[ Upstream commit d336509cb9 ]
The below commit added optional support for passing a bind address.
It configures the sockaddr bind arguments before parsing options and
reconfigures on options -b and -4.
This broke support for passing port (-p) on its own.
Configure sockaddr after parsing all arguments.
Fixes: 3327a9c463 ("selftests: add functionals test for UDP GRO")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a985442fde ]
Explicitly pass -6 to netcat when the test is using IPv6 to prevent
failures.
Also make sure to pass "-N" to netcat to close the socket after EOF on
the client side, otherwise we would always hit the timeout and the test
would fail.
Without this fix applied:
TEST: GREv6/v4 - copy file w/ TSO [FAIL]
TEST: GREv6/v4 - copy file w/ GSO [FAIL]
TEST: GREv6/v6 - copy file w/ TSO [FAIL]
TEST: GREv6/v6 - copy file w/ GSO [FAIL]
With this fix applied:
TEST: GREv6/v4 - copy file w/ TSO [ OK ]
TEST: GREv6/v4 - copy file w/ GSO [ OK ]
TEST: GREv6/v6 - copy file w/ TSO [ OK ]
TEST: GREv6/v6 - copy file w/ GSO [ OK ]
Fixes: 025efa0a82 ("selftests: add simple GSO GRE test")
Signed-off-by: Andrea Righi <andrea.righi@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17b67370c3 ]
When generating the selftests to another folder, the toeplitz.sh
and toeplitz_client.sh are missing as they are not in Makefile, e.g.
make -C tools/testing/selftests/ install \
TARGETS="net" INSTALL_PATH=/tmp/kselftests
Making them under TEST_PROGS_EXTENDED as they test NIC hardware features
and are not intended to be run from kselftests.
Fixes: 5ebfb4cc30 ("selftests/net: toeplitz test")
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8883deb50e ]
When generating the selftests to another folder, the
vrf_strict_mode_test.sh test will miss as it is not in Makefile, e.g.
make -C tools/testing/selftests/ install \
TARGETS="net" INSTALL_PATH=/tmp/kselftests
Fixes: 8735e6eaa4 ("selftests: add selftest for the VRF strict mode")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 653e7f19b4 ]
When generating the selftests to another folder, the SRv6 tests are
missing as they are not in Makefile, e.g.
make -C tools/testing/selftests/ install \
TARGETS="net" INSTALL_PATH=/tmp/kselftests
Fixes: 03a0b567a0 ("selftests: seg6: add selftest for SRv6 End.DT46 Behavior")
Fixes: 2195444e09 ("selftests: add selftest for the SRv6 End.DT4 behavior")
Fixes: 2bc035538e ("selftests: add selftest for the SRv6 End.DT6 (VRF) behavior")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b99ac18411 ]
When generating the selftests to another folder, the include file
setup_loopback.sh/setup_veth.sh for gro.sh/gre_gro.sh are missing as
they are not in Makefile, e.g.
make -C tools/testing/selftests/ install \
TARGETS="net" INSTALL_PATH=/tmp/kselftests
Fixes: 7d1575014a ("selftests/net: GRO coalesce test")
Fixes: 9af771d2ec ("selftests/net: allow GRO coalesce test on veth")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca3676f94b ]
When generating the selftests to another folder, the icmp.sh test will
miss as it is not in Makefile, e.g.
make -C tools/testing/selftests/ install \
TARGETS="net" INSTALL_PATH=/tmp/kselftests
Fixes: 7e9838b791 ("selftests/net: Add icmp.sh for testing ICMP dummy address responses")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34d7ecb3d4 ]
When I fixed IGMPv3/MLDv2 to use the bridge's multicast_membership_interval
value which is chosen by user-space instead of calculating it based on
multicast_query_interval and multicast_query_response_interval I forgot
to update the selftests relying on that behaviour. Now we have to
manually set the expected GMI value to perform the tests correctly and get
proper results (similar to IGMPv2 behaviour).
Fixes: fac3cb82a5 ("net: bridge: mcast: use multicast_membership_interval for IGMPv3")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b69c99463d ]
The purpose of this test is to verify that after a short activity passes,
the reported time is reasonable: not zero (which could be reported by
mistake), and not something outrageous (which would be indicative of an
issue in used units).
