Pull phy updates from Vinod Koul:
"Bunch of new driver, device support in existing drivers/binding and
few updates to existing drivers
New Support:
- Qualcomm Eliza QMP PHY, Eliza Synopsys eUSB2 support, Eliza PCIe
phy support, Nord QMP UFS PHY, IPQ5210 USB3 PHY support
- Econet EN751221 and EN7528 PCIe phy support
- NXPs TJA1145 CAN transceiver phy support
- TI DS125DF111 retimer phy support
- Rockchip RK3528 usb phy support
- TI J722S phy support
- Axiado eMMC PHY driver
- EyeQ5 Ethernet PHY driver
- Generic PHY driver for Lynx 10G SerDes
- Spacemit K3 USB2 PHY support
Updates:
- Tomi helping maintian zynqmp phys
- lynx phy updates to support 25GBASER
- Rockchip GRF for RK3568/RV1108 support
- Qualcomm QSERDES COM v2 support"
* tag 'phy-for-7.2' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (87 commits)
phy: rockchip: inno-usb2: Add missing clkout_ctl_phy kerneldoc
phy: Move MODULE_DEVICE_TABLE next to the table itself
phy: add basic support for NXPs TJA1145 CAN transceiver
dt-bindings: phy: add support for NXPs TJA1145 CAN transceiver
phy: freescale: phy-fsl-imx8qm-lvds-phy: Fix missing pm_runtime_disable() on probe error path
dt-bindings: phy: qcom,qmp-usb: Add ipq5210 USB3 PHY
dt-bindings: phy: qcom,qusb2: Document IPQ5210 compatible
phy: freescale: phy-fsl-imx8qm-lvds-phy: Use synchronous PM runtime put in reset
MAINTAINERS: expand Lynx 28G entry to cover Lynx 10G SerDes
phy: lynx-10g: new driver
dt-bindings: phy: lynx-10g: initial document
phy: lynx-28g: improve phy_validate() procedure
phy: lynx-28g: optimize read-modify-write operation
phy: lynx-28g: add support for big endian register maps
phy: lynx-28g: common probe() and remove()
phy: lynx-28g: make lynx_28g_pll_read_configuration() callable per PLL
phy: lynx-28g: move struct lynx_info definitions downwards
phy: lynx-28g: provide default lynx_lane_supports_mode() implementation
phy: lynx-28g: generalize protocol converter accessors
phy: lynx-28g: common lynx_pll_get()
...
Keep the USB pipe clock working when the phy is in DP-only mode, because
the dwc controller still needs it for USB 2.0 over the same Type-C port.
Tested with the BenQ RD280UA monitor which has a downstream-facing port
for data passthrough that's manually switchable between USB 2 and 3,
corresponding to 4-lane and 2-lane DP respectively.
Note: the suspend/resume callbacks were already gating the enable/disable
of this clock only on init_count and not usb_init_count!
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Val Packett <val@packett.cool>
Link: https://patch.msgid.link/20260304190827.176988-1-val@packett.cool
Signed-off-by: Vinod Koul <vkoul@kernel.org>
A repeater is not required for the PHY to function. On systems with
multiple PHY instances connected to a multi-port controller, some PHYs
may be unconnected. All PHYs must still probe successfully even without
attached repeaters, otherwise the controller probe fails.
So make it optional.
Signed-off-by: Wesley Cheng <wesley.cheng@oss.qualcomm.com>
[abel.vesa@oss.qualcomm.com: commit re-worded to reflect actual reason]
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://patch.msgid.link/20260302-phy-qcom-m31-eusb2-make-repeater-optional-v2-1-dbf714c72056@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit 81af9e40e2 ("phy: qcom: qmp-ufs: Fix SM8650 PCS table for Gear 4")
moved QPHY_V6_PCS_UFS_PLL_CNTL register configuration from the shared
sm8650_ufsphy_g5_pcs table to the SM8650-specific sm8650_ufsphy_pcs base
table to fix Gear 4 operation on SM8650.
However, this change inadvertently broke kaanapali and SM8750 SoCs
which also rely on the shared sm8650_ufsphy_g5_pcs table for Gear 5
configuration but use their own sm8750_ufsphy_pcs base table. After the
change, kaanapali PHYs are left without the required PLL_CNTL = 0x33
setting, causing the PHY PLL to remain at its hardware reset default
value, preventing PLL lock and resulting in DME_LINKSTARTUP timeouts.
