adt7470_pwm_read() currently ignores failures returned by
pwm1_freq_get(). If the register read fails, the negative error code is
returned through *val while the function itself reports success,
potentially exposing a negative PWM frequency through sysfs.
Fix this by using the cached PWM frequency maintained by the driver,
eliminating the register access from the read path.
Apart from the corrected error propagation and using the cached value,
no functional change is intended.
Fixes: ef67959c42 ("hwmon: (adt7470) Convert to use regmap")
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://lore.kernel.org/r/20260727-adt7470_fixes-v2-6-598e38a46ba6@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ADT7470_PWM3_AUTO_MASK and ADT7470_PWM4_AUTO_MASK macros are
currently defined with swapped bit values.
According to Table 22 of the ADT7470 datasheet, the Fan Control Mode
Configuration for register 0x69 follows the exact same bit position
layout as register 0x68:
- 0x68 Bit[7] corresponds to BHVR1 (PWM1) -> 0x80
- 0x68 Bit[6] corresponds to BHVR2 (PWM2) -> 0x40
- 0x69 Bit[7] corresponds to BHVR3 (PWM3) -> 0x80
- 0x69 Bit[6] corresponds to BHVR4 (PWM4) -> 0x40
Consequently, PWM3 should use mask 0x80 and PWM4 should use 0x40.
This typo did not cause any functional bugs because these specific
macros are never referenced in the driver code. Instead, the driver
correctly applies the configuration by relying on the modulo parity of
the channel index (e.g., `channel % 2`) to selectively apply either
ADT7470_PWM1_AUTO_MASK (0x80) or ADT7470_PWM2_AUTO_MASK (0x40).
Since the bit layout is identical between the two configuration
registers, the hardware is currently configured correctly.
Fix the macro definitions to reflect the datasheet accurately and
prevent future bugs or confusion during code review and refactoring.
As this is a purely cosmetic fix with no functional impact, a backport
to stable kernels is not necessary.
Fixes: 6f9703d0be ("hwmon: add support for adt7470")
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://lore.kernel.org/r/20260727-adt7470_fixes-v2-4-598e38a46ba6@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When userspace configures 'auto_update_interval' to 0 via sysfs, the
background kthread executes schedule_timeout_interruptible(0), which
returns immediately.
If 'num_temp_sensors' is concurrently or previously set to 0, the
msleep_interruptible() delay inside adt7470_read_temperatures() also
becomes 0. This combination forces the background thread into a tight,
unbounded busy-loop, hogging the CPU and flooding the I2C bus with a
continuous stream of transactions.
Fix this vulnerability by raising the lower limit of the clamp_val in
auto_update_interval_store() from 0 to 500 milliseconds. This guarantees
a reasonable minimum sleep window between sensor updates, protecting the
system from intentional or accidental I2C bus denial of service.
Reported-by: sashiko-bot@kernel.org
Closes: https://lore.kernel.org/r/20260716213252.EACA71F000E9@smtp.kernel.org
Fixes: 89fac11cb3 ("adt7470: make automatic fan control really work")
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://lore.kernel.org/r/20260727-adt7470_fixes-v2-3-598e38a46ba6@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
adt7470_temp_write() and adt7470_pwm_write() update the driver's
cached values (temp_min, temp_max, pwm_input, pwm_enable) before issuing
the corresponding regmap_write(), and never check whether the write
succeeded before committing that update. If the I2C transaction fails,
the function correctly propagates the error to the caller, but the cache
silently keeps the new value, which was never actually applied to the
hardware. Subsequent reads then report a value that does not match the
device state.
Reorder both write paths to update the cache only after a successful
regmap_write(), so the cache always reflects what was actually
written to the hardware.
Fixes: ef67959c42 ("hwmon: (adt7470) Convert to use regmap")
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://lore.kernel.org/r/20260727-adt7470_fixes-v2-2-598e38a46ba6@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
During adt7470_read_temperatures(), the driver temporarily switches
the PWM channels to manual mode, performs the temperature collection,
and then restores the original configuration registers.
However, if an I2C transaction fails at any point after entering manual
mode, the function aborts and returns immediately. This leaves the
configuration registers un-restored, permanently trapping the fans in
manual mode.
Introduce a recovery path to ensure that the original PWM configuration
registers are always restored, even when intermediate I2C operations
fail.
Reported-by: sashiko-bot@kernel.org
Closes: https://lore.kernel.org/r/20260716213252.EACA71F000E9@smtp.kernel.org
Fixes: ef67959c42 ("hwmon: (adt7470) Convert to use regmap")
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://lore.kernel.org/r/20260727-adt7470_fixes-v2-1-598e38a46ba6@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
cifs_file_set_size() calls cifs_setsize() on success, which calls
i_size_write(), updating i_size to the new value. The subsequent
check attrs->ia_size != i_size_read() in both cifs_setattr_unix()
and cifs_setattr_nounix() therefore always evaluates false after a
successful cifs_file_set_size(), making the smp_store_release() of
time_last_write dead code. The truncate path was unprotected against
stale readdir size updates.
