[ Upstream commit 3b384cc74b ]
Looks like the driver sleep pins configuration is unusable. Adding the
sleep pins causes the usb phy to not respond. We need to use the default
pins in probe, and only set sleep pins at phy_mdm6600_device_power_off().
As the modem can also be booted to a serial port mode for firmware
flashing, let's make the pin changes limited to probe and remove. For
probe, we get the default pins automatically. We only need to set the
sleep pins in phy_mdm6600_device_power_off() to prevent the modem from
waking up because the gpio line glitches.
If it turns out that we need a separate state for phy_mdm6600_power_on()
and phy_mdm6600_power_off(), we can use the pinctrl idle state.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Fixes: 2ad2af0816 ("phy: mapphone-mdm6600: Improve phy related runtime PM calls")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230913060433.48373-3-tony@atomide.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19a1d46bd6 ]
inno_write is used to configure 0xaa reg, that also hold the
POST_PLL_POWER_DOWN bit.
When POST_PLL_REFCLK_SEL_TMDS is configured the power down bit is not
taken into consideration.
Fix this by keeping the power down bit until configuration is complete.
Also reorder the reg write order for consistency.
Fixes: 53706a1168 ("phy: add Rockchip Innosilicon hdmi phy")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20230615171005.2251032-5-jonas@kwiboo.se
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5ef343c1d ]
inno_hdmi_phy_rk3328_clk_recalc_rate() is returning a rate not found
in the pre pll config table when the fractal divider is used.
This can prevent proper power_on because a tmdsclock for the new rate
is not found in the pre pll config table.
Fix this by saving and returning a rounded pixel rate that exist
in the pre pll config table.
Fixes: 53706a1168 ("phy: add Rockchip Innosilicon hdmi phy")
Signed-off-by: Zheng Yang <zhengyang@rock-chips.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20230615171005.2251032-3-jonas@kwiboo.se
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 13c088cf36 ]
The size of array 'priv->ports[]' is INNO_PHY_PORT_NUM.
In the for loop, 'i' is used as the index for array 'priv->ports[]'
with a check (i > INNO_PHY_PORT_NUM) which indicates that
INNO_PHY_PORT_NUM is allowed value for 'i' in the same loop.
This > comparison needs to be changed to >=, otherwise it potentially leads
to an out of bounds write on the next iteration through the loop
Fixes: ba8b0ee81f ("phy: add inno-usb2-phy driver for hi3798cv200 SoC")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Link: https://lore.kernel.org/r/20230721090558.3588613-1-harshit.m.mogalapalli@oracle.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a0eb8f9b9 ]
The driver is not enabling the ref clock, which thus gets disabled by
the clk_disable_unused() initcall. This leads to the dwc3 controller
failing to initialize if probed after clk_disable_unused() is called,
for instance when the driver is built as a module.
To fix this, switch to the clk_bulk API to handle both cfg_ahb and ref
clocks at the proper places.
Note that the cfg_ahb clock is currently not used by any device tree
instantiation of the PHY. Work needs to be done separately to fix this.
Link: https://lore.kernel.org/linux-arm-msm/ZEqvy+khHeTkC2hf@fedora/
Fixes: 51e8114f80 ("phy: qcom-snps: Add SNPS USB PHY driver for QCOM based SOCs")
Signed-off-by: Adrien Thierry <athierry@redhat.com>
Link: https://lore.kernel.org/r/20230629144542.14906-3-athierry@redhat.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45d89a344e ]
In the dwc3 core, both system and runtime suspend end up calling
dwc3_suspend_common(). From there, what happens for the PHYs depends on
the USB mode and whether the controller is entering system or runtime
suspend.
HOST mode:
(1) system suspend on a non-wakeup-capable controller
The [1] if branch is taken. dwc3_core_exit() is called, which ends up
calling phy_power_off() and phy_exit(). Those two functions decrease the
PM runtime count at some point, so they will trigger the PHY runtime
sleep (assuming the count is right).
(2) runtime suspend / system suspend on a wakeup-capable controller
The [1] branch is not taken. dwc3_suspend_common() calls
phy_pm_runtime_put_sync(). Assuming the ref count is right, the PHY
runtime suspend op is called.
DEVICE mode:
dwc3_core_exit() is called on both runtime and system sleep
unless the controller is already runtime suspended.
