The existing i3c_master_enec_locked() wrapper always treats a NACKed
ENEC CCC as a failure (M2 error). However, broadcasting ENEC to enable
Hot-Join is legitimately useful even when no I3C devices are currently
present on the bus, in which case the broadcast will be NACKed and
should not be reported as an error.
The underlying helper i3c_master_enec_disec_locked() already accepts a
suppress_m2 flag that lets callers ignore such NACKs. Expose it so that
a subsequent patch enabling Hot-Join events can issue ENEC with M2
suppression.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260608054312.10604-8-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Master drivers may invoke i3c_master_do_daa_ext() during resume to
re-run Dynamic Address Assignment. As well as assigning addresses to
any newly arrived devices, this restores the dynamic address of devices
that lost it across system suspend, so it has to run as part of the
controller's resume path.
A side effect of i3c_master_do_daa_ext() today is that it also
registers any newly discovered I3C devices with the driver model
inline, via i3c_master_register_new_i3c_devs(). Doing that from the
resume path is problematic: a hot-join-capable device may join the bus
during this same DAA, and registering it immediately would push driver
model work (probing, sysfs, etc.) into the controller's resume context,
where the rest of the system is not yet fully resumed and the
controller driver is still partway through its own resume sequence.
Decouple discovery from registration: add a reg_work work item to
struct i3c_master_controller and have i3c_master_do_daa_ext() queue it
on master->wq (the freezable workqueue) instead of calling
i3c_master_register_new_i3c_devs() directly. The worker performs the
registration only when the controller is not shutting_down, and is
cancelled alongside hj_work in i3c_master_shutdown(). Because wq is
freezable, any newly observed devices end up being registered after
the system has finished resuming.
i3c_master_register() also routes its initial post-bus-init registration
through reg_work, using flush_work() to keep probe-time behavior
synchronous. This keeps a single registration code path and ensures the
worker is the only writer of desc->dev.
Fixes: 3a379bbcea ("i3c: Add core I3C infrastructure")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260608054312.10604-7-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
System shutdown invokes each device's bus shutdown callback to quiesce
hardware, but the I3C bus type does not currently implement one. As a
result, on shutdown the controller's Hot-Join work and any in-flight
i3c_master_do_daa() can keep running (or be newly triggered) while the
rest of the system is being torn down.
A similar window exists at i3c_master_unregister() time: cancel_work_sync()
on hj_work prevents queued work from completing, but does not stop a
fresh Hot-Join IBI from re-queueing the worker, nor a concurrent sysfs
writer from toggling Hot-Join via i3c_set_hotjoin().
Introduce a single "shutting down" gate in the I3C core, set under the
bus maintenance lock so it is observed by any in-progress DAA path
before pending work is cancelled. Install an i3c_bus_type shutdown
callback that engages this gate for master devices during system
shutdown, and use the same gate in i3c_master_unregister() so both
paths get identical guarantees.
Once the gate is engaged, the Hot-Join worker, i3c_master_do_daa_ext()
and i3c_set_hotjoin() all bail out cleanly, so Hot-Join IBIs that race
with shutdown become no-ops, direct DAA callers see -ENODEV, and sysfs
writers can no longer re-enable Hot-Join through ops->enable_hotjoin()
while the controller is going away.
No functional change for the steady-state runtime path; the new checks
only take effect once the controller has been marked as shutting down.
Note, this patch depends on patch "i3c: master: Consolidate Hot-Join DAA
work in the core".
Fixes: 3a379bbcea ("i3c: Add core I3C infrastructure")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260608054312.10604-5-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Three master drivers (dw-i3c-master, i3c-master-cdns, svc-i3c-master)
each carry an essentially identical Hot-Join handler: a struct
work_struct embedded in their private state, a work function that just
calls i3c_master_do_daa() on the embedded i3c_master_controller, plus
matching INIT_WORK()/cancel_work_sync() boilerplate in probe/remove (and
shutdown for dw-i3c). The IBI/ISR paths then queue that work onto
master->wq, which already lives in the core.
Move this pattern into the I3C core:
- Add struct work_struct hj_work to struct i3c_master_controller and
initialise it in i3c_master_register() with a core-provided handler
i3c_master_hj_work_fn() that performs i3c_master_do_daa().
