[ Upstream commit 95d9c3f0e4 ]
Commit under Fixes introduced support for PCIe EP mode on AM654x platforms.
When the mode happens to be either "DW_PCIE_RC_TYPE" or "DW_PCIE_EP_TYPE",
the PCIe Controller is configured accordingly. However, when the mode is
neither of them, an error message is displayed, but the driver probe
succeeds. Since this "invalid" mode is not associated with a functional
PCIe Controller, the probe should fail.
Fix the behavior by exiting "ks_pcie_probe()" with the return value of
"-EINVAL" in addition to displaying the existing error message when the
mode is invalid.
Fixes: 23284ad677 ("PCI: keystone: Add support for PCIe EP in AM654x Platforms")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20251029080547.1253757-4-s-vadapalli@ti.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09fefb24ed ]
dw_pcie_edma_irq_verify() is supposed to verify the eDMA IRQs in devicetree
by fetching them using either 'dma' or 'dmaX' IRQ names. Former is used
when the platform uses a single IRQ for all eDMA channels and latter is
used when the platform uses separate IRQ per channel. But currently,
dw_pcie_edma_irq_verify() bails out early if edma::nr_irqs is 1, i.e., when
a single IRQ is used. This gives an impression that the driver could work
with any single IRQ in devicetree, not necessarily with name 'dma'.
But dw_pcie_edma_irq_vector(), which actually requests the IRQ, does
require the single IRQ to be named as 'dma'. So this creates inconsistency
between dw_pcie_edma_irq_verify() and dw_pcie_edma_irq_vector().
Thus, to fix this inconsistency, make sure dw_pcie_edma_irq_verify() also
verifies the single IRQ name by removing the bail out code.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
[mani: reworded subject and description]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: fix typos]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250908165914.547002-3-cassel@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42f9c66a6d ]
Tegra already defines all BARs except BAR0 as BAR_RESERVED. This is
sufficient for pci-epf-test to not allocate backing memory and to not call
set_bar() for those BARs. However, marking a BAR as BAR_RESERVED does not
mean that the BAR gets disabled.
The host side driver, pci_endpoint_test, simply does an ioremap for all
enabled BARs and will run tests against all enabled BARs, so it will run
tests against the BARs marked as BAR_RESERVED.
After running the BAR tests (which will write to all enabled BARs), the
inbound address translation is broken. This is because the tegra controller
exposes the ATU Port Logic Structure in BAR4, so when BAR4 is written, the
inbound address translation settings get overwritten.
To avoid this, implement the dw_pcie_ep_ops .init() callback and start off
by disabling all BARs (pci-epf-test will later enable/configure BARs that
are not defined as BAR_RESERVED).
This matches the behavior of other PCIe endpoint drivers: dra7xx, imx6,
layerscape-ep, artpec6, dw-rockchip, qcom-ep, rcar-gen4, and uniphier-ep.
With this, the PCI endpoint kselftest test case CONSECUTIVE_BAR_TEST (which
was specifically made to detect address translation issues) passes.
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250922140822.519796-7-cassel@kernel.org
[ changed .init field to .ep_init in pcie_ep_ops struct ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f842d3313b ]
The Cadence PCIe Controller integrated in the TI K3 SoCs supports both
Root-Complex and Endpoint modes of operation. The Glue Layer allows
"strapping" the Mode of operation of the Controller, the Link Speed
and the Link Width. This is enabled by programming the "PCIEn_CTRL"
register (n corresponds to the PCIe instance) within the CTRL_MMR
memory-mapped register space. The "reset-values" of the registers are
also different depending on the mode of operation.
Since the PCIe Controller latches onto the "reset-values" immediately
after being powered on, if the Glue Layer configuration is not done while
the PCIe Controller is off, it will result in the PCIe Controller latching
onto the wrong "reset-values". In practice, this will show up as a wrong
representation of the PCIe Controller's capability structures in the PCIe
Configuration Space. Some such capabilities which are supported by the PCIe
Controller in the Root-Complex mode but are incorrectly latched onto as
being unsupported are:
- Link Bandwidth Notification
- Alternate Routing ID (ARI) Forwarding Support
- Next capability offset within Advanced Error Reporting (AER) capability
Fix this by powering off the PCIe Controller before programming the "strap"
settings and powering it on after that. The runtime PM APIs namely
pm_runtime_put_sync() and pm_runtime_get_sync() will decrement and
increment the usage counter respectively, causing GENPD to power off and
power on the PCIe Controller.