OTG mode:
(1) system suspend : dwc3_core_exit() is called
(2) runtime suspend : do nothing
In host mode, the code seems to make a distinction between 1) runtime
sleep / system sleep for wakeup-capable controller, and 2) system sleep
for non-wakeup-capable controller, where phy_power_off() and phy_exit()
are only called for the latter. This suggests the PHY is not supposed to
be in a fully powered-off state for runtime sleep and system sleep for
wakeup-capable controller.
Moreover, downstream, cfg_ahb_clk only gets disabled for system suspend.
The clocks are disabled by phy->set_suspend() [2] which is only called
in the system sleep path through dwc3_core_exit() [3].
With that in mind, don't disable the clocks during the femto PHY runtime
suspend callback. The clocks will only be disabled during system suspend
for non-wakeup-capable controllers, through dwc3_core_exit().
[1] https://elixir.bootlin.com/linux/v6.4/source/drivers/usb/dwc3/core.c#L1988
[2] https://git.codelinaro.org/clo/la/kernel/msm-5.4/-/blob/LV.AU.1.2.1.r2-05300-gen3meta.0/drivers/usb/phy/phy-msm-snps-hs.c#L524
[3] https://git.codelinaro.org/clo/la/kernel/msm-5.4/-/blob/LV.AU.1.2.1.r2-05300-gen3meta.0/drivers/usb/dwc3/core.c#L1915
Signed-off-by: Adrien Thierry <athierry@redhat.com>
Link: https://lore.kernel.org/r/20230629144542.14906-2-athierry@redhat.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stable-dep-of: 8a0eb8f9b9 ("phy: qcom-snps-femto-v2: properly enable ref clock")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ca651df07 ]
The existing logic in tcphy_get_mode() can cause the phy to be
incorrectly configured to USB UFP or DisplayPort mode when
extcon_get_state returns an error code.
extcon_get_state() can return 0, 1, or a negative error code.
It is possible to get into the failing state with an extcon driver
which does not support the extcon connector id specified as the
second argument to extcon_get_state().
tcphy_get_mode()
->extcon_get_state()
-->find_cable_index_by_id()
--->return -EINVAL;
Fixes: e96be45cb8 ("phy: Add USB Type-C PHY driver for rk3399")
Signed-off-by: Neill Kapron <nkapron@google.com>
Reviewed-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230126001013.3707873-1-nkapron@google.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c7b98de745 upstream.
Drop the confused runtime-suspend type check which effectively broke
runtime PM if the DP child node happens to be parsed before the USB
child node during probe (e.g. due to order of child nodes in the
devicetree).
Instead use the new driver data USB PHY pointer to access the USB
configuration and resources.
Fixes: 52e013d0bf ("phy: qcom-qmp: Add support for DP in USB3+DP combo phy")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221114081346.5116-6-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
[swboyd@chromium.org: Backport to pre-split driver. Note that the
condition is kept so that ufs and pcie don't do anything as before]
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a7d86d14d upstream.
The PHY is powered on during phy-init by setting the SW_PWRDN bit in the
COM_POWER_DOWN_CTRL register and then setting the same bit in the in the
PCS_POWER_DOWN_CONTROL register that belongs to the USB part of the
PHY.
Currently, whether power on succeeds depends on probe order and having
the USB part of the PHY be initialised first. In case the DP part of the
PHY is instead initialised first, the intended power on of the USB block
results in a corrupted DP_PHY register (e.g. DP_PHY_AUX_CFG8).
Add a pointer to the USB part of the PHY to the driver data and use that
to power on the PHY also if the DP part of the PHY is initialised first.
Fixes: 52e013d0bf ("phy: qcom-qmp: Add support for DP in USB3+DP combo phy")
Cc: stable@vger.kernel.org # 5.10
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221114081346.5116-5-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
[swboyd@chromium.org: Backport to pre-split driver, also set usb_phy for
pcie/ufs]
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5d6b1ac56 upstream.
Switch to using the device-managed of_iomap helper to avoid leaking
memory on probe deferral and driver unbind.
Note that this helper checks for already reserved regions and may fail
if there are multiple devices claiming the same memory.
Two bindings currently rely on overlapping mappings for the PCS region
so fallback to non-exclusive mappings for those for now.
