[ Upstream commit 00aaae60fa ]
There are GPIO controllers such as the one present in the LX2160ARDB
QIXIS FPGA which have fixed-direction input and output GPIO lines mixed
together in a single register. This cannot be modeled using the
gpio-regmap as-is since there is no way to present the true direction of
a GPIO line.
In order to make this use case possible, add a new configuration
parameter - fixed_direction_output - into the gpio_regmap_config
structure. This will enable user drivers to provide a bitmap that
represents the fixed direction of the GPIO lines.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Stable-dep-of: 2ba5772e53 ("gpio: idio-16: Define fixed direction of the GPIO lines")
Signed-off-by: William Breathitt Gray <wbg@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4c4e6ea4a1 ]
The generic_handle_domain_irq() function resolves the hardware IRQ
internally. The driver performed a duplicative mapping by calling
irq_find_mapping() first, which could lead to an RCU stall.
Delete the redundant irq_find_mapping() call and pass the hardware IRQ
directly to generic_handle_domain_irq().
Fixes: c5a4b6fd31 ("gpio: Add support for Intel LJCA USB GPIO driver")
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Link: https://lore.kernel.org/r/20251023070231.1305-1-vulab@iscas.ac.cn
[Bartosz: remove unused variable]
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b5f8aa8d4b ]
The slimbus regmap passed to the GPIO driver down from MFD does not use
fast_io. This means a mutex is used for locking and thus this GPIO chip
must not be used in atomic context. Change the can_sleep switch in
struct gpio_chip to true.
Fixes: 59c3246834 ("gpio: wcd934x: Add support to wcd934x gpio controller")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6ccc4dde1 ]
When a software-node gets added to a device which already has another
fwnode as primary node it will become the secondary fwnode for that
device.
Currently if a software-node with GPIO properties ends up as the secondary
fwnode then gpiod_find_by_fwnode() will fail to find the GPIOs.
Add a new gpiod_fwnode_lookup() helper which falls back to calling
gpiod_find_by_fwnode() with the secondary fwnode if the GPIO was not
found in the primary fwnode.
Fixes: e7f9ff5dc9 ("gpiolib: add support for software nodes")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hansg@kernel.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20250920200955.20403-1-hansg@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
[ Adjust context ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 10af0273a3 ]
The gpio-mlxbf3 driver interfaces with two GPIO controllers,
device instance 0 and 1. There is a single IRQ resource shared
between the two controllers, and it is found in the ACPI table for
device instance 0. The driver should not attempt to get an IRQ
resource when probing device instance 1, otherwise the following
error is logged:
mlxbf3_gpio MLNXBF33:01: error -ENXIO: IRQ index 0 not found
Signed-off-by: David Thompson <davthompson@nvidia.com>
Reviewed-by: Shravan Kumar Ramani <shravankr@nvidia.com>
Fixes: cd33f216d2 ("gpio: mlxbf3: Add gpio driver support")
Link: https://lore.kernel.org/r/20250613163443.1065217-1-davthompson@nvidia.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e38f94606 ]
If an input changes state during wake-up and is used as an interrupt
source, the IRQ handler reads the volatile input register to clear the
interrupt mask and deassert the IRQ line. However, the IRQ handler is
triggered before access to the register is granted, causing the read
operation to fail.
As a result, the IRQ handler enters a loop, repeatedly printing the
"failed reading register" message, until `pca953x_resume()` is eventually
called, which restores the driver context and enables access to
registers.
Fix by disabling the IRQ line before entering suspend mode, and
re-enabling it after the driver context is restored in `pca953x_resume()`.
An IRQ can be disabled with disable_irq() and still wake the system as
long as the IRQ has wake enabled, so the wake-up functionality is
preserved.
Fixes: b765743005 ("gpio: pca953x: Restore registers after suspend/resume cycle")
Cc: stable@vger.kernel.org
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20250512095441.31645-1-francesco@dolcini.it
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 12f65d1203 upstream.
Both new_device_store and delete_device_store touch module global
resources (e.g. gpio_aggregator_lock). To prevent race conditions with
module unload, a reference needs to be held.
Add try_module_get() in these handlers.
For new_device_store, this eliminates what appears to be the most dangerous
scenario: if an id is allocated from gpio_aggregator_idr but
platform_device_register has not yet been called or completed, a concurrent
module unload could fail to unregister/delete the device, leaving behind a
dangling platform device/GPIO forwarder. This can result in various issues.
The following simple reproducer demonstrates these problems:
#!/bin/bash
while :; do
# note: whether 'gpiochip0 0' exists or not does not matter.
echo 'gpiochip0 0' > /sys/bus/platform/drivers/gpio-aggregator/new_device
done &
while :; do
modprobe gpio-aggregator
modprobe -r gpio-aggregator
done &
wait
Starting with the following warning, several kinds of warnings will appear
and the system may become unstable:
------------[ cut here ]------------
list_del corruption, ffff888103e2e980->next is LIST_POISON1 (dead000000000100)
WARNING: CPU: 1 PID: 1327 at lib/list_debug.c:56 __list_del_entry_valid_or_report+0xa3/0x120
[...]
