[ Upstream commit d4bac0288a ]
Classic BPF socket filters with SKB_NET_OFF and SKB_LL_OFF fail to
read when these offsets extend into frags.
This has been observed with iwlwifi and reproduced with tun with
IFF_NAPI_FRAGS. The below straightforward socket filter on UDP port,
applied to a RAW socket, will silently miss matching packets.
const int offset_proto = offsetof(struct ip6_hdr, ip6_nxt);
const int offset_dport = sizeof(struct ip6_hdr) + offsetof(struct udphdr, dest);
struct sock_filter filter_code[] = {
BPF_STMT(BPF_LD + BPF_B + BPF_ABS, SKF_AD_OFF + SKF_AD_PKTTYPE),
BPF_JUMP(BPF_JMP + BPF_JEQ + BPF_K, PACKET_HOST, 0, 4),
BPF_STMT(BPF_LD + BPF_B + BPF_ABS, SKF_NET_OFF + offset_proto),
BPF_JUMP(BPF_JMP + BPF_JEQ + BPF_K, IPPROTO_UDP, 0, 2),
BPF_STMT(BPF_LD + BPF_H + BPF_ABS, SKF_NET_OFF + offset_dport),
This is unexpected behavior. Socket filter programs should be
consistent regardless of environment. Silent misses are
particularly concerning as hard to detect.
Use skb_copy_bits for offsets outside linear, same as done for
non-SKF_(LL|NET) offsets.
Offset is always positive after subtracting the reference threshold
SKB_(LL|NET)_OFF, so is always >= skb_(mac|network)_offset. The sum of
the two is an offset against skb->data, and may be negative, but it
cannot point before skb->head, as skb_(mac|network)_offset would too.
This appears to go back to when frag support was introduced to
sk_run_filter in linux-2.4.4, before the introduction of git.
The amount of code change and 8/16/32 bit duplication are unfortunate.
But any attempt I made to be smarter saved very few LoC while
complicating the code.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Link: https://lore.kernel.org/netdev/20250122200402.3461154-1-maze@google.com/
Link: https://elixir.bootlin.com/linux/2.4.4/source/net/core/filter.c#L244
Reported-by: Matt Moeller <moeller.matt@gmail.com>
Co-developed-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://lore.kernel.org/r/20250408132833.195491-2-willemdebruijn.kernel@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43130d02ba ]
We noticed the kworker in page_pool_release_retry() was waken
up repeatedly and infinitely in production because of the
buggy driver causing the inflight less than 0 and warning
us in page_pool_inflight()[1].
Since the inflight value goes negative, it means we should
not expect the whole page_pool to get back to work normally.
This patch mitigates the adverse effect by not rescheduling
the kworker when detecting the inflight negative in
page_pool_release_retry().
[1]
[Mon Feb 10 20:36:11 2025] ------------[ cut here ]------------
[Mon Feb 10 20:36:11 2025] Negative(-51446) inflight packet-pages
...
[Mon Feb 10 20:36:11 2025] Call Trace:
[Mon Feb 10 20:36:11 2025] page_pool_release_retry+0x23/0x70
[Mon Feb 10 20:36:11 2025] process_one_work+0x1b1/0x370
[Mon Feb 10 20:36:11 2025] worker_thread+0x37/0x3a0
[Mon Feb 10 20:36:11 2025] kthread+0x11a/0x140
[Mon Feb 10 20:36:11 2025] ? process_one_work+0x370/0x370
[Mon Feb 10 20:36:11 2025] ? __kthread_cancel_work+0x40/0x40
[Mon Feb 10 20:36:11 2025] ret_from_fork+0x35/0x40
[Mon Feb 10 20:36:11 2025] ---[ end trace ebffe800f33e7e34 ]---
Note: before this patch, the above calltrace would flood the
dmesg due to repeated reschedule of release_dw kworker.
Signed-off-by: Jason Xing <kerneljasonxing@gmail.com>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Link: https://patch.msgid.link/20250214064250.85987-1-kerneljasonxing@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a0a3ff659 ]
Upstream fix ac888d5886 ("net: do not delay dst_entries_add() in
dst_release()") moved decrementing the dst count from dst_destroy to
dst_release to avoid accessing already freed data in case of netns
dismantle. However in case CONFIG_DST_CACHE is enabled and OvS+tunnels
are used, this fix is incomplete as the same issue will be seen for
cached dsts:
Unable to handle kernel paging request at virtual address ffff5aabf6b5c000
Call trace:
percpu_counter_add_batch+0x3c/0x160 (P)
dst_release+0xec/0x108
dst_cache_destroy+0x68/0xd8
dst_destroy+0x13c/0x168
dst_destroy_rcu+0x1c/0xb0
rcu_do_batch+0x18c/0x7d0
rcu_core+0x174/0x378
rcu_core_si+0x18/0x30
Fix this by invalidating the cache, and thus decrementing cached dst
counters, in dst_release too.
