[ Upstream commit d946f3c983 ]
The bpf_skb_check_mtu helper needs to use skb->transport_header when
the BPF_MTU_CHK_SEGS flag is used:
bpf_skb_check_mtu(skb, ifindex, &mtu_len, 0, BPF_MTU_CHK_SEGS)
The transport_header is not always set. There is a WARN_ON_ONCE
report when CONFIG_DEBUG_NET is enabled + skb->gso_size is set +
bpf_prog_test_run is used:
WARNING: CPU: 1 PID: 2216 at ./include/linux/skbuff.h:3071
skb_gso_validate_network_len
bpf_skb_check_mtu
bpf_prog_3920e25740a41171_tc_chk_segs_flag # A test in the next patch
bpf_test_run
bpf_prog_test_run_skb
For a normal ingress skb (not test_run), skb_reset_transport_header
is performed but there is plan to avoid setting it as described in
commit 2170a1f091 ("net: no longer reset transport_header in __netif_receive_skb_core()").
This patch fixes the bpf helper by checking
skb_transport_header_was_set(). The check is done just before
skb->transport_header is used, to avoid breaking the existing bpf prog.
The WARN_ON_ONCE is limited to bpf_prog_test_run, so targeting bpf-next.
Fixes: 34b2021cc6 ("bpf: Add BPF-helper for MTU checking")
Cc: Jesper Dangaard Brouer <hawk@kernel.org>
Reported-by: Kaiyan Mei <M202472210@hust.edu.cn>
Reported-by: Yinhao Hu <dddddd@hust.edu.cn>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://lore.kernel.org/r/20251112232331.1566074-1-martin.lau@linux.dev
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f0d0277796 upstream.
When __netpoll_setup() is called directly, instead of through
netpoll_setup(), the np->skb_pool list head isn't initialized.
If skb_pool_flush() is later called, then we hit a NULL pointer
in skb_queue_purge_reason(). This can be seen with this repro,
when CONFIG_NETCONSOLE is enabled as a module:
ip tuntap add mode tap tap0
ip link add name br0 type bridge
ip link set dev tap0 master br0
modprobe netconsole netconsole=4444@10.0.0.1/br0,9353@10.0.0.2/
rmmod netconsole
The backtrace is:
BUG: kernel NULL pointer dereference, address: 0000000000000008
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
... ... ...
Call Trace:
<TASK>
__netpoll_free+0xa5/0xf0
br_netpoll_cleanup+0x43/0x50 [bridge]
do_netpoll_cleanup+0x43/0xc0
netconsole_netdev_event+0x1e3/0x300 [netconsole]
unregister_netdevice_notifier+0xd9/0x150
cleanup_module+0x45/0x920 [netconsole]
__se_sys_delete_module+0x205/0x290
do_syscall_64+0x70/0x150
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Move the skb_pool list setup and initial skb fill into __netpoll_setup().
Fixes: 221a9c1df7 ("net: netpoll: Individualize the skb pool")
Signed-off-by: John Sperbeck <jsperbeck@google.com>
Reviewed-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20250114011354.2096812-1-jsperbeck@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 49c8d2c1f9 ]
commit efa95b01da ("netpoll: fix use after free") incorrectly
ignored the refcount and prematurely set dev->npinfo to NULL during
netpoll cleanup, leading to improper behavior and memory leaks.
Scenario causing lack of proper cleanup:
1) A netpoll is associated with a NIC (e.g., eth0) and netdev->npinfo is
allocated, and refcnt = 1
- Keep in mind that npinfo is shared among all netpoll instances. In
this case, there is just one.
2) Another netpoll is also associated with the same NIC and
npinfo->refcnt += 1.
- Now dev->npinfo->refcnt = 2;
- There is just one npinfo associated to the netdev.
3) When the first netpolls goes to clean up:
- The first cleanup succeeds and clears np->dev->npinfo, ignoring
refcnt.
- It basically calls `RCU_INIT_POINTER(np->dev->npinfo, NULL);`
- Set dev->npinfo = NULL, without proper cleanup
- No ->ndo_netpoll_cleanup() is either called
4) Now the second target tries to clean up
- The second cleanup fails because np->dev->npinfo is already NULL.
* In this case, ops->ndo_netpoll_cleanup() was never called, and
the skb pool is not cleaned as well (for the second netpoll
instance)
- This leaks npinfo and skbpool skbs, which is clearly reported by
kmemleak.
Revert commit efa95b01da ("netpoll: fix use after free") and adds
clarifying comments emphasizing that npinfo cleanup should only happen
once the refcount reaches zero, ensuring stable and correct netpoll
behavior.
Cc: <stable@vger.kernel.org> # 3.17.x
Cc: Jay Vosburgh <jv@jvosburgh.net>
Fixes: efa95b01da ("netpoll: fix use after free")
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251107-netconsole_torture-v10-1-749227b55f63@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6c59f16f17 ]
The netpoll subsystem maintains a pool of 32 pre-allocated SKBs per
instance, but these SKBs are not freed when the netpoll user is brought
down. This leads to memory waste as these buffers remain allocated but
unused.
Add skb_pool_flush() to properly clean up these SKBs when netconsole is
terminated, improving memory efficiency.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20241114-skb_buffers_v2-v3-2-9be9f52a8b69@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 49c8d2c1f9 ("net: netpoll: fix incorrect refcount handling causing incorrect cleanup")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 221a9c1df7 ]
The current implementation of the netpoll system uses a global skb
pool, which can lead to inefficient memory usage and
waste when targets are disabled or no longer in use.
This can result in a significant amount of memory being unnecessarily
allocated and retained, potentially causing performance issues and
limiting the availability of resources for other system components.
Modify the netpoll system to assign a skb pool to each target instead of
using a global one.
This approach allows for more fine-grained control over memory
allocation and deallocation, ensuring that resources are only allocated
and retained as needed.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20241114-skb_buffers_v2-v3-1-9be9f52a8b69@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 49c8d2c1f9 ("net: netpoll: fix incorrect refcount handling causing incorrect cleanup")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9a95eedc81 ]
netpoll_srcu is currently used from netpoll_poll_disable() and
__netpoll_cleanup()
Both functions run under RTNL, using netpoll_srcu adds confusion
and no additional protection.