- Cancel the work in i3c_master_unregister() so all controllers get
correct teardown ordering against the workqueue for free.
- Export i3c_master_queue_hotjoin() as the single entry point drivers
call from their Hot-Join IBI handler.
Convert the three existing users to the new API: drop their private
hj_work fields, work functions, INIT_WORK() and cancel_work_sync()
calls, and replace the queue_work(master->wq, &drv->hj_work) call sites
with i3c_master_queue_hotjoin(&drv->base). The dw-i3c shutdown path
still needs to flush pending Hot-Join work before tearing down the
hardware, so it is updated to cancel master->base.hj_work directly.
No functional change intended: the work is still queued on the same
master->wq, runs the same i3c_master_do_daa(), and is cancelled at
controller teardown. Future Hot-Join improvements now only need to
be made in one place.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260608054312.10604-4-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The I3C master workqueue (master->wq) is used to defer work that needs
thread context and the bus maintenance lock, most notably Hot Join
processing (which calls i3c_master_do_daa() to assign dynamic addresses
to newly joined devices).
Currently the workqueue keeps running across system suspend, which can
race with the suspend path:
- do_daa() may execute after the controller has been suspended,
issuing bus transactions on a powered-down or otherwise unusable
controller.
- New I3C devices can be enumerated and added to the bus mid-suspend,
registering driver model objects at a point where the I3C subsystem
and its consumers are not prepared to handle them.
Mark the workqueue WQ_FREEZABLE so its workers are frozen for the
duration of system suspend/hibernate and resumed afterwards. This
naturally defers any pending or newly queued Hot Join work until the
system (and the controller) is fully resumed, closing both races
without adding explicit suspend/resume synchronization in the master
drivers.
Update the kerneldoc for struct i3c_master_controller::wq to reflect
that the workqueue is freezable.
Fixes: 3a379bbcea ("i3c: Add core I3C infrastructure")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260608054312.10604-2-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
After system hibernation, I3C Dynamic Addresses may be reassigned at boot
and no longer match the values recorded before suspend. Introduce
i3c_master_do_daa_ext() to handle this situation.
The restore procedure is straightforward: issue a Reset Dynamic Address
Assignment (RSTDAA), then run the standard DAA sequence. The existing DAA
logic already supports detecting and updating devices whose dynamic
addresses differ from previously known values.
Refactor the DAA path by introducing a shared helper used by both the
normal i3c_master_do_daa() path and the new extended restore function,
and correct the kernel-doc in the process.
Export i3c_master_do_daa_ext() so that master drivers can invoke it from
their PM restore callbacks.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260123063325.8210-2-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Master drivers currently manage Runtime PM individually, but all require
runtime resume for bus operations. This can be centralized in common code.
Add optional Runtime PM support to ensure the parent device is runtime
resumed before bus operations and auto-suspended afterward.
Notably, do not call ->bus_cleanup() if runtime resume fails. Master
drivers that opt-in to core runtime PM support must take that into account.
Also provide an option to allow IBIs and hot-joins while runtime suspended.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260113072702.16268-20-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Document sysfs attribute dev_nack_retry_cnt that controls the number of
automatic retries performed by the I3C controller when a target device
returns a NACK
Add a `dev_nack_retry_count` sysfs attribute to allow reading and updating
the device NACK retry count. A new `dev_nack_retry_count` field and an
optional `set_dev_nack_retry()` callback are added to
i3c_master_controller. The attribute is created only when the callback is
implemented.
Updates are applied under the I3C bus maintenance lock to ensure safe
hardware reconfiguration.
Signed-off-by: Adrian Ng Ho Yin <adrianhoyin.ng@altera.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/3c4b5082bde64024fc383c44bebeef89ad3c7ed3.1765529948.git.adrianhoyin.ng@altera.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Rename struct i3c_priv_xfer to struct i3c_xfer, since private xfer in the
I3C spec refers only to SDR transfers. Ref: i3c spec ver1.2, section 3,
Technical Overview.
i3c_xfer will be used for both SDR and HDR.
Rename enum i3c_hdr_mode to i3c_xfer_mode. Previous definition need match
CCC GET_CAP1 bit position. Use 31 as SDR transfer mode.
