[ Upstream commit 2c27aaee93 ]
Do read-modify-write so that we re-use the characterized reset value as
specified in TRM [1] to program calibration wait time which defines number
of cycles to wait for after startup state machine is in bandgap enable
state.
This fixes PLL lock timeout error faced while using RPi DSI Panel on TI's
AM62L and J721E SoC since earlier calibration wait time was getting
overwritten to zero value thus failing the PLL to lockup and causing
timeout.
[1] AM62P TRM (Section 14.8.6.3.2.1.1 DPHY_TX_DPHYTX_CMN0_CMN_DIG_TBIT2):
Link: https://www.ti.com/lit/pdf/spruj83
Cc: stable@vger.kernel.org
Fixes: 7a343c8bf4 ("phy: Add Cadence D-PHY support")
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Tested-by: Harikrishna Shenoy <h-shenoy@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://lore.kernel.org/r/20250704125915.1224738-3-devarsht@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 284fb19a3f ]
PLL lockup and O_CMN_READY assertion can only happen after common state
machine gets enabled by programming DPHY_CMN_SSM register, but driver was
polling them before the common state machine was enabled which is
incorrect. This is as per the DPHY initialization sequence as mentioned in
J721E TRM [1] at section "12.7.2.4.1.2.1 Start-up Sequence Timing Diagram".
It shows O_CMN_READY polling at the end after common configuration pin
setup where the common configuration pin setup step enables state machine
as referenced in "Table 12-1533. Common Configuration-Related Setup
mentions state machine"
To fix this :
- Add new function callbacks for polling on PLL lock and O_CMN_READY
assertion.
- As state machine and clocks get enabled in power_on callback only, move
the clock related programming part from configure callback to power_on
callback and poll for the PLL lockup and O_CMN_READY assertion after state
machine gets enabled.
- The configure callback only saves the PLL configuration received from the
client driver which will be applied later on in power_on callback.
- Add checks to ensure configure is called before power_on and state
machine is in disabled state before power_on callback is called.
- Disable state machine in power_off so that client driver can re-configure
the PLL by following up a power_off, configure, power_on sequence.
[1]: https://www.ti.com/lit/zip/spruil1
Cc: stable@vger.kernel.org
Fixes: 7a343c8bf4 ("phy: Add Cadence D-PHY support")
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Tested-by: Harikrishna Shenoy <h-shenoy@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://lore.kernel.org/r/20250704125915.1224738-2-devarsht@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7bb14b61b7 ]
The boot firmware may disable the U3 port early during boot and leave it
up to the controller or PHY driver to re-enable U3 when needed.
The Rockchip USBDP PHY driver currently does this for RK3576 and RK3588,
something the Rockchip Naneng Combo PHY driver never does for RK3568.
This may result in USB 3.0 ports being limited to only using USB 2.0 or
in special cases not working at all on RK3568.
Write to PIPE_GRF USB3OTGx_CON1 reg to ensure the U3 port is enabled
when a PHY with PHY_TYPE_USB3 mode is used.
Fixes: 7160820d74 ("phy: rockchip: add naneng combo phy for RK3568")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20250723072324.2246498-1-jonas@kwiboo.se
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 24c63c590a upstream.
The logic that drives the pad calibration values resides in the
controller reset domain and so the calibration values are only being
captured when the controller is out of reset. However, by clearing the
CYA_TRK_CODE_UPDATE_ON_IDLE bit, the calibration values can be set
while the controller is in reset.
The CYA_TRK_CODE_UPDATE_ON_IDLE bit was previously cleared based on the
trk_hw_mode flag, but this dependency is not necessary. Instead,
introduce a new flag, trk_update_on_idle, to independently control this
bit.
Fixes: d8163a32ca ("phy: tegra: xusb: Add Tegra234 support")
Cc: stable@vger.kernel.org
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20250519090929.3132456-2-waynec@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cefc1caee9 upstream.
When transitioning from USB_ROLE_DEVICE to USB_ROLE_NONE, the code
assumed that the regulator should be disabled. However, if the regulator
is marked as always-on, regulator_is_enabled() continues to return true,
leading to an incorrect attempt to disable a regulator which is not
enabled.