Fixes: d71785ffc7 ("net: add dst_cache to ovs vxlan lwtunnel")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Link: https://patch.msgid.link/20250326173634.31096-1-atenart@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90a7138619 ]
Previous commit 8b5c171bb3 ("neigh: new unresolved queue limits")
introduces new netlink attribute NDTPA_QUEUE_LENBYTES to represent
approximative value for deprecated QUEUE_LEN. However, it forgot to add
the associated nla_policy in nl_ntbl_parm_policy array. Fix it with one
simple NLA_U32 type policy.
Fixes: 8b5c171bb3 ("neigh: new unresolved queue limits")
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Link: https://patch.msgid.link/20250315165113.37600-1-linma@zju.edu.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 986ffb3a57 ]
This patch acts as a parachute, catch all solution, by detecting
recursion loops in lwtunnel users and taking care of them (e.g., a loop
between routes, a loop within the same route, etc). In general, such
loops are the consequence of pathological configurations. Each lwtunnel
user is still free to catch such loops early and do whatever they want
with them. It will be the case in a separate patch for, e.g., seg6 and
seg6_local, in order to provide drop reasons and update statistics.
Another example of a lwtunnel user taking care of loops is ioam6, which
has valid use cases that include loops (e.g., inline mode), and which is
addressed by the next patch in this series. Overall, this patch acts as
a last resort to catch loops and drop packets, since we don't want to
leak something unintentionally because of a pathological configuration
in lwtunnels.
The solution in this patch reuses dev_xmit_recursion(),
dev_xmit_recursion_inc(), and dev_xmit_recursion_dec(), which seems fine
considering the context.
Closes: https://lore.kernel.org/netdev/2bc9e2079e864a9290561894d2a602d6@akamai.com/
Closes: https://lore.kernel.org/netdev/Z7NKYMY7fJT5cYWu@shredder/
Fixes: ffce41962e ("lwtunnel: support dst output redirect function")
Fixes: 2536862311 ("lwt: Add support to redirect dst.input")
Fixes: 14972cbd34 ("net: lwtunnel: Handle fragmentation")
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Link: https://patch.msgid.link/20250314120048.12569-2-justin.iurman@uliege.be
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77e45145e3 ]
napi_schedule() is expected to be called either:
* From an interrupt, where raised softirqs are handled on IRQ exit
* From a softirq disabled section, where raised softirqs are handled on
the next call to local_bh_enable().
* From a softirq handler, where raised softirqs are handled on the next
round in do_softirq(), or further deferred to a dedicated kthread.
Other bare tasks context may end up ignoring the raised NET_RX vector
until the next random softirq handling opportunity, which may not
happen before a while if the CPU goes idle afterwards with the tick
stopped.
Such "misuses" have been detected on several places thanks to messages
of the kind:
"NOHZ tick-stop error: local softirq work is pending, handler #08!!!"
For example:
__raise_softirq_irqoff
__napi_schedule
rtl8152_runtime_resume.isra.0
rtl8152_resume
usb_resume_interface.isra.0
usb_resume_both
__rpm_callback
rpm_callback
rpm_resume
__pm_runtime_resume
usb_autoresume_device
usb_remote_wakeup
hub_event
process_one_work
worker_thread
kthread
ret_from_fork
ret_from_fork_asm
And also:
* drivers/net/usb/r8152.c::rtl_work_func_t
* drivers/net/netdevsim/netdev.c::nsim_start_xmit
There is a long history of issues of this kind:
019edd01d1 ("ath10k: sdio: Add missing BH locking around napi_schdule()")
3300685893 ("idpf: disable local BH when scheduling napi for marker packets")
e3d5d70cb4 ("net: lan78xx: fix "softirq work is pending" error")
e55c27ed9c ("mt76: mt7615: add missing bh-disable around rx napi schedule")
c0182aa985 ("mt76: mt7915: add missing bh-disable around tx napi enable/schedule")
970be1dff2 ("mt76: disable BH around napi_schedule() calls")
019edd01d1 ("ath10k: sdio: Add missing BH locking around napi_schdule()")
30bfec4fec ("can: rx-offload: can_rx_offload_threaded_irq_finish(): add new function to be called from threaded interrupt")
e63052a5dd ("mlx5e: add add missing BH locking around napi_schdule()")
83a0c6e589 ("i40e: Invoke softirqs after napi_reschedule")
bd4ce941c8 ("mlx4: Invoke softirqs after napi_reschedule")
8cf699ec84 ("mlx4: do not call napi_schedule() without care")
ec13ee8014 ("virtio_net: invoke softirqs after __napi_schedule")
This shows that relying on the caller to arrange a proper context for
the softirqs to be handled while calling napi_schedule() is very fragile
and error prone. Also fixing them can also prove challenging if the
caller may be called from different kinds of contexts.