Add i3c_device_do_xfers() with an xfer mode argument, while keeping
i3c_device_do_priv_xfers() as a wrapper that calls i3c_device_do_xfers()
with I3C_SDR for backward compatibility.
Introduce a 'cmd' field in struct i3c_xfer as an anonymous union with
'rnw', since HDR mode uses read/write commands instead of the SDR address
bit.
Add .i3c_xfers() callback for master controllers. If not implemented, fall
back to SDR with .priv_xfers(). The .priv_xfers() API can be removed once
all controllers switch to .i3c_xfers().
Add 'mode_mask' bitmask to advertise controller capability.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20251106-i3c_ddr-v11-1-33a6a66ed095@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Some I3C controllers such as MIPI I3C HCI may pad the last DWORD (32-bit)
with stale data from the RX FIFO in DMA transfers if the receive length
is not DWORD aligned and when the device DMA is IOMMU mapped.
In such a case, a properly sized bounce buffer is required in order to
avoid possible data corruption. In a review discussion, proposal was to
have a common helpers in I3C core for DMA mapping and bounce buffer
handling.
Drivers may use the helper i3c_master_dma_map_single() to map a buffer
for a DMA transfer. It internally allocates a bounce buffer if buffer is
not DMA'able or when the driver requires it for a transfer.
Helper i3c_master_dma_unmap_single() does the needed cleanups and
data copying from the bounce buffer.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250822105630.2820009-2-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When CONFIG_I3C is disabled and the i3c_i2c_driver_register() happens
to not be inlined, any driver calling it still references the i3c_driver
instance, which then causes a link failure:
x86_64-linux-ld: drivers/hwmon/lm75.o: in function `lm75_i3c_reg_read':
lm75.c:(.text+0xc61): undefined reference to `i3cdev_to_dev'
x86_64-linux-ld: lm75.c:(.text+0xd25): undefined reference to `i3c_device_do_priv_xfers'
x86_64-linux-ld: lm75.c:(.text+0xdd8): undefined reference to `i3c_device_do_priv_xfers'
This issue was part of the original i3c code, but only now caused problems
when i3c support got added to lm75.
Change the 'inline' annotations in the header to '__always_inline' to
ensure that the dead-code-elimination pass in the compiler can optimize
it out as intended.
Fixes: 6071d10413 ("hwmon: (lm75) add I3C support for P3T1755")
Fixes: 3a379bbcea ("i3c: Add core I3C infrastructure")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250725090609.2456262-1-arnd@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Extend the address status bit to 4 and introduce the
I3C_ADDR_SLOT_EXT_DESIRED macro to indicate that a device prefers a
specific address. This is generally set by the 'assigned-address' in the
device tree source (dts) file.
┌────┬─────────────┬───┬─────────┬───┐
│S/Sr│ 7'h7E RnW=0 │ACK│ ENTDAA │ T ├────┐
└────┴─────────────┴───┴─────────┴───┘ │
┌─────────────────────────────────────────┘
│ ┌──┬─────────────┬───┬─────────────────┬────────────────┬───┬─────────┐
└─►│Sr│7'h7E RnW=1 │ACK│48bit UID BCR DCR│Assign 7bit Addr│PAR│ ACK/NACK│
└──┴─────────────┴───┴─────────────────┴────────────────┴───┴─────────┘
Some master controllers (such as HCI) need to prepare the entire above
transaction before sending it out to the I3C bus. This means that a 7-bit
dynamic address needs to be allocated before knowing the target device's
UID information.
However, some I3C targets may request specific addresses (called as
"init_dyn_addr"), which is typically specified by the DT-'s
assigned-address property. Lower addresses having higher IBI priority. If
it is available, i3c_bus_get_free_addr() preferably return a free address
that is not in the list of desired addresses (called as "init_dyn_addr").
This allows the device with the "init_dyn_addr" to switch to its
"init_dyn_addr" when it hot-joins the I3C bus. Otherwise, if the
"init_dyn_addr" is already in use by another I3C device, the target device
will not be able to switch to its desired address.
If the previous step fails, fallback returning one of the remaining
unassigned address, regardless of its state in the desired list.
