[ Upstream commit 2c27aaee93 ]
Do read-modify-write so that we re-use the characterized reset value as
specified in TRM [1] to program calibration wait time which defines number
of cycles to wait for after startup state machine is in bandgap enable
state.
This fixes PLL lock timeout error faced while using RPi DSI Panel on TI's
AM62L and J721E SoC since earlier calibration wait time was getting
overwritten to zero value thus failing the PLL to lockup and causing
timeout.
[1] AM62P TRM (Section 14.8.6.3.2.1.1 DPHY_TX_DPHYTX_CMN0_CMN_DIG_TBIT2):
Link: https://www.ti.com/lit/pdf/spruj83
Cc: stable@vger.kernel.org
Fixes: 7a343c8bf4 ("phy: Add Cadence D-PHY support")
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Tested-by: Harikrishna Shenoy <h-shenoy@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://lore.kernel.org/r/20250704125915.1224738-3-devarsht@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 284fb19a3f ]
PLL lockup and O_CMN_READY assertion can only happen after common state
machine gets enabled by programming DPHY_CMN_SSM register, but driver was
polling them before the common state machine was enabled which is
incorrect. This is as per the DPHY initialization sequence as mentioned in
J721E TRM [1] at section "12.7.2.4.1.2.1 Start-up Sequence Timing Diagram".
It shows O_CMN_READY polling at the end after common configuration pin
setup where the common configuration pin setup step enables state machine
as referenced in "Table 12-1533. Common Configuration-Related Setup
mentions state machine"
To fix this :
- Add new function callbacks for polling on PLL lock and O_CMN_READY
assertion.
- As state machine and clocks get enabled in power_on callback only, move
the clock related programming part from configure callback to power_on
callback and poll for the PLL lockup and O_CMN_READY assertion after state
machine gets enabled.
- The configure callback only saves the PLL configuration received from the
client driver which will be applied later on in power_on callback.
- Add checks to ensure configure is called before power_on and state
machine is in disabled state before power_on callback is called.
- Disable state machine in power_off so that client driver can re-configure
the PLL by following up a power_off, configure, power_on sequence.
[1]: https://www.ti.com/lit/zip/spruil1
Cc: stable@vger.kernel.org
Fixes: 7a343c8bf4 ("phy: Add Cadence D-PHY support")
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Tested-by: Harikrishna Shenoy <h-shenoy@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://lore.kernel.org/r/20250704125915.1224738-2-devarsht@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7bb14b61b7 ]
The boot firmware may disable the U3 port early during boot and leave it
up to the controller or PHY driver to re-enable U3 when needed.
The Rockchip USBDP PHY driver currently does this for RK3576 and RK3588,
something the Rockchip Naneng Combo PHY driver never does for RK3568.
This may result in USB 3.0 ports being limited to only using USB 2.0 or
in special cases not working at all on RK3568.
Write to PIPE_GRF USB3OTGx_CON1 reg to ensure the U3 port is enabled
when a PHY with PHY_TYPE_USB3 mode is used.
Fixes: 7160820d74 ("phy: rockchip: add naneng combo phy for RK3568")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20250723072324.2246498-1-jonas@kwiboo.se
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 24c63c590a upstream.
The logic that drives the pad calibration values resides in the
controller reset domain and so the calibration values are only being
captured when the controller is out of reset. However, by clearing the
CYA_TRK_CODE_UPDATE_ON_IDLE bit, the calibration values can be set
while the controller is in reset.
The CYA_TRK_CODE_UPDATE_ON_IDLE bit was previously cleared based on the
trk_hw_mode flag, but this dependency is not necessary. Instead,
introduce a new flag, trk_update_on_idle, to independently control this
bit.
Fixes: d8163a32ca ("phy: tegra: xusb: Add Tegra234 support")
Cc: stable@vger.kernel.org
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20250519090929.3132456-2-waynec@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cefc1caee9 upstream.
When transitioning from USB_ROLE_DEVICE to USB_ROLE_NONE, the code
assumed that the regulator should be disabled. However, if the regulator
is marked as always-on, regulator_is_enabled() continues to return true,
leading to an incorrect attempt to disable a regulator which is not
enabled.
This can result in warnings such as:
[ 250.155624] WARNING: CPU: 1 PID: 7326 at drivers/regulator/core.c:3004
_regulator_disable+0xe4/0x1a0
[ 250.155652] unbalanced disables for VIN_SYS_5V0
To fix this, we move the regulator control logic into
tegra186_xusb_padctl_id_override() function since it's directly related
to the ID override state. The regulator is now only disabled when the role
transitions from USB_ROLE_HOST to USB_ROLE_NONE, by checking the VBUS_ID
register. This ensures that regulator enable/disable operations are
properly balanced and only occur when actually transitioning to/from host
mode.