However, the idle time is reported in units of clock_t, or hundredths of
second. If the initial sequence of commands is very quick, it is possible
that the idle time is reported as just flat-out zero. When this test was
recently enabled in our nightly regression, we started seeing spurious
failures for exactly this reason.
Therefore buffer the delay leading up to the test with a sleep, to make
sure there is no legitimate way of reporting 0.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Test that applications binding listening sockets to VRFs without
specifying TCP_MD5SIG_FLAG_IFINDEX will work as expected. This would
be broken if __tcp_md5_do_lookup always made a strict comparison on
l3index. See this email:
https://lore.kernel.org/netdev/209548b5-27d2-2059-f2e9-2148f5a0291b@gmail.com/
Applications using tcp_l3mdev_accept=1 and a single global socket (not
bound to any interface) also should have a way to specify keys that are
only for the default VRF, this is done by --force-bind-key-ifindex
without otherwise binding to a device.
Signed-off-by: Leonard Crestez <cdleonard@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
These options allow explicit control over the TCP_MD5SIG_FLAG_IFINDEX
flag instead of always setting it based on binding to an interface.
Do this by converting to getopt_long because nettest has too many
single-character flags already and getopt_long is widely used in
selftests.
Signed-off-by: Leonard Crestez <cdleonard@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The output behavior for undefined bits is now directly tested inside the bash
script. Trying to set an undefined bit should be refused.
The input behavior for undefined bits has been removed due to the fact that we
would need another sender allowed to set undefined bits.
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Makefile uses TEST_PROGS instead of TEST_GEN_PROGS to define
executables. TEST_PROGS is for shell scripts that need to be
installed and run by the common lib.mk framework. The common
framework doesn't touch TEST_PROGS when it does build and clean.
As a result "make kselftest-clean" and "make clean" fail to remove
executables. Run and install work because the common framework runs
and installs TEST_PROGS. Build works because the Makefile defines
"all" rule which is unnecessary if TEST_GEN_PROGS is used.
Use TEST_GEN_PROGS so the common framework can handle build/run/
install/clean properly.
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the args to fprintf(). Splitting the message ends up passing
incorrect arg for "sigurg %d" and an extra arg overall. The test
result message ends up incorrect.
test_unix_oob.c: In function ‘main’:
test_unix_oob.c:274:43: warning: format ‘%d’ expects argument of type ‘int’, but argument 3 has type ‘char *’ [-Wformat=]
274 | fprintf(stderr, "Test 3 failed, sigurg %d len %d OOB %c ",
| ~^
| |
| int
| %s
275 | "atmark %d\n", signal_recvd, len, oob, atmark);
| ~~~~~~~~~~~~~
| |
| char *
test_unix_oob.c:274:19: warning: too many arguments for format [-Wformat-extra-args]
274 | fprintf(stderr, "Test 3 failed, sigurg %d len %d OOB %c ",
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If altname deletion of the short alternative name fails, the error
message printed is: "Failed to add short alternative name".
This is obviously a typo, as we are testing altname deletion.
Fix this using a proper error message.
Fixes: f95e6c9c46 ("selftest: net: add alternative names test")
Signed-off-by: Andrea Claudi <aclaudi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'$cin' and '$sin' variables are local to a function: they are then not
available from the cleanup trap.
Instead, we need to use '$large' and '$small' that are not local and
defined just before setting the trap.
Without this patch, running this script in a loop might cause a:
write: No space left on device
issue.
Fixes: 1a418cb8e8 ("mptcp: simult flow self-tests")
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This change extends the existing GRO coalesce test to
allow running on top of a veth pair, so that no H/W dep
is required to run them.
By default gro.sh will use the veth backend, and will try
to use exiting H/W in loopback mode if a specific device
name is provided with the '-i' command line option.
No functional change is intended for the loopback-based
tests, just move all the relevant initialization/cleanup
code into the related script.
Introduces a new initialization helper script for the
veth backend, and plugs the correct helper script according
to the provided command line.
Additionally, enable veth-based tests by default.
v1 -> v2:
- drop unused code in setup_veth_ns() - Willem
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several test cases in the net directory are still using
exit 0 or exit 1 when they need to be skipped. Use kselftest
framework skip code instead so it can help us to distinguish the
return status.