Moreover the synchronize_srcu() call in __netpoll_cleanup() is
performed before clearing np->dev->npinfo, which violates RCU rules.
After this patch, netpoll_poll_disable() and netpoll_poll_enable()
simply use rtnl_dereference().
This saves a big chunk of memory (more than 192KB on platforms
with 512 cpus)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20240905084909.2082486-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 49c8d2c1f9 ("net: netpoll: fix incorrect refcount handling causing incorrect cleanup")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 14ad6ed30a ]
Sabrina reported the following splat:
WARNING: CPU: 0 PID: 1 at net/core/dev.c:6935 netif_napi_add_weight_locked+0x8f2/0xba0
Modules linked in:
CPU: 0 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.14.0-rc1-net-00092-g011b03359038 #996
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Arch Linux 1.16.3-1-1 04/01/2014
RIP: 0010:netif_napi_add_weight_locked+0x8f2/0xba0
Code: e8 c3 e6 6a fe 48 83 c4 28 5b 5d 41 5c 41 5d 41 5e 41 5f c3 cc cc cc cc c7 44 24 10 ff ff ff ff e9 8f fb ff ff e8 9e e6 6a fe <0f> 0b e9 d3 fe ff ff e8 92 e6 6a fe 48 8b 04 24 be ff ff ff ff 48
RSP: 0000:ffffc9000001fc60 EFLAGS: 00010293
RAX: 0000000000000000 RBX: ffff88806ce48128 RCX: 1ffff11001664b9e
RDX: ffff888008f00040 RSI: ffffffff8317ca42 RDI: ffff88800b325cb6
RBP: ffff88800b325c40 R08: 0000000000000001 R09: ffffed100167502c
R10: ffff88800b3a8163 R11: 0000000000000000 R12: ffff88800ac1c168
R13: ffff88800ac1c168 R14: ffff88800ac1c168 R15: 0000000000000007
FS: 0000000000000000(0000) GS:ffff88806ce00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffff888008201000 CR3: 0000000004c94001 CR4: 0000000000370ef0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
gro_cells_init+0x1ba/0x270
xfrm_input_init+0x4b/0x2a0
xfrm_init+0x38/0x50
ip_rt_init+0x2d7/0x350
ip_init+0xf/0x20
inet_init+0x406/0x590
do_one_initcall+0x9d/0x2e0
do_initcalls+0x23b/0x280
kernel_init_freeable+0x445/0x490
kernel_init+0x20/0x1d0
ret_from_fork+0x46/0x80
ret_from_fork_asm+0x1a/0x30
</TASK>
irq event stamp: 584330
hardirqs last enabled at (584338): [<ffffffff8168bf87>] __up_console_sem+0x77/0xb0
hardirqs last disabled at (584345): [<ffffffff8168bf6c>] __up_console_sem+0x5c/0xb0
softirqs last enabled at (583242): [<ffffffff833ee96d>] netlink_insert+0x14d/0x470
softirqs last disabled at (583754): [<ffffffff8317c8cd>] netif_napi_add_weight_locked+0x77d/0xba0
on kernel built with MAX_SKB_FRAGS=45, where SKB_WITH_OVERHEAD(1024)
is smaller than GRO_MAX_HEAD.
Such built additionally contains the revert of the single page frag cache
so that napi_get_frags() ends up using the page frag allocator, triggering
the splat.
Note that the underlying issue is independent from the mentioned
revert; address it ensuring that the small head cache will fit either TCP
and GRO allocation and updating napi_alloc_skb() and __netdev_alloc_skb()
to select kmalloc() usage for any allocation fitting such cache.
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Suggested-by: Eric Dumazet <edumazet@google.com>
Fixes: 3948b05950 ("net: introduce a config option to tweak MAX_SKB_FRAGS")
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
[ Minor context change fixed. ]
Signed-off-by: Wenshan Lan <jetlan9@163.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3b52167a0 ]
Driver authors often forget to add GFP_NOWARN for page allocation
from the datapath. This is annoying to users as OOMs are a fact
of life, and we pretty much expect network Rx to hit page allocation
failures during OOM. Make page pool add GFP_NOWARN for ATOMIC allocations
by default.
Reviewed-by: Mina Almasry <almasrymina@google.com>
Link: https://patch.msgid.link/20250912161703.361272-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d85c565a7 ]
Initially, trace_sock_exceed_buf_limit() was invoked when
__sk_mem_raise_allocated() failed due to the memcg limit or the
global limit.
However, commit d6f19938eb ("net: expose sk wmem in
sock_exceed_buf_limit tracepoint") somehow suppressed the event
only when memcg failed to charge for SK_MEM_RECV, although the
memcg failure for SK_MEM_SEND still triggers the event.
Let's restore the event for SK_MEM_RECV.
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Shakeel Butt <shakeel.butt@linux.dev>
Link: https://patch.msgid.link/20250815201712.1745332-5-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f12d1137c ]
It is possible for bpf_xdp_adjust_tail() to free all fragments. The
kfunc currently clears the XDP_FLAGS_HAS_FRAGS bit, but not
XDP_FLAGS_FRAGS_PF_MEMALLOC. So far, this has not caused a issue when
building sk_buff from xdp_buff since all readers of xdp_buff->flags
use the flag only when there are fragments. Clear the
XDP_FLAGS_FRAGS_PF_MEMALLOC bit as well to make the flags correct.
Signed-off-by: Amery Hung <ameryhung@gmail.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://patch.msgid.link/20250922233356.3356453-2-ameryhung@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf29555f5b ]
Creating FDB entries is possible from a non-initial user namespace when
having CAP_NET_ADMIN, yet, when deleting FDB entries, processes receive
an EPERM because the capability is always checked against the initial
user namespace. This restricts the FDB management from unprivileged
containers.
Drop the netlink_capable check in rtnl_fdb_del as it was originally
dropped in c5c351088a and reintroduced in 1690be63a2 without
intention.
This patch was tested using a container on GyroidOS, where it was
possible to delete FDB entries from an unprivileged user namespace and
private network namespace.