Move the stamp to before the cifs_file_set_size() RPC call, guarded
by attrs->ia_size != i_size_read() to exclude no-op same-size
ftruncate(2) calls from stamping time_last_write unnecessarily.
On the error path the stamp remains rather than being restored:
restoring a stale snapshot (prev_tlw) could silently erase a
concurrent _cifsFileInfo_put() close stamp if that close arrived
between the READ_ONCE and the smp_store_release. readdir is
suppressed until the stamp expires, which extends beyond one acregmax
if the caller retries failed truncations. stat() is unaffected: the
cifs_revalidate_dentry_attr() path calls cifs_fattr_to_inode() with
from_readdir=false, which bypasses the time_last_write check in
is_size_safe_to_change() entirely and always writes the authoritative
QUERY_INFO result to i_size.
Remove the now-unreachable stamp from the dead block in both functions.
Fixes: e8a8d54c2d ("cifs: prevent readdir from changing file size due to stale directory metadata")
Signed-off-by: Frank Sorenson <sorenson@redhat.com>
Reviewed-by: Paulo Alcantara (Red Hat) <pc@manguebit.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
The time_last_write stamp was scattered across cifs_close(),
smb2_deferred_work_close(), and the three drain functions in misc.c.
This missed the case where background I/O holds the final reference
after userspace close() returns, and required explicit maintenance at
each close-path site.
Move the smp_store_release() into _cifsFileInfo_put(), immediately
before releasing open_file_lock. This single location covers all
close paths unconditionally: normal close, background I/O dropping the
final reference, deferred close via timer or external drain. The
spinlock's store-release/load-acquire pairing with is_inode_writable()
already provides the ordering guarantee documented in
is_size_safe_to_change().
Remove the now-redundant stamps from cifs_close(),
smb2_deferred_work_close(), and all six stamp sites in the misc.c
deferred-close drain functions.
Fixes: e8a8d54c2d ("cifs: prevent readdir from changing file size due to stale directory metadata")
Signed-off-by: Frank Sorenson <sorenson@redhat.com>
Reviewed-by: Paulo Alcantara (Red Hat) <pc@manguebit.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Lenovo Legion 7 15ASH11 with AMD RYZEN AI MAX+ 392 (Strix Halo, ACP
7.0) uses Realtek ALC287 series codec and no any DMIC connected by ACP.
All DMICs directly connet with ALC codec.
Without this quirk, Input Device of Gnome Sound settings shows Internal
Stereo Microphone and Digital Microphone by default. In fact, Digital
Microphone of ACP doesn't work due to no connecting with ALC287 codec,
the Internal Stereo Microphone as analog device based on snd_hda_intel
driver can work well.
Add a DMI quirk to override the flag to 0, consistent with the existing
entry for the Lenovo Yoga Pro 7 15ASH11.
Signed-off-by: Jackie Dong <xy-jackie@139.com>
Link: https://patch.msgid.link/20260727041452.16701-1-xy-jackie@139.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Avoid redundant 'strlen()' and use the convenient 'strreplace()'
to simplify 'cifs_fscache_get_super_cookie()'.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Steve French <stfrench@microsoft.com>
cv1800b_adc_volume_set() serves as the .put callback for the "Internal
I2S Capture Volume" control.
ALSA mixer control callbacks must return 1 when the register value is
modified, 0 if unchanged, or a negative error code on failure. Returning
0 unconditionally causes ALSA core to assume the value was unchanged,
suppressing SNDRV_CTL_EVENT_MASK_VALUE change notifications to userspace
sound servers (e.g. PipeWire/PulseAudio).
Fix this by comparing the new register value with the existing register
value. If unchanged, return 0; otherwise, write the updated value and
return 1.
Fixes: 4cf8752a03 ("ASoC: sophgo: add CV1800B internal ADC codec driver")
Signed-off-by: Surendra Singh Chouhan <kr494167@gmail.com>
Link: https://patch.msgid.link/20260727053804.25599-1-kr494167@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
sctp_assoc_add_peer() increments the association's 16-bit transport_count
for every new unique peer. Adding the 65,536th transport wraps the count to
zero.
SCTP sock_diag uses transport_count to reserve the INET_DIAG_PEERS payload,
then copies one sockaddr_storage for every entry in transport_addr_list.
After the wrap, a diagnostic dump reserves an empty payload and writes
8 MiB of peer addresses past the skb tail.
Reject a new unique peer when transport_count has reached U16_MAX. Perform
the check after the existing-peer lookup so a duplicate address continues
to return its existing transport at the limit.