Therefore fix this from napi_schedule() itself with waking up ksoftirqd
when softirqs are raised from task contexts.
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reported-by: Jakub Kicinski <kuba@kernel.org>
Reported-by: Francois Romieu <romieu@fr.zoreil.com>
Closes: https://lore.kernel.org/lkml/354a2690-9bbf-4ccb-8769-fa94707a9340@molgen.mpg.de/
Cc: Breno Leitao <leitao@debian.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250223221708.27130-1-frederic@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 505ead7ab7 ]
The function __netpoll_send_skb() is being invoked without holding the
RCU read lock. This oversight triggers a warning message when
CONFIG_PROVE_RCU_LIST is enabled:
net/core/netpoll.c:330 suspicious rcu_dereference_check() usage!
netpoll_send_skb
netpoll_send_udp
write_ext_msg
console_flush_all
console_unlock
vprintk_emit
To prevent npinfo from disappearing unexpectedly, ensure that
__netpoll_send_skb() is protected with the RCU read lock.
Fixes: 2899656b49 ("netpoll: take rcu_read_lock_bh() in netpoll_send_skb_on_dev()")
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250306-netpoll_rcu_v2-v2-1-bc4f5c51742a@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49806fe6e6 ]
In certain cases, napi_get_frags() returns an skb that points to an old
received fragment, This skb may have its skb->ip_summed, csum, and other
fields set from previous fragment handling.
Some network drivers set skb->ip_summed to either CHECKSUM_COMPLETE or
CHECKSUM_UNNECESSARY when getting skb from napi_get_frags(), while
others only set skb->ip_summed when RX checksum offload is enabled on
the device, and do not set any value for skb->ip_summed when hardware
checksum offload is disabled, assuming that the skb->ip_summed
initiated to zero by napi_reuse_skb, ionic driver for example will
ignore/unset any value for the ip_summed filed if HW checksum offload is
disabled, and if we have a situation where the user disables the
checksum offload during a traffic that could lead to the following
errors shown in the kernel logs:
<IRQ>
dump_stack_lvl+0x34/0x48
__skb_gro_checksum_complete+0x7e/0x90
tcp6_gro_receive+0xc6/0x190
ipv6_gro_receive+0x1ec/0x430
dev_gro_receive+0x188/0x360
? ionic_rx_clean+0x25a/0x460 [ionic]
napi_gro_frags+0x13c/0x300
? __pfx_ionic_rx_service+0x10/0x10 [ionic]
ionic_rx_service+0x67/0x80 [ionic]
ionic_cq_service+0x58/0x90 [ionic]
ionic_txrx_napi+0x64/0x1b0 [ionic]
__napi_poll+0x27/0x170
net_rx_action+0x29c/0x370
handle_softirqs+0xce/0x270
__irq_exit_rcu+0xa3/0xc0
common_interrupt+0x80/0xa0
</IRQ>
This inconsistency sometimes leads to checksum validation issues in the
upper layers of the network stack.
To resolve this, this patch clears the skb->ip_summed value for each
reused skb in by napi_reuse_skb(), ensuring that the caller is responsible
for setting the correct checksum status. This eliminates potential
checksum validation issues caused by improper handling of
skb->ip_summed.
Fixes: 76620aafd6 ("gro: New frags interface to avoid copying shinfo")
Signed-off-by: Mohammad Heib <mheib@redhat.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250225112852.2507709-1-mheib@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de2c211868 ]
We found an issue when using bpf_redirect with ipvs NAT mode after
commit ff70202b2d ("dev_forward_skb: do not scrub skb mark within
the same name space"). Particularly, we use bpf_redirect to return
the skb directly back to the netif it comes from, i.e., xnet is
false in skb_scrub_packet(), and then ipvs_property is preserved
and SNAT is skipped in the rx path.
ipvs_property has been already cleared when netns is changed in
commit 2b5ec1a5f9 ("netfilter/ipvs: clear ipvs_property flag when
SKB net namespace changed"). This patch just clears it in spite of
netns.
Fixes: 2b5ec1a5f9 ("netfilter/ipvs: clear ipvs_property flag when SKB net namespace changed")
Signed-off-by: Philo Lu <lulie@linux.alibaba.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Link: https://patch.msgid.link/20250222033518.126087-1-lulie@linux.alibaba.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c180188ec0 ]
Commit 7acf8a1e8a ("Replace 2 jiffies with sysctl netdev_budget_usecs
to enable softirq tuning") added a possibility to set
net_hotdata.netdev_budget_usecs, but added no lower bound checking.
Commit a4837980fd ("net: revert default NAPI poll timeout to 2 jiffies")
made the *initial* value HZ-dependent, so the initial value is at least
2 jiffies even for lower HZ values (2 ms for 1000 Hz, 8ms for 250 Hz, 20
ms for 100 Hz).
