commit ea3715941a upstream.
This add a mapping for the airplane mode button on the TUXEDO Pulse Gen3.
While it is physically a key it behaves more like a switch, sending a key
down on first press and a key up on 2nd press. Therefor the switch event
is used here. Besides this behaviour it uses the HID usage-id 0xc6
(Wireless Radio Button) and not 0xc8 (Wireless Radio Slider Switch), but
since neither 0xc6 nor 0xc8 are currently implemented at all in
soc_button_array this not to standard behaviour is not put behind a quirk
for the moment.
Signed-off-by: Christoffer Sandberg <cs@tuxedo.de>
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Link: https://lore.kernel.org/r/20231215171718.80229-1-wse@tuxedocomputers.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5030b2fe6a ]
Touch controllers need some time after receiving reset command for the
firmware to finish re-initializing and be ready to respond to commands
from the host. The driver already had handling for the post-reset delay
for I2C and SPI transports, this change adds the handling to
SMBus-connected devices.
SMBus devices are peculiar because they implement legacy PS/2
compatibility mode, so reset is actually issued by psmouse driver on the
associated serio port, after which the control is passed to the RMI4
driver with SMBus companion device.
Note that originally the delay was added to psmouse driver in
92e24e0e57 ("Input: psmouse - add delay when deactivating for SMBus
mode"), but that resulted in an unwanted delay in "fast" reconnect
handler for the serio port, so it was decided to revert the patch and
have the delay being handled in the RMI4 driver, similar to the other
transports.
Tested-by: Jeffery Miller <jefferymiller@google.com>
Link: https://lore.kernel.org/r/ZR1yUFJ8a9Zt606N@penguin
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 423622a90a upstream.
Add a special case for gpio_count == 1 && gpio_int_idx == 0 to
goodix_add_acpi_gpio_mappings().
It seems that on newer x86/ACPI devices the reset and irq GPIOs are no
longer listed as GPIO resources instead there is only 1 GpioInt resource
and _PS0 does the whole reset sequence for us.
This means that we must call acpi_device_fix_up_power() on these devices
to ensure that the chip is reset before we try to use it.
This part was already fixed in commit 3de93e6ed2 ("Input: goodix - call
acpi_device_fix_up_power() in some cases") by adding a call to
acpi_device_fix_up_power() to the generic "Unexpected ACPI resources"
catch all.
But it turns out that this case on some hw needs some more special
handling. Specifically the firmware may bootup with the IRQ pin in
output mode. The reset sequence from ACPI _PS0 (executed by
acpi_device_fix_up_power()) should put the pin in input mode,
but the GPIO subsystem has cached the direction at bootup, causing
request_irq() to fail due to gpiochip_lock_as_irq() failure:
[ 9.119864] Goodix-TS i2c-GDIX1002:00: Unexpected ACPI resources: gpio_count 1, gpio_int_idx 0
[ 9.317443] Goodix-TS i2c-GDIX1002:00: ID 911, version: 1060
[ 9.321902] input: Goodix Capacitive TouchScreen as /devices/pci0000:00/0000:00:17.0/i2c_designware.4/i2c-5/i2c-GDIX1002:00/input/input8
[ 9.327840] gpio gpiochip0: (INT3453:00): gpiochip_lock_as_irq: tried to flag a GPIO set as output for IRQ
[ 9.327856] gpio gpiochip0: (INT3453:00): unable to lock HW IRQ 26 for IRQ
[ 9.327861] genirq: Failed to request resources for GDIX1002:00 (irq 131) on irqchip intel-gpio
[ 9.327912] Goodix-TS i2c-GDIX1002:00: request IRQ failed: -5
Fix this by adding a special case for gpio_count == 1 && gpio_int_idx == 0
which adds an ACPI GPIO lookup table for the int GPIO even though we cannot
use it for reset purposes (as there is no reset GPIO).
Adding the lookup will make the gpiod_int = gpiod_get(..., GPIOD_IN) call
succeed, which will explicitly set the direction to input fixing the issue.
Note this re-uses the acpi_goodix_int_first_gpios[] lookup table, since
there is only 1 GPIO in the ACPI resources the reset entry in that
lookup table will amount to a no-op.
Reported-and-tested-by: Michael Smith <1973.mjsmith@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231003215144.69527-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 80f39e1c27 upstream.
In the initial boot stage the integrated keyboard of Fujitsu Lifebook E5411
refuses to work and it's not possible to type for example a dm-crypt
passphrase without the help of an external keyboard.
i8042.nomux kernel parameter resolves this issue but using that a PS/2
mouse is detected. This input device is unused even when the i2c-hid-acpi
kernel module is blacklisted making the integrated ELAN touchpad
(04F3:308A) not working at all.
Since the integrated touchpad is managed by the i2c_designware input
driver in the Linux kernel and you can't find a PS/2 mouse port on the
computer I think it's safe to not use the PS/2 mouse port at all.
Signed-off-by: Szilard Fabian <szfabian@bluemarch.art>
Link: https://lore.kernel.org/r/20231004011749.101789-1-szfabian@bluemarch.art
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e2cb5cc822 upstream.