Fixes: 8f840e47f1 ("sctp: add the sctp_diag.c file")
Cc: stable@vger.kernel.org
Signed-off-by: Asim Viladi Oglu Manizada <manizada@pm.me>
Acked-by: Xin Long <lucien.xin@gmail.com>
Link: https://patch.msgid.link/20260725032053.521705-1-manizada@pm.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
netfs_alloc_folioq_buffer() may leave a partially allocated folio
queue attached to the caller's buffer pointer when it returns an error.
smb3_init_transform_rq() stores the buffer in the request only after
allocation succeeds, so the common error path cannot free a partial
allocation. Store the buffer pointer before checking the return value so
err_free releases it.
Signed-off-by: Yichong Chen <chenyichong@uniontech.com>
Reviewed-by: ChenXiaoSong <chenxiaosong@kylinos.cn>
Signed-off-by: Steve French <stfrench@microsoft.com>
sctp_unpack_cookie() skips cookie expiration checks whenever an
association already exists. This is broader than the exception in
RFC 9260 Section 5.2.4.
For an existing association, Section 5.2.4 permits an expired State
Cookie only when both Verification Tags in the cookie match the current
association. Otherwise, the packet SHOULD be discarded and a Stale
Cookie ERROR MUST be sent.
The broad check lets an expired Action A restart cookie reach
sctp_sf_do_dupcook_a(). In a runtime test with the default 60 second
cookie lifetime, replaying such a cookie after 65 seconds returned a
COOKIE-ACK and restarted the association.
Check cookie expiration unless both Verification Tags match. This
preserves the Action D exception for a lost COOKIE ACK while rejecting
expired cookies in all other cases.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Yuxiang Yang <yangyx22@mails.tsinghua.edu.cn>
Acked-by: Xin Long <lucien.xin@gmail.com>
Link: https://patch.msgid.link/20260723225623.2658868-1-yangyx22@mails.tsinghua.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
br_multicast_leave_group() iterates mp->ports with pp = &p->next in
its fast-leave path. After br_multicast_del_pg() removes p,
continuing the loop advances pp through the deleted entry.
If multicast-to-unicast was enabled, the bridge can hold multiple port
groups for the same port and group with different source MAC
addresses. Once multicast-to-unicast is disabled,
br_port_group_equal() matches those entries by port only. A fast leave
can then delete one entry and continue from its stale next pointer,
leaving mp->ports pointing at a deleted port group.
Fast leave only needs to remove one matching port group. Break after
br_multicast_del_pg() so the loop stops before dereferencing the
removed entry.
Fixes: 6db6f0eae6 ("bridge: multicast to unicast")
Cc: stable@vger.kernel.org
Reported-by: Vega <vega@nebusec.ai>
Signed-off-by: Zhiling Zou <zhilinz@nebusec.ai>
Signed-off-by: Ren Wei <enjou1224z@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/1cf0898872ef7c72d5f4c0304414a192c6dac591.1784707712.git.zhilinz@nebusec.ai
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
fib6_rule_suppress() drops a suppressed route with ip6_rt_put_flags(),
but leaves res->rt6 pointing at the released rt6_info.
If no later rule supplies a replacement, fib6_rule_lookup() still sees
res.rt6 and returns that stale dst to its caller. A suppressing rule can
therefore leak a released route back to rt6_lookup(), and the next put
hits rcuref_put_slowpath() from dst_release().
Clear res->rt6 when suppressing the route so suppressed lookups fall
through to the null dst instead of reusing the released one.
Fixes: cdef485217 ("ipv6: fix memory leak in fib6_rule_suppress")
Cc: stable@vger.kernel.org
Reported-by: Vega <vega@nebusec.ai>
Signed-off-by: Zhiling Zou <zhilinz@nebusec.ai>
Signed-off-by: Ren Wei <enjou1224z@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/4b8acb7787d54e440155585dd32ebdf0bef7d122.1784710966.git.zhilinz@nebusec.ai
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
TIPC socket tracepoints dump queue state through tipc_sk_dump(). Most
queue-dump callsites already serialize that walk under the socket lock or
sk->sk_lock.slock, but tipc_poll() calls trace_tipc_sk_poll(...,
TIPC_DUMP_ALL, ...) without holding either lock.
That lets the poll trace path reach tipc_list_dump() and backlog head/tail
dumping while another context dequeues and frees an skb, leaving the trace
helper dereferencing a stale queue entry.
Stop the unlocked poll trace site from requesting queue dumps. Other queue
dump trace callsites keep their existing output under the locking they
already provide, while poll still emits the event itself without walking
live queue members from an unlocked context.
Fixes: b4b9771bcb ("tipc: enable tracepoints in tipc")
Cc: stable@vger.kernel.org
Reported-by: Vega <vega@nebusec.ai>
Signed-off-by: Zihan Xi <zihanx@nebusec.ai>
Signed-off-by: Ren Wei <enjou1224z@gmail.com>
Reviewed-by: Tung Nguyen <tung.quang.nguyen@est.tech>
Link: https://patch.msgid.link/f8119abd5e5ecc400597de667ae9d39656de56d0.1784794294.git.zihanx@nebusec.ai
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet says:
====================
vxlan: fixes for skb header pulling, cloning, and concurrency in TX path
While working on RTNL-less fill_info for vxlan, Sashiko found annoying
pre-existing issues, adding noise to an already complex work.