But a user still can set improper values by a sysctl. Set .extra1
(the lower bound) for net_hotdata.netdev_budget_usecs to the same value
as in the latter commit. That is to 2 jiffies.
Fixes: a4837980fd ("net: revert default NAPI poll timeout to 2 jiffies")
Fixes: 7acf8a1e8a ("Replace 2 jiffies with sysctl netdev_budget_usecs to enable softirq tuning")
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Dmitry Yakunin <zeil@yandex-team.ru>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Link: https://patch.msgid.link/20250220110752.137639-1-jirislaby@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5459cce6bf ]
Currently, only TCP supports strparser, but sockmap doesn't intercept
non-TCP connections to attach strparser. For example, with UDP, although
the read/write handlers are replaced, strparser is not executed due to
the lack of a read_sock operation.
Furthermore, in udp_bpf_recvmsg(), it checks whether the psock has data,
and if not, it falls back to the native UDP read interface, making
UDP + strparser appear to read correctly. According to its commit history,
this behavior is unexpected.
Moreover, since UDP lacks the concept of streams, we intercept it directly.
Fixes: 1fa1fe8ff1 ("bpf, sockmap: Test shutdown() correctly exits epoll and recv()=0")
Signed-off-by: Jiayuan Chen <mrpre@163.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Acked-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://patch.msgid.link/20250122100917.49845-4-mrpre@163.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36b62df568 ]
'sk->copied_seq' was updated in the tcp_eat_skb() function when the action
of a BPF program was SK_REDIRECT. For other actions, like SK_PASS, the
update logic for 'sk->copied_seq' was moved to tcp_bpf_recvmsg_parser()
to ensure the accuracy of the 'fionread' feature.
It works for a single stream_verdict scenario, as it also modified
sk_data_ready->sk_psock_verdict_data_ready->tcp_read_skb
to remove updating 'sk->copied_seq'.
However, for programs where both stream_parser and stream_verdict are
active (strparser purpose), tcp_read_sock() was used instead of
tcp_read_skb() (sk_data_ready->strp_data_ready->tcp_read_sock).
tcp_read_sock() now still updates 'sk->copied_seq', leading to duplicate
updates.
In summary, for strparser + SK_PASS, copied_seq is redundantly calculated
in both tcp_read_sock() and tcp_bpf_recvmsg_parser().
The issue causes incorrect copied_seq calculations, which prevent
correct data reads from the recv() interface in user-land.
We do not want to add new proto_ops to implement a new version of
tcp_read_sock, as this would introduce code complexity [1].
We could have added noack and copied_seq to desc, and then called
ops->read_sock. However, unfortunately, other modules didn’t fully
initialize desc to zero. So, for now, we are directly calling
tcp_read_sock_noack() in tcp_bpf.c.
[1]: https://lore.kernel.org/bpf/20241218053408.437295-1-mrpre@163.com
Fixes: e5c6de5fa0 ("bpf, sockmap: Incorrectly handling copied_seq")
Suggested-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Jiayuan Chen <mrpre@163.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://patch.msgid.link/20250122100917.49845-3-mrpre@163.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e5796862c ]
This patch fixes a bug in TC flower filter where rules combining a
specific destination port with a source port range weren't working
correctly.
The specific case was when users tried to configure rules like:
tc filter add dev ens38 ingress protocol ip flower ip_proto udp \
dst_port 5000 src_port 2000-3000 action drop
The root cause was in the flow dissector code. While both
FLOW_DISSECTOR_KEY_PORTS and FLOW_DISSECTOR_KEY_PORTS_RANGE flags
were being set correctly in the classifier, the __skb_flow_dissect_ports()
function was only populating one of them: whichever came first in
the enum check. This meant that when the code needed both a specific
port and a port range, one of them would be left as 0, causing the
filter to not match packets as expected.
Fix it by removing the either/or logic and instead checking and
populating both key types independently when they're in use.
Fixes: 8ffb055bea ("cls_flower: Fix the behavior using port ranges with hw-offload")
Reported-by: Qiang Zhang <dtzq01@gmail.com>
Closes: https://lore.kernel.org/netdev/CAPx+-5uvFxkhkz4=j_Xuwkezjn9U6kzKTD5jz4tZ9msSJ0fOJA@mail.gmail.com/
Cc: Yoshiki Komachi <komachi.yoshiki@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20250218043210.732959-2-xiyou.wangcong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fb5bb169d ]
sockmap expects all vsocks to have a transport assigned, which is expressed
in vsock_proto::psock_update_sk_prot(). However, there is an edge case
where an unconnected (connectible) socket may lose its previously assigned
transport. This is handled with a NULL check in the vsock/BPF recv path.