This can result in warnings such as:
[ 250.155624] WARNING: CPU: 1 PID: 7326 at drivers/regulator/core.c:3004
_regulator_disable+0xe4/0x1a0
[ 250.155652] unbalanced disables for VIN_SYS_5V0
To fix this, we move the regulator control logic into
tegra186_xusb_padctl_id_override() function since it's directly related
to the ID override state. The regulator is now only disabled when the role
transitions from USB_ROLE_HOST to USB_ROLE_NONE, by checking the VBUS_ID
register. This ensures that regulator enable/disable operations are
properly balanced and only occur when actually transitioning to/from host
mode.
Fixes: 49d46e3c7e ("phy: tegra: xusb: Add set_mode support for UTMI phy on Tegra186")
Cc: stable@vger.kernel.org
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20250502092606.2275682-1-waynec@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b15ee09ddb upstream.
The description of TX_VBOOST_LVL is wrong in register PHY_CTRL3
bit[31:29].
The updated description as below:
011: Corresponds to a launch amplitude of 0.844 V.
100: Corresponds to a launch amplitude of 1.008 V.
101: Corresponds to a launch amplitude of 1.156 V.
This will fix the parsing function
phy_tx_vboost_level_from_property() to return correct value.
Fixes: 63c85ad0cd ("phy: fsl-imx8mp-usb: add support for phy tuning")
Cc: stable@vger.kernel.org
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20250430094502.2723983-3-xu.yang_2@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d14402a38c ]
The qmp_usb_iomap() helper function currently returns the raw result of
devm_ioremap() for non-exclusive mappings. Since devm_ioremap() may return
a NULL pointer and the caller only checks error pointers with IS_ERR(),
NULL could bypass the check and lead to an invalid dereference.
Fix the issue by checking if devm_ioremap() returns NULL. When it does,
qmp_usb_iomap() now returns an error pointer via IOMEM_ERR_PTR(-ENOMEM),
ensuring safe and consistent error handling.
Signed-off-by: Chenyuan Yang <chenyuan0y@gmail.com>
Fixes: a5d6b1ac56 ("phy: qcom-qmp-usb: fix memleak on probe deferral")
CC: Johan Hovold <johan@kernel.org>
CC: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250414125050.2118619-1-chenyuan0y@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55a387ebb9 ]
The phy-rcar-gen3-usb2 driver exposes four individual PHYs that are
requested and configured by PHY users. The struct phy_ops APIs access the
same set of registers to configure all PHYs. Additionally, PHY settings can
be modified through sysfs or an IRQ handler. While some struct phy_ops APIs
are protected by a driver-wide mutex, others rely on individual
PHY-specific mutexes.
This approach can lead to various issues, including:
1/ the IRQ handler may interrupt PHY settings in progress, racing with
hardware configuration protected by a mutex lock
2/ due to msleep(20) in rcar_gen3_init_otg(), while a configuration thread
suspends to wait for the delay, another thread may try to configure
another PHY (with phy_init() + phy_power_on()); re-running the
phy_init() goes to the exact same configuration code, re-running the
same hardware configuration on the same set of registers (and bits)
which might impact the result of the msleep for the 1st configuring
thread
3/ sysfs can configure the hardware (though role_store()) and it can
still race with the phy_init()/phy_power_on() APIs calling into the
drivers struct phy_ops
To address these issues, add a spinlock to protect hardware register access
and driver private data structures (e.g., calls to
rcar_gen3_is_any_rphy_initialized()). Checking driver-specific data remains
necessary as all PHY instances share common settings. With this change,
the existing mutex protection is removed and the cleanup.h helpers are
used.
While at it, to keep the code simpler, do not skip
regulator_enable()/regulator_disable() APIs in
rcar_gen3_phy_usb2_power_on()/rcar_gen3_phy_usb2_power_off() as the
regulators enable/disable operations are reference counted anyway.