This series addresses some of them in VXLAN transmit path,
primarily within route_shortcircuit(), header validation, and neighbour
lookup.
Patch 1 fixes a potential use-after-free in vxlan_xmit() caused by caching
the Ethernet header pointer ('eth') before calling route_shortcircuit(),
which can reallocate skb->head via pskb_may_pull().
Patch 2 calls skb_cow_head() in route_shortcircuit() before modifying the
Ethernet header in-place, preventing packet header corruption when the skb
is cloned (e.g., by packet sockets, tcpdump, or dev_queue_xmit).
Patch 3 replaces direct reads of n->ha in route_shortcircuit() with
neigh_ha_snapshot() to safely snapshot the neighbour hardware address
under seqlock protection, avoiding potential torn reads during
asynchronous updates.
Patch 4 changes route_shortcircuit() to use pskb_network_may_pull() instead
of pskb_may_pull(). Since skb->data points to the MAC header on transmit
(skb_network_offset(skb) == ETH_HLEN), pskb_may_pull() was only checking
6 bytes into the IP header, leaving the remainder un-pulled in non-linear
frags.
Patch 5 applies pskb_network_may_pull() to the remaining transmit-path
header pull checks in arp_reduce(), ND solicitation proxy checks, and
MDB entry lookup, where skb->data similarly points to the Ethernet header.
====================
Link: https://patch.msgid.link/20260723144249.759100-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In vxlan_xmit(), arp_reduce(), and vxlan_mdb_entry_skb_get(), pskb_may_pull() was
being called to verify the availability of network layer headers (ARP, IPv6/ND,
IP/IPv6 MDB keys).
However, during transmit skb->data points to the MAC header, so skb_network_offset(skb)
is ETH_HLEN (14 bytes). Using pskb_may_pull(skb, len) only checks len bytes from skb->data
rather than skb_network_offset(skb) + len, which can leave part of the network header
in non-linear frags.
Replace these remaining pskb_may_pull() calls with pskb_network_may_pull() to properly
account for the MAC header offset.
Fixes: e4f67addf1 ("add DOVE extensions for VXLAN")
Fixes: f564f45c45 ("vxlan: add ipv6 proxy support")
Fixes: 0f83e69f44 ("vxlan: Add MDB data path support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: stable@vger.kernel.org
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260723144249.759100-6-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
route_shortcircuit() currently calls pskb_may_pull(skb, sizeof(struct iphdr))
(or ipv6hdr), which checks if bytes are available starting from skb->data.
However, in vxlan_xmit(), skb->data points to the MAC header, so
skb_network_offset(skb) is ETH_HLEN (14 bytes). Using pskb_may_pull(skb, 20)
only checks 20 bytes from skb->data (which is 14 bytes MAC header + 6 bytes of
IP header), leaving the rest of the IP header potentially un-pulled in non-linear
frags. Subsequent dereferences of ip_hdr(skb)->daddr can read beyond the pulled
linear buffer length.
Fix this by using pskb_network_may_pull(), which adds skb_network_offset(skb) to
the length check to ensure the full network header is present in the linear buffer.
Fixes: e4f67addf1 ("add DOVE extensions for VXLAN")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20260723144249.759100-5-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The neighbour hardware address n->ha can be updated asynchronously by the
neighbour subsystem, protected by n->ha_lock seqlock. Reading n->ha without
holding the seqlock loop can lead to torn reads or reading a partially updated
MAC address.
Use neigh_ha_snapshot() in route_shortcircuit() to safely copy n->ha under
read_seqbegin()/read_seqretry() lock protection before using it.
Note that arp_reduce() and neigh_reduce() seem to have the same issue
left for future patches.
Fixes: e4f67addf1 ("add DOVE extensions for VXLAN")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20260723144249.759100-4-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When route_shortcircuit() performs L3 short-circuit routing, it modifies
the Ethernet header of the skb in-place:
memcpy(eth_hdr(skb)->h_source, eth_hdr(skb)->h_dest, dev->addr_len);
memcpy(eth_hdr(skb)->h_dest, n->ha, dev->addr_len);
If the incoming skb is cloned (for example by packet sockets, tcpdump, or
dev_queue_xmit), modifying the Ethernet header without uncloning can corrupt
the packet header for other readers holding a reference to the cloned skb.
Ensure the skb header is writable and unshared by calling skb_cow_head(skb, 0)
prior to updating the Ethernet header. If skb_cow_head() fails, abort short-circuiting
and return false to allow standard packet processing fallback.
Fixes: e4f67addf1 ("add DOVE extensions for VXLAN")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260723144249.759100-3-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before route_shortcircuit(), the eth header pointer is cached from eth_hdr(skb).
Inside route_shortcircuit(), pskb_may_pull() can be called, which may
reallocate skb->head.