Criterion to filter out what should be fixed in net directory:
grep -r "exit [01]" -B1 | grep -i skip
This change might cause some false-positives if people are running
these test scripts directly and only checking their return codes,
which will change from 0 to 4. However I think the impact should be
small as most of our scripts here are already using this skip code.
And there will be no such issue if running them with the kselftest
framework.
Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20210823085854.40216-1-po-hsu.lin@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This silences the following coccinelle warning:
"WARNING: sum of probable bitmasks, consider |"
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: jing yangyang <jing.yangyang@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 09e856d54b ("vrf: Reset skb conntrack connection on VRF rcv")
fixes the "reverse-DNAT" of an SNAT-ed packet over a VRF.
This patch adds a test for this scenario.
Signed-off-by: Lahav Schlesinger <lschlesinger@drivenets.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch dealt with the MPTCP_PM_ADDR_FLAG_FULLMESH flag in add_addr()
and print_addr(), to set and print out the fullmesh flag.
Signed-off-by: Geliang Tang <geliangtang@xiaomi.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As previously discussed with David Ahern, here is a refactored and improved
version of the IOAM self-test. It is now more complete and more robust. Now,
all tests are divided into three categories: OUTPUT (evaluates the IOAM
processing by the sender), INPUT (evaluates the IOAM processing by the receiver)
and GLOBAL (evaluates wider use cases that do not fall into the other two
categories). Both OUTPUT and INPUT tests only use a two-node topology (alpha and
beta), while GLOBAL tests use the entire three-node topology (alpha, beta,
gamma). Each test is documented inside its own handler in the (bash) script.
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add more test-case for link failures scenario,
including recovery from link failure using only
backup subflows and bi-directional transfer.
Additionally explicitly check for stale count
Co-developed-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Build failure in drivers/net/wwan/mhi_wwan_mbim.c:
add missing parameter (0, assuming we don't want buffer pre-alloc).
Conflict in drivers/net/dsa/sja1105/sja1105_main.c between:
589918df93 ("net: dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
0fac6aa098 ("net: dsa: sja1105: delete the best_effort_vlan_filtering mode")
Follow the instructions from the commit message of the former commit
- removed the if conditions. When looking at commit 589918df93 ("net:
dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
note that the mask_iotag fields get removed by the following patch.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To verify that this hash implements the Toeplitz hash function.
Additionally, provide a script toeplitz.sh to run the test in loopback mode
on a networking device of choice (see setup_loopback.sh). Since the
script modifies the NIC setup, it will not be run by selftests
automatically.
Tested:
./toeplitz.sh -i eth0 -irq_prefix <eth0_pattern> -t -6
carrier ready
rxq 0: cpu 14
rxq 1: cpu 20
rxq 2: cpu 17
rxq 3: cpu 23
cpu 14: rx_hash 0x69103ebc [saddr fda8::2 daddr fda8::1 sport 58938 dport 8000] OK rxq 0 (cpu 14)
...
cpu 20: rx_hash 0x257118b9 [saddr fda8::2 daddr fda8::1 sport 59258 dport 8000] OK rxq 1 (cpu 20)
count: pass=111 nohash=0 fail=0
Test Succeeded!
Signed-off-by: Coco Li <lixiaoyan@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a GRO testsuite that expects Linux kernel GRO behavior.
All tests pass with the kernel software GRO stack. Run against a device
with hardware GRO to verify that it matches the software stack.
gro.c generates packets and sends them out through a packet socket. The
receiver in gro.c (run separately) receives the packets on a packet
socket, filters them by destination ports using BPF and checks the
packet geometry to see whether GRO was applied.
gro.sh provides a wrapper to run the gro.c in NIC loopback mode.
It is not included in continuous testing because it modifies network
configuration around a physical NIC: gro.sh sets the NIC in loopback
mode, creates macvlan devices on the physical device in separate
namespaces, and sends traffic generated by gro.c between the two
namespaces to observe coalescing behavior.
GRO coalescing is time sensitive.
Some tests may prove flaky on some hardware.
Note that this test suite tests for software GRO unless hardware GRO is
enabled (ethtool -K $DEV rx-gro-hw on).
To test, run ./gro.sh.