Fixes: f3b5a8d9b5 ("phy: rcar-gen3-usb2: Add R-Car Gen3 USB2 PHY driver")
Cc: stable@vger.kernel.org
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250507125032.565017-4-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stable-dep-of: 9ce71e85b2 ("phy: renesas: rcar-gen3-usb2: Assert PLL reset on PHY power off")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de76809f60 ]
Commit 08b0ad375c ("phy: renesas: rcar-gen3-usb2: move IRQ registration
to init") moved the IRQ request operation from probe to
struct phy_ops::phy_init API to avoid triggering interrupts (which lead to
register accesses) while the PHY clocks (enabled through runtime PM APIs)
are not active. If this happens, it results in a synchronous abort.
One way to reproduce this issue is by enabling CONFIG_DEBUG_SHIRQ, which
calls free_irq() on driver removal.
Move the IRQ request and free operations back to probe, and take the
runtime PM state into account in IRQ handler. This commit is preparatory
for the subsequent fixes in this series.
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250507125032.565017-3-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stable-dep-of: 9ce71e85b2 ("phy: renesas: rcar-gen3-usb2: Assert PLL reset on PHY power off")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4eae163753 ]
The Renesas RZ/G3S need to initialize the USB BUS before transferring data
due to hardware limitation. As the register that need to be touched for
this is in the address space of the USB PHY, and the UBS PHY need to be
initialized before any other USB drivers handling data transfer, add
support to initialize the USB BUS.
As the USB PHY is probed before any other USB drivers that enables
clocks and de-assert the reset signals and the BUS initialization is done
in the probe phase, we need to add code to de-assert reset signal and
runtime resume the device (which enables its clocks) before accessing
the registers.
As the reset signals are not required by the USB PHY driver for the other
USB PHY hardware variants, the reset signals and runtime PM was handled
only in the function that initialize the USB BUS.
The PHY initialization was done right after runtime PM enable to have
all in place when the PHYs are registered.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20240822152801.602318-11-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stable-dep-of: 9ce71e85b2 ("phy: renesas: rcar-gen3-usb2: Assert PLL reset on PHY power off")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 54c4c58713 upstream.
It has been observed on the Renesas RZ/G3S SoC that unbinding and binding
the PHY driver leads to role autodetection failures. This issue occurs when
PHY 3 is the first initialized PHY. PHY 3 does not have an interrupt
associated with the USB2_INT_ENABLE register (as
rcar_gen3_int_enable[3] = 0). As a result, rcar_gen3_init_otg() is called
to initialize OTG without enabling PHY interrupts.
To resolve this, add rcar_gen3_is_any_otg_rphy_initialized() and call it in
role_store(), role_show(), and rcar_gen3_init_otg(). At the same time,
rcar_gen3_init_otg() is only called when initialization for a PHY with
interrupt bits is in progress. As a result, the
struct rcar_gen3_phy::otg_initialized is no longer needed.
Fixes: 549b6b55b0 ("phy: renesas: rcar-gen3-usb2: enable/disable independent irqs")
Cc: stable@vger.kernel.org
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250507125032.565017-2-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2ea5f4958 upstream.
If device_add() fails, do not use device_unregister() for error
handling. device_unregister() consists two functions: device_del() and
put_device(). device_unregister() should only be called after
device_add() succeeded because device_del() undoes what device_add()
does if successful. Change device_unregister() to put_device() call
before returning from the function.
As comment of device_add() says, 'if device_add() succeeds, you should
call device_del() when you want to get rid of it. If device_add() has
not succeeded, use only put_device() to drop the reference count'.
Found by code review.
Cc: stable@vger.kernel.org
Fixes: 53d2a715c2 ("phy: Add Tegra XUSB pad controller support")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20250303072739.3874987-1-make24@iscas.ac.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b47158fb42 upstream.