Fixes: 1690be63a2 ("bridge: Add vlan support to static neighbors")
Reviewed-by: Michael Weiß <michael.weiss@aisec.fraunhofer.de>
Tested-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Johannes Wiesböck <johannes.wiesboeck@aisec.fraunhofer.de>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20251015201548.319871-1-johannes.wiesboeck@aisec.fraunhofer.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23f3770e1a ]
Cilium has a BPF egress gateway feature which forces outgoing K8s Pod
traffic to pass through dedicated egress gateways which then SNAT the
traffic in order to interact with stable IPs outside the cluster.
The traffic is directed to the gateway via vxlan tunnel in collect md
mode. A recent BPF change utilized the bpf_redirect_neigh() helper to
forward packets after the arrival and decap on vxlan, which turned out
over time that the kmalloc-256 slab usage in kernel was ever-increasing.
The issue was that vxlan allocates the metadata_dst object and attaches
it through a fake dst entry to the skb. The latter was never released
though given bpf_redirect_neigh() was merely setting the new dst entry
via skb_dst_set() without dropping an existing one first.
Fixes: b4ab314149 ("bpf: Add redirect_neigh helper as redirect drop-in")
Reported-by: Yusuke Suzuki <yusuke.suzuki@isovalent.com>
Reported-by: Julian Wiedmann <jwi@isovalent.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Martin KaFai Lau <martin.lau@kernel.org>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jordan Rife <jrife@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jordan Rife <jrife@google.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://lore.kernel.org/r/20251003073418.291171-1-daniel@iogearbox.net
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca9f9cdc4d ]
Currently, alloc_skb_with_frags() will only fill (MAX_SKB_FRAGS - 1)
slots. I think it should use all MAX_SKB_FRAGS slots, as callers of
alloc_skb_with_frags() will size their allocation of frags based
on MAX_SKB_FRAGS.
This issue was discovered via a test patch that sets 'order' to 0
in alloc_skb_with_frags(), which effectively tests/simulates high
fragmentation. In this case sendmsg() on unix sockets will fail every
time for large allocations. If the PAGE_SIZE is 4K, then data_len will
request 68K or 17 pages, but alloc_skb_with_frags() can only allocate
64K in this case or 16 pages.
Fixes: 09c2c90705 ("net: allow alloc_skb_with_frags() to allocate bigger packets")
Signed-off-by: Jason Baron <jbaron@akamai.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250922191957.2855612-1-jbaron@akamai.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 864e339697 ]
When performing Generic Segmentation Offload (GSO) on an IPv6 packet that
contains extension headers, the kernel incorrectly requests checksum offload
if the egress device only advertises NETIF_F_IPV6_CSUM feature, which has
a strict contract: it supports checksum offload only for plain TCP or UDP
over IPv6 and explicitly does not support packets with extension headers.
The current GSO logic violates this contract by failing to disable the feature
for packets with extension headers, such as those used in GREoIPv6 tunnels.
This violation results in the device being asked to perform an operation
it cannot support, leading to a `skb_warn_bad_offload` warning and a collapse
of network throughput. While device TSO/USO is correctly bypassed in favor
of software GSO for these packets, the GSO stack must be explicitly told not
to request checksum offload.
Mask NETIF_F_IPV6_CSUM, NETIF_F_TSO6 and NETIF_F_GSO_UDP_L4
in gso_features_check if the IPv6 header contains extension headers to compute
checksum in software.
The exception is a BIG TCP extension, which, as stated in commit
68e068cabd ("net: reenable NETIF_F_IPV6_CSUM offload for BIG TCP packets"):
"The feature is only enabled on devices that support BIG TCP TSO.
The header is only present for PF_PACKET taps like tcpdump,
and not transmitted by physical devices."
kernel log output (truncated):
WARNING: CPU: 1 PID: 5273 at net/core/dev.c:3535 skb_warn_bad_offload+0x81/0x140
...
Call Trace:
<TASK>
skb_checksum_help+0x12a/0x1f0
validate_xmit_skb+0x1a3/0x2d0
validate_xmit_skb_list+0x4f/0x80
sch_direct_xmit+0x1a2/0x380
__dev_xmit_skb+0x242/0x670
__dev_queue_xmit+0x3fc/0x7f0
ip6_finish_output2+0x25e/0x5d0
ip6_finish_output+0x1fc/0x3f0
ip6_tnl_xmit+0x608/0xc00 [ip6_tunnel]
ip6gre_tunnel_xmit+0x1c0/0x390 [ip6_gre]
dev_hard_start_xmit+0x63/0x1c0
__dev_queue_xmit+0x6d0/0x7f0
ip6_finish_output2+0x214/0x5d0
ip6_finish_output+0x1fc/0x3f0
ip6_xmit+0x2ca/0x6f0
ip6_finish_output+0x1fc/0x3f0
ip6_xmit+0x2ca/0x6f0
inet6_csk_xmit+0xeb/0x150
__tcp_transmit_skb+0x555/0xa80
tcp_write_xmit+0x32a/0xe90
tcp_sendmsg_locked+0x437/0x1110
tcp_sendmsg+0x2f/0x50
...
skb linear: 00000000: e4 3d 1a 7d ec 30 e4 3d 1a 7e 5d 90 86 dd 60 0e
skb linear: 00000010: 00 0a 1b 34 3c 40 20 11 00 00 00 00 00 00 00 00
skb linear: 00000020: 00 00 00 00 00 12 20 11 00 00 00 00 00 00 00 00
skb linear: 00000030: 00 00 00 00 00 11 2f 00 04 01 04 01 01 00 00 00
skb linear: 00000040: 86 dd 60 0e 00 0a 1b 00 06 40 20 23 00 00 00 00
skb linear: 00000050: 00 00 00 00 00 00 00 00 00 12 20 23 00 00 00 00
skb linear: 00000060: 00 00 00 00 00 00 00 00 00 11 bf 96 14 51 13 f9
skb linear: 00000070: ae 27 a0 a8 2b e3 80 18 00 40 5b 6f 00 00 01 01
skb linear: 00000080: 08 0a 42 d4 50 d5 4b 70 f8 1a
Fixes: 04c20a9356 ("net: skip offload for NETIF_F_IPV6_CSUM if ipv6 header contains extension")
Reported-by: Tianhao Zhao <tizhao@redhat.com>
Suggested-by: Michal Schmidt <mschmidt@redhat.com>
Suggested-by: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Signed-off-by: Jakub Ramaseuski <jramaseu@redhat.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250814105119.1525687-1-jramaseu@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2da4def0f4 ]
Paolo spotted hangs in NIPA running driver tests against virtio.