RIP: 0010:__list_del_entry_valid_or_report+0xa3/0x120
[...]
Call Trace:
<TASK>
? __list_del_entry_valid_or_report+0xa3/0x120
? __warn.cold+0x93/0xf2
? __list_del_entry_valid_or_report+0xa3/0x120
? report_bug+0xe6/0x170
? __irq_work_queue_local+0x39/0xe0
? handle_bug+0x58/0x90
? exc_invalid_op+0x13/0x60
? asm_exc_invalid_op+0x16/0x20
? __list_del_entry_valid_or_report+0xa3/0x120
gpiod_remove_lookup_table+0x22/0x60
new_device_store+0x315/0x350 [gpio_aggregator]
kernfs_fop_write_iter+0x137/0x1f0
vfs_write+0x262/0x430
ksys_write+0x60/0xd0
do_syscall_64+0x6c/0x180
entry_SYSCALL_64_after_hwframe+0x76/0x7e
[...]
</TASK>
---[ end trace 0000000000000000 ]---
Fixes: 828546e242 ("gpio: Add GPIO Aggregator")
Cc: stable@vger.kernel.org
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Link: https://lore.kernel.org/r/20250224143134.3024598-2-koichiro.den@canonical.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b9644fbfbc upstream.
The stmpe_reg_read function can fail, but its return value is not checked
in stmpe_gpio_irq_sync_unlock. This can lead to silent failures and
incorrect behavior if the hardware access fails.
This patch adds checks for the return value of stmpe_reg_read. If the
function fails, an error message is logged and the function returns
early to avoid further issues.
Fixes: b888fb6f2a ("gpio: stmpe: i2c transfer are forbiden in atomic context")
Cc: stable@vger.kernel.org # 4.16+
Signed-off-by: Wentao Liang <vulab@iscas.ac.cn>
Link: https://lore.kernel.org/r/20250212021849.275-1-vulab@iscas.ac.cn
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 57f5db77a9 ]
The settings for all GPIOs are locked by default in bcm_kona_gpio_reset.
The settings for a GPIO are unlocked when requesting it as a GPIO, but
not when requesting it as an interrupt, causing the IRQ settings to not
get applied.
Fix this by making sure to unlock the right bits when an IRQ is requested.
To avoid a situation where an IRQ being released causes a lock despite
the same GPIO being used by a GPIO request or vice versa, add an unlock
counter and only lock if it reaches 0.
Fixes: 757651e3d6 ("gpio: bcm281xx: Add GPIO driver")
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Markus Mayer <mmayer@broadcom.com>
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20250206-kona-gpio-fixes-v2-2-409135eab780@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6179f6c62 ]
The GPIO drivers with latch interrupt support (typically types starting
with PCAL) have interrupt status registers to determine which particular
inputs have caused an interrupt. Unfortunately there is no atomic
operation to read these registers and clear the interrupt. Clearing the
interrupt is done by reading the input registers.
The code was reading the interrupt status registers, and then reading
the input registers. If an input changed between these two events it was
lost.
The solution in this patch is to revert to the non-latch version of
code, i.e. remembering the previous input status, and looking for the
changes. This system results in no more I2C transfers, so is no slower.
The latch property of the device still means interrupts will still be
noticed if the input changes back to its initial state.
Fixes: 44896beae6 ("gpio: pca953x: add PCAL9535 interrupt support for Galileo Gen2")
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240606033102.2271916-1-mark.tomlinson@alliedtelesis.co.nz
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53c59d66c4 ]
Curtrently the error path is unsynchronised with removal due to
regulator being disabled before other device managed resources
are handled. Correct that by wrapping regulator enablement in
the respective call.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Stable-dep-of: 7cef813a91 ("gpio: pca953x: log an error when failing to get the reset GPIO")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9722c3b66e ]
The of_property_for_each_u32() macro needs five parameters, two of which
are primarily meant as internal variables for the macro itself (in the
for() clause). Yet these two parameters are used by a few drivers, and this
can be considered misuse or at least bad practice.
Now that the kernel uses C11 to build, these two parameters can be avoided
by declaring them internally, thus changing this pattern:
struct property *prop;
const __be32 *p;
u32 val;
of_property_for_each_u32(np, "xyz", prop, p, val) { ... }
to this:
u32 val;
of_property_for_each_u32(np, "xyz", val) { ... }
However two variables cannot be declared in the for clause even with C11,
so declare one struct that contain the two variables we actually need. As
the variables inside this struct are not meant to be used by users of this
macro, give the struct instance the noticeable name "_it" so it is visible
during code reviews, helping to avoid new code to use it directly.