Fixes: 49d46e3c7e ("phy: tegra: xusb: Add set_mode support for UTMI phy on Tegra186")
Cc: stable@vger.kernel.org
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20250502092606.2275682-1-waynec@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b15ee09ddb upstream.
The description of TX_VBOOST_LVL is wrong in register PHY_CTRL3
bit[31:29].
The updated description as below:
011: Corresponds to a launch amplitude of 0.844 V.
100: Corresponds to a launch amplitude of 1.008 V.
101: Corresponds to a launch amplitude of 1.156 V.
This will fix the parsing function
phy_tx_vboost_level_from_property() to return correct value.
Fixes: 63c85ad0cd ("phy: fsl-imx8mp-usb: add support for phy tuning")
Cc: stable@vger.kernel.org
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20250430094502.2723983-3-xu.yang_2@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d14402a38c ]
The qmp_usb_iomap() helper function currently returns the raw result of
devm_ioremap() for non-exclusive mappings. Since devm_ioremap() may return
a NULL pointer and the caller only checks error pointers with IS_ERR(),
NULL could bypass the check and lead to an invalid dereference.
Fix the issue by checking if devm_ioremap() returns NULL. When it does,
qmp_usb_iomap() now returns an error pointer via IOMEM_ERR_PTR(-ENOMEM),
ensuring safe and consistent error handling.
Signed-off-by: Chenyuan Yang <chenyuan0y@gmail.com>
Fixes: a5d6b1ac56 ("phy: qcom-qmp-usb: fix memleak on probe deferral")
CC: Johan Hovold <johan@kernel.org>
CC: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250414125050.2118619-1-chenyuan0y@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9475055b1 ]
When using HDMI PLL frequency division coefficient at 50.25MHz
that is calculated by rk_hdptx_phy_clk_pll_calc(), it fails to
get PHY LANE lock. Although the calculated values are within the
allowable range of PHY PLL configuration.
In order to fix the PHY LANE lock error and provide the expected
50.25MHz output, manually compute the required PHY PLL frequency
division coefficient and add it to ropll_tmds_cfg configuration
table.
Signed-off-by: Algea Cao <algea.cao@rock-chips.com>
Reviewed-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250427095124.3354439-1-algea.cao@rock-chips.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21860f340b ]
This code's intention is to configure lane0 and lane2 tunings, but for
lane2 there is a typo and it ends up tuning something else.
Fix the typo, as it doesn't appear to make sense to apply different
tunings for lane0 vs lane2.
The same typo appears to exist in the bootloader, hence we restore the
original value in the typo'd registers as well. This can be removed
once / if the bootloader is updated.
Note that this is incorrect in the downstream driver as well - the
values had been copied from there.
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Link: https://lore.kernel.org/r/20241206-gs101-phy-lanes-orientation-phy-v4-4-f5961268b149@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 969a38be43 ]
According documentation of phy_configure_opts_dp, at the configure
stage, link rates should only be verify/configure when set_rate
flag is set, the same applies to lanes and voltage.
So do it as the documentation says.
Because voltage setting depends on the lanes, link rates set
previously, so record the link rates and lanes at it's verify stage.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Link: https://lore.kernel.org/r/20250312080041.524546-1-andyshrk@163.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55a387ebb9 ]
The phy-rcar-gen3-usb2 driver exposes four individual PHYs that are
requested and configured by PHY users. The struct phy_ops APIs access the
same set of registers to configure all PHYs. Additionally, PHY settings can
be modified through sysfs or an IRQ handler. While some struct phy_ops APIs
are protected by a driver-wide mutex, others rely on individual
PHY-specific mutexes.
This approach can lead to various issues, including:
1/ the IRQ handler may interrupt PHY settings in progress, racing with
hardware configuration protected by a mutex lock
2/ due to msleep(20) in rcar_gen3_init_otg(), while a configuration thread
suspends to wait for the delay, another thread may try to configure
another PHY (with phy_init() + phy_power_on()); re-running the
phy_init() goes to the exact same configuration code, re-running the
same hardware configuration on the same set of registers (and bits)
which might impact the result of the msleep for the 1st configuring
thread
3/ sysfs can configure the hardware (though role_store()) and it can
still race with the phy_init()/phy_power_on() APIs calling into the
drivers struct phy_ops
To address these issues, add a spinlock to protect hardware register access
and driver private data structures (e.g., calls to
rcar_gen3_is_any_rphy_initialized()). Checking driver-specific data remains
necessary as all PHY instances share common settings. With this change,
the existing mutex protection is removed and the cleanup.h helpers are
used.