The tests hang in virtnet_close() -> virtnet_napi_tx_disable().
The problem is only reproducible if running multiple of our tests
in sequence (I used TEST_PROGS="xdp.py ping.py netcons_basic.sh \
netpoll_basic.py stats.py"). Initial suspicion was that this is
a simple case of double-disable of NAPI, but instrumenting the
code reveals:
Deadlocked on NAPI ffff888007cd82c0 (virtnet_poll_tx):
state: 0x37, disabled: false, owner: 0, listed: false, weight: 64
The NAPI was not in fact disabled, owner is 0 (rather than -1),
so the NAPI "thinks" it's scheduled for CPU 0 but it's not listed
(!list_empty(&n->poll_list) => false). It seems odd that normal NAPI
processing would wedge itself like this.
Better suspicion is that netpoll gets enabled while NAPI is polling,
and also grabs the NAPI instance. This confuses napi_complete_done():
[netpoll] [normal NAPI]
napi_poll()
have = netpoll_poll_lock()
rcu_access_pointer(dev->npinfo)
return NULL # no netpoll
__napi_poll()
->poll(->weight)
poll_napi()
cmpxchg(->poll_owner, -1, cpu)
poll_one_napi()
set_bit(NAPI_STATE_NPSVC, ->state)
napi_complete_done()
if (NAPIF_STATE_NPSVC)
return false
# exit without clearing SCHED
This feels very unlikely, but perhaps virtio has some interactions
with the hypervisor in the NAPI ->poll that makes the race window
larger?
Best I could to to prove the theory was to add and trigger this
warning in napi_poll (just before netpoll_poll_unlock()):
WARN_ONCE(!have && rcu_access_pointer(n->dev->npinfo) &&
napi_is_scheduled(n) && list_empty(&n->poll_list),
"NAPI race with netpoll %px", n);
If this warning hits the next virtio_close() will hang.
This patch survived 30 test iterations without a hang (without it
the longest clean run was around 10). Credit for triggering this
goes to Breno's recent netconsole tests.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/c5a93ed1-9abe-4880-a3bb-8d1678018b1d@redhat.com
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Link: https://patch.msgid.link/20250726010846.1105875-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76be5fae32 ]
We observed an issue from the latest selftest: sockmap_redir where
sk_psock(psock->sk) != psock in the backlog. The root cause is the special
behavior in sockmap_redir - it frequently performs map_update() and
map_delete() on the same socket. During map_update(), we create a new
psock and during map_delete(), we eventually free the psock via rcu_work
in sk_psock_drop(). However, pending workqueues might still exist and not
be processed yet. If users immediately perform another map_update(), a new
psock will be allocated for the same sk, resulting in two psocks pointing
to the same sk.
When the pending workqueue is later triggered, it uses the old psock to
access sk for I/O operations, which is incorrect.
Timing Diagram:
cpu0 cpu1
map_update(sk):
sk->psock = psock1
psock1->sk = sk
map_delete(sk):
rcu_work_free(psock1)
map_update(sk):
sk->psock = psock2
psock2->sk = sk
workqueue:
wakeup with psock1, but the sk of psock1
doesn't belong to psock1
rcu_handler:
clean psock1
free(psock1)
Previously, we used reference counting to address the concurrency issue
between backlog and sock_map_close(). This logic remains necessary as it
prevents the sk from being freed while processing the backlog. But this
patch prevents pending backlogs from using a psock after it has been
stopped.
Note: We cannot call cancel_delayed_work_sync() in map_delete() since this
might be invoked in BPF context by BPF helper, and the function may sleep.
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: Jiayuan Chen <jiayuan.chen@linux.dev>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20250609025908.79331-1-jiayuan.chen@linux.dev
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ead7f9b8de upstream.
In Cilium, we use bpf_csum_diff + bpf_l4_csum_replace to, among other
things, update the L4 checksum after reverse SNATing IPv6 packets. That
use case is however not currently supported and leads to invalid
skb->csum values in some cases. This patch adds support for IPv6 address
changes in bpf_l4_csum_update via a new flag.
When calling bpf_l4_csum_replace in Cilium, it ends up calling
inet_proto_csum_replace_by_diff:
1: void inet_proto_csum_replace_by_diff(__sum16 *sum, struct sk_buff *skb,
2: __wsum diff, bool pseudohdr)
3: {
4: if (skb->ip_summed != CHECKSUM_PARTIAL) {
5: csum_replace_by_diff(sum, diff);
6: if (skb->ip_summed == CHECKSUM_COMPLETE && pseudohdr)
7: skb->csum = ~csum_sub(diff, skb->csum);
8: } else if (pseudohdr) {
9: *sum = ~csum_fold(csum_add(diff, csum_unfold(*sum)));
10: }
11: }
The bug happens when we're in the CHECKSUM_COMPLETE state. We've just
updated one of the IPv6 addresses. The helper now updates the L4 header
checksum on line 5. Next, it updates skb->csum on line 7. It shouldn't.
For an IPv6 packet, the updates of the IPv6 address and of the L4
checksum will cancel each other. The checksums are set such that
computing a checksum over the packet including its checksum will result
in a sum of 0. So the same is true here when we update the L4 checksum
on line 5. We'll update it as to cancel the previous IPv6 address
update. Hence skb->csum should remain untouched in this case.
The same bug doesn't affect IPv4 packets because, in that case, three
fields are updated: the IPv4 address, the IP checksum, and the L4
checksum. The change to the IPv4 address and one of the checksums still
cancel each other in skb->csum, but we're left with one checksum update
and should therefore update skb->csum accordingly. That's exactly what
inet_proto_csum_replace_by_diff does.
This special case for IPv6 L4 checksums is also described atop
inet_proto_csum_replace16, the function we should be using in this case.
This patch introduces a new bpf_l4_csum_replace flag, BPF_F_IPV6,
to indicate that we're updating the L4 checksum of an IPv6 packet. When
the flag is set, inet_proto_csum_replace_by_diff will skip the
skb->csum update.
Fixes: 7d672345ed ("bpf: add generic bpf_csum_diff helper")
Signed-off-by: Paul Chaignon <paul.chaignon@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://patch.msgid.link/96a6bc3a443e6f0b21ff7b7834000e17fb549e05.1748509484.git.paul.chaignon@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paul Chaignon <paul.chaignon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6043b794c7 upstream.