Another design detail is that listening vsocks are not supposed to have any
transport assigned at all. Which implies they are not supported by the
sockmap. But this is complicated by the fact that a socket, before
switching to TCP_LISTEN, may have had some transport assigned during a
failed connect() attempt. Hence, we may end up with a listening vsock in a
sockmap, which blows up quickly:
KASAN: null-ptr-deref in range [0x0000000000000120-0x0000000000000127]
CPU: 7 UID: 0 PID: 56 Comm: kworker/7:0 Not tainted 6.14.0-rc1+
Workqueue: vsock-loopback vsock_loopback_work
RIP: 0010:vsock_read_skb+0x4b/0x90
Call Trace:
sk_psock_verdict_data_ready+0xa4/0x2e0
virtio_transport_recv_pkt+0x1ca8/0x2acc
vsock_loopback_work+0x27d/0x3f0
process_one_work+0x846/0x1420
worker_thread+0x5b3/0xf80
kthread+0x35a/0x700
ret_from_fork+0x2d/0x70
ret_from_fork_asm+0x1a/0x30
For connectible sockets, instead of relying solely on the state of
vsk->transport, tell sockmap to only allow those representing established
connections. This aligns with the behaviour for AF_INET and AF_UNIX.
Fixes: 634f1a7110 ("vsock: support sockmap")
Signed-off-by: Michal Luczaj <mhal@rbox.co>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c25bdd2ac8 ]
The initial value of err is -ENOBUFS, and err is guaranteed to be
less than 0 before all goto errout. Therefore, on the error path
of errout, there is no need to repeatedly judge that err is less than 0,
and delete redundant judgments to make the code more concise.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: becbd5850c ("neighbour: use RCU protection in __neigh_notify()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ac412a336 ]
MEM_WRITE attribute is defined as: "Non-presence of MEM_WRITE means that
MEM is only being read". bpf_load_hdr_opt() both reads and writes from
its arg2 - void *search_res.
This matters a lot for the next commit where we more precisely track
stack accesses. Without this annotation, the verifier will make false
assumptions about the contents of memory written to by helpers and
possibly prune valid branches.
Fixes: 6fad274f06 ("bpf: Add MEM_WRITE attribute")
Acked-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Daniel Xu <dxu@dxuuu.xyz>
Link: https://lore.kernel.org/r/730e45f8c39be2a5f3d8c4406cceca9d574cbf14.1736886479.git.dxu@dxuuu.xyz
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1f9f79fa2 ]
The following problem was encountered during stability test:
(NULL net_device): NAPI poll function process_backlog+0x0/0x530 \
returned 1, exceeding its budget of 0.
------------[ cut here ]------------
list_add double add: new=ffff88905f746f48, prev=ffff88905f746f48, \
next=ffff88905f746e40.
WARNING: CPU: 18 PID: 5462 at lib/list_debug.c:35 \
__list_add_valid_or_report+0xf3/0x130
CPU: 18 UID: 0 PID: 5462 Comm: ping Kdump: loaded Not tainted 6.13.0-rc7+
RIP: 0010:__list_add_valid_or_report+0xf3/0x130
Call Trace:
? __warn+0xcd/0x250
? __list_add_valid_or_report+0xf3/0x130
enqueue_to_backlog+0x923/0x1070
netif_rx_internal+0x92/0x2b0
__netif_rx+0x15/0x170
loopback_xmit+0x2ef/0x450
dev_hard_start_xmit+0x103/0x490
__dev_queue_xmit+0xeac/0x1950
ip_finish_output2+0x6cc/0x1620
ip_output+0x161/0x270
ip_push_pending_frames+0x155/0x1a0
raw_sendmsg+0xe13/0x1550
__sys_sendto+0x3bf/0x4e0
__x64_sys_sendto+0xdc/0x1b0
do_syscall_64+0x5b/0x170
entry_SYSCALL_64_after_hwframe+0x76/0x7e
The reproduction command is as follows:
sysctl -w net.core.dev_weight=0
ping 127.0.0.1
This is because when the napi's weight is set to 0, process_backlog() may
return 0 and clear the NAPI_STATE_SCHED bit of napi->state, causing this
napi to be re-polled in net_rx_action() until __do_softirq() times out.
Since the NAPI_STATE_SCHED bit has been cleared, napi_schedule_rps() can
be retriggered in enqueue_to_backlog(), causing this issue.
Making the napi's weight always non-zero solves this problem.
Triggering this issue requires system-wide admin (setting is
not namespaced).
Fixes: e387660545 ("[NET]: Fix sysctl net.core.dev_weight")
Fixes: 3d48b53fb2 ("net: dev_weight: TX/RX orthogonality")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Link: https://patch.msgid.link/20250116143053.4146855-1-liujian56@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd4f101edb ]
Many (struct pernet_operations)->exit_batch() methods have
to acquire rtnl.