While at it, to keep the code simpler, do not skip
regulator_enable()/regulator_disable() APIs in
rcar_gen3_phy_usb2_power_on()/rcar_gen3_phy_usb2_power_off() as the
regulators enable/disable operations are reference counted anyway.
Fixes: f3b5a8d9b5 ("phy: rcar-gen3-usb2: Add R-Car Gen3 USB2 PHY driver")
Cc: stable@vger.kernel.org
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250507125032.565017-4-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stable-dep-of: 9ce71e85b2 ("phy: renesas: rcar-gen3-usb2: Assert PLL reset on PHY power off")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de76809f60 ]
Commit 08b0ad375c ("phy: renesas: rcar-gen3-usb2: move IRQ registration
to init") moved the IRQ request operation from probe to
struct phy_ops::phy_init API to avoid triggering interrupts (which lead to
register accesses) while the PHY clocks (enabled through runtime PM APIs)
are not active. If this happens, it results in a synchronous abort.
One way to reproduce this issue is by enabling CONFIG_DEBUG_SHIRQ, which
calls free_irq() on driver removal.
Move the IRQ request and free operations back to probe, and take the
runtime PM state into account in IRQ handler. This commit is preparatory
for the subsequent fixes in this series.
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250507125032.565017-3-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stable-dep-of: 9ce71e85b2 ("phy: renesas: rcar-gen3-usb2: Assert PLL reset on PHY power off")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 54c4c58713 upstream.
It has been observed on the Renesas RZ/G3S SoC that unbinding and binding
the PHY driver leads to role autodetection failures. This issue occurs when
PHY 3 is the first initialized PHY. PHY 3 does not have an interrupt
associated with the USB2_INT_ENABLE register (as
rcar_gen3_int_enable[3] = 0). As a result, rcar_gen3_init_otg() is called
to initialize OTG without enabling PHY interrupts.
To resolve this, add rcar_gen3_is_any_otg_rphy_initialized() and call it in
role_store(), role_show(), and rcar_gen3_init_otg(). At the same time,
rcar_gen3_init_otg() is only called when initialization for a PHY with
interrupt bits is in progress. As a result, the
struct rcar_gen3_phy::otg_initialized is no longer needed.
Fixes: 549b6b55b0 ("phy: renesas: rcar-gen3-usb2: enable/disable independent irqs")
Cc: stable@vger.kernel.org
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250507125032.565017-2-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2ea5f4958 upstream.
If device_add() fails, do not use device_unregister() for error
handling. device_unregister() consists two functions: device_del() and
put_device(). device_unregister() should only be called after
device_add() succeeded because device_del() undoes what device_add()
does if successful. Change device_unregister() to put_device() call
before returning from the function.
As comment of device_add() says, 'if device_add() succeeds, you should
call device_del() when you want to get rid of it. If device_add() has
not succeeded, use only put_device() to drop the reference count'.
Found by code review.
Cc: stable@vger.kernel.org
Fixes: 53d2a715c2 ("phy: Add Tegra XUSB pad controller support")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20250303072739.3874987-1-make24@iscas.ac.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b47158fb42 upstream.
The current implementation uses bias_pad_enable as a reference count to
manage the shared bias pad for all UTMI PHYs. However, during system
suspension with connected USB devices, multiple power-down requests for
the UTMI pad result in a mismatch in the reference count, which in turn
produces warnings such as:
[ 237.762967] WARNING: CPU: 10 PID: 1618 at tegra186_utmi_pad_power_down+0x160/0x170
[ 237.763103] Call trace:
[ 237.763104] tegra186_utmi_pad_power_down+0x160/0x170
[ 237.763107] tegra186_utmi_phy_power_off+0x10/0x30
[ 237.763110] phy_power_off+0x48/0x100
[ 237.763113] tegra_xusb_enter_elpg+0x204/0x500
[ 237.763119] tegra_xusb_suspend+0x48/0x140
[ 237.763122] platform_pm_suspend+0x2c/0xb0
[ 237.763125] dpm_run_callback.isra.0+0x20/0xa0
[ 237.763127] __device_suspend+0x118/0x330
[ 237.763129] dpm_suspend+0x10c/0x1f0
[ 237.763130] dpm_suspend_start+0x88/0xb0
[ 237.763132] suspend_devices_and_enter+0x120/0x500
[ 237.763135] pm_suspend+0x1ec/0x270
The root cause was traced back to the dynamic power-down changes
introduced in commit a30951d31b ("xhci: tegra: USB2 pad power controls"),
where the UTMI pad was being powered down without verifying its current
state. This unbalanced behavior led to discrepancies in the reference
count.