During ILA address translations, the L4 checksums can be handled in
different ways. One of them, adj-transport, consist in parsing the
transport layer and updating any found checksum. This logic relies on
inet_proto_csum_replace_by_diff and produces an incorrect skb->csum when
in state CHECKSUM_COMPLETE.
This bug can be reproduced with a simple ILA to SIR mapping, assuming
packets are received with CHECKSUM_COMPLETE:
$ ip a show dev eth0
14: eth0@if15: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
link/ether 62:ae:35:9e:0f:8d brd ff:ff:ff:ff:ff:ff link-netnsid 0
inet6 3333:0:0:1::c078/64 scope global
valid_lft forever preferred_lft forever
inet6 fd00:10:244:1::c078/128 scope global nodad
valid_lft forever preferred_lft forever
inet6 fe80::60ae:35ff:fe9e:f8d/64 scope link proto kernel_ll
valid_lft forever preferred_lft forever
$ ip ila add loc_match fd00:10:244:1 loc 3333:0:0:1 \
csum-mode adj-transport ident-type luid dev eth0
Then I hit [fd00:10:244:1::c078]:8000 with a server listening only on
[3333:0:0:1::c078]:8000. With the bug, the SYN packet is dropped with
SKB_DROP_REASON_TCP_CSUM after inet_proto_csum_replace_by_diff changed
skb->csum. The translation and drop are visible on pwru [1] traces:
IFACE TUPLE FUNC
eth0:9 [fd00:10:244:3::3d8]:51420->[fd00:10:244:1::c078]:8000(tcp) ipv6_rcv
eth0:9 [fd00:10:244:3::3d8]:51420->[fd00:10:244:1::c078]:8000(tcp) ip6_rcv_core
eth0:9 [fd00:10:244:3::3d8]:51420->[fd00:10:244:1::c078]:8000(tcp) nf_hook_slow
eth0:9 [fd00:10:244:3::3d8]:51420->[fd00:10:244:1::c078]:8000(tcp) inet_proto_csum_replace_by_diff
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) tcp_v6_early_demux
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) ip6_route_input
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) ip6_input
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) ip6_input_finish
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) ip6_protocol_deliver_rcu
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) raw6_local_deliver
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) ipv6_raw_deliver
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) tcp_v6_rcv
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) __skb_checksum_complete
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) kfree_skb_reason(SKB_DROP_REASON_TCP_CSUM)
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) skb_release_head_state
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) skb_release_data
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) skb_free_head
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) kfree_skbmem
This is happening because inet_proto_csum_replace_by_diff is updating
skb->csum when it shouldn't. The L4 checksum is updated such that it
"cancels" the IPv6 address change in terms of checksum computation, so
the impact on skb->csum is null.
Note this would be different for an IPv4 packet since three fields
would be updated: the IPv4 address, the IP checksum, and the L4
checksum. Two would cancel each other and skb->csum would still need
to be updated to take the L4 checksum change into account.
This patch fixes it by passing an ipv6 flag to
inet_proto_csum_replace_by_diff, to skip the skb->csum update if we're
in the IPv6 case. Note the behavior of the only other user of
inet_proto_csum_replace_by_diff, the BPF subsystem, is left as is in
this patch and fixed in the subsequent patch.
With the fix, using the reproduction from above, I can confirm
skb->csum is not touched by inet_proto_csum_replace_by_diff and the TCP
SYN proceeds to the application after the ILA translation.
Link: https://github.com/cilium/pwru [1]
Fixes: 65d7ab8de5 ("net: Identifier Locator Addressing module")
Signed-off-by: Paul Chaignon <paul.chaignon@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://patch.msgid.link/b5539869e3550d46068504feb02d37653d939c0b.1748509484.git.paul.chaignon@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paul Chaignon <paul.chaignon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba9db6f907 upstream.
A not-so-careful NAT46 BPF program can crash the kernel
if it indiscriminately flips ingress packets from v4 to v6:
BUG: kernel NULL pointer dereference, address: 0000000000000000
ip6_rcv_core (net/ipv6/ip6_input.c:190:20)
ipv6_rcv (net/ipv6/ip6_input.c:306:8)
process_backlog (net/core/dev.c:6186:4)
napi_poll (net/core/dev.c:6906:9)
net_rx_action (net/core/dev.c:7028:13)
do_softirq (kernel/softirq.c:462:3)
netif_rx (net/core/dev.c:5326:3)
dev_loopback_xmit (net/core/dev.c:4015:2)
ip_mc_finish_output (net/ipv4/ip_output.c:363:8)
NF_HOOK (./include/linux/netfilter.h:314:9)
ip_mc_output (net/ipv4/ip_output.c:400:5)
dst_output (./include/net/dst.h:459:9)
ip_local_out (net/ipv4/ip_output.c:130:9)
ip_send_skb (net/ipv4/ip_output.c:1496:8)
udp_send_skb (net/ipv4/udp.c:1040:8)
udp_sendmsg (net/ipv4/udp.c:1328:10)
The output interface has a 4->6 program attached at ingress.
We try to loop the multicast skb back to the sending socket.
Ingress BPF runs as part of netif_rx(), pushes a valid v6 hdr
and changes skb->protocol to v6. We enter ip6_rcv_core which
tries to use skb_dst(). But the dst is still an IPv4 one left
after IPv4 mcast output.
Clear the dst in all BPF helpers which change the protocol.
Try to preserve metadata dsts, those may carry non-routing
metadata.
Cc: stable@vger.kernel.org
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Fixes: d219df60a7 ("bpf: Add ipip6 and ip6ip decap support for bpf_skb_adjust_room()")
Fixes: 1b00e0dfe7 ("bpf: update skb->protocol in bpf_skb_net_grow")
Fixes: 6578171a7f ("bpf: add bpf_skb_change_proto helper")
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250610001245.1981782-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8259eb0e06 ]
The sk->sk_socket is not locked or referenced in backlog thread, and
during the call to skb_send_sock(), there is a race condition with
the release of sk_socket. All types of sockets(tcp/udp/unix/vsock)
will be affected.