In presence of rtnl mutex pressure, this makes cleanup_net()
very slow.
This patch adds a new exit_batch_rtnl() method to reduce
number of rtnl acquisitions from cleanup_net().
exit_batch_rtnl() handlers are called while rtnl is locked,
and devices to be killed can be queued in a list provided
as their second argument.
A single unregister_netdevice_many() is called right
before rtnl is released.
exit_batch_rtnl() handlers are called before ->exit() and
->exit_batch() handlers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20240206144313.2050392-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 46841c7053 ("gtp: Use for_each_netdev_rcu() in gtp_genl_dump_pdp().")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76201b5979 ]
Passing a sufficient amount of imix entries leads to invalid access to the
pkt_dev->imix_entries array because of the incorrect boundary check.
UBSAN: array-index-out-of-bounds in net/core/pktgen.c:874:24
index 20 is out of range for type 'imix_pkt [20]'
CPU: 2 PID: 1210 Comm: bash Not tainted 6.10.0-rc1 #121
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996)
Call Trace:
<TASK>
dump_stack_lvl lib/dump_stack.c:117
__ubsan_handle_out_of_bounds lib/ubsan.c:429
get_imix_entries net/core/pktgen.c:874
pktgen_if_write net/core/pktgen.c:1063
pde_write fs/proc/inode.c:334
proc_reg_write fs/proc/inode.c:346
vfs_write fs/read_write.c:593
ksys_write fs/read_write.c:644
do_syscall_64 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe arch/x86/entry/entry_64.S:130
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 52a62f8603 ("pktgen: Parse internet mix (imix) input")
Signed-off-by: Artem Chernyshev <artem.chernyshev@red-soft.ru>
[ fp: allow to fill the array completely; minor changelog cleanup ]
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3af60928a ]
As pointed out in the original comment, lookup in sockmap can return a TCP
ESTABLISHED socket. Such TCP socket may have had SO_ATTACH_REUSEPORT_EBPF
set before it was ESTABLISHED. In other words, a non-NULL sk_reuseport_cb
does not imply a non-refcounted socket.
Drop sk's reference in both error paths.
unreferenced object 0xffff888101911800 (size 2048):
comm "test_progs", pid 44109, jiffies 4297131437
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
80 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace (crc 9336483b):
__kmalloc_noprof+0x3bf/0x560
__reuseport_alloc+0x1d/0x40
reuseport_alloc+0xca/0x150
reuseport_attach_prog+0x87/0x140
sk_reuseport_attach_bpf+0xc8/0x100
sk_setsockopt+0x1181/0x1990
do_sock_setsockopt+0x12b/0x160
__sys_setsockopt+0x7b/0xc0
__x64_sys_setsockopt+0x1b/0x30
do_syscall_64+0x93/0x180
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Fixes: 64d85290d7 ("bpf: Allow bpf_map_lookup_elem for SOCKMAP and SOCKHASH")
Signed-off-by: Michal Luczaj <mhal@rbox.co>
Reviewed-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://patch.msgid.link/20250110-reuseport-memleak-v1-1-fa1ddab0adfe@rbox.co
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68e068cabd ]
The blamed commit disabled hardware offoad of IPv6 packets with
extension headers on devices that advertise NETIF_F_IPV6_CSUM,
based on the definition of that feature in skbuff.h:
* * - %NETIF_F_IPV6_CSUM
* - Driver (device) is only able to checksum plain
* TCP or UDP packets over IPv6. These are specifically
* unencapsulated packets of the form IPv6|TCP or
* IPv6|UDP where the Next Header field in the IPv6
* header is either TCP or UDP. IPv6 extension headers
* are not supported with this feature. This feature
* cannot be set in features for a device with
* NETIF_F_HW_CSUM also set. This feature is being
* DEPRECATED (see below).
The change causes skb_warn_bad_offload to fire for BIG TCP
packets.
[ 496.310233] WARNING: CPU: 13 PID: 23472 at net/core/dev.c:3129 skb_warn_bad_offload+0xc4/0xe0
[ 496.310297] ? skb_warn_bad_offload+0xc4/0xe0
[ 496.310300] skb_checksum_help+0x129/0x1f0
[ 496.310303] skb_csum_hwoffload_help+0x150/0x1b0
[ 496.310306] validate_xmit_skb+0x159/0x270
[ 496.310309] validate_xmit_skb_list+0x41/0x70
[ 496.310312] sch_direct_xmit+0x5c/0x250
[ 496.310317] __qdisc_run+0x388/0x620
BIG TCP introduced an IPV6_TLV_JUMBO IPv6 extension header to
communicate packet length, as this is an IPv6 jumbogram. But, the
feature is only enabled on devices that support BIG TCP TSO. The
header is only present for PF_PACKET taps like tcpdump, and not
transmitted by physical devices.
