[ Upstream commit 41307ec7df ]
The X1E80100 battery management firmware sends a notification with
code 0x83 when the battery charging state changes, such as switching
between fast charge, taper charge, end of charge, or any other error
charging states.
The same notification code is used with bit[8] set when charging stops
because the charge control end threshold is reached. Additionally,
a 2-bit value is included in bit[10:9] with the same code to indicate
the charging source capability, which is determined by the calculated
power from voltage and current readings from PDOs: 2 means a strong
charger over 60W, 1 indicates a weak charger, and 0 means there is no
charging source.
These 3-MSB [10:8] in the notification code is not much useful for now,
hence just ignore them and trigger a power supply change event whenever
0x83 notification code is received. This helps to eliminate the unknown
notification error messages.
Reported-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Closes: https://lore.kernel.org/all/r65idyc4of5obo6untebw4iqfj2zteiggnnzabrqtlcinvtddx@xc4aig5abesu/
Signed-off-by: Fenglin Wu <fenglin.wu@oss.qualcomm.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ee6cd8f3e2 upstream.
CHARGE_CONTROL_LIMIT is a wrong property to report charge current limit,
because `CHARGE_*` attributes represents capacity, not current. The
correct attribute to report and set charge current limit is
CONSTANT_CHARGE_CURRENT.
Rename CHARGE_CONTROL_LIMIT to CONSTANT_CHARGE_CURRENT.
Cc: stable@vger.kernel.org
Fixes: 715ecbc10d ("power: supply: max77976: add Maxim MAX77976 charger driver")
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit def5612170 ]
Fix the checkpatch warning:
CHECK: Alignment should match open parenthesis
Fixes: 0cb172a491 ("power: supply: cw2015: Use device managed API to simplify the code")
Signed-off-by: Andy Yan <andyshrk@163.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2c334d0384 upstream.
Since commit
commit f16d9fb6cf ("power: supply: bq27xxx: Retrieve again when busy")
the console log of some devices with hdq enabled but no bq27000 battery
(like e.g. the Pandaboard) is flooded with messages like:
[ 34.247833] power_supply bq27000-battery: driver failed to report 'status' property: -1
as soon as user-space is finding a /sys entry and trying to read the
"status" property.
It turns out that the offending commit changes the logic to now return the
value of cache.flags if it is <0. This is likely under the assumption that
it is an error number. In normal errors from bq27xxx_read() this is indeed
the case.
But there is special code to detect if no bq27000 is installed or accessible
through hdq/1wire and wants to report this. In that case, the cache.flags
are set historically by
commit 3dd843e1c2 ("bq27000: report missing device better.")
to constant -1 which did make reading properties return -ENODEV. So everything
appeared to be fine before the return value was passed upwards.
Now the -1 is returned as -EPERM instead of -ENODEV, triggering the error
condition in power_supply_format_property() which then floods the console log.
So we change the detection of missing bq27000 battery to simply set
cache.flags = -ENODEV
instead of -1.
Fixes: f16d9fb6cf ("power: supply: bq27xxx: Retrieve again when busy")
Cc: Jerry Lv <Jerry.Lv@axis.com>
Cc: stable@vger.kernel.org
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Link: https://lore.kernel.org/r/692f79eb6fd541adb397038ea6e750d4de2deddf.1755945297.git.hns@goldelico.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f16d9fb6cf ]
Multiple applications may access the battery gauge at the same time, so
the gauge may be busy and EBUSY will be returned. The driver will set a
flag to record the EBUSY state, and this flag will be kept until the next
periodic update. When this flag is set, bq27xxx_battery_get_property()
will just return ENODEV until the flag is updated.
Even if the gauge was busy during the last accessing attempt, returning
ENODEV is not ideal, and can cause confusion in the applications layer.
Instead, retry accessing the I2C to update the flag is as expected, for
the gauge typically recovers from busy state within a few milliseconds.
If still failed to access the gauge, the real error code would be returned
instead of ENODEV (as suggested by Pali Rohár).
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Jerry Lv <Jerry.Lv@axis.com>
Link: https://lore.kernel.org/r/20250415-foo-fix-v2-1-5b45a395e4cc@axis.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30cc7b0d0e ]
The charge input threshold voltage register on the MAX77693 PMIC accepts
four values: 0x0 for 4.3v, 0x1 for 4.7v, 0x2 for 4.8v and 0x3 for 4.9v.
Due to an oversight, the driver calculated the values for 4.7v and above
starting from 0x0, rather than from 0x1 ([(4700000 - 4700000) / 100000]
gives 0).
Add 1 to the calculation to ensure that 4.7v is converted to a register
value of 0x1 and that the other two voltages are converted correctly as
well.