Fixes: f3e25911a4 ("PCI: j721e: Add TI J721E PCIe driver")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250908120828.1471776-1-s-vadapalli@ti.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 82c4be4168 ]
The ACSPCIE module is capable of driving the reference clock required by
the PCIe Endpoint device. It is an alternative to on-board and external
reference clock generators. Enabling the output from the ACSPCIE module's
PAD IO Buffers requires clearing the "PAD IO disable" bits of the
ACSPCIE_PROXY_CTRL register in the CTRL_MMR register space.
Add support to enable the ACSPCIE reference clock output using the optional
device-tree property "ti,syscon-acspcie-proxy-ctrl".
Link: https://lore.kernel.org/linux-pci/20240829105316.1483684-3-s-vadapalli@ti.com
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Stable-dep-of: f842d3313b ("PCI: j721e: Fix programming sequence of "strap" settings")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f8c9ad46b0 upstream.
The return value from tegra_bpmp_transfer() indicates the success or
failure of the IPC transaction with BPMP. If the transaction succeeded, we
also need to check the actual command's result code.
If we don't have error handling for tegra_bpmp_transfer(), we will set the
pcie->ep_state to EP_STATE_ENABLED even when the tegra_bpmp_transfer()
command fails. Thus, the pcie->ep_state will get out of sync with reality,
and any further PERST# assert + deassert will be a no-op and will not
trigger the hardware initialization sequence.
This is because pex_ep_event_pex_rst_deassert() checks the current
pcie->ep_state, and does nothing if the current state is already
EP_STATE_ENABLED.
Thus, it is important to have error handling for tegra_bpmp_transfer(),
such that the pcie->ep_state can not get out of sync with reality, so that
we will try to initialize the hardware not only during the first PERST#
assert + deassert, but also during any succeeding PERST# assert + deassert.
One example where this fix is needed is when using a rock5b as host.
During the initial PERST# assert + deassert (triggered by the bootloader on
the rock5b) pex_ep_event_pex_rst_deassert() will get called, but for some
unknown reason, the tegra_bpmp_transfer() call to initialize the PHY fails.
Once Linux has been loaded on the rock5b, the PCIe driver will once again
assert + deassert PERST#. However, without tegra_bpmp_transfer() error
handling, this second PERST# assert + deassert will not trigger the
hardware initialization sequence.
With tegra_bpmp_transfer() error handling, the second PERST# assert +
deassert will once again trigger the hardware to be initialized and this
time the tegra_bpmp_transfer() succeeds.
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
[cassel: improve commit log]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250922140822.519796-8-cassel@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b640d42a6a upstream.
The pci_epc_raise_irq() supplies a MSI or MSI-X interrupt number in range
(1-N), as per the pci_epc_raise_irq() kdoc, where N is 32 for MSI.
But tegra_pcie_ep_raise_msi_irq() incorrectly uses the interrupt number as
the MSI vector. This causes wrong MSI vector to be triggered, leading to
the failure of PCI endpoint Kselftest MSI_TEST test case.
To fix this issue, convert the interrupt number to MSI vector.
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250922140822.519796-6-cassel@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a8f173d9d upstream.
The pmsr_lock spinlock used to be necessary to synchronize access to the
PMSR register, because that access could have been triggered from either
config space access in rcar_pcie_config_access() or an exception handler
rcar_pcie_aarch32_abort_handler().
The rcar_pcie_aarch32_abort_handler() case is no longer applicable since
commit 6e36203bc1 ("PCI: rcar: Use PCI_SET_ERROR_RESPONSE after read
which triggered an exception"), which performs more accurate, controlled
invocation of the exception, and a fixup.
This leaves rcar_pcie_config_access() as the only call site from which
rcar_pcie_wakeup() is called. The rcar_pcie_config_access() can only be
called from the controller struct pci_ops .read and .write callbacks,
and those are serialized in drivers/pci/access.c using raw spinlock
'pci_lock' . It should be noted that CONFIG_PCI_LOCKLESS_CONFIG is never
set on this platform.