For this specific case of extension headers that are not
transmitted, return to the situation before the blamed commit
and support hardware offload.
ipv6_has_hopopt_jumbo() tests not only whether this header is present,
but also that it is the only extension header before a terminal (L4)
header.
Fixes: 04c20a9356 ("net: skip offload for NETIF_F_IPV6_CSUM if ipv6 header contains extension")
Reported-by: syzbot <syzkaller@googlegroups.com>
Reported-by: Eric Dumazet <edumazet@google.com>
Closes: https://lore.kernel.org/netdev/CANn89iK1hdC3Nt8KPhOtTF8vCPc1AHDCtse_BTNki1pWxAByTQ@mail.gmail.com/
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250101164909.1331680-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ecc4d858b ]
skb_network_offset() and skb_transport_offset() can be negative when
they are called after we pull the transport header, for example, when
we use eBPF sockmap at the point of ->sk_data_ready().
__bpf_skb_min_len() uses an unsigned int to get these offsets, this
leads to a very large number which then causes bpf_skb_change_tail()
failed unexpectedly.
Fix this by using a signed int to get these offsets and ensure the
minimum is at least zero.
Fixes: 5293efe62d ("bpf: add bpf_skb_change_tail helper")
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20241213034057.246437-2-xiyou.wangcong@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d888b7af7c ]
When we do sk_psock_verdict_apply->sk_psock_skb_ingress, an sk_msg will
be created out of the skb, and the rmem accounting of the sk_msg will be
handled by the skb.
For skmsgs in __SK_REDIRECT case of tcp_bpf_send_verdict, when redirecting
to the ingress of a socket, although we sk_rmem_schedule and add sk_msg to
the ingress_msg of sk_redir, we do not update sk_rmem_alloc. As a result,
except for the global memory limit, the rmem of sk_redir is nearly
unlimited. Thus, add sk_rmem_alloc related logic to limit the recv buffer.
Since the function sk_msg_recvmsg and __sk_psock_purge_ingress_msg are
used in these two paths. We use "msg->skb" to test whether the sk_msg is
skb backed up. If it's not, we shall do the memory accounting explicitly.
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: Zijian Zhang <zijianzhang@bytedance.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20241210012039.1669389-3-zijianzhang@bytedance.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 75e072a390 upstream.
Consider a sockmap entry being updated with the same socket:
osk = stab->sks[idx];
sock_map_add_link(psock, link, map, &stab->sks[idx]);
stab->sks[idx] = sk;
if (osk)
sock_map_unref(osk, &stab->sks[idx]);
Due to sock_map_unref(), which invokes sock_map_del_link(), all the
psock's links for stab->sks[idx] are torn:
list_for_each_entry_safe(link, tmp, &psock->link, list) {
if (link->link_raw == link_raw) {
...
list_del(&link->list);
sk_psock_free_link(link);
}
}
And that includes the new link sock_map_add_link() added just before
the unref.
This results in a sockmap holding a socket, but without the respective
link. This in turn means that close(sock) won't trigger the cleanup,
i.e. a closed socket will not be automatically removed from the sockmap.
Stop tearing the links when a matching link_raw is found.
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: Michal Luczaj <mhal@rbox.co>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20241202-sockmap-replace-v1-1-1e88579e7bd5@rbox.co
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c69c5e10ad ]
The ndev->npinfo pointer in __netpoll_setup() is RCU-protected but is being
accessed directly for a NULL check. While no RCU read lock is held in this
context, we should still use proper RCU primitives for consistency and
correctness.
Replace the direct NULL check with rcu_access_pointer(), which is the
appropriate primitive when only checking for NULL without dereferencing
the pointer. This function provides the necessary ordering guarantees
without requiring RCU read-side protection.
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20241118-netpoll_rcu-v1-1-a1888dcb4a02@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0de6a472c3 ]
Commit 51183d233b ("net/neighbor: Update neigh_dump_info for strict
data checking") added strict checking. The err variable is not cleared,
so if we find no table to dump we will return the validation error even
if user did not want strict checking.
I think the only way to hit this is to send an buggy request, and ask
for a table which doesn't exist, so there's no point treating this
as a real fix. I only noticed it because a syzbot repro depended on it
to trigger another bug.
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241115003221.733593-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ca2a1eead ]
When the stream_verdict program returns SK_PASS, it places the received skb
into its own receive queue, but a recursive lock eventually occurs, leading
to an operating system deadlock. This issue has been present since v6.9.
'''
sk_psock_strp_data_ready
write_lock_bh(&sk->sk_callback_lock)
strp_data_ready
strp_read_sock
read_sock -> tcp_read_sock
strp_recv
cb.rcv_msg -> sk_psock_strp_read
# now stream_verdict return SK_PASS without peer sock assign
__SK_PASS = sk_psock_map_verd(SK_PASS, NULL)
sk_psock_verdict_apply
sk_psock_skb_ingress_self
sk_psock_skb_ingress_enqueue
sk_psock_data_ready
read_lock_bh(&sk->sk_callback_lock) <= dead lock
'''
This topic has been discussed before, but it has not been fixed.