The current implementation uses bias_pad_enable as a reference count to
manage the shared bias pad for all UTMI PHYs. However, during system
suspension with connected USB devices, multiple power-down requests for
the UTMI pad result in a mismatch in the reference count, which in turn
produces warnings such as:
[ 237.762967] WARNING: CPU: 10 PID: 1618 at tegra186_utmi_pad_power_down+0x160/0x170
[ 237.763103] Call trace:
[ 237.763104] tegra186_utmi_pad_power_down+0x160/0x170
[ 237.763107] tegra186_utmi_phy_power_off+0x10/0x30
[ 237.763110] phy_power_off+0x48/0x100
[ 237.763113] tegra_xusb_enter_elpg+0x204/0x500
[ 237.763119] tegra_xusb_suspend+0x48/0x140
[ 237.763122] platform_pm_suspend+0x2c/0xb0
[ 237.763125] dpm_run_callback.isra.0+0x20/0xa0
[ 237.763127] __device_suspend+0x118/0x330
[ 237.763129] dpm_suspend+0x10c/0x1f0
[ 237.763130] dpm_suspend_start+0x88/0xb0
[ 237.763132] suspend_devices_and_enter+0x120/0x500
[ 237.763135] pm_suspend+0x1ec/0x270
The root cause was traced back to the dynamic power-down changes
introduced in commit a30951d31b ("xhci: tegra: USB2 pad power controls"),
where the UTMI pad was being powered down without verifying its current
state. This unbalanced behavior led to discrepancies in the reference
count.
To rectify this issue, this patch replaces the single reference counter
with a bitmask, renamed to utmi_pad_enabled. Each bit in the mask
corresponds to one of the four USB2 PHYs, allowing us to track each pad's
enablement status individually.
With this change:
- The bias pad is powered on only when the mask is clear.
- Each UTMI pad is powered on or down based on its corresponding bit
in the mask, preventing redundant operations.
- The overall power state of the shared bias pad is maintained
correctly during suspend/resume cycles.
The mutex used to prevent race conditions during UTMI pad enable/disable
operations has been moved from the tegra186_utmi_bias_pad_power_on/off
functions to the parent functions tegra186_utmi_pad_power_on/down. This
change ensures that there are no race conditions when updating the bitmask.
Cc: stable@vger.kernel.org
Fixes: a30951d31b ("xhci: tegra: USB2 pad power controls")
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20250408030905.990474-1-waynec@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aecb63e88c upstream.
Ensure the PHY reset and perst is asserted during power-off to
guarantee it is in a reset state upon repeated power-on calls. This
resolves an issue where the PHY may not properly initialize during
subsequent power-on cycles. Power-on will deassert the reset at the
appropriate time after tuning the PHY parameters.
During suspend/resume cycles, we observed that the PHY PLL failed to
lock during resume when the CPU temperature increased from 65C to 75C.
The observed errors were:
phy phy-32f00000.pcie-phy.3: phy poweron failed --> -110
imx6q-pcie 33800000.pcie: waiting for PHY ready timeout!
imx6q-pcie 33800000.pcie: PM: dpm_run_callback(): genpd_resume_noirq+0x0/0x80 returns -110
imx6q-pcie 33800000.pcie: PM: failed to resume noirq: error -110
This resulted in a complete CPU freeze, which is resolved by ensuring
the PHY is in reset during power-on, thus preventing PHY PLL failures.
Cc: stable@vger.kernel.org
Fixes: 1aa97b0022 ("phy: freescale: pcie: Initialize the imx8 pcie standalone phy driver")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250305144355.20364-3-eichest@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55f1a5f7c9 upstream.
Observed VBUS_OVERRIDE & ID_OVERRIDE might be programmed
with unexpected value prior to XUSB PADCTL driver, this
could also occur in virtualization scenario.
For example, UEFI firmware programs ID_OVERRIDE=GROUNDED to set
a type-c port to host mode and keeps the value to kernel.
If the type-c port is connected a usb host, below errors can be
observed right after usb host mode driver gets probed. The errors
would keep until usb role class driver detects the type-c port
as device mode and notifies usb device mode driver to set both
ID_OVERRIDE and VBUS_OVERRIDE to correct value by XUSB PADCTL
driver.
[ 173.765814] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[ 173.765837] usb usb3-port2: config error
Taking virtualization into account, asserting XUSB PADCTL
reset would break XUSB functions used by other guest OS,
hence only reset VBUS & ID OVERRIDE of the port in
utmi_phy_init.