In this case, returning to vxlan_xmit() leaves the cached eth pointer pointing to
freed memory, leading to a use-after-free when dereferencing eth->h_dest.
Fix this by updating eth = eth_hdr(skb) after calling route_shortcircuit().
Fixes: ae88408256 ("VXLAN: Allow L2 redirection with L3 switching")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20260723144249.759100-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sashiko reports:
During initialization of the nct6116 chip, the driver sets data->pwm_num
to 5. However, it assigns several NCT6106 register arrays (such as
NCT6106_REG_WEIGHT_DUTY_STEP, NCT6106_REG_WEIGHT_TEMP_SEL, and
NCT6106_REG_WEIGHT_TEMP_*) to data->REG_PWM and data->REG_WEIGHT_TEMP.
These arrays only contain 3 elements.
In nct6775_update_pwm(), the driver iterates up to data->pwm_num. If
data->has_pwm has bits 3 or 4 set (which is structurally possible for
nct6116), the loop attempts to read elements at index 3 and 4 from these
3-element arrays. This results in a global out-of-bounds read, which can
be caught by KASAN.
Furthermore, the driver uses these garbage out-of-bounds values as
hardware register addresses for subsequent read and write operations. This
leads to invalid hardware register access, potentially causing hardware
misconfiguration or system crashes.
The underlying problem is that the chip does support up to five fan
control channels, but only the first three support weight control.
Fix the problem by extending the affected weight register arrays with
zeroed fields. The driver uses zeroed register addresses to determine
if a register is supported or not, and skips accesses for unsupported
registers.
Reported-by: Sashiko <sashiko-bot@kernel.org>
Fixes: 29c7cb485b ("hwmon: (nct6775) Integrate new model nct6116")
Cc: Björn Gerhart <gerhart@posteo.de>
Cc: Florian Bezdeka <florian.bezdeka@siemens.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull misc fixes from Andrew Morton:
"13 hotfixes. All are cc:stable. 11 are for MM. All are singletons -
please see the changelogs for details"
* tag 'mm-hotfixes-stable-2026-07-27-14-18' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
fs/proc/task_mmu: fix PAGEMAP_SCAN written state for PMD holes
mm/hugetlb: fix list corruption in allocate_file_region_entries()
mm: mglru: fix stale batch updates after memcg reparenting
selftest: fix headers in fclog.c
ocfs2: fix boundary check in ocfs2_check_dir_entry() to use buffer offset
mm/percpu-km: fix bitmap overflow and accounting in pcpu_create_chunk()
mm/util: don't read __page_2 for order-1 folios in snapshot_page()
mm/hugetlb: fix swap entry corruption when clearing uffd-wp at fork()
mm: migrate_device: fix pte_pfn/pte_dirty called on non-present PTE
fs/proc/task_mmu: fix PAGEMAP_SCAN written state for unpopulated ptes
userfaultfd: wait on source PMD during UFFDIO_MOVE
lib: test_hmm: use device devt for coherent device range selection
mm/vmstat: fold stranded per-cpu node stats when a node comes online
Sashiko is concerned that reading a PWM frequency multiplier outside
the supported range of [1, 31] might result in bad PWM values written
to the chip. Technically, the chip should never return a value with
the upper 3 bits set, so this should never happen. However, it is
unknown if there are LM63 variants where the upper bits of the register
can be written.
Mask the register value read from the chip to only accept the lower 5 bit
when reading it from the chip to avoid the problem.
Reported-by: Sashiko <sashiko-bot@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull keys fixes from Jarkko Sakkinen:
- An unprivileged keyring whose keys collide through the
description-chunk path can drive assoc_array node splitting
into an out-of-bounds slot write. Fix it.
- Fix the DCP trusted keys backend
* tag 'for-next-keys-7.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd:
assoc_array: trim the final shortcut word using the current chunk end
keys: make keyring key-chunk byte order agree with keyring_diff_objects()
keys: fix out-of-bounds read in keyring_get_key_chunk()
KEYS: trusted: dcp: fix key_len validation and calc_blob_len() return type
Fix a severe AB/BA deadlock between the Common Clock Framework (CCF)
and the I2C adapter lock, which triggers when an I2C-controlled clock
generator client (like the Si5351) is registered or modified under the CCF.
During an i2c client clock (generator) frequency change, the CCF acquires its global
'prepare_lock' mutex and the driver calls i2c_transfer() to update the client's
chip registers, stalling for the adapter's I2C bus lock.
Concurrently, an independent, parallel transfer on the same bus (e.g., a GPIO
expander handling LEDs) can hold the I2C adapter lock. Inside this parallel
transfer path, jz4780_i2c_set_speed() calls clk_get_rate() on the host
controller's input clock to calculate bus timings. This call attempts to acquire
the blocked CCF 'prepare_lock', creating a circular dependency that freezes
the system.
The jz4780 host controller clock itself is static and never changes at runtime.