Previous discussion:
https://lore.kernel.org/all/6684a5864ec86_403d20898@john.notmuch
Fixes: 6648e61322 ("bpf, skmsg: Fix NULL pointer dereference in sk_psock_skb_ingress_enqueue")
Reported-by: Vincent Whitchurch <vincent.whitchurch@datadoghq.com>
Signed-off-by: Jiayuan Chen <mrpre@163.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://patch.msgid.link/20241118030910.36230-2-mrpre@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86e8921df0 ]
TCPDIAG_GETSOCK and DCCPDIAG_GETSOCK diag are serialized
on sock_diag_table_mutex.
This is to make sure inet_diag module is not unloaded
while diag was ongoing.
It is time to get rid of this mutex and use RCU protection,
allowing full parallelism.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stable-dep-of: eb02688c5c ("ipv6: release nexthop on device removal")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d55a69747 ]
sock_diag_broadcast_destroy_work() and __sock_diag_cmd()
are currently using sock_diag_table_mutex to protect
against concurrent sock_diag_handlers[] changes.
This makes inet_diag dump serialized, thus less scalable
than legacy /proc files.
It is time to switch to full RCU protection.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stable-dep-of: eb02688c5c ("ipv6: release nexthop on device removal")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 955afd57dc ]
Found in the test_txmsg_pull in test_sockmap,
```
txmsg_cork = 512; // corking is importrant here
opt->iov_length = 3;
opt->iov_count = 1;
opt->rate = 512; // sendmsg will be invoked 512 times
```
The first sendmsg will send an sk_msg with size 3, and bpf_msg_pull_data
will be invoked the first time. sk_msg_reset_curr will reset the copybreak
from 3 to 0. In the second sendmsg, since we are in the stage of corking,
psock->cork will be reused in func sk_msg_alloc. msg->sg.copybreak is 0
now, the second msg will overwrite the first msg. As a result, we could
not pass the data integrity test.
The same problem happens in push and pop test. Thus, fix sk_msg_reset_curr
to restore the correct copybreak.
Fixes: bb9aefde5b ("bpf: sockmap, updating the sg structure should also update curr")
Signed-off-by: Zijian Zhang <zijianzhang@bytedance.com>
Link: https://lore.kernel.org/r/20241106222520.527076-9-zijianzhang@bytedance.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d609ba262 ]
Several fixes to bpf_msg_pop_data,
1. In sk_msg_shift_left, we should put_page
2. if (len == 0), return early is better
3. pop the entire sk_msg (last == msg->sg.size) should be supported
4. Fix for the value of variable "a"
5. In sk_msg_shift_left, after shifting, i has already pointed to the next
element. Addtional sk_msg_iter_var_next may result in BUG.
Fixes: 7246d8ed4d ("bpf: helper to pop data from messages")
Signed-off-by: Zijian Zhang <zijianzhang@bytedance.com>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/r/20241106222520.527076-8-zijianzhang@bytedance.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15ab0548e3 ]
Several fixes to bpf_msg_push_data,
1. test_sockmap has tests where bpf_msg_push_data is invoked to push some
data at the end of a message, but -EINVAL is returned. In this case, in
bpf_msg_push_data, after the first loop, i will be set to msg->sg.end, add
the logic to handle it.
2. In the code block of "if (start - offset)", it's possible that "i"
points to the last of sk_msg_elem. In this case, "sk_msg_iter_next(msg,
end)" might still be called twice, another invoking is in "if (!copy)"
code block, but actually only one is needed. Add the logic to handle it,
and reconstruct the code to make the logic more clear.
Fixes: 6fff607e2f ("bpf: sk_msg program helper bpf_msg_push_data")
Signed-off-by: Zijian Zhang <zijianzhang@bytedance.com>
Link: https://lore.kernel.org/r/20241106222520.527076-7-zijianzhang@bytedance.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb86c42a2a ]
In the bpf_out_neigh_v6 function, rcu_read_lock() is used to begin an RCU
read-side critical section. However, when unlocking, one branch
incorrectly uses a different RCU unlock flavour rcu_read_unlock_bh()
instead of rcu_read_unlock(). This mismatch in RCU locking flavours can
lead to unexpected behavior and potential concurrency issues.
This possible bug was identified using a static analysis tool developed
by myself, specifically designed to detect RCU-related issues.
This patch corrects the mismatched unlock flavour by replacing the
incorrect rcu_read_unlock_bh() with the appropriate rcu_read_unlock(),
ensuring that the RCU critical section is properly exited. This change
prevents potential synchronization issues and