Fixes: bbf711682c ("phy: tegra: xusb: Add Tegra186 support")
Cc: stable@vger.kernel.org
Change-Id: Ic63058d4d49b4a1f8f9ab313196e20ad131cc591
Signed-off-by: BH Hsieh <bhsieh@nvidia.com>
Signed-off-by: Henry Lin <henryl@nvidia.com>
Link: https://lore.kernel.org/r/20250122105943.8057-1-henryl@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fbcbffbac9 upstream.
Currently, the USB port via combophy on the RK3528/RK3588 SoC is broken.
usb usb8-port1: Cannot enable. Maybe the USB cable is bad?
This is due to the combphy of RK3528/RK3588 SoC has multiple resets, but
only "phy resets" need assert and deassert, "apb resets" don't need.
So change the driver to only match the phy resets, which is also what
the vendor kernel does.
Fixes: 7160820d74 ("phy: rockchip: add naneng combo phy for RK3568")
Cc: FUKAUMI Naoki <naoki@radxa.com>
Cc: Michael Zimmermann <sigmaepsilon92@gmail.com>
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20241122073006.99309-2-amadeus@jmu.edu.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4dc48c88fc upstream.
For devm_phy_destroy(), its comment says it needs to invoke phy_destroy()
to destroy the phy, but it will not actually invoke the function since
devres_destroy() does not call devm_phy_consume(), and the missing
phy_destroy() call will cause that the phy fails to be destroyed.
Fortunately, the faulty API has not been used by current kernel tree.
Fix by using devres_release() instead of devres_destroy() within the API.
Fixes: ff76496347 ("drivers: phy: add generic PHY framework")
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20241213-phy_core_fix-v6-3-40ae28f5015a@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe4bfa9b6d upstream.
For devm_phy_put(), its comment says it needs to invoke phy_put() to
release the phy, but it will not actually invoke the function since
devres_destroy() does not call devm_phy_release(), and the missing
phy_put() call will cause:
- The phy fails to be released.
- devm_phy_put() can not fully undo what API devm_phy_get() does.
- Leak refcount of both the module and device for below typical usage:
devm_phy_get(); // or its variant
...
err = do_something();
if (err)
goto err_out;
...
err_out:
devm_phy_put(); // leak refcount here
The file(s) affected by this issue are shown below since they have such
typical usage.
drivers/pci/controller/cadence/pcie-cadence.c
drivers/net/ethernet/ti/am65-cpsw-nuss.c
Fix by using devres_release() instead of devres_destroy() within the API.
Fixes: ff76496347 ("drivers: phy: add generic PHY framework")
Cc: stable@vger.kernel.org
Cc: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: Krzysztof Wilczyński <kw@linux.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20241213-phy_core_fix-v6-1-40ae28f5015a@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a2d633cb14 upstream.
For macro for_each_child_of_node(parent, child), refcount of @child has
been increased before entering its loop body, so normally needs to call
of_node_put(@child) before returning from the loop body to avoid refcount
leakage.
of_phy_provider_lookup() has such usage but does not call of_node_put()
before returning, so cause leakage of the OF node refcount.
Fix by simply calling of_node_put() before returning from the loop body.
The APIs affected by this issue are shown below since they indirectly
invoke problematic of_phy_provider_lookup().
phy_get()
of_phy_get()
devm_phy_get()
devm_of_phy_get()
devm_of_phy_get_by_index()
Fixes: 2a4c37016c ("phy: core: Fix of_phy_provider_lookup to return PHY provider for sub node")
Cc: stable@vger.kernel.org
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20241213-phy_core_fix-v6-5-40ae28f5015a@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f89263b697 ]
When enable initcall_debug together with higher debug level below.
CONFIG_CONSOLE_LOGLEVEL_DEFAULT=9
CONFIG_CONSOLE_LOGLEVEL_QUIET=9
CONFIG_MESSAGE_LOGLEVEL_DEFAULT=7
The initialization of i.MX8MP PCIe PHY might be timeout failed randomly.