Since the 'pci_lock' is a raw spinlock , and the 'pmsr_lock' is not a
raw spinlock, this constellation triggers 'BUG: Invalid wait context'
with CONFIG_PROVE_RAW_LOCK_NESTING=y .
Remove the pmsr_lock to fix the locking.
Fixes: a115b1bd3a ("PCI: rcar: Add L1 link state fix into data abort hook")
Reported-by: Duy Nguyen <duy.nguyen.rh@renesas.com>
Reported-by: Thuan Nguyen <thuan.nguyen-hong@banvien.com.vn>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250909162707.13927-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4f152338e3 ]
During PERST# assertion tegra_pcie_bpmp_set_pll_state() is currently
called twice.
pex_ep_event_pex_rst_assert() should do the opposite of
pex_ep_event_pex_rst_deassert(), so it is obvious that the duplicate
tegra_pcie_bpmp_set_pll_state() is a mistake, and that the duplicate
tegra_pcie_bpmp_set_pll_state() call should instead be a call to
tegra_pcie_bpmp_set_ctrl_state().
With this, the uninitialization sequence also matches that of
tegra_pcie_unconfig_controller().
Fixes: a54e190737 ("PCI: tegra194: Add Tegra234 PCIe support")
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
[cassel: improve commit log]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Link: https://patch.msgid.link/20250911093021.1454385-2-cassel@kernel.org
[mani: added Fixes tag]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1a8805e5d ]
Fix incorrect argument order in devm_kcalloc() when allocating port->phys.
The original call used sizeof(phy) as the number of elements and
port->lanes as the element size, which is reversed. While this happens to
produce the correct total allocation size with current pointer size and
lane counts, the argument order is wrong.
Fixes: 6fe7c187e0 ("PCI: tegra: Support per-lane PHYs")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
[mani: added Fixes tag]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250819150436.3105973-1-alok.a.tiwari@oracle.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e6ea70690 ]
According to Documentation/PCI/endpoint/pci-endpoint-cfs.rst, the Endpoint
controller (EPC) should only start the link when userspace writes '1' to
the '/sys/kernel/config/pci_ep/controllers/<EPC>/start' attribute, which
ultimately results in calling imx_pcie_start_link() via
pci_epc_start_store().
To align with the documented behavior, do not start the link automatically
when adding the EP controller.
Fixes: 75c2f26da0 ("PCI: imx6: Add i.MX PCIe EP mode support")
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[mani: reworded commit subject and description]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250709033722.2924372-3-hongxing.zhu@nxp.com
[ imx_pcie_ltssm_enable() => imx6_pcie_ltssm_enable() ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit af3c6eacce ]
As per DWC PCIe registers description 4.30a, section 1.13.43, NUM_OF_LANES
named as PORT_LOGIC_LINK_WIDTH in PCIe DWC driver, is referred to as the
"Predetermined Number of Lanes" in PCIe r6.0, sec 4.2.7.2.1, which explains
the conditions required to enter Polling.Configuration:
Next state is Polling.Configuration after at least 1024 TS1 Ordered Sets
were transmitted, and all Lanes that detected a Receiver during Detect
receive eight consecutive training sequences ...
Otherwise, after a 24 ms timeout the next state is:
Polling.Configuration if,
(i) Any Lane, which detected a Receiver during Detect, received eight
consecutive training sequences ... and a minimum of 1024 TS1 Ordered
Sets are transmitted after receiving one TS1 or TS2 Ordered Set.
And
(ii) At least a predetermined set of Lanes that detected a Receiver
during Detect have detected an exit from Electrical Idle at least
once since entering Polling.Active.
Note: This may prevent one or more bad Receivers or Transmitters
from holding up a valid Link from being configured, and allow for
additional training in Polling.Configuration. The exact set of
predetermined Lanes is implementation specific.
Note: Any Lane that receives eight consecutive TS1 or TS2 Ordered
Sets should have detected an exit from Electrical Idle at least
once since entering Polling.Active.
In a PCIe link supporting multiple lanes, if PORT_LOGIC_LINK_WIDTH is set
to lane width the hardware supports, all lanes that detect a receiver
during the Detect phase must receive eight consecutive training sequences.