When the SMBus connection is attempted psmouse_smbus_init() sets
the fast_reconnect pointer to psmouse_smbus_reconnecti(). If SMBus
initialization fails, elantech_setup_ps2() and synaptics_init_ps2() will
fallback to PS/2 mode, replacing the psmouse private data. This can cause
issues on resume, since psmouse_smbus_reconnect() expects to find an
instance of struct psmouse_smbus_dev in psmouse->private.
The issue was uncovered when in 92e24e0e57 ("Input: psmouse - add
delay when deactivating for SMBus mode") psmouse_smbus_reconnect()
started attempting to use more of the data structure. The commit was
since reverted, not because it was at fault, but because there was found
a better way of doing what it was attempting to do.
Fix the problem by resetting the fast_reconnect pointer in psmouse
structure in elantech_setup_ps2() and synaptics_init_ps2() when the PS/2
mode is used.
Reported-by: Thorsten Leemhuis <linux@leemhuis.info>
Tested-by: Thorsten Leemhuis <linux@leemhuis.info>
Signed-off-by: Jeffery Miller <jefferymiller@google.com>
Fixes: bf232e460a ("Input: psmouse-smbus - allow to control psmouse_deactivate")
Link: https://lore.kernel.org/r/20231005002249.554877-1-jefferymiller@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit eb09074bdb ]
The touchpad of this device is both connected via PS/2 and i2c. This causes
strange behavior when both driver fight for control. The easy fix is to
prevent the PS/2 driver from accessing the mouse port as the full feature
set of the touchpad is only supported in the i2c interface anyway.
The strange behavior in this case is, that when an external screen is
connected and the notebook is closed, the pointer on the external screen is
moving to the lower right corner. When the notebook is opened again, this
movement stops, but the touchpad clicks are unresponsive afterwards until
reboot.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230607173331.851192-1-wse@tuxedocomputers.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20a99a291d ]
Some devices have a wrong entry in their button array which points to
a GPIO which is required in another driver, so soc_button_array must
not claim it.
A specific example of this is the Lenovo Yoga Book X90F / X90L,
where the PNP0C40 home button entry points to a GPIO which is not
a home button and which is required by the lenovo-yogabook driver.
Add a DMI quirk table which can specify an ACPI GPIO resource index which
should be skipped; and add an entry for the Lenovo Yoga Book X90F / X90L
to this new DMI quirk table.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230414072116.4497-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit feee70f456 upstream.
While doing my research to improve the xpad device names I noticed
that the 1532:0037 VID/PID seems to be used by the DeathAdder 2013,
so that Razer Sabertooth instance looked wrong and very suspect to
me. I didn't see any mention in the official drivers, either.
After doing more research, it turns out that the xpad list
is used by many other projects (like Steam) as-is [1], this
issue was reported [2] and Valve/Sam Lantinga fixed it [3]:
[1]: dcc5eef0e2/src/joystick/controller_type.h (L251)
[2]: https://steamcommunity.com/app/353380/discussions/0/1743392486228754770/
[3]: https://hg.libsdl.org/SDL/rev/29809f6f0271
(With multiple Internet users reporting similar issues, not linked here)
After not being able to find the correct VID/PID combination anywhere
on the Internet and not receiving any reply from Razer support I did
some additional detective work, it seems like it presents itself as
"Razer Sabertooth Gaming Controller (XBOX360)", code 1689:FE00.
Leaving us with this:
* Razer Sabertooth (1689:fe00)
* Razer Sabertooth Elite (24c6:5d04)
* Razer DeathAdder 2013 (1532:0037) [note: not a gamepad]
So, to sum things up; remove this conflicting/duplicate entry:
{ 0x1532, 0x0037, "Razer Sabertooth", 0, XTYPE_XBOX360 },
As the real/correct one is already present there, even if
the Internet as a whole insists on presenting it as the
Razer Sabertooth Elite, which (by all accounts) is not:
{ 0x1689, 0xfe00, "Razer Sabertooth", 0, XTYPE_XBOX360 },
Actual change in SDL2 referencing this kernel issue:
e5e5416975
For more information of the device, take a look here:
https://github.com/xboxdrv/xboxdrv/pull/59
You can see a lsusb dump here: https://github.com/xboxdrv/xboxdrv/files/76581/Qa6dBcrv.txt
Fixes: f554f619b7 ("Input: xpad - sync device IDs with xboxdrv")
Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Reviewed-by: Cameron Gutman <aicommander@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/5c12dbdb-5774-fc68-5c58-ca596383663e@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a0432bab6 upstream.
The Android Lenovo Yoga Book X90F / X90L uses the same goodix touchscreen
with 9 bytes touch reports for its touch keyboard as the already supported
Windows Lenovo Yoga Book X91F/L, add a DMI match for this to
the nine_bytes_report DMI table.
When the quirk for the X91F/L was initially added it was written to
also apply to the X90F/L but this does not work because the Android
version of the Yoga Book uses completely different DMI strings.