The wrapper will output success or failed test names, and generate
log.txt and stderr.
Sample log.txt result:
...
pure data packet of same size: Test succeeded
large data packets followed by a smaller one: Test succeeded
small data packets followed by a larger one: Test succeeded
...
Sample stderr result:
...
carrier ready
running test ipv4 data
Expected {200 }, Total 1 packets
Received {200 }, Total 1 packets.
...
Signed-off-by: Coco Li <lixiaoyan@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2021-08-04
1) Fix a sysbot reported memory leak in xfrm_user_rcv_msg.
From Pavel Skripkin.
2) Revert "xfrm: policy: Read seqcount outside of rcu-read side
in xfrm_policy_lookup_bytype". This commit tried to fix a
lockin bug, but only cured some of the symptoms. A proper
fix is applied on top of this revert.
3) Fix a locking bug on xfrm state hash resize. A recent change
on sequence counters accidentally repaced a spinlock by a mutex.
Fix from Frederic Weisbecker.
4) Fix possible user-memory-access in xfrm_user_rcv_msg_compat().
From Dmitry Safonov.
5) Add initialiation sefltest fot xfrm_spdattr_type_t.
From Dmitry Safonov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds OOB support for AF_UNIX sockets.
The semantics is same as TCP.
The last byte of a message with the OOB flag is
treated as the OOB byte. The byte is separated into
a skb and a pointer to the skb is stored in unix_sock.
The pointer is used to enforce OOB semantics.
Signed-off-by: Rao Shoaib <rao.shoaib@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removed the 'raw gso min size - 1' test which
always fails now:
./in_netns.sh ./psock_snd -v -c -g -l "${mss}"
raw gso min size - 1 (expected to fail)
tx: 1524
rx: 1472
OK
After commit 7c6d2ecbda ("net: be more gentle about silly
gso requests coming from user"), we relaxed the min gso_size
check in virtio_net_hdr_to_skb().
So when a packet which is smaller then the gso_size,
GSO for this packet will not be set, the packet will be
send/recv successfully.
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The case of ESP in UDP encapsulation was not covered before. Add
cases of local changes of MTU and difference on routed path.
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
This test evaluates the IOAM insertion for IPv6 by checking the IOAM data
integrity on the receiver.
The topology is formed by 3 nodes: Alpha (sender), Beta (router in-between)
and Gamma (receiver). An IOAM domain is configured from Alpha to Gamma only,
which means not on the reverse path. When Gamma is the destination, Alpha
adds an IOAM option (Pre-allocated Trace) inside a Hop-by-hop and fills the
trace with its own IOAM data. Beta and Gamma also fill the trace. The IOAM
data integrity is checked on Gamma, by comparing with the pre-defined IOAM
configuration (see below).
+-------------------+ +-------------------+
| | | |
| alpha netns | | gamma netns |
| | | |
| +-------------+ | | +-------------+ |
| | veth0 | | | | veth0 | |
| | db01::2/64 | | | | db02::2/64 | |
| +-------------+ | | +-------------+ |
| . | | . |
+-------------------+ +-------------------+
. .
. .
. .
+----------------------------------------------------+
| . . |
| +-------------+ +-------------+ |
| | veth0 | | veth1 | |
| | db01::1/64 | ................ | db02::1/64 | |
| +-------------+ +-------------+ |
| |
| beta netns |
| |
+--------------------------+-------------------------+
~~~~~~~~~~~~~~~~~~~~~~
| IOAM configuration |
~~~~~~~~~~~~~~~~~~~~~~
Alpha
+-----------------------------------------------------------+
| Type | Value |
+-----------------------------------------------------------+
| Node ID | 1 |
+-----------------------------------------------------------+
| Node Wide ID | 11111111 |
+-----------------------------------------------------------+
| Ingress ID | 0xffff (default value) |
+-----------------------------------------------------------+
| Ingress Wide ID | 0xffffffff (default value) |
+-----------------------------------------------------------+
| Egress ID | 101 |
+-----------------------------------------------------------+
| Egress Wide ID | 101101 |
+-----------------------------------------------------------+
| Namespace Data | 0xdeadbee0 |
+-----------------------------------------------------------+
| Namespace Wide Data | 0xcafec0caf00dc0de |
+-----------------------------------------------------------+
| Schema ID | 777 |
+-----------------------------------------------------------+
| Schema Data | something that will be 4n-aligned |
+-----------------------------------------------------------+
Note: When Gamma is the destination, Alpha adds an IOAM Pre-allocated Trace
option inside a Hop-by-hop, where 164 bytes are pre-allocated for the
trace, with 123 as the IOAM-Namespace and with 0xfff00200 as the trace
type (= all available options at this time). As a result, and based on
IOAM configurations here, only both Alpha and Beta should be capable of
inserting their IOAM data while Gamma won't have enough space and will
set the overflow bit.