Race conditions:
'''
CPU0 CPU1
backlog::skb_send_sock
sendmsg_unlocked
sock_sendmsg
sock_sendmsg_nosec
close(fd):
...
ops->release() -> sock_map_close()
sk_socket->ops = NULL
free(socket)
sock->ops->sendmsg
^
panic here
'''
The ref of psock become 0 after sock_map_close() executed.
'''
void sock_map_close()
{
...
if (likely(psock)) {
...
// !! here we remove psock and the ref of psock become 0
sock_map_remove_links(sk, psock)
psock = sk_psock_get(sk);
if (unlikely(!psock))
goto no_psock; <=== Control jumps here via goto
...
cancel_delayed_work_sync(&psock->work); <=== not executed
sk_psock_put(sk, psock);
...
}
'''
Based on the fact that we already wait for the workqueue to finish in
sock_map_close() if psock is held, we simply increase the psock
reference count to avoid race conditions.
With this patch, if the backlog thread is running, sock_map_close() will
wait for the backlog thread to complete and cancel all pending work.
If no backlog running, any pending work that hasn't started by then will
fail when invoked by sk_psock_get(), as the psock reference count have
been zeroed, and sk_psock_drop() will cancel all jobs via
cancel_delayed_work_sync().
In summary, we require synchronization to coordinate the backlog thread
and close() thread.
The panic I catched:
'''
Workqueue: events sk_psock_backlog
RIP: 0010:sock_sendmsg+0x21d/0x440
RAX: 0000000000000000 RBX: ffffc9000521fad8 RCX: 0000000000000001
...
Call Trace:
<TASK>
? die_addr+0x40/0xa0
? exc_general_protection+0x14c/0x230
? asm_exc_general_protection+0x26/0x30
? sock_sendmsg+0x21d/0x440
? sock_sendmsg+0x3e0/0x440
? __pfx_sock_sendmsg+0x10/0x10
__skb_send_sock+0x543/0xb70
sk_psock_backlog+0x247/0xb80
...
'''
Fixes: 4b4647add7 ("sock_map: avoid race between sock_map_close and sk_psock_put")
Reported-by: Michal Luczaj <mhal@rbox.co>
Signed-off-by: Jiayuan Chen <jiayuan.chen@linux.dev>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/r/20250516141713.291150-1-jiayuan.chen@linux.dev
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b4f14b794 ]
In the !ingress path under sk_psock_handle_skb(), when sending data to the
remote under snd_buf limitations, partial skb data might be transmitted.
Although we preserved the partial transmission state (offset/length), the
state wasn't properly consumed during retries. This caused the retry path
to resend the entire skb data instead of continuing from the previous
offset, resulting in data overlap at the receiver side.
Fixes: 405df89dd5 ("bpf, sockmap: Improved check for empty queue")
Signed-off-by: Jiayuan Chen <jiayuan.chen@linux.dev>
Link: https://lore.kernel.org/r/20250407142234.47591-3-jiayuan.chen@linux.dev
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7172dc93d6 upstream.
Commit 1af2dface5 ("af_unix: Don't access successor in unix_del_edges()
during GC.") fixed use-after-free by avoid accessing edge->successor while
GC is in progress.
However, there could be a small race window where another process could
call unix_del_edges() while gc_in_progress is true and __skb_queue_purge()
is on the way.
So, we need another marker for struct scm_fp_list which indicates if the
skb is garbage-collected.
This patch adds dead flag in struct scm_fp_list and set it true before
calling __skb_queue_purge().
Fixes: 1af2dface5 ("af_unix: Don't access successor in unix_del_edges() during GC.")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20240508171150.50601-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29b64e3540 upstream.
As with the previous patch, we preallocate to skb's scm_fp_list an
array of struct unix_edge in the number of inflight AF_UNIX fds.
There we just preallocate memory and do not use immediately because
sendmsg() could fail after this point. The actual use will be in
the next patch.
When we queue skb with inflight edges, we will set the inflight
socket's unix_sock as unix_edge->predecessor and the receiver's
unix_sock as successor, and then we will link the edge to the
inflight socket's unix_vertex.edges.
Note that we set NULL to cloned scm_fp_list.edges in scm_fp_dup()
so that MSG_PEEK does not change the shape of the directed graph.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20240325202425.60930-3-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1fbfdfaa59 upstream.
We will replace the garbage collection algorithm for AF_UNIX, where
we will consider each inflight AF_UNIX socket as a vertex and its file
descriptor as an edge in a directed graph.
This patch introduces a new struct unix_vertex representing a vertex
in the graph and adds its pointer to struct unix_sock.
When we send a fd using the SCM_RIGHTS message, we allocate struct
scm_fp_list to struct scm_cookie in scm_fp_copy(). Then, we bump
each refcount of the inflight fds' struct file and save them in
scm_fp_list.fp.
After that, unix_attach_fds() inexplicably clones scm_fp_list of
scm_cookie and sets it to skb. (We will remove this part after
replacing GC.)
Here, we add a new function call in unix_attach_fds() to preallocate
struct unix_vertex per inflight AF_UNIX fd and link each vertex to
skb's scm_fp_list.vertices.
When sendmsg() succeeds later, if the socket of the inflight fd is
still not inflight yet, we will set the preallocated vertex to struct
unix_sock.vertex and link it to a global list unix_unvisited_vertices
under spin_lock(&unix_gc_lock).
If the socket is already inflight, we free the preallocated vertex.
This is to avoid taking the lock unnecessarily when sendmsg() could
fail later.
In the following patch, we will similarly allocate another struct
per edge, which will finally be linked to the inflight socket's
unix_vertex.edges.
And then, we will count the number of edges as unix_vertex.out_degree.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20240325202425.60930-2-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9f21b3613 upstream.
If more than 16000 inflight AF_UNIX sockets exist and the garbage
collector is not running, unix_(dgram|stream)_sendmsg() call unix_gc().
Also, they wait for unix_gc() to complete.
In unix_gc(), all inflight AF_UNIX sockets are traversed at least once,
and more if they are the GC candidate. Thus, sendmsg() significantly
slows down with too many inflight AF_UNIX sockets.
However, if a process sends data with no AF_UNIX FD, the sendmsg() call
does not need to wait for GC. After this change, only the process that
meets the condition below will be blocked under such a situation.