Fixes: 87c2d90678 ("power: max77693: Add charger driver for Maxim 77693")
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250316-max77693-charger-input-threshold-fix-v1-1-2b037d0ac722@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3fb3cb4350 ]
Size of variable sd_gain equals four bytes - DA9150_QIF_SD_GAIN_SIZE.
Size of variable shunt_val equals two bytes - DA9150_QIF_SHUNT_VAL_SIZE.
The expression sd_gain * shunt_val is currently being evaluated using
32-bit arithmetic. So during the multiplication an overflow may occur.
As the value of type 'u64' is used as storage for the eventual result, put
ULL variable at the first position of each expression in order to give the
compiler complete information about the proper arithmetic to use. According
to C99 the guaranteed width for a variable of type 'unsigned long long' >=
64 bits.
Remove the explicit cast to u64 as it is meaningless.
Just for the sake of consistency, perform the similar trick with another
expression concerning 'iavg'.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: a419b4fd91 ("power: Add support for DA9150 Fuel-Gauge")
Signed-off-by: Andrey Vatoropin <a.vatoropin@crpt.ru>
Link: https://lore.kernel.org/r/20250130090030.53422-1-a.vatoropin@crpt.ru
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6da4553ff ]
The put_device() call in power_supply_put() may call
power_supply_dev_release(). The latter function does not sleep so
power_supply_put() doesn't sleep either. Hence, remove the might_sleep()
call from power_supply_put(). This patch suppresses false positive
complaints about calling a sleeping function from atomic context if
power_supply_put() is called from atomic context.
Cc: Kyle Tso <kyletso@google.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Fixes: 1a352462b5 ("power_supply: Add power_supply_put for decrementing device reference counter")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240917193914.47566-1-bvanassche@acm.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e50a57d16f upstream.
Temp channel 0 aka temp1 can have a temp1_max_alarm attribute for
power_supply devices which have a POWER_SUPPLY_PROP_TEMP_ALERT_MAX
property.
HWMON_T_MAX_ALARM was missing from power_supply_hwmon_info for
temp channel 0, causing the hwmon temp1_max_alarm attribute to be
missing from such power_supply devices.
Add this to power_supply_hwmon_info to fix this.
Fixes: f1d33ae806 ("power: supply: remove duplicated argument in power_supply_hwmon_info")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240908185337.103696-2-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3a3acf839b ]
Commit 223a3b8283 ("power: supply: max17042_battery: use VFSOC for
capacity when no rsns") made it so that capacity on systems without
current sensing would be read from VFSOC instead of RepSOC. However,
the SOC threshold calculation still read RepSOC to get the SOC
regardless of the current sensing option state.
Fix this by applying the same conditional to determine which register
should be read.
This also seems to be the intended behavior as per the datasheet - SOC
alert config value in MiscCFG on setups without current sensing is set
to a value of 0b11, indicating SOC alerts being generated based on
VFSOC, instead of 0b00 which indicates SOC alerts being generated based
on RepSOC.
This fixes an issue on the Galaxy S3/Midas boards, where the alert
interrupt would be constantly retriggered, causing high CPU usage
on idle (around ~12%-15%).
Fixes: e5f3872d20 ("max17042: Add support for signalling change in SOC")
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240817-max17042-soc-threshold-fix-v1-1-72b45899c3cc@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e0fb11364 ]
The of_match shall correspond to the name of the regulator subnode,
or the deprecated `regulator-compatible` property must be used:
failing to do so, the regulator won't probe (and the driver will
as well not probe).
Since the devicetree binding for this driver is actually correct
and wants DTs to use the "usb-otg-vbus-regulator" subnode name,
fix this driver by aligning the `of_match` string to what the DT
binding wants.
Fixes: 0402e8ebb8 ("power: supply: mt6360_charger: add MT6360 charger support")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20240410084405.1389378-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 452d8950db ]
The rt9455_boost_voltage_values[] array is only used when USB PHY
support is enabled, causing a W=1 warning otherwise:
drivers/power/supply/rt9455_charger.c:200:18: error: 'rt9455_boost_voltage_values' defined but not used [-Werror=unused-const-variable=]
Enclose the definition in the same #ifdef as the references to it.
Fixes: e86d69dd78 ("power_supply: Add support for Richtek RT9455 battery charger")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240403080702.3509288-10-arnd@kernel.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2df70149e7 ]
The bq27xxx i2c-client may not have an IRQ, in which case
client->irq will be 0. bq27xxx_battery_i2c_probe() already has
an if (client->irq) check wrapping the request_threaded_irq().
But bq27xxx_battery_i2c_remove() unconditionally calls
free_irq(client->irq) leading to:
[ 190.310742] ------------[ cut here ]------------
[ 190.310843] Trying to free already-free IRQ 0
[ 190.310861] WARNING: CPU: 2 PID: 1304 at kernel/irq/manage.c:1893 free_irq+0x1b8/0x310
Followed by a backtrace when unbinding the driver. Add
an if (client->irq) to bq27xxx_battery_i2c_remove() mirroring
probe() to fix this.