Beta
+-----------------------------------------------------------+
| Type | Value |
+-----------------------------------------------------------+
| Node ID | 2 |
+-----------------------------------------------------------+
| Node Wide ID | 22222222 |
+-----------------------------------------------------------+
| Ingress ID | 201 |
+-----------------------------------------------------------+
| Ingress Wide ID | 201201 |
+-----------------------------------------------------------+
| Egress ID | 202 |
+-----------------------------------------------------------+
| Egress Wide ID | 202202 |
+-----------------------------------------------------------+
| Namespace Data | 0xdeadbee1 |
+-----------------------------------------------------------+
| Namespace Wide Data | 0xcafec0caf11dc0de |
+-----------------------------------------------------------+
| Schema ID | 0xffffff (= None) |
+-----------------------------------------------------------+
| Schema Data | |
+-----------------------------------------------------------+
Gamma
+-----------------------------------------------------------+
| Type | Value |
+-----------------------------------------------------------+
| Node ID | 3 |
+-----------------------------------------------------------+
| Node Wide ID | 33333333 |
+-----------------------------------------------------------+
| Ingress ID | 301 |
+-----------------------------------------------------------+
| Ingress Wide ID | 301301 |
+-----------------------------------------------------------+
| Egress ID | 0xffff (default value) |
+-----------------------------------------------------------+
| Egress Wide ID | 0xffffffff (default value) |
+-----------------------------------------------------------+
| Namespace Data | 0xdeadbee2 |
+-----------------------------------------------------------+
| Namespace Wide Data | 0xcafec0caf22dc0de |
+-----------------------------------------------------------+
| Schema ID | 0xffffff (= None) |
+-----------------------------------------------------------+
| Schema Data | |
+-----------------------------------------------------------+
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set hthresh, dump it again and verify thresh.lbits && thresh.rbits.
They are passed as attributes of xfrm_spdattr_type_t, different from
other message attributes that use xfrm_attr_type_t.
Also, test attribute that is bigger than XFRMA_SPD_MAX, currently it
should be silently ignored.
Cc: Shuah Khan <shuah@kernel.org>
Cc: linux-kselftest@vger.kernel.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Simple functional test for the newly exposed features.
Also add an optional stress test for the channel number
update under flood.
RFC v1 -> RFC v2:
- add the stress test
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from Jakub Kicinski.
"Including fixes from bpf and netfilter.