Also adjust the X91F/L quirk to reflect that it only applies to
the X91F/L models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20230315134442.71787-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 754ff5060d upstream.
The AlpsPS/2 code previously relied on the assumption that `char` is a
signed type, which was true on x86 platforms (the only place where this
driver is used) before kernel 6.2. However, on 6.2 and later, this
assumption is broken due to the introduction of -funsigned-char as a new
global compiler flag.
Fix this by explicitly specifying the signedness of `char` when sign
extending the values received from the device.
Fixes: f3f33c6776 ("Input: alps - Rushmore and v7 resolution support")
Signed-off-by: msizanoen <msizanoen@qtmlabs.xyz>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230320045228.182259-1-msizanoen@qtmlabs.xyz
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a85fbd6498 ]
As can be seen in elants_i2c_power_off(), we want the reset GPIO
asserted when power is off. The reset GPIO is active low so we need
the reset line logic low when power is off to avoid leakage.
We have a problem, though, at probe time. At probe time we haven't
powered the regulators on yet but we have:
devm_gpiod_get(&client->dev, "reset", GPIOD_OUT_LOW);
While that _looks_ right, it turns out that it's not. The
GPIOD_OUT_LOW doesn't mean to init the GPIO to low. It means init the
GPIO to "not asserted". Since this is an active low GPIO that inits it
to be high.
Let's fix this to properly init the GPIO. Now after both probe and
power off the state of the GPIO is consistent (it's "asserted" or
level low).
Once we fix this, we can see that at power on time we no longer to
assert the reset GPIO as the first thing. The reset GPIO is _always_
asserted before powering on. Let's fix powering on to account for
this.
Fixes: afe10358e4 ("Input: elants_i2c - wire up regulator support")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20221117123805.1.I9959ac561dd6e1e8e1ce7085e4de6167b27c574f@changeid
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e13757f524 ]
Like on the Acer Switch 10 SW5-012, the Acer Switch V 10 SW5-017's _LID
method messes with home- and power-button GPIO IRQ settings, causing an
IRQ storm.
Add a quirk entry for the Acer Switch V 10 to the dmi_use_low_level_irq[]
DMI quirk list, to use low-level IRQs on this model, fixing the IRQ storm.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221106215320.67109-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e9ada1d0e ]
It seems that the Windows drivers for the ACPI0011 soc_button_array
device use low level triggered IRQs rather then using edge triggering.
Some ACPI tables depend on this, directly poking the GPIO controller's
registers to clear the trigger type when closing a laptop's/2-in-1's lid
and re-instating the trigger when opening the lid again.
Linux sets the edge/level on which to trigger to both low+high since
it is using edge type IRQs, the ACPI tables then ends up also setting
the bit for level IRQs and since both low and high level have been
selected by Linux we get an IRQ storm leading to soft lockups.
As a workaround for this the soc_button_array already contains
a DMI quirk table with device models known to have this issue.
Add a module parameter for this so that users can easily test if their
device is affected too and so that they can use the module parameter
as a workaround.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221106215320.67109-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7e37cc624 ]
On ACPI systems (irq_pin_access_method == IRQ_PIN_ACCESS_ACPI_*) the driver
does not reset the controller at probe time, because sometimes the system
firmware loads a config and resetting might loose this config.
On the Nanote UMPC-01 device OTOH the config is in flash of the controller,
the controller needs a reset to load this; and the system firmware does not
reset the controller on a cold boot.
To fix the Nanote UMPC-01 touchscreen not working on a cold boot, try
resetting the controller and then re-reading the config when encountering
a config with 0 width/height/max_touch_num value and the controller has
not already been reset by goodix_ts_probe().
This should be safe to do in general because normally we should never
encounter a config with 0 width/height/max_touch_num. Doing this in
general not only avoids the need for a DMI quirk, but also might help
other systems.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20221025122930.421377-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a17b984115 upstream.
Suspending and resuming the system can sometimes cause the out
URB to get hung after a reset_resume. This causes LED setting
and force feedback to break on resume. To avoid this, just drop
the reset_resume callback so the USB core rebinds xpad to the
wireless pads on resume if a reset happened.
A nice side effect of this change is the LED ring on wireless
controllers is now set correctly on system resume.
Cc: stable@vger.kernel.org
Fixes: 4220f7db1e ("Input: xpad - workaround dead irq_out after suspend/ resume")
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Link: https://lore.kernel.org/r/20220818154411.510308-3-rojtberg@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e62563db85 upstream.
Both i.MX6 and i.MX8 reference manuals list 0xBF8 as SNVS_HPVIDR1
(chapters 57.9 and 6.4.5 respectively).
Without this, trying to read the revision number results in 0 on
all revisions, causing the i.MX6 quirk to apply on all platforms,
which in turn causes the driver to synthesise power button release
events instead of passing the real one as they happen even on
platforms like i.MX8 where that's not wanted.
Fixes: 1a26c92071 ("Input: snvs_pwrkey - send key events for i.MX6 S, DL and Q")
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/4599101.ElGaqSPkdT@pliszka
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
