIPS_FP_SUPPORT=n")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1cb6ab4464 upstream.
Loongson64 C and G processors have EXTIMER feature which
is conflicting with CP0 counter.
Although the processor resets in EXTIMER disabled & INTIMER
enabled mode, which is compatible with MIPS CP0 compare, firmware
may attempt to enable EXTIMER and interfere CP0 compare.
Set timer mode back to MIPS compatible mode to fix booting on
systems with such firmware before we have an actual driver for
EXTIMER.
Cc: stable@vger.kernel.org
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a263e5f309 ]
When the CM block migrated from CM2.5 to CM3.0, the address offset for
the Global CSR Access Privilege register was modified. We saw this in
the "MIPS64 I6500 Multiprocessing System Programmer's Guide," it is
stated that "the Global CSR Access Privilege register is located at
offset 0x0120" in section 5.4. It is at least the same for I6400.
This fix allows to use the VP cores in SMP mode if the reset values
were modified by the bootloader.
Based on the work of Vladimir Kondratiev
<vladimir.kondratiev@mobileye.com> and the feedback from Jiaxun Yang
<jiaxun.yang@flygoat.com>.
Fixes: 197e89e098 ("MIPS: mips-cm: Implement mips_cm_revision")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4e7ca0b57f upstream.
We should always use firmware's poweroff & reboot service
if it's available as firmware may need to perform more task
than platform's syscon etc.
However _machine_restart & poweroff hooks are registered at
low priority, which means platform reboot driver can override
them.
Register firmware based reboot/poweroff implementation with
register_sys_off_handler with appropriate priority so that
they will be prioritised. Remove _machine_halt hook as it's
deemed to be unnecessary.
Cc: stable@vger.kernel.org
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