Current release - regressions:
- sock: fix parameter order in sock_setsockopt()
Current release - new code bugs:
- netfilter: nft_last:
- fix incorrect arithmetic when restoring last used
- honor NFTA_LAST_SET on restoration
Previous releases - regressions:
- udp: properly flush normal packet at GRO time
- sfc: ensure correct number of XDP queues; don't allow enabling the
feature if there isn't sufficient resources to Tx from any CPU
- dsa: sja1105: fix address learning getting disabled on the CPU port
- mptcp: addresses a rmem accounting issue that could keep packets in
subflow receive buffers longer than necessary, delaying MPTCP-level
ACKs
- ip_tunnel: fix mtu calculation for ETHER tunnel devices
- do not reuse skbs allocated from skbuff_fclone_cache in the napi
skb cache, we'd try to return them to the wrong slab cache
- tcp: consistently disable header prediction for mptcp
Previous releases - always broken:
- bpf: fix subprog poke descriptor tracking use-after-free
- ipv6:
- allocate enough headroom in ip6_finish_output2() in case
iptables TEE is used
- tcp: drop silly ICMPv6 packet too big messages to avoid
expensive and pointless lookups (which may serve as a DDOS
vector)
- make sure fwmark is copied in SYNACK packets
- fix 'disable_policy' for forwarded packets (align with IPv4)
- netfilter: conntrack:
- do not renew entry stuck in tcp SYN_SENT state
- do not mark RST in the reply direction coming after SYN packet
for an out-of-sync entry
- mptcp: cleanly handle error conditions with MP_JOIN and syncookies
- mptcp: fix double free when rejecting a join due to port mismatch
- validate lwtstate->data before returning from skb_tunnel_info()
- tcp: call sk_wmem_schedule before sk_mem_charge in zerocopy path
- mt76: mt7921: continue to probe driver when fw already downloaded
- bonding: fix multiple issues with offloading IPsec to (thru?) bond
- stmmac: ptp: fix issues around Qbv support and setting time back
- bcmgenet: always clear wake-up based on energy detection
Misc:
- sctp: move 198 addresses from unusable to private scope
- ptp: support virtual clocks and timestamping
- openvswitch: optimize operation for key comparison"
* tag 'net-5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (158 commits)
net: dsa: properly check for the bridge_leave methods in dsa_switch_bridge_leave()
sfc: add logs explaining XDP_TX/REDIRECT is not available
sfc: ensure correct number of XDP queues
sfc: fix lack of XDP TX queues - error XDP TX failed (-22)
net: fddi: fix UAF in fza_probe
net: dsa: sja1105: fix address learning getting disabled on the CPU port
net: ocelot: fix switchdev objects synced for wrong netdev with LAG offload
net: Use nlmsg_unicast() instead of netlink_unicast()
octeontx2-pf: Fix uninitialized boolean variable pps
ipv6: allocate enough headroom in ip6_finish_output2()
net: hdlc: rename 'mod_init' & 'mod_exit' functions to be module-specific
net: bridge: multicast: fix MRD advertisement router port marking race
net: bridge: multicast: fix PIM hello router port marking race
net: phy: marvell10g: fix differentiation of 88X3310 from 88X3340
dsa: fix for_each_child.cocci warnings
virtio_net: check virtqueue_add_sgs() return value
mptcp: properly account bulk freed memory
selftests: mptcp: fix case multiple subflows limited by server
mptcp: avoid processing packet if a subflow reset
mptcp: fix syncookie process if mptcp can not_accept new subflow
...
After patch "mptcp: fix syncookie process if mptcp can not_accept new
subflow", if subflow is limited, MP_JOIN SYN is dropped, and no SYN/ACK
will be replied.
So in case "multiple subflows limited by server", the expected SYN/ACK
number should be 1.
Fixes: 00587187ad ("selftests: mptcp: add test cases for mptcp join tests with syn cookies")
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Jianguo Wu <wujianguo@chinatelecom.cn>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After redirecting, it's already a new path. So the old PMTU info should
be cleared. The IPv6 test "mtu exception plus redirect" should only
has redirect info without old PMTU.
The IPv4 test can not be changed because of legacy.
Fixes: ec81053528 ("selftests: Add redirect tests")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the kernel doesn't enable option CONFIG_IPV6_SUBTREES, the RTA_SRC
info will not be exported to userspace in rt6_fill_node(). And ip cmd will
not print "from ::" to the route output. So remove this check.
Fixes: ec81053528 ("selftests: Add redirect tests")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull Kselftest update from Shuah Khan:
"Fixes to existing tests and framework:
- migrate sgx test to kselftest harness
- add new test cases to sgx test
- ftrace test fix event-no-pid on 1-core machine
- splice test adjust for handler fallback removal"
* tag 'linux-kselftest-next-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/sgx: remove checks for file execute permissions
selftests/ftrace: fix event-no-pid on 1-core machine
selftests/sgx: Refine the test enclave to have storage
selftests/sgx: Add EXPECT_EEXIT() macro
selftests/sgx: Dump enclave memory map
selftests/sgx: Migrate to kselftest harness
selftests/sgx: Rename 'eenter' and 'sgx_call_vdso'
selftests: timers: rtcpie: skip test if default RTC device does not exist
selftests: lib.mk: Also install "config" and "settings"
selftests: splice: Adjust for handler fallback removal
selftests/tls: Add {} to avoid static checker warning
selftests/resctrl: Fix incorrect parsing of option "-t"