Fixes: 444ff00734 ("power: supply: bq27xxx: Fix I2C IRQ race on remove")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240215155133.70537-1-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b55d073e65 ]
smatch complains that there is a buffer overflow and clang complains
'ret' is never read.
Smatch error:
drivers/power/supply/bq256xx_charger.c:1578 bq256xx_hw_init() error:
buffer overflow 'bq256xx_watchdog_time' 4 <= 4
Clang static checker:
Value stored to 'ret' is never read.
Add check for buffer overflow and error code from regmap_update_bits().
Fixes: 32e4978bb9 ("power: supply: bq256xx: Introduce the BQ256XX charger driver")
Signed-off-by: Su Hui <suhui@nfschina.com>
Link: https://lore.kernel.org/r/20231116041822.1378758-1-suhui@nfschina.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
power_supply_uevent() which is called to emit a udev event on device
deletion attempts to use the power_supply_battery_info structure,
which is device-managed and has been freed before this point.
Fix this by not generating all battery/charger properties when the
device is about to be removed. This also avoids generating errors
when trying to access the hardware in hot-unplug scenarios.
==================================================================
BUG: KASAN: slab-use-after-free in power_supply_battery_info_has_prop (power_supply_core.c:872)
Read of size 4 at addr 0000000062e59028 by task python3/27
Call Trace:
power_supply_battery_info_has_prop (power_supply_core.c:872)
power_supply_uevent (power_supply_sysfs.c:504)
dev_uevent (drivers/base/core.c:2590)
kobject_uevent_env (lib/kobject_uevent.c:558)
kobject_uevent (lib/kobject_uevent.c:643)
device_del (drivers/base/core.c:3266 drivers/base/core.c:3831)
device_unregister (drivers/base/core.c:3730 drivers/base/core.c:3854)
power_supply_unregister (power_supply_core.c:1608)
devm_power_supply_release (power_supply_core.c:1515)
release_nodes (drivers/base/devres.c:506)
devres_release_group (drivers/base/devres.c:669)
i2c_device_remove (drivers/i2c/i2c-core-base.c:629)
device_remove (drivers/base/dd.c:570)
device_release_driver_internal (drivers/base/dd.c:1274 drivers/base/dd.c:1295)
device_driver_detach (drivers/base/dd.c:1332)
unbind_store (drivers/base/bus.c:247)
...
Allocated by task 27:
devm_kmalloc (drivers/base/devres.c:119 drivers/base/devres.c:829)
power_supply_get_battery_info (include/linux/device.h:316 power_supply_core.c:626)
__power_supply_register (power_supply_core.c:1408)
devm_power_supply_register (power_supply_core.c:1544)
bq256xx_probe (bq256xx_charger.c:1539 bq256xx_charger.c:1727) bq256xx_charger
i2c_device_probe (drivers/i2c/i2c-core-base.c:584)
really_probe (drivers/base/dd.c:579 drivers/base/dd.c:658)
__driver_probe_device (drivers/base/dd.c:800)
device_driver_attach (drivers/base/dd.c:1128)
bind_store (drivers/base/bus.c:273)
...
Freed by task 27:
kfree (mm/slab_common.c:1073)
release_nodes (drivers/base/devres.c:503)
devres_release_all (drivers/base/devres.c:536)
device_del (drivers/base/core.c:3829)
device_unregister (drivers/base/core.c:3730 drivers/base/core.c:3854)
power_supply_unregister (power_supply_core.c:1608)
devm_power_supply_release (power_supply_core.c:1515)
release_nodes (drivers/base/devres.c:506)
devres_release_group (drivers/base/devres.c:669)
i2c_device_remove (drivers/i2c/i2c-core-base.c:629)
device_remove (drivers/base/dd.c:570)
device_release_driver_internal (drivers/base/dd.c:1274 drivers/base/dd.c:1295)
device_driver_detach (drivers/base/dd.c:1332)
unbind_store (drivers/base/bus.c:247)
...
==================================================================
Reported-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Fixes: 27a2195efa ("power: supply: core: auto-exposure of simple-battery data")
Tested-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
When building with clang 18 I see the following warning:
| drivers/power/reset/vexpress-poweroff.c:124:10: warning: cast to smaller integer type 'enum vexpress_reset_func' from 'const void *' [-Wvoid-pointer-to-enum-cast]
| 124 | switch ((enum vexpress_reset_func)match->data) {
This is due to the fact that `match->data` is a void* while `enum vexpress_reset_func`
has the size of an int. This leads to truncation and possible data loss.
Link: https://github.com/ClangBuiltLinux/linux/issues/1910
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Justin Stitt <justinstitt@google.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