1) cmsg contains AF_UNIX socket
2) more than 32 AF_UNIX sent by the same user are still inflight
Note that even a sendmsg() call that does not meet the condition but has
AF_UNIX FD will be blocked later in unix_scm_to_skb() by the spinlock,
but we allow that as a bonus for sane users.
The results below are the time spent in unix_dgram_sendmsg() sending 1
byte of data with no FD 4096 times on a host where 32K inflight AF_UNIX
sockets exist.
Without series: the sane sendmsg() needs to wait gc unreasonably.
$ sudo /usr/share/bcc/tools/funclatency -p 11165 unix_dgram_sendmsg
Tracing 1 functions for "unix_dgram_sendmsg"... Hit Ctrl-C to end.
^C
nsecs : count distribution
[...]
524288 -> 1048575 : 0 | |
1048576 -> 2097151 : 3881 |****************************************|
2097152 -> 4194303 : 214 |** |
4194304 -> 8388607 : 1 | |
avg = 1825567 nsecs, total: 7477526027 nsecs, count: 4096
With series: the sane sendmsg() can finish much faster.
$ sudo /usr/share/bcc/tools/funclatency -p 8702 unix_dgram_sendmsg
Tracing 1 functions for "unix_dgram_sendmsg"... Hit Ctrl-C to end.
^C
nsecs : count distribution
[...]
128 -> 255 : 0 | |
256 -> 511 : 4092 |****************************************|
512 -> 1023 : 2 | |
1024 -> 2047 : 0 | |
2048 -> 4095 : 0 | |
4096 -> 8191 : 1 | |
8192 -> 16383 : 1 | |
avg = 410 nsecs, total: 1680510 nsecs, count: 4096
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20240123170856.41348-6-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2b15a0693f ]
Fix mpls maximum labels list parsing up to MAX_MPLS_LABELS entries (instead
of up to MAX_MPLS_LABELS - 1).
Addresses the following:
$ echo "mpls 00000f00,00000f01,00000f02,00000f03,00000f04,00000f05,00000f06,00000f07,00000f08,00000f09,00000f0a,00000f0b,00000f0c,00000f0d,00000f0e,00000f0f" > /proc/net/pktgen/lo\@0
-bash: echo: write error: Argument list too long
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c432722994 ]
When bpf_redirect_peer is used to redirect packets to a device in
another network namespace, the skb isn't scrubbed. That can lead skb
information from one namespace to be "misused" in another namespace.
As one example, this is causing Cilium to drop traffic when using
bpf_redirect_peer to redirect packets that just went through IPsec
decryption to a container namespace. The following pwru trace shows (1)
the packet path from the host's XFRM layer to the container's XFRM
layer where it's dropped and (2) the number of active skb extensions at
each function.
NETNS MARK IFACE TUPLE FUNC
4026533547 d00 eth0 10.244.3.124:35473->10.244.2.158:53 xfrm_rcv_cb
.active_extensions = (__u8)2,
4026533547 d00 eth0 10.244.3.124:35473->10.244.2.158:53 xfrm4_rcv_cb
.active_extensions = (__u8)2,
4026533547 d00 eth0 10.244.3.124:35473->10.244.2.158:53 gro_cells_receive
.active_extensions = (__u8)2,
[...]
4026533547 0 eth0 10.244.3.124:35473->10.244.2.158:53 skb_do_redirect
.active_extensions = (__u8)2,
4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 ip_rcv
.active_extensions = (__u8)2,
4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 ip_rcv_core
.active_extensions = (__u8)2,
[...]
4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 udp_queue_rcv_one_skb
.active_extensions = (__u8)2,
4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 __xfrm_policy_check
.active_extensions = (__u8)2,
4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 __xfrm_decode_session
.active_extensions = (__u8)2,
4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 security_xfrm_decode_session
.active_extensions = (__u8)2,
4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 kfree_skb_reason(SKB_DROP_REASON_XFRM_POLICY)
.active_extensions = (__u8)2,
In this case, there are no XFRM policies in the container's network
namespace so the drop is unexpected. When we decrypt the IPsec packet,
the XFRM state used for decryption is set in the skb extensions. This
information is preserved across the netns switch. When we reach the
XFRM policy check in the container's netns, __xfrm_policy_check drops
the packet with LINUX_MIB_XFRMINNOPOLS because a (container-side) XFRM
policy can't be found that matches the (host-side) XFRM state used for
decryption.
This patch fixes this by scrubbing the packet when using
bpf_redirect_peer, as is done on typical netns switches via veth
devices except skb->mark and skb->tstamp are not zeroed.
Fixes: 9aa1206e8f ("bpf: Add redirect_peer helper")
Signed-off-by: Paul Chaignon <paul.chaignon@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://patch.msgid.link/1728ead5e0fe45e7a6542c36bd4e3ca07a73b7d6.1746460653.git.paul.chaignon@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d25ca2d68 ]
mono_delivery_time was added to check if skb->tstamp has delivery
time in mono clock base (i.e. EDT) otherwise skb->tstamp has
timestamp in ingress and delivery_time at egress.
Renaming the bitfield from mono_delivery_time to tstamp_type is for
extensibilty for other timestamps such as userspace timestamp
(i.e. SO_TXTIME) set via sock opts.
As we are renaming the mono_delivery_time to tstamp_type, it makes
sense to start assigning tstamp_type based on enum defined
in this commit.
Earlier we used bool arg flag to check if the tstamp is mono in
function skb_set_delivery_time, Now the signature of the functions
accepts tstamp_type to distinguish between mono and real time.
Also skb_set_delivery_type_by_clockid is a new function which accepts
clockid to determine the tstamp_type.
In future tstamp_type:1 can be extended to support userspace timestamp
by increasing the bitfield.
Signed-off-by: Abhishek Chauhan <quic_abchauha@quicinc.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://lore.kernel.org/r/20240509211834.3235191-2-quic_abchauha@quicinc.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Stable-dep-of: 3908feb1bd ("Bluetooth: L2CAP: copy RX timestamp to new fragments")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1a4607ffba upstream.
Tail-called programs could execute any of the helpers that invalidate
packet pointers. Hence, conservatively assume that each tail call
invalidates packet pointers.
