[ Upstream commit c3966ced8e ]
Smatch reports the following error:
drivers/phy/qualcomm/phy-qcom-usb-hsic.c:82 qcom_usb_hsic_phy_power_on()
warn: 'uphy->cal_clk' from clk_prepare_enable() not released on lines:
58.
drivers/phy/qualcomm/phy-qcom-usb-hsic.c:82 qcom_usb_hsic_phy_power_on()
warn: 'uphy->cal_sleep_clk' from clk_prepare_enable() not released on
lines: 58.
drivers/phy/qualcomm/phy-qcom-usb-hsic.c:82 qcom_usb_hsic_phy_power_on()
warn: 'uphy->phy_clk' from clk_prepare_enable() not released on lines:
58.
Fix this by calling proper clk_disable_unprepare calls.
Fixes: 0b56e9a7e8 ("phy: Group vendor specific phy drivers")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20220914051334.69282-1-dzm91@hust.edu.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d644e0d798 ]
The pm_runtime_enable will increase power disable depth.
If the probe fails, we should use pm_runtime_disable() to balance
pm_runtime_enable(). And use pm_runtime_dont_use_autosuspend() to
undo pm_runtime_use_autosuspend()
In the PM Runtime docs:
Drivers in ->remove() callback should undo the runtime PM changes done
in ->probe(). Usually this means calling pm_runtime_disable(),
pm_runtime_dont_use_autosuspend() etc.
We should do this in error handling.
Fixes: f7f50b2a7b ("phy: mapphone-mdm6600: Add runtime PM support for n_gsm on USB suspend")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220301024615.31899-1-linmq006@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3153fa38e3 ]
According to the comment of the function phy_mipi_dphy_get_default_config(),
it uses minimum D-PHY timings based on MIPI D-PHY specification. They are
derived from the valid ranges specified in Section 6.9, Table 14, Page 41
of the D-PHY specification (v1.2). The table 14 explicitly mentions that
the minimum T-LPX parameter is 50 nanoseconds and the minimum TA-SURE
parameter is T-LPX nanoseconds. Likewise, the kernel doc of the 'lpx' and
'ta_sure' members of struct phy_configure_opts_mipi_dphy mentions that
the minimum values are 50000 picoseconds and @lpx picoseconds respectively.
Also, the function phy_mipi_dphy_config_validate() checks if cfg->lpx is
less than 50000 picoseconds and if cfg->ta_sure is less than cfg->lpx,
which hints the same minimum values.
Without this patch, the function phy_mipi_dphy_get_default_config()
wrongly sets cfg->lpx to 60000 picoseconds and cfg->ta_sure to 2 * cfg->lpx.
So, let's correct them to 50000 picoseconds and cfg->lpx respectively.
Note that I've only tested the patch with RM67191 DSI panel on i.MX8mq EVK.
Help is needed to test with other i.MX8mq, Meson and Rockchip platforms,
as I don't have the hardwares.
Fixes: dddc97e823 ("phy: dphy: Add configuration helpers")
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Link: https://lore.kernel.org/r/20220216071257.1647703-1-victor.liu@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42fed57046 ]
The PHY client driver does a phy_exit() call on suspend or rmmod and
the PHY driver needs to know the difference because some clocks need
to be kept running for suspend but can be shutdown on unbind/rmmod
(or if there are no PHY clients at all).
The fix is to use a PM notifier so the driver can tell if a PHY
client is calling exit() because of a system suspend or a driver
unbind/rmmod.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211201180653.35097-2-alcooperx@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37291f60d0 ]
TX_PROT_BUS_WIDTH and RX_PROT_BUS_WIDTH are single registers with
separate bit fields for each lane. The code in xpsgtr_phy_init_sgmii was
not preserving the existing register value for other lanes, so enabling
the PHY in SGMII mode on one lane zeroed out the settings for all other
lanes, causing other PS-GTR peripherals such as USB3 to malfunction.
Use xpsgtr_clr_set to only manipulate the desired bits in the register.
Fixes: 4a33bea003 ("phy: zynqmp: Add PHY driver for the Xilinx ZynqMP Gigabit Transceiver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20220126001600.1592218-1-robert.hancock@calian.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b475bf0ec4 ]
The FSEL_MASK which selects the refclock is defined incorrectly.
It should be [4:6] not [5:7]. Due to this incorrect definition, the BIT(7)
in USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON0 is reset which keeps PHY analog
blocks ON during suspend.
Fix this issue by correctly defining the FSEL_MASK.
Fixes: 51e8114f80 ("phy: qcom-snps: Add SNPS USB PHY driver for QCOM based SOCs")
Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Link: https://lore.kernel.org/r/1635135575-5668-1-git-send-email-quic_c_sanm@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a90bbb478 ]
The current driver uses a value from register TEST_O as the original
value for register TEST_I, though, the value is overwritten by "param",
so there is a bug that the original value isn't no longer used.