However, calling clk_get_rate() inside the active transfer path introduces
an unnecessary dependency on the CCF internal locks.
Eliminate this synchronous clk_get_rate() call from the active transfer
path by caching the static host peripheral clock rate once - inside the private
jz4780_i2c structure during jz4780_i2c_probe(). Update jz4780_i2c_set_speed()
to use this cached value, safely decoupling active I2C transactions from the
CCF internal locks without any risk of stale timings.
Assisted-by web based Google AI (pinpointing the bug and writing the message).
Fixes: ba92222ed6 ("i2c: jz4780: Add i2c bus controller driver for Ingenic JZ4780")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: <stable@vger.kernel.org> # v4.1+
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/2db6fd233aceb7238474e4833f4d25ca681c3ffb.1784492382.git.hns@goldelico.com
When inet_getpeer_v4() or inet_getpeer_v6() fails to allocate a peer entry
under memory pressure or tree size caps, redirect handlers previously fell
back to sending un-rate-limited ICMP/NDISC Redirect messages.
In IPv4, ip_rt_send_redirect() called icmp_send() directly when peer == NULL.
In IPv6, ip6_forward() and ndisc_send_redirect() passed a NULL peer into
inet_peer_xrlim_allow(), which returned true when peer == NULL.
Because ICMP/NDISC Redirects are not part of the default global rate limit
mask (sysctl_icmp_ratemask), sending redirects when peer == NULL creates
an un-rate-limited ICMP packet storm.
Fix this by failing closed in ip_rt_send_redirect(), ip6_forward(), and
ndisc_send_redirect() when peer is NULL.
Fixes: 92d8682926 ("inetpeer: Move ICMP rate limiting state into inet_peer entries.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260724072901.1633601-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
amd_mp2_register_cb() stores the platform I2C context in the MP2 PCI
driver's callback table before the adapter is registered. If
i2c_add_adapter() fails, probe returns and devres frees the context,
but the PCI driver can still dereference the stale pointer from its IRQ
and system-sleep callbacks.
Unregister the callback before returning the adapter registration error.
Fixes: 529766e0a0 ("i2c: Add drivers for the AMD PCIe MP2 I2C controller")
Co-developed-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Myeonghun Pak <mhun512@gmail.com>
Cc: <stable@vger.kernel.org> # v5.2+
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260721144147.31150-1-mhun512@gmail.com
spacemit_i2c_probe() requests the IRQ before it enables the clocks, resets
the controller and runs init_completion(). If an interrupt is already
pending, the handler runs too early: it reads registers while the clocks
are still off and calls complete() on an uninitialized completion. Request
the IRQ after the controller and completion are initialized, but still
before the adapter is registered.
Fixes: 5ea558473f ("i2c: spacemit: add support for SpacemiT K1 SoC")
Signed-off-by: Linmao Li <lilinmao@kylinos.cn>
Cc: <stable@vger.kernel.org> # v6.15+
Reviewed-by: Troy Mitchell <troy.mitchell@linux.spacemit.com>
Reviewed-by: Alex Elder <elder@riscstar.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260723021140.2293844-1-lilinmao@kylinos.cn
Sashiko reports:
When send_output_report() calls hid_hw_output_report(), the underlying USB
HID core calls usb_interrupt_msg() which maps this buffer directly for DMA.
When the DMA mapping flushes or invalidates the cacheline, it will corrupt
the adjacent variables (mutex, update_interval) that were modified
concurrently by the CPU. This causes memory corruption due to cacheline
sharing on non-coherent CPU architectures (such as ARM or MIPS). The DMA
API debugging tool (CONFIG_DMA_API_DEBUG) will trigger runtime warnings
for this violation.
Any operation that triggers send_output_report() (like setting a fan speed
or updating the interval) causes the USB DMA mapping. On systems with
non-coherent caches, this structural bug causes immediate and deterministic
memory corruption.
Align the output buffer to ARCH_DMA_MINALIGN to fix the problem.
Reported-by: Sashiko <sashiko-bot@kernel.org>
Fixes: 53e68c20ae ("hwmon: add driver for NZXT RGB&Fan Controller/Smart Device v2.")
Cc: Aleksandr Mezin <mezin.alexander@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Userspace can read sysfs attributes before driver registration is complete,
immediately after devm_hwmon_device_register_with_info() has been called.
At that time, data->hwmon_dev is not yet initialized. This can trigger
a NULL pointer access since lm90_update_device() and with it
lm90_update_alarms_locked() will be called. This call schedules
report_work and lm90_report_alarms(), which passes the still-NULL
data->hwmon_dev to hwmon_notify_event() and triggers a NULL pointer
dereference.
Fix the problem by only scheduling the report and alert workers
data->hwmon_dev is set.