Most usages are trivially converted as they do not use those two
parameters, as expected. The non-trivial cases are:
- drivers/clk/clk.c, of_clk_get_parent_name(): easily doable anyway
- drivers/clk/clk-si5351.c, si5351_dt_parse(): this is more complex as the
checks had to be replicated in a different way, making code more verbose
and somewhat uglier, but I refrained from a full rework to keep as much
of the original code untouched having no hardware to test my changes
All the changes have been build tested. The few for which I have the
hardware have been runtime-tested too.
Reviewed-by: Andre Przywara <andre.przywara@arm.com> # drivers/clk/sunxi/clk-simple-gates.c, drivers/clk/sunxi/clk-sun8i-bus-gates.c
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> # drivers/gpio/gpio-brcmstb.c
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> # drivers/irqchip/irq-atmel-aic-common.c
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # drivers/iio/adc/ti_am335x_adc.c
Acked-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com> # drivers/pwm/pwm-samsung.c
Acked-by: Richard Leitner <richard.leitner@linux.dev> # drivers/usb/misc/usb251xb.c
Acked-by: Mark Brown <broonie@kernel.org> # sound/soc/codecs/arizona.c
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com> # sound/soc/codecs/arizona.c
Acked-by: Michael Ellerman <mpe@ellerman.id.au> # arch/powerpc/sysdev/xive/spapr.c
Acked-by: Stephen Boyd <sboyd@kernel.org> # clk
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Acked-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20240724-of_property_for_each_u32-v3-1-bea82ce429e2@bootlin.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Stable-dep-of: 28fa3291ca ("clk: fix an OF node reference leak in of_clk_get_parent_name()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 72cef64180 upstream.
Setting GPIO direction = high, sometimes results in GPIO value = 0.
If a GPIO is pulled high, the following construction results in the
value being 0 when the desired value is 1:
$ echo "high" > /sys/class/gpio/gpio336/direction
$ cat /sys/class/gpio/gpio336/value
0
Before the GPIO direction is changed from an input to an output,
exar_set_value() is called with value = 1, but since the GPIO is an
input when exar_set_value() is called, _regmap_update_bits() reads a 1
due to an external pull-up. regmap_set_bits() sets force_write =
false, so the value (1) is not written. When the direction is then
changed, the GPIO becomes an output with the value of 0 (the hardware
default).
regmap_write_bits() sets force_write = true, so the value is always
written by exar_set_value() and an external pull-up doesn't affect the
outcome of setting direction = high.
The same can happen when a GPIO is pulled low, but the scenario is a
little more complicated.
$ echo high > /sys/class/gpio/gpio351/direction
$ cat /sys/class/gpio/gpio351/value
1
$ echo in > /sys/class/gpio/gpio351/direction
$ cat /sys/class/gpio/gpio351/value
0
$ echo low > /sys/class/gpio/gpio351/direction
$ cat /sys/class/gpio/gpio351/value
1
Fixes: 36fb7218e8 ("gpio: exar: switch to using regmap")
Co-developed-by: Matthew McClain <mmcclain@noprivs.com>
Signed-off-by: Matthew McClain <mmcclain@noprivs.com>
Signed-off-by: Sai Kumar Cholleti <skmr537@gmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20241105071523.2372032-1-skmr537@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1bb5a99e1f ]
Performing a dummy read ensures that the register write operation is fully
completed, mitigating any potential bus delays that could otherwise impact
the frequency of bitbang usage. E.g., if the JTAG application uses GPIO to
control the JTAG pins (TCK, TMS, TDI, TDO, and TRST), and the application
sets the TCK clock to 1 MHz, the GPIO's high/low transitions will rely on
a delay function to ensure the clock frequency does not exceed 1 MHz.
However, this can lead to rapid toggling of the GPIO because the write
operation is POSTed and does not wait for a bus acknowledgment.
Fixes: 361b79119a ("gpio: Add Aspeed driver")
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20241008081450.1490955-2-billy_tsai@aspeedtech.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b440396387 upstream.
linereq_set_config() behaves badly when direction is not set.
The configuration validation is borrowed from linereq_create(), where,
to verify the intent of the user, the direction must be set to in order to
effect a change to the electrical configuration of a line. But, when
applied to reconfiguration, that validation does not allow for the unset
direction case, making it possible to clear flags set previously without
specifying the line direction.
Adding to the inconsistency, those changes are not immediately applied by
linereq_set_config(), but will take effect when the line value is next get
or set.
For example, by requesting a configuration with no flags set, an output
line with GPIO_V2_LINE_FLAG_ACTIVE_LOW and GPIO_V2_LINE_FLAG_OPEN_DRAIN
set could have those flags cleared, inverting the sense of the line and
changing the line drive to push-pull on the next line value set.
Skip the reconfiguration of lines for which the direction is not set, and
only reconfigure the lines for which direction is set.
Fixes: a54756cb24 ("gpiolib: cdev: support GPIO_V2_LINE_SET_CONFIG_IOCTL")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20240626052925.174272-3-warthog618@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