Otherwise, LTSSM will not enter Polling.Configuration and link training
will fail.
Therefore, always set PORT_LOGIC_LINK_WIDTH to 1, regardless of the number
of lanes the port actually supports, to make link up more robust. This
setting will not affect the intended link width if all lanes are
functional. Additionally, the link can still be established with at least
one lane if other lanes are faulty.
Co-developed-by: Qiang Yu <quic_qianyu@quicinc.com>
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Signed-off-by: Wenbin Yao <quic_wenbyao@quicinc.com>
[mani: subject change]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[bhelgaas: update PCIe spec citation, format quote]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Niklas Cassel <cassel@kernel.org>
Link: https://patch.msgid.link/20250422103623.462277-1-quic_wenbyao@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c8bcb01352 upstream.
While cdns_pcie_ep_set_msix() writes the Table Size field correctly (N-1),
the calculation of the PBA offset is wrong because it calculates space for
(N-1) entries instead of N.
This results in the following QEMU error when using PCI passthrough on a
device which relies on the PCI endpoint subsystem:
failed to add PCI capability 0x11[0x50]@0xb0: table & pba overlap, or they don't fit in BARs, or don't align
Fix the calculation of PBA offset in the MSI-X capability.
[bhelgaas: more specific subject and commit log]
Fixes: 3ef5d16f50 ("PCI: cadence: Add MSI-X support to Endpoint driver")
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250514074313.283156-10-cassel@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8805f32a96 ]
If the call to pci_host_probe() in cdns_pcie_host_setup() fails, PM
runtime count is decremented in the error path using pm_runtime_put_sync().
But the runtime count is not incremented by this driver, but only by the
callers (cdns_plat_pcie_probe/j721e_pcie_probe). And the callers also
decrement the runtime PM count in their error path. So this leads to the
below warning from the PM core:
"runtime PM usage count underflow!"
So fix it by getting rid of pm_runtime_put_sync() in the error path and
directly return the errno.
Fixes: 49e427e6bd ("Merge branch 'pci/host-probe-refactor'")
Signed-off-by: Hans Zhang <18255117159@163.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250419133058.162048-1-18255117159@163.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c4d5aadf5 ]
MSI remapping bypass (directly configuring MSI entries for devices on the
VMD bus) won't work under Xen, as Xen is not aware of devices in such bus,
and hence cannot configure the entries using the pIRQ interface in the PV
case, and in the PVH case traps won't be setup for MSI entries for such
devices.
Until Xen is aware of devices in the VMD bus prevent the
VMD_FEAT_CAN_BYPASS_MSI_REMAP capability from being used when running as
any kind of Xen guest.
The MSI remapping bypass is an optional feature of VMD bridges, and hence
when running under Xen it will be masked and devices will be forced to
redirect its interrupts from the VMD bridge. That mode of operation must
always be supported by VMD bridges and works when Xen is not aware of
devices behind the VMD bridge.
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Message-ID: <20250219092059.90850-3-roger.pau@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3e1dccba0 ]
Most systems' PCIe outbound map windows have non-zero physical addresses,
but the possibility of encountering zero increased after following commit
("PCI: dwc: Use parent_bus_offset").
'ep->outbound_addr[n]', representing 'parent_bus_address', might be 0 on
some hardware, which trims high address bits through bus fabric before
sending to the PCIe controller.
Replace the iteration logic with 'for_each_set_bit()' to ensure only
allocated map windows are iterated when determining the ATU index from a
given address.
Link: https://lore.kernel.org/r/20250315201548.858189-12-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit 2a12efc567 which is
commit f068ffdd03 upstream.
This is a backport mistake.
Deleting "IMX7D" here skips more than just controller_id logic. It skips
reset assignments too, which causes:
imx6q-pcie 33800000.pcie: PCIe PLL lock timeout
In my case, in addition to broken PCIe, kernel boot hangs entirely.
This isn't a problem upstream because before this, they moved the rest of
the code out of the switch case.