Reported-by: Sashiko <sashiko-bot@kernel.org>
Fixes: f6d0775119 ("hwmon: (lm90) Rework alarm/status handling")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Sashiko reports:
In sht3x_update_client(), the 16-bit temperature and humidity values are
extracted from a stack-allocated byte array using be16_to_cpup(). The
pointers passed to this function are calculated as buf and buf + 3. Since
the difference between the two pointers is an odd number of bytes, at
least one of them is guaranteed to be at an unaligned offset.
This will trigger an alignment fault on strict-alignment architectures
such as ARMv5 or SPARC, resulting in a kernel panic.
Fix the problem by using get_unaligned_be16() instead of be16_to_cpup(),
and put_unaligned_be16() instead of cpu_to_be16().
Fixes: 7c84f7f80d ("hwmon: add support for Sensirion SHT3x sensors")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Coverity reports an out-of-bounds access when reading the minimum alarm
voltage for the VGPIO channel. Add the missing return statement to fix
the problem.
Fixes: cbc29538db ("hwmon: Add driver for LTC4282")
Cc: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Sashiko reports several integer overflow problems in the ina2xx driver
caused by unbounded multiplications and inadequate types for intermediate
calculations.
Specifically:
- In ina2xx_get_value(), the return type is changed from int to long.
Intermediate calculations for current are now performed using 64-bit
types to prevent 32-bit integer overflow before the division by 1000.
- When calculating power in ina2xx_get_value() and
sy24655_average_power_read(), interim values are cast to u64 and clamped
to LONG_MAX. This prevents overflow when regval or accumulator_24 is
multiplied by power_lsb_uW.
- In ina226_alert_to_reg(), the clamping logic is rewritten using min_t().
This safely avoids integer overflows when scaling user-provided values
for shunt voltage, bus voltage, power, and current limits.
Cc: Loic Poulain <loic.poulain@oss.qualcomm.com>
Fixes: ab7fbee452 ("hwmon: (ina2xx) Fix various overflow issues")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pmbus_notify() calls sysfs_notify() and kobject_uevent() on the i2c
client's kobject, but the alarm attributes live on the hwmon class
device registered by pmbus_do_probe(). Notifying the parent i2c device
is a no-op for both poll(POLLPRI) waiters and udev listeners: the named
attribute does not exist on that kobject.
Notify the hwmon device instead, so poll() wakes up and "change"
uevents fire on the inX_alarm/tempX_alarm attributes when SMBALERT#
reports a fault.
Fixes: f469bde9af ("hwmon: (pmbus/core) Notify hwmon events")
Cc: stable@vger.kernel.org # v6.4+
Signed-off-by: Vincent Jardin <vjardin@free.fr>
Link: https://lore.kernel.org/r/20260723-fix_hwmon_notify_v1-v1-1-5a24c528686d@free.fr
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Unlike NCT6106, NCT6116 only has three temperature registers, and with
it only three temperature source and temperature source configuration
registers. The register addresses match those of NCT6106 and can be
re-used.
The code used a separate array to list the temperature source registers
for NCT6116, but used the size of the NCT6106 register array to set
the number of registers. The NCT6106 register array provides six addresses,
while the temperature source register array for NCT6116 only provides three
addresses. This causes a KASAN report.
BUG: KASAN: global-out-of-bounds in nct6775_probe+0x936/0x46f0 [nct6775]
Read of size 2 at addr ffffffffc19561a6 by task modprobe/954
...
Call Trace:
dump_stack+0x7d/0xa7
print_address_description.constprop.0+0x1c/0x220
? __kasan_kmalloc.constprop.0+0xc9/0xd0
? __kmalloc_node_track_caller+0x194/0x5b0
? nct6775_probe+0x936/0x46f0 [nct6775]
? nct6775_probe+0x936/0x46f0 [nct6775]
...
Fix the problem by hard-coding the number of temperature and temperature
configuration registers to three for NCT6116. Drop the unnecessary
NCT6116_REG_TEMP_SOURCE array and re-use NCT6106_REG_TEMP_SOURCE.
Reported-by: Florian Bezdeka <florian.bezdeka@siemens.com>
Closes: https://lore.kernel.org/linux-hwmon/57cfc3fa-d4e9-4c10-8aa7-4ad0af7ebebe@roeck-us.net/T/#t
Fixes: 29c7cb485b ("hwmon: (nct6775) Integrate new model nct6116")
Cc: Björn Gerhart <gerhart@posteo.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
SPI host transfers could intermittently stall with spi_transfer timeouts.
The TXFULL condition was checked only once in cdns_transfer_one() before
cdns_spi_process_fifo(), so if the FIFO became full again during refill,
writes could be dropped and the transfer would never complete.
Move the TXFULL busy-wait into the TX path of cdns_spi_process_fifo() so
the 10µs back-off is applied per FIFO entry during filling, ensuring
forward progress and eliminating spurious timeouts.
Restrict the delay to host mode using spi_controller_is_target(), the
controller is passed into cdns_spi_process_fifo() so the check is made at
the point of use. In target mode this delay must not run as it causes the
target to miss its transfer window and corrupt data.