To rectify this issue, this patch replaces the single reference counter
with a bitmask, renamed to utmi_pad_enabled. Each bit in the mask
corresponds to one of the four USB2 PHYs, allowing us to track each pad's
enablement status individually.
With this change:
- The bias pad is powered on only when the mask is clear.
- Each UTMI pad is powered on or down based on its corresponding bit
in the mask, preventing redundant operations.
- The overall power state of the shared bias pad is maintained
correctly during suspend/resume cycles.
The mutex used to prevent race conditions during UTMI pad enable/disable
operations has been moved from the tegra186_utmi_bias_pad_power_on/off
functions to the parent functions tegra186_utmi_pad_power_on/down. This
change ensures that there are no race conditions when updating the bitmask.
Cc: stable@vger.kernel.org
Fixes: a30951d31b ("xhci: tegra: USB2 pad power controls")
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20250408030905.990474-1-waynec@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 28dc672a1a ]
Function rk_udphy_dp_hpd_event_trigger will set vogrf let it
trigger HPD interrupt to DP by Type-C. This configuration is only
required when the DP work in Alternate Mode, and called by
typec_mux_set. In standard DP mode, such settings will prevent
the DP from receiving HPD interrupts.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Link: https://lore.kernel.org/r/20250302115257.188774-1-andyshrk@163.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit aecb63e88c upstream.
Ensure the PHY reset and perst is asserted during power-off to
guarantee it is in a reset state upon repeated power-on calls. This
resolves an issue where the PHY may not properly initialize during
subsequent power-on cycles. Power-on will deassert the reset at the
appropriate time after tuning the PHY parameters.
During suspend/resume cycles, we observed that the PHY PLL failed to
lock during resume when the CPU temperature increased from 65C to 75C.
The observed errors were:
phy phy-32f00000.pcie-phy.3: phy poweron failed --> -110
imx6q-pcie 33800000.pcie: waiting for PHY ready timeout!
imx6q-pcie 33800000.pcie: PM: dpm_run_callback(): genpd_resume_noirq+0x0/0x80 returns -110
imx6q-pcie 33800000.pcie: PM: failed to resume noirq: error -110
This resulted in a complete CPU freeze, which is resolved by ensuring
the PHY is in reset during power-on, thus preventing PHY PLL failures.
Cc: stable@vger.kernel.org
Fixes: 1aa97b0022 ("phy: freescale: pcie: Initialize the imx8 pcie standalone phy driver")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250305144355.20364-3-eichest@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f08d1c0856 ]
The phy needs to know its identity in the system (phy0 or phy1 on rk3588)
for some actions and the driver currently contains code abusing of_alias
for that.
Devicetree aliases are always optional and should not be used for core
device functionality, so instead keep a list of phys on a soc in the
of_device_data and find the phy-id by comparing against the mapped
register-base.
Fixes: c4b09c5620 ("phy: phy-rockchip-samsung-hdptx: Add clock provider support")
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20241206103401.1780416-3-heiko@sntech.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ab90f4012 ]
The syscon helper device_node_to_regmap() is used to fetch a regmap
registered to a device node. It also currently creates this regmap
if the node did not already have a regmap associated with it. This
should only be used on "syscon" nodes. This driver is not such a
device and instead uses device_node_to_regmap() on its own node as
a hacky way to create a regmap for itself.
This will not work going forward and so we should create our regmap
the normal way by defining our regmap_config, fetching our memory
resource, then using the normal regmap_init_mmio() function.
Signed-off-by: Andrew Davis <afd@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20250123182234.597665-1-afd@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 55f1a5f7c9 upstream.
Observed VBUS_OVERRIDE & ID_OVERRIDE might be programmed
with unexpected value prior to XUSB PADCTL driver, this
could also occur in virtualization scenario.
For example, UEFI firmware programs ID_OVERRIDE=GROUNDED to set
a type-c port to host mode and keeps the value to kernel.
If the type-c port is connected a usb host, below errors can be
observed right after usb host mode driver gets probed. The errors
would keep until usb role class driver detects the type-c port
as device mode and notifies usb device mode driver to set both
ID_OVERRIDE and VBUS_OVERRIDE to correct value by XUSB PADCTL
driver.