To fix this issue, adjust the sequence of the resets refer to the power
up sequence listed below.
i.MX8MP PCIe PHY power up sequence:
/---------------------------------------------
1.8v supply ---------/
/---------------------------------------------------
0.8v supply ---/
---\ /--------------------------------------------------
X REFCLK Valid
Reference Clock ---/ \--------------------------------------------------
-------------------------------------------
|
i_init_restn --------------
------------------------------------
|
i_cmn_rstn ---------------------
-------------------------------
|
o_pll_lock_done --------------------------
Logs:
imx6q-pcie 33800000.pcie: host bridge /soc@0/pcie@33800000 ranges:
imx6q-pcie 33800000.pcie: IO 0x001ff80000..0x001ff8ffff -> 0x0000000000
imx6q-pcie 33800000.pcie: MEM 0x0018000000..0x001fefffff -> 0x0018000000
probe of clk_imx8mp_audiomix.reset.0 returned 0 after 1052 usecs
probe of 30e20000.clock-controller returned 0 after 32971 usecs
phy phy-32f00000.pcie-phy.4: phy poweron failed --> -110
probe of 30e10000.dma-controller returned 0 after 10235 usecs
imx6q-pcie 33800000.pcie: waiting for PHY ready timeout!
dwhdmi-imx 32fd8000.hdmi: Detected HDMI TX controller v2.13a with HDCP (samsung_dw_hdmi_phy2)
imx6q-pcie 33800000.pcie: probe with driver imx6q-pcie failed with error -110
Fixes: dce9edff16 ("phy: freescale: imx8m-pcie: Add i.MX8MP PCIe PHY support")
Cc: stable@vger.kernel.org
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
v2 changes:
- Rebase to latest fixes branch of linux-phy git repo.
- Richard's environment have problem and can't sent out patch. So I help
post this fix patch.
Link: https://lore.kernel.org/r/20241021155241.943665-1-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 29240130ab upstream.
Commit 413db06c05 ("phy: qcom-qmp-usb: clean up probe initialisation")
removed most users of the platform device driver data from the
qcom-qmp-usb driver, but mistakenly also removed the initialisation
despite the data still being used in the runtime PM callbacks. This bug
was later reproduced when the driver was copied to create the
qmp-usb-legacy driver.
Restore the driver data initialisation at probe to avoid a NULL-pointer
dereference on runtime suspend.
Apparently no one uses runtime PM, which currently needs to be enabled
manually through sysfs, with these drivers.
Fixes: e464a3180a ("phy: qcom-qmp-usb: split off the legacy USB+dp_com support")
Cc: stable@vger.kernel.org # 6.6
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240911115253.10920-3-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd9e4d4a3b upstream.
Commit 413db06c05 ("phy: qcom-qmp-usb: clean up probe initialisation")
removed most users of the platform device driver data, but mistakenly
also removed the initialisation despite the data still being used in the
runtime PM callbacks.
Restore the driver data initialisation at probe to avoid a NULL-pointer
dereference on runtime suspend.
Apparently no one uses runtime PM, which currently needs to be enabled
manually through sysfs, with this driver.
Fixes: 413db06c05 ("phy: qcom-qmp-usb: clean up probe initialisation")
Cc: stable@vger.kernel.org # 6.2
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240911115253.10920-2-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d79c684091 ]
Take the phy mutex in xlate to protect against concurrent
modification/access to gtr_phy. This does not typically cause any
issues, since in most systems the phys are only xlated once and
thereafter accessed with the phy API (which takes the locks). However,
we are about to allow userspace to access phys for debugging, so it's
important to avoid any data races.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://lore.kernel.org/r/20240628205540.3098010-5-sean.anderson@linux.dev
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5af9b304bc ]
On a few Kria KR260 Robotics Starter Kit the PS-GEM SGMII linkup is not
happening after the resume. This is because serdes registers are reset
when FPD is off (in suspend state) and needs to be reprogrammed in the
resume path with the same default initialization as done in the first
stage bootloader psu_init routine.
To address the failure introduce a set of serdes registers to be saved in
the suspend path and then restore it on resume.
Fixes: 4a33bea003 ("phy: zynqmp: Add PHY driver for the Xilinx ZynqMP Gigabit Transceiver")
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1722837547-2578381-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