Fix this by adding the missing QPHY_V6_PCS_UFS_PLL_CNTL = 0x33 entry
to the sm8750_ufsphy_pcs table, mirroring what the original commit
already did for sm8650_ufsphy_pcs.
Cc: stable@vger.kernel.org # v6.19.12
Fixes: 81af9e40e2 ("phy: qcom: qmp-ufs: Fix SM8650 PCS table for Gear 4")
Signed-off-by: Nitin Rawat <nitin.rawat@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20260415104851.2763238-1-nitin.rawat@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit 81791c45c8 ("phy: qcom: qmp-usbc: Add QCS615 USB/DP PHY config
and DP mode support") chose to name QCS615 DP PHY variables/functions
with qmp_v2 prefix, by assuming that QMP PHY registers are versioned
as a whole. However, the reality is that the registers are versioned
in sub-modules like QSERDES COM and QSERDES TXRX respectively, e.g.
QCS615 DP PHY has registers of QSERDES COM v2 and QSERDES TXRX v3.
Thus it may cause confusion that qmp_v2_xxx table and functions access
QSERDES TXRX v3 registers.
Rename QCS615 DP PHY variables and functions to be prefixed by qcs615
instead of qmp_v2. This better aligns with how the driver names USB3 PHY
variables for QCM2290 etc.
Signed-off-by: Shawn Guo <shengchao.guo@oss.qualcomm.com>
Link: https://patch.msgid.link/20260314051325.198137-5-shengchao.guo@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The eDP PHY supports both eDP/DP modes, each requiring a different
swing/pre-emphasis table. However, the driver currently uses a fixed
static table for eDP programming rather than selecting the appropriate
table based on the current mode. Add separate tables for eDP and DP
modes, and select the appropriate table dynamically based on the
current mode.
Glymur's DP mode table differs from the other platforms, add a
dedicated table for it.
This also fixes the table mismatch for X1E80100 (eDP) and SA8775P (DP).
Cc: stable@vger.kernel.org
Fixes: 3f12bf1621 ("phy: qcom: edp: Add support for eDP PHY on SA8775P")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Yongxing Mou <yongxing.mou@oss.qualcomm.com>
Link: https://patch.msgid.link/20260427-edp_phy-v5-2-3bb876824475@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pull phy updates from Vinod Koul:
"New Support:
- Qualcomm Eliza QMP UFS PHY
- Canaan K230 USB 2.0 PHY driver
- Mediatek mt8167 dsi-phy
- Eswin EIC7700 SATA PHY driver
Updates:
- Sorted subsytem Makefile/Kconfig and some kernel-doc udpates"
* tag 'phy-for-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy:
dt-bindings: phy: qcom,sc8280xp-qmp-ufs-phy: document the Eliza QMP UFS PHY
phy: qcom: m31-eusb2: clear PLL_EN during init
phy: eswin: Create eswin directory and add EIC7700 SATA PHY driver
dt-bindings: phy: eswin: Document the EIC7700 SoC SATA PHY
phy: apple: apple: Use local variable for ioremap return value
phy: qcom: qmp-usbc: Simplify check for non-NULL pointer
phy: marvell: mmp3-hsic: Avoid re-casting __iomem
phy: apple: atc: Make atcphy_dwc3_reset_ops variable static
dt-bindings: phy: mediatek,dsi-phy: Add support for mt8167
phy: usb: Add driver for Canaan K230 USB 2.0 PHY
dt-bindings: phy: Add Canaan K230 USB PHY
phy: phy-mtk-tphy: Update names and format of kernel-doc comments
phy: Sort the subsystem Kconfig
phy: Sort the subsystem Makefile
phy: move spacemit pcie driver to its subfolder
As established in the previous commit, using SPEED_1000 and SPEED_2500
does not make sense for a SerDes due to the PCS encoding that is used
over the SerDes link, which inflates the data rate at the SerDes. Thus,
the use of these constants in a SerDes driver is incorrect.
Since qcom-sgmii-eth no longer implements phy_set_speed(), but instead
uses the PHY interface mode passed via the .set_mode() method, convert
the driver to use the PHY interface mode internally to decide whether
to configure the SerDes for 1.25Gbps or 3.125Gbps mode.