Signed-off-by: Ryan Matthews <ryanmatthews@fastmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 18056a4866 ]
The access to the PCI config space via pci_ops::read and pci_ops::write is
a low-level hardware access. The functions can be accessed with disabled
interrupts even on PREEMPT_RT. The pci_lock is a raw_spinlock_t for this
purpose.
A spinlock_t becomes a sleeping lock on PREEMPT_RT, so it cannot be
acquired with disabled interrupts. The vmd_dev::cfg_lock is accessed in
the same context as the pci_lock.
Make vmd_dev::cfg_lock a raw_spinlock_t type so it can be used with
interrupts disabled.
This was reported as:
BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48
Call Trace:
rt_spin_lock+0x4e/0x130
vmd_pci_read+0x8d/0x100 [vmd]
pci_user_read_config_byte+0x6f/0xe0
pci_read_config+0xfe/0x290
sysfs_kf_bin_read+0x68/0x90
Signed-off-by: Ryo Takakura <ryotkkr98@gmail.com>
Tested-by: Luis Claudio R. Goncalves <lgoncalv@redhat.com>
Acked-by: Luis Claudio R. Goncalves <lgoncalv@redhat.com>
[bigeasy: reword commit message]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-off-by: Luis Claudio R. Goncalves <lgoncalv@redhat.com>
Link: https://lore.kernel.org/r/20250218080830.ufw3IgyX@linutronix.de
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: add back report info from
https://lore.kernel.org/lkml/20241218115951.83062-1-ryotkkr98@gmail.com/]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3651ad5249 ]
If the regulator_bulk_get() returns an error and no regulators
are created, we need to set their number to zero.
If we don't do this and the PCIe link up fails, a call to the
regulator_bulk_free() will result in a kernel panic.
While at it, print the error value, as we cannot return an error
upwards as the kernel will WARN() on an error from add_bus().
Fixes: 9e6be018b2 ("PCI: brcmstb: Enable child bus device regulators from DT")
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20250214173944.47506-5-james.quinlan@broadcom.com
[kwilczynski: commit log, use comma in the message to match style with
other similar messages]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ac47fbf4f ]
Per the Cadence's "PCIe Controller IP for AX14" user guide, Version
1.04, Section 9.1.7.1, "AXI Subordinate to PCIe Address Translation
Registers", Table 9.4, the bit 16 of the AXI Subordinate Address
(axi_s_awaddr) when set corresponds to MSG with data, and when not set,
to MSG without data.
However, the driver is currently doing the opposite and due to this,
the INTx is never received on the host.
So, fix the driver to reflect the documentation and also make INTx work.
Fixes: 37dddf14f1 ("PCI: cadence: Add EndPoint Controller driver for Cadence PCIe controller")
Signed-off-by: Hans Zhang <18255117159@163.com>
Signed-off-by: Hans Zhang <hans.zhang@cixtech.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214165724.184599-1-18255117159@163.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d2da5a4c1 ]
The rcar_pcie_parse_outbound_ranges() uses the devm_request_mem_region()
macro to request a needed resource. A string variable that lives on the
stack is then used to store a dynamically computed resource name, which
is then passed on as one of the macro arguments. This can lead to
undefined behavior.
Depending on the current contents of the memory, the manifestations of
errors may vary. One possible output may be as follows:
$ cat /proc/iomem
30000000-37ffffff :
38000000-3fffffff :
Sometimes, garbage may appear after the colon.
In very rare cases, if no NULL-terminator is found in memory, the system
might crash because the string iterator will overrun which can lead to
access of unmapped memory above the stack.
Thus, fix this by replacing outbound_name with the name of the previously
requested resource. With the changes applied, the output will be as
follows:
$ cat /proc/iomem
30000000-37ffffff : memory2
38000000-3fffffff : memory3
Fixes: 2a6d0d63d9 ("PCI: rcar: Add endpoint mode support")
Link: https://lore.kernel.org/r/tencent_DBDCC19D60F361119E76919ADAB25EC13C06@qq.com
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: King Dix <kingdix10@qq.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit 3e221877dd which is
commit 7246a4520b upstream.
This patch causes a regression in cuttlefish/crossvm boot on arm64.
The patch was part of a series that when applied will not cause a regression
but this patch was backported to the 6.6 branch by itself.
The other patches do not apply cleanly to the 6.6 branch.