Making the change in bpf_helper_changes_pkt_data() automatically makes
use of check_cfg() logic that computes 'changes_pkt_data' effect for
global sub-programs, such that the following program could be
rejected:
int tail_call(struct __sk_buff *sk)
{
bpf_tail_call_static(sk, &jmp_table, 0);
return 0;
}
SEC("tc")
int not_safe(struct __sk_buff *sk)
{
int *p = (void *)(long)sk->data;
... make p valid ...
tail_call(sk);
*p = 42; /* this is unsafe */
...
}
The tc_bpf2bpf.c:subprog_tc() needs change: mark it as a function that
can invalidate packet pointers. Otherwise, it can't be freplaced with
tailcall_freplace.c:entry_freplace() that does a tail call.
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20241210041100.1898468-8-eddyz87@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
[ shung-hsi.yu: drop changes to tools/testing/selftests/bpf/progs/tc_bpf2bpf.c
because it is not present. ]
Signed-off-by: Shung-Hsi Yu <shung-hsi.yu@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d4bac0288a ]
Classic BPF socket filters with SKB_NET_OFF and SKB_LL_OFF fail to
read when these offsets extend into frags.
This has been observed with iwlwifi and reproduced with tun with
IFF_NAPI_FRAGS. The below straightforward socket filter on UDP port,
applied to a RAW socket, will silently miss matching packets.
const int offset_proto = offsetof(struct ip6_hdr, ip6_nxt);
const int offset_dport = sizeof(struct ip6_hdr) + offsetof(struct udphdr, dest);
struct sock_filter filter_code[] = {
BPF_STMT(BPF_LD + BPF_B + BPF_ABS, SKF_AD_OFF + SKF_AD_PKTTYPE),
BPF_JUMP(BPF_JMP + BPF_JEQ + BPF_K, PACKET_HOST, 0, 4),
BPF_STMT(BPF_LD + BPF_B + BPF_ABS, SKF_NET_OFF + offset_proto),
BPF_JUMP(BPF_JMP + BPF_JEQ + BPF_K, IPPROTO_UDP, 0, 2),
BPF_STMT(BPF_LD + BPF_H + BPF_ABS, SKF_NET_OFF + offset_dport),
This is unexpected behavior. Socket filter programs should be
consistent regardless of environment. Silent misses are
particularly concerning as hard to detect.
Use skb_copy_bits for offsets outside linear, same as done for
non-SKF_(LL|NET) offsets.
Offset is always positive after subtracting the reference threshold
SKB_(LL|NET)_OFF, so is always >= skb_(mac|network)_offset. The sum of
the two is an offset against skb->data, and may be negative, but it
cannot point before skb->head, as skb_(mac|network)_offset would too.
This appears to go back to when frag support was introduced to
sk_run_filter in linux-2.4.4, before the introduction of git.
The amount of code change and 8/16/32 bit duplication are unfortunate.
But any attempt I made to be smarter saved very few LoC while
complicating the code.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Link: https://lore.kernel.org/netdev/20250122200402.3461154-1-maze@google.com/
Link: https://elixir.bootlin.com/linux/2.4.4/source/net/core/filter.c#L244
Reported-by: Matt Moeller <moeller.matt@gmail.com>
Co-developed-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://lore.kernel.org/r/20250408132833.195491-2-willemdebruijn.kernel@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43130d02ba ]
We noticed the kworker in page_pool_release_retry() was waken
up repeatedly and infinitely in production because of the
buggy driver causing the inflight less than 0 and warning
us in page_pool_inflight()[1].
Since the inflight value goes negative, it means we should
not expect the whole page_pool to get back to work normally.
This patch mitigates the adverse effect by not rescheduling
the kworker when detecting the inflight negative in
page_pool_release_retry().
[1]
[Mon Feb 10 20:36:11 2025] ------------[ cut here ]------------
[Mon Feb 10 20:36:11 2025] Negative(-51446) inflight packet-pages
...
[Mon Feb 10 20:36:11 2025] Call Trace:
[Mon Feb 10 20:36:11 2025] page_pool_release_retry+0x23/0x70
[Mon Feb 10 20:36:11 2025] process_one_work+0x1b1/0x370
[Mon Feb 10 20:36:11 2025] worker_thread+0x37/0x3a0
[Mon Feb 10 20:36:11 2025] kthread+0x11a/0x140
[Mon Feb 10 20:36:11 2025] ? process_one_work+0x370/0x370
[Mon Feb 10 20:36:11 2025] ? __kthread_cancel_work+0x40/0x40
[Mon Feb 10 20:36:11 2025] ret_from_fork+0x35/0x40
[Mon Feb 10 20:36:11 2025] ---[ end trace ebffe800f33e7e34 ]---
Note: before this patch, the above calltrace would flood the
dmesg due to repeated reschedule of release_dw kworker.
Signed-off-by: Jason Xing <kerneljasonxing@gmail.com>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Link: https://patch.msgid.link/20250214064250.85987-1-kerneljasonxing@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Martin KaFai LauandGreg Kroah-Hartman
John SperbeckandGreg Kroah-Hartman
Breno LeitaoandGreg Kroah-Hartman
Eric DumazetandGreg Kroah-Hartman
Paolo AbeniandGreg Kroah-Hartman
Dragos TatuleaandGreg Kroah-Hartman
Jakub KicinskiandGreg Kroah-Hartman
Kuniyuki IwashimaandGreg Kroah-Hartman
Amery HungandGreg Kroah-Hartman
Johannes WiesböckandGreg Kroah-Hartman
Daniel BorkmannandGreg Kroah-Hartman
Paul ChaignonandGreg Kroah-Hartman
Jason BaronandGreg Kroah-Hartman
Kuniyuki IwashimaandGreg Kroah-Hartman
Jakub RamaseuskiandGreg Kroah-Hartman
Nicolas EscandeandGreg Kroah-Hartman
Jiayuan ChenandGreg Kroah-Hartman
Zijun HuandGreg Kroah-Hartman
Peter SeidererandGreg Kroah-Hartman
Abhishek ChauhanandGreg Kroah-Hartman
Eduard ZingermanandGreg Kroah-Hartman
Oleksij RempelandGreg Kroah-Hartman
Justin IurmanandGreg Kroah-Hartman
Willem de BruijnandGreg Kroah-Hartman
Jason XingandGreg Kroah-Hartman