Fixes: 49530e6411 ("spi: cadence: Add usleep_range() for cdns_spi_fill_tx_fifo()")
Signed-off-by: Srikanth Boyapally <srikanth.boyapally@amd.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://patch.msgid.link/20260720125510.60166-1-srikanth.boyapally@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SINEGAIN2_REG case in cali_reg_update() references t->sin_gn[]
rather than t->sin_gn2[], causing the second pilot tone gain
calibration to be programmed with the wrong register address.
These are distinct fields in struct fct_param_address and are
populated from separate firmware parameters by the parser in
tas2781-fmwlib.c.
Fixes: 84d6a465f2 ("ASoC: tas2781: Support dsp firmware Alpha and Beta seaies")
Signed-off-by: wangdicheng <wangdicheng@kylinos.cn>
Link: https://patch.msgid.link/20260720081616.631413-1-wangdich9700@163.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Charles Keepax <ckeepax@opensource.cirrus.com> says:
Currently there exists a couple races that can result in the DAPM graph
coming up in a state that doesn't match the hardware with respect to
SDCA jack detection. This series fixes these up by adding a component
level fixup_controls helper into the asoc core and shuffling around the
IRQ requests from the SDCA side.
The core creates DAPM widgets/routes quite a long time before
it creates the associated ALSA control, and the jack detection
IRQ is currently registered in component probe. At the time of
component probe, the DAPM widgets exist, shortly after this the
DAPM routes are added. At the time the DAPM routes are added the
register value for the control is checked and the appropriate path
is connected. The existing handling in the SDCA jack IRQ handles
the case the control doesn't exist and updates the registers
directly, which works until the DAPM routes are added. After the
routes are added the DAPM graph has already set connected on a
particular DAPM path, which will not be updated until an IRQ is
received when the control is present. Thus those updates are
usually not reflected in the resulting DAPM graph which can lead
to the audio path being erroneously powered on/off.
Link: https://patch.msgid.link/20260721143636.361814-1-ckeepax@opensource.cirrus.com
Now that the IRQs are always registered after all the ALSA
controls are created it is possible to search for the control
at the point the IRQ is requested. Move the control search out
of the IRQ handler and do it at IRQ request time.
This also fixes a potential issue when the card was torn down
and reprobed without destroying the codec device, the kctl
pointer stored by the IRQ handler would not be updated to the
new control on the second probe.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20260721143636.361814-8-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently there are some race conditions around the boot of SDCA
jack detection. The core creates DAPM widgets/routes quite a
long time before it creates the associated ALSA control, and
the jack detection IRQ is currently registered in component
probe. At the time of component probe, the DAPM widgets exist,
shortly after this the DAPM routes are added. At the time the DAPM
routes are added the register value for the control is checked
and the appropriate path is connected. The existing handling
in the SDCA jack IRQ handles the case the control doesn't exist
and updates the registers directly, which works until the DAPM
routes are added. After the routes are added the DAPM graph has
already set connected on a particular DAPM path, which will not
be updated until an IRQ is received when the control is present.
Thus those updates are usually not reflected in the resulting
DAPM graph which can lead to the audio path being erroneously
powered on/off.
Switch to the new fixup_controls callback to register the
IRQs, this is guaranteed to run after all the controls have
been created. Which means we can avoid the aforementioned race
condition and as a bonus no longer need to concern ourselves
with a case where the IRQ handler runs and the ALSA control
is unavailable.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20260721143636.361814-7-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A card level fixup_controls callback was added in:
commit df4d27b19b ("ASoC: Introduce 'fixup_controls' card method")
This allowed the machine driver to take actions after all the
card controls have been added. However, there are times when a
codec driver would also want to do things like obtain references
to controls for later use, which require all the controls to be
present. Add a component level fixup_controls callback, echoing
the card level option.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20260721143636.361814-6-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, the IRQ data (attached Entity/Control/etc) is populated
as the IRQ is requested. However, this can cause issues as
occasionally the setup process wants to access specifics of
an IRQ before the IRQ is actually enabled. To facilitate this
cache all the IRQ data during sdca_irq_populate_early() and make
sdca_irq_populate() simply request the outstanding IRQs. This
also has the advantage that sdca_irq_populate() can now just
iterate through the IRQ array which is much smaller/faster than
going through every Entity in the Function for Controls.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20260721143636.361814-5-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Luiz Angelo Daros de Luca
Chenguang Zhao
Frank Sorenson
Jackie Dong
Dmitry Antipov
Surendra Singh Chouhan
David Corvaglia
Asim Viladi Oglu Manizada
Yichong Chen
Yuxiang Yang
Zhiling Zou
Zihan Xi
Jakub Kicinski
Eric Dumazet
Guenter Roeck
Linus Torvalds
H. Nikolaus Schaller
Myeonghun Pak
Linmao Li
Maarten Lankhorst
Vincent Jardin
Srikanth Boyapally
wangdicheng
Mark Brown
Charles Keepax