Fixes: e78f3d15e1 ("phy: qcom-qmp: new qmp phy driver for qcom-chipsets")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220916102340.11520-7-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
[swboyd@chromium.org: Backport to pre-split driver]
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c3966ced8e ]
Smatch reports the following error:
drivers/phy/qualcomm/phy-qcom-usb-hsic.c:82 qcom_usb_hsic_phy_power_on()
warn: 'uphy->cal_clk' from clk_prepare_enable() not released on lines:
58.
drivers/phy/qualcomm/phy-qcom-usb-hsic.c:82 qcom_usb_hsic_phy_power_on()
warn: 'uphy->cal_sleep_clk' from clk_prepare_enable() not released on
lines: 58.
drivers/phy/qualcomm/phy-qcom-usb-hsic.c:82 qcom_usb_hsic_phy_power_on()
warn: 'uphy->phy_clk' from clk_prepare_enable() not released on lines:
58.
Fix this by calling proper clk_disable_unprepare calls.
Fixes: 0b56e9a7e8 ("phy: Group vendor specific phy drivers")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20220914051334.69282-1-dzm91@hust.edu.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2812227bb ]
The exynos-pcie driver called phy_power_on() before phy_init() for some
historical reasons. However the generic PHY framework assumes that the
proper sequence is to call phy_init() first, then phy_power_on(). The
operations done by both functions should be considered as one action and as
such they are called by the exynos-pcie driver (without doing anything
between them). The initialization is just a sequence of register writes,
which cannot be altered without breaking the hardware operation.
To match the generic PHY framework requirement, simply move all register
writes to the phy_init()/phy_exit() and drop power_on()/power_off()
callbacks. This way the driver will also work with the old (incorrect)
PHY initialization call sequence.
Link: https://lore.kernel.org/r/20220628220409.26545-1-m.szyprowski@samsung.com
Reported-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-By: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c8045d48d ]
If clk_prepare_enable() fails we call clk_disable_unprepare()
in the error path what results in a warning that the clock
is disabled and unprepared already.
And if we fail later in phy_g12a_usb3_pcie_probe() then we
bail out w/o calling clk_disable_unprepare().
This patch fixes both errors.
Fixes: 36077e16c0 ("phy: amlogic: Add Amlogic G12A USB3 + PCIE Combo PHY Driver")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/8e416f95-1084-ee28-860e-7884f7fa2e32@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d644e0d798 ]
The pm_runtime_enable will increase power disable depth.
If the probe fails, we should use pm_runtime_disable() to balance
pm_runtime_enable(). And use pm_runtime_dont_use_autosuspend() to
undo pm_runtime_use_autosuspend()
In the PM Runtime docs:
Drivers in ->remove() callback should undo the runtime PM changes done
in ->probe(). Usually this means calling pm_runtime_disable(),
pm_runtime_dont_use_autosuspend() etc.
We should do this in error handling.
Fixes: f7f50b2a7b ("phy: mapphone-mdm6600: Add runtime PM support for n_gsm on USB suspend")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220301024615.31899-1-linmq006@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f1dedf089 ]
Use reset_control_rearm() call if an error occurs in case
phy_meson8b_usb2_power_on() fails after reset() has been called, or in
case phy_meson8b_usb2_power_off() is called i.e the resource is no longer
used and the reset line may be triggered again by other devices.
reset_control_rearm() keeps use of triggered_count sane in the reset
framework, use of reset_control_reset() on shared reset line should
be balanced with reset_control_rearm().
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reported-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220111095255.176141-4-aouledameur@baylibre.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32942d33d6 ]
Just like every other family BCM4908 should get its own enum value. That
is required to properly handle it in chipset conditional code.
The real change is excluding BCM4908 from the PLL reprogramming code
(see brcmusb_usb3_pll_54mhz()). I'm not sure what's the BCM4908
reference clock frequency but:
1. BCM4908 custom driver from Broadcom's SDK doesn't reprogram PLL
2. Doing that in Linux driver stopped PHY handling some USB 3.0 devices
This change makes USB 3.0 PHY recognize e.g.:
1. 04e8:6860 - Samsung Electronics Co., Ltd Galaxy series, misc. (MTP mode)
2. 1058:259f - Western Digital My Passport 259F
Broadcom's STB SoCs come with a set of SUN_TOP_CTRL_* registers that
allow reading chip family and product ids. Such a block & register is
missing on BCM4908 so this commit introduces "compatible" string
specific binding.
Fixes: 4b402fa8e0 ("phy: phy-brcm-usb: support PHY on the BCM4908")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220218172459.10431-1-zajec5@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