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20241021-i3c_dts_assign-v8-2-4098b8bde01e@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Pull i3c updates from Alexandre Belloni:
"This cycle, there are new features for the Designware controller and
fixes for the other IPs:
- dw: optional apb clock and power management support, IBI handling
fixes
- mipi-i3c-hci: IBI handling fixes
- svc: a few fixes"
* tag 'i3c/for-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
dt-bindings: i3c: add header for generic I3C flags
i3c: master: svc: Fix error code in svc_i3c_master_do_daa_locked()
i3c: master: Enhance i3c_bus_type visibility for device searching & event monitoring
i3c: dw: Add power management support
i3c: dw: Add some functions for reusability
i3c: dw: Save timing registers and other values
i3c: master: svc: Improve DAA STOP handle code logic
i3c: dw: Add optional apb clock
i3c: dw: Use new *_enabled clk API
dt-bindings: i3c: dw: Add apb clock binding
i3c: master: svc: Convert comma to semicolon
i3c: mipi-i3c-hci: Round IBI data chunk size to HW supported value
i3c: mipi-i3c-hci: Error out instead on BUG_ON() in IBI DMA setup
i3c: mipi-i3c-hci: Set IBI Status and Data Ring base addresses
i3c: mipi-i3c-hci: Switch to lower_32_bits()/upper_32_bits() helpers
i3c: dw: Remove ibi_capable property
i3c: dw: Fix IBI intr programming
i3c: dw: Fix clearing queue thld
i3c: mipi-i3c-hci: Fix number of DAT/DCT entries for HCI versions < 1.1
i3c: master: svc: resend target address when get NACK
In the match() callback, the struct device_driver * should not be
changed, so change the function callback to be a const *. This is one
step of many towards making the driver core safe to have struct
device_driver in read-only memory.
Because the match() callback is in all busses, all busses are modified
to handle this properly. This does entail switching some container_of()
calls to container_of_const() to properly handle the constant *.
For some busses, like PCI and USB and HV, the const * is cast away in
the match callback as those busses do want to modify those structures at
this point in time (they have a local lock in the driver structure.)
That will have to be changed in the future if they wish to have their
struct device * in read-only-memory.
Cc: Rafael J. Wysocki <rafael@kernel.org>
Reviewed-by: Alex Elder <elder@kernel.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/2024070136-wrongdoer-busily-01e8@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix warning found by
'scripts/kernel-doc -v -none include/linux/i3c/master.h'
include/linux/i3c/master.h:457: warning: Function parameter or member 'enable_hotjoin' not described in 'i3c_master_controller_ops'
include/linux/i3c/master.h:457: warning: Function parameter or member 'disable_hotjoin' not described in 'i3c_master_controller_ops'
include/linux/i3c/master.h:499: warning: Function parameter or member 'hotjoin' not described in 'i3c_master_controller'
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20240109052548.2128133-1-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In MIPI I3C Specification:
"Ninth Bit of SDR Target Returned (Read) Data as End-of-Data: In I2C, the
ninth Data bit from Target to Controller is an ACK by the Controller. By
contrast, in I3C this bit allows the Target to end a Read, and allows the
Controller to Abort a Read. In SDR terms, the ninth bit of Read data is
referred to as the T-Bit (for ‘Transition’)"
I3C allow devices early terminate data transfer. So need "actual_len" field
to indicate how much get by i3c_priv_xfer.
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231201222532.2431484-4-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Pull i3c updates from Alexandre Belloni:
"There are now more fixes because as stated in my previous pull
request, people now have access to actual hardware.
Core:
- handle IBI in the proper order
Drivers:
- cdns: fix status register access
- mipi-i3c-hci: many fixes now that the driver has been actually
tested
- svc: many IBI fixes, correct compatible string, fix hot join corner
cases"
* tag 'i3c/for-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux: (29 commits)
i3c: master: handle IBIs in order they came
i3c: master: mipi-i3c-hci: Fix a kernel panic for accessing DAT_data.