[ 173.765814] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[ 173.765837] usb usb3-port2: config error
Taking virtualization into account, asserting XUSB PADCTL
reset would break XUSB functions used by other guest OS,
hence only reset VBUS & ID OVERRIDE of the port in
utmi_phy_init.
Fixes: bbf711682c ("phy: tegra: xusb: Add Tegra186 support")
Cc: stable@vger.kernel.org
Change-Id: Ic63058d4d49b4a1f8f9ab313196e20ad131cc591
Signed-off-by: BH Hsieh <bhsieh@nvidia.com>
Signed-off-by: Henry Lin <henryl@nvidia.com>
Link: https://lore.kernel.org/r/20250122105943.8057-1-henryl@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fcf5d353b0 ]
A previous patch ensured that USB Type C connector support is enabled,
but it is still possible to build the phy driver without enabling
CONFIG_USB (host support) or CONFIG_USB_GADGET (device support), and
in that case the common helper functions are unavailable:
aarch64-linux-ld: drivers/phy/rockchip/phy-rockchip-usbdp.o: in function `rk_udphy_probe':
phy-rockchip-usbdp.c:(.text+0xe74): undefined reference to `usb_get_maximum_speed'
Select CONFIG_USB_COMMON directly here, like we do in some other phy
drivers, to make sure this is available even when actual USB support
is disabled or in a loadable module that cannot be reached from a
built-in phy driver.
Fixes: 9c79b77964 ("phy: rockchip: fix CONFIG_TYPEC dependency")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250122065249.1390081-1-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fbcbffbac9 upstream.
Currently, the USB port via combophy on the RK3528/RK3588 SoC is broken.
usb usb8-port1: Cannot enable. Maybe the USB cable is bad?
This is due to the combphy of RK3528/RK3588 SoC has multiple resets, but
only "phy resets" need assert and deassert, "apb resets" don't need.
So change the driver to only match the phy resets, which is also what
the vendor kernel does.
Fixes: 7160820d74 ("phy: rockchip: add naneng combo phy for RK3568")
Cc: FUKAUMI Naoki <naoki@radxa.com>
Cc: Michael Zimmermann <sigmaepsilon92@gmail.com>
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20241122073006.99309-2-amadeus@jmu.edu.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4dc48c88fc upstream.
For devm_phy_destroy(), its comment says it needs to invoke phy_destroy()
to destroy the phy, but it will not actually invoke the function since
devres_destroy() does not call devm_phy_consume(), and the missing
phy_destroy() call will cause that the phy fails to be destroyed.
Fortunately, the faulty API has not been used by current kernel tree.
Fix by using devres_release() instead of devres_destroy() within the API.
Fixes: ff76496347 ("drivers: phy: add generic PHY framework")
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20241213-phy_core_fix-v6-3-40ae28f5015a@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe4bfa9b6d upstream.
For devm_phy_put(), its comment says it needs to invoke phy_put() to
release the phy, but it will not actually invoke the function since
devres_destroy() does not call devm_phy_release(), and the missing
phy_put() call will cause:
- The phy fails to be released.
- devm_phy_put() can not fully undo what API devm_phy_get() does.
- Leak refcount of both the module and device for below typical usage:
devm_phy_get(); // or its variant
...
err = do_something();
if (err)
goto err_out;
...
err_out:
devm_phy_put(); // leak refcount here
The file(s) affected by this issue are shown below since they have such
typical usage.
drivers/pci/controller/cadence/pcie-cadence.c
drivers/net/ethernet/ti/am65-cpsw-nuss.c
Fix by using devres_release() instead of devres_destroy() within the API.
Fixes: ff76496347 ("drivers: phy: add generic PHY framework")
Cc: stable@vger.kernel.org
Cc: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: Krzysztof Wilczyński <kw@linux.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20241213-phy_core_fix-v6-1-40ae28f5015a@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Riesch
Michael Dege
Harikrishna Shenoy
Devarsh Thakkar
Tomi Valkeinen
Jonas Karlman
Johan Hovold
Pengyu Luo
Kathiravan Thirumoorthy
Geraldo Nascimento
Luca Weiss
Haotien Hsu
Wayne Chang
Xu Yang
Chenyuan Yang
Cristian Ciocaltea
Algea Cao
Hal Feng
André Draszik
Dmitry Baryshkov
Damon Ding
Andy Yan
Claudiu Beznea
Dan Carpenter
Ma Ke
Stefan Eichenberger
Heiko Stuebner
Andrew Davis
Kaustabh Chakraborty
BH Hsieh
Chukun Pan
Arnd Bergmann
Justin Chen
Zijun Hu