Signed-off-by: Terry Tritton <terry.tritton@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7246a4520b ]
Use preserve_config in place of checking for PCI_PROBE_ONLY flag to enable
support for "linux,pci-probe-only" on a per host bridge basis.
This also obviates the use of adding PCI_REASSIGN_ALL_BUS flag if
!PCI_PROBE_ONLY, as pci_assign_unassigned_root_bus_resources() takes care
of reassigning the resources that are not already claimed.
Link: https://lore.kernel.org/r/20240508174138.3630283-5-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f24c9bfcd4 ]
The vmd driver creates a "domain" symlink in sysfs for each VMD bridge.
Previously this symlink was created after pci_bus_add_devices() added
devices below the VMD bridge and emitted udev events to announce them to
userspace.
This led to a race between userspace consumers of the udev events and the
kernel creation of the symlink. One such consumer is mdadm, which
assembles block devices into a RAID array, and for devices below a VMD
bridge, mdadm depends on the "domain" symlink.
If mdadm loses the race, it may be unable to assemble a RAID array, which
may cause a boot failure or other issues, with complaints like this:
(udev-worker)[2149]: nvme1n1: '/sbin/mdadm -I /dev/nvme1n1'(err) 'mdadm: Unable to get real path for '/sys/bus/pci/drivers/vmd/0000:c7:00.5/domain/device''
(udev-worker)[2149]: nvme1n1: '/sbin/mdadm -I /dev/nvme1n1'(err) 'mdadm: /dev/nvme1n1 is not attached to Intel(R) RAID controller.'
(udev-worker)[2149]: nvme1n1: '/sbin/mdadm -I /dev/nvme1n1'(err) 'mdadm: No OROM/EFI properties for /dev/nvme1n1'
(udev-worker)[2149]: nvme1n1: '/sbin/mdadm -I /dev/nvme1n1'(err) 'mdadm: no RAID superblock on /dev/nvme1n1.'
(udev-worker)[2149]: nvme1n1: Process '/sbin/mdadm -I /dev/nvme1n1' failed with exit code 1.
This symptom prevents the OS from booting successfully.
After a NVMe disk is probed/added by the nvme driver, udevd invokes mdadm
to detect if there is a mdraid associated with this NVMe disk, and mdadm
determines if a NVMe device is connected to a particular VMD domain by
checking the "domain" symlink. For example:
Thread A Thread B Thread mdadm
vmd_enable_domain
pci_bus_add_devices
__driver_probe_device
...
work_on_cpu
schedule_work_on
: wakeup Thread B
nvme_probe
: wakeup scan_work
to scan nvme disk
and add nvme disk
then wakeup udevd
: udevd executes
mdadm command
flush_work main
: wait for nvme_probe done ...
__driver_probe_device find_driver_devices
: probe next nvme device : 1) Detect domain symlink
... 2) Find domain symlink
... from vmd sysfs
... 3) Domain symlink not
... created yet; failed
sysfs_create_link
: create domain symlink
Create the VMD "domain" symlink before invoking pci_bus_add_devices() to
avoid this race.
Suggested-by: Adrian Huang <ahuang12@lenovo.com>
Link: https://lore.kernel.org/linux-pci/20240605124844.24293-1-sjiwei@163.com
Signed-off-by: Jiwei Sun <sunjw10@lenovo.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Nirmal Patel <nirmal.patel@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d660410631 ]
The remapped PCIe Root Port and the child device have PM L1 Substates
capability, but they are disabled originally.
Here is a failed example on ASUS B1400CEAE:
Capabilities: [900 v1] L1 PM Substates
L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1- ASPM_L1.2+ ASPM_L1.1- L1_PM_Substates+
PortCommonModeRestoreTime=32us PortTPowerOnTime=10us
L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2+ ASPM_L1.1-
T_CommonMode=0us LTR1.2_Threshold=101376ns
L1SubCtl2: T_PwrOn=50us
Enable PCI-PM L1 PM Substates for devices below VMD while they are in D0
(see PCIe r6.0, sec 5.5.4).
Link: https://lore.kernel.org/r/20241001083438.10070-4-jhp@endlessos.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218394
Signed-off-by: Jian-Hong Pan <jhp@endlessos.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