The value of TEST_O[7:0] should be masked with "mask", replaced with
"param", and placed in the bitfield TESTI_DAT_MASK as new TEST_I value.
Fixes: c6d9b13241 ("phy: socionext: add PCIe PHY driver support")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1623037842-19363-1-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e52a39f19 ]
commit 091876cc35 ("phy: ti: j721e-wiz: Add support for WIZ module
present in TI J721E SoC") modeled both MUX clocks and DIVIDER clocks in
wiz. However during cleanup, it removed only the MUX clock provider.
Remove the DIVIDER clock provider here.
Fixes: 091876cc35 ("phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210310120840.16447-3-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f7eb147d30 upstream.
Invoke wiz_init() before configuring anything else in Sierra/Torrent
(invoked as part of of_platform_device_create()). wiz_init() resets the
SERDES device and any configuration done in the probe() of
Sierra/Torrent will be lost. In order to prevent SERDES configuration
from getting reset, invoke wiz_init() immediately before invoking
of_platform_device_create().
Fixes: 091876cc35 ("phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Swapnil Jakhade <sjakhade@cadence.com>
Cc: <stable@vger.kernel.org> # v5.10
Link: https://lore.kernel.org/r/20210319124128.13308-3-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e1723d8b87 ]
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210407092716.3270248-1-yangyingliang@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 764257d906 ]
On deferred probe, we will get the following splat:
cpcap-usb-phy cpcap-usb-phy.0: could not initialize VBUS or ID IIO: -517
WARNING: CPU: 0 PID: 21 at drivers/regulator/core.c:2123 regulator_put+0x68/0x78
...
(regulator_put) from [<c068ebf0>] (release_nodes+0x1b4/0x1fc)
(release_nodes) from [<c068a9a4>] (really_probe+0x104/0x4a0)
(really_probe) from [<c068b034>] (driver_probe_device+0x58/0xb4)
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20201230102105.11826-1-tony@atomide.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b097efba95 ]
Currently there is a null pointer check for hdmi_phy that implies it
may be null, however a dev_err messages dereferences this potential null
pointer. Avoid a null pointer dereference by only emitting the dev_err
message if hdmi_phy is non-null. It is a moot point if the error message
needs to be printed at all, but since this is a relatively new piece of
code it may be useful to keep the message in for the moment in case there
are unforseen errors that need to be reported.
Fixes: be28b6507c ("drm/mediatek: separate hdmi phy to different file")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Dereference after null check")
Link: https://lore.kernel.org/r/20201207150937.170435-1-colin.king@canonical.com
[vkoul: fix indent of return call]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5f6e01f91 ]
Compile-testing the DRM_MEDIATEK_HDMI driver shows two missing
dependencies, one results in a link failure:
arm-linux-gnueabi-ld: drivers/phy/mediatek/phy-mtk-hdmi.o: in function `mtk_hdmi_phy_probe':
phy-mtk-hdmi.c:(.text+0xd8): undefined reference to `__clk_get_name'
arm-linux-gnueabi-ld: phy-mtk-hdmi.c:(.text+0x12c): undefined reference to `devm_clk_register'
arm-linux-gnueabi-ld: phy-mtk-hdmi.c:(.text+0x250): undefined reference to `of_clk_add_provider'
arm-linux-gnueabi-ld: phy-mtk-hdmi.c:(.text+0x298): undefined reference to `of_clk_src_simple_get'
The other one is a harmless warning:
WARNING: unmet direct dependencies detected for PHY_MTK_HDMI
Depends on [n]: ARCH_MEDIATEK [=n] && OF [=y]
Selected by [y]:
- DRM_MEDIATEK_HDMI [=y] && HAS_IOMEM [=y] && DRM_MEDIATEK [=y]
Fix these by adding dependencies on CONFIG_OF and CONFIG_COMMON_CLK.
With that done, there is also no reason against adding
CONFIG_COMPILE_TEST.
Fixes: b28be59a2e ("phy: mediatek: Move mtk_hdmi_phy driver into drivers/phy/mediatek folder")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201204135650.2744481-1-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Alain Volmat
Gaosheng Cui
Jiapeng Chong
Shang XiaoJing
Randy Dunlap
Al Cooper
Dan Carpenter
Dongliang Mu
Johan Hovold
Miaoqian Lin
Krzysztof Kozlowski
Amjad Ouled-Ameur
Liu Ying
Kishon Vijay Abraham I
Robert Hancock
Ryuta NAKANISHI
Sandeep Maheswaram
Vladimir Zapolskiy
Rashmi A
Christophe JAILLET
Kunihiko Hayashi
Tiezhu Yang
Yang Li
Wang Wensheng
Chen Li
Geert Uytterhoeven
Yang Yingliang
Mathias Kresin
Chris Ruehl
Tony Lindgren
Colin Ian King
Wang Li
Arnd Bergmann
JC Kuo
Bryan O'Donoghue