Tested-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vxS4E-0000000BQXg-46dJ@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that the qcom-ethqos driver has migrated to use phy_set_mode_ext()
rather than phy_set_speed() to configure the SerDes, the support for
phy_set_speed() is now obsolete. Remove support for this method.
Using the MAC speed for the SerDes is never correct due to the PCS
encoding. For SGMII and 2500BASE-X, the PCS uses 8B10B encoding, and
so:
MAC rate * PCS output bits / PCS input bits = SerDes rate
1000M * 10 / 8 = 1250M
2500M * 10 / 8 = 3125M
Tested-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vxS49-0000000BQXa-3Zcg@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
qcom-sgmii-eth is an Ethernet SerDes supporting only Ethernet mode
using SGMII, 1000BASE-X and 2500BASE-X.
Add an implementation of the .set_mode() method, which can be used
instead of or as well as the .set_speed() method. The Ethernet
interface modes mentioned above all have a fixed data rate, so
setting the mode is sufficient to fully specify the operating
parameters.
Add an implementation of the .validate() method, which will be
necessary to allow discovery of the SerDes capabilities for platform
independent SerDes support in the stmmac network driver.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vvkU3-0000000AuP2-0hu3@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver currently sets bit 0 of USB_PHY_CFG1 (PLL_EN) during PHY
initialization. According to the M31 EUSB2 PHY hardware documentation,
this bit is intended only for test/debug scenarios and does not control
mission mode operation. Keeping PLL_EN asserted causes the PHY to draw
additional current during USB bus suspend. Clearing this bit results in
lower suspend power consumption without affecting normal operation.
Update the driver to leave PLL_EN cleared as recommended by the hardware
documentation.
Fixes: 9c8504861c ("phy: qcom: Add M31 based eUSB2 PHY driver")
Cc: stable@vger.kernel.org
Signed-off-by: Elson Serrao <elson.serrao@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://patch.msgid.link/20260217201130.2804550-1-elson.serrao@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
On X Elite, the DP PHY needs another clock called ref, while all other
platforms do not.
The current X Elite devices supported upstream work fine without this
clock, because the boot firmware leaves this clock enabled. But we should
not rely on that. Also, even though this change breaks the ABI, it is
needed in order to make the driver disables this clock along with the
other ones, for a proper bring-down of the entire PHY.
So in order to handle these clocks on different platforms, make the driver
get all the clocks regardless of how many there are provided.
Cc: stable@vger.kernel.org # v6.10
Fixes: db83c107dc ("phy: qcom: edp: Add v6 specific ops and X1E80100 platform support")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://patch.msgid.link/20251224-phy-qcom-edp-add-missing-refclk-v5-2-3f45d349b5ac@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Starting with Glymur, the PCIe and DP PHYs qserdes register offsets differ
for the same version number. So in order to be able to differentiate
between them, add these ones with DP prefix.
Add the necessary PHY setting tables for enabling the DP path within the
QMP subsystem. Introduced some new callbacks for v8 specific sequences,
such as for clock configurations based on the different link speeds.
Wesley Cheng added some updated settings from the hardware programming
guides on existing PHY tables and clock settings.
Co-developed-by: Wesley Cheng <wesley.cheng@oss.qualcomm.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Wesley Cheng <wesley.cheng@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20251209-linux-next-12825-v8-9-42133596bda0@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For SuperSpeed USB to work properly, there is a set of HW settings that
need to be programmed into the USB blocks within the QMP PHY. Ensure that
these settings follow the latest settings mentioned in the HW programming
guide. The QMP USB PHY on Glymur is a USB43 based PHY that will have some
new ways to define certain registers, such as the replacement of TXA/RXA
and TXB/RXB register sets. This was replaced with the LALB register set.
There are also some PHY init updates to modify the PCS MISC register space.
Without these, the QMP PHY PLL locking fails.
Signed-off-by: Wesley Cheng <wesley.cheng@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20251209-linux-next-12825-v8-8-42133596bda0@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Uwe Kleine-König (The Capable Hub)
Linus Torvalds
Krishna Chaitanya Chundru
Xiangxu Yin
Val Packett
Rosen Penev
Wesley Cheng
Nitin Rawat
Shawn Guo
Yongxing Mou
Jakub Kicinski
Russell King (Oracle)
Abel Vesa
Elson Serrao
Krzysztof Kozlowski
Krishna Kurapati
Luca Weiss
Abel Vesa
Abel Vesa