i3c: master: svc: fix compatibility string mismatch with binding doc
i3c: master: svc: fix random hot join failure since timeout error
i3c: master: svc: fix SDA keep low when polling IBIWON timeout happen
i3c: master: svc: fix check wrong status register in irq handler
i3c: master: svc: fix ibi may not return mandatory data byte
i3c: master: svc: fix wrong data return when IBI happen during start frame
i3c: master: svc: fix race condition in ibi work thread
i3c: Fix typo "Provisional ID" to "Provisioned ID"
i3c: Fix potential refcount leak in i3c_master_register_new_i3c_devs
i3c: mipi-i3c-hci: Resume controller after aborted transfer
i3c: mipi-i3c-hci: Resume controller explicitly
i3c: mipi-i3c-hci: Fix missing xfer->completion in hci_cmd_v1_daa()
i3c: mipi-i3c-hci: Do not unmap region not mapped for transfer
i3c: mipi-i3c-hci: Set number of SW enabled Ring Bundles earlier
i3c: mipi-i3c-hci: Fix race between bus cleanup and interrupt
i3c: mipi-i3c-hci: Set ring start request together with enable
i3c: mipi-i3c-hci: Remove BUG() when Ring Abort request times out
i3c: mipi-i3c-hci: Fix out of bounds access in hci_dma_irq_handler
...
IBI shall be handled in order they appear on the bus. Otherwise could hit
case when order of handling them in device driver will be different. It may
lead to invalid assembling fragmented packets or events order broken.
Added separate workqueue with option WQ_MEM_RECLAIM for each device driver.
This ensures IBI handling order and improves IBI handling performance: IBI
handlers for device B are not blocked by IBI handlers for device A.
Original solution (single workqueue in main driver) was able to handle also
general IBI (not related to specific device) like HJ or MR. So leaving this
for such purposes.
Signed-off-by: Zbigniew Lukwinski <zbigniew.lukwinski@linux.intel.com>
Link: https://lore.kernel.org/r/20231015222334.1652401-2-zbigniew.lukwinski@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Because not all I3C drivers have the hot-join feature ready, and
especially not all I3C devices support hot-join feature, exporting
SETDASA method could be useful. With this function, the I3C controller
could perform a DAA to I3C devices when users decide to turn these I3C
devices off and on again during run-time.
Tested: This change has been tested with turnning off an I3C device and
turning on it again during run-time. The device driver calls SETDASA
method to perform DAA to the device. And communication between I3C
controller and device is set up again correctly.
Signed-off-by: Jack Chen <zenghuchen@google.com>
Link: https://lore.kernel.org/r/20221207205059.3848851-1-zenghuchen@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Pull i3c updates from Alexandre Belloni:
- support dynamic addition of i2c devices
* tag 'i3c/for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: fix uninitialized variable use in i2c setup
i3c: support dynamically added i2c devices
i3c: remove i2c board info from i2c_dev_desc
There is a regular need in the kernel to provide a way to declare
having a dynamically sized set of trailing elements in a structure.
Kernel code should always use “flexible array members”[1] for these
cases. The older style of one-element or zero-length arrays should
no longer be used[2].
This code was transformed with the help of Coccinelle:
(next-20220214$ spatch --jobs $(getconf _NPROCESSORS_ONLN) --sp-file script.cocci --include-headers --dir . > output.patch)
@@
identifier S, member, array;
type T1, T2;
@@
struct S {
...
T1 member;
T2 array[
- 0
];
};
UAPI and wireless changes were intentionally excluded from this patch
and will be sent out separately.
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.16/process/deprecated.html#zero-length-and-one-element-arrays
Link: https://github.com/KSPP/linux/issues/78
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
The driver core ignores the return value of struct bus_type::remove()
because there is only little that can be done. To simplify the quest to
make this function return void, let struct i3c_driver::remove() return
void, too. This makes it obvious that returning an error code is
a bad idea and future driver authors cannot get that wrong.
Up to now there are no drivers with a remove callback, so there is no
need to adapt drivers.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210128091048.17006-2-u.kleine-koenig@pengutronix.de
Adrian Hunter
Aman Kumar Pandey
Frank Li
Adrian Ng Ho Yin
Alexandre Belloni
Jarkko Nikula
Wolfram Sang
Arnd Bergmann
Billy Tsai
Carlos Song
Linus Torvalds
Bhoomik Gupta
Greg Kroah-Hartman
Randy Dunlap
Zbigniew Lukwinski
Jeremy Kerr
Matt Johnston
Uwe Kleine-König
Andy Shevchenko
Jack Chen
Naveen Krishna Chatradhi
Jamie Iles
Gustavo A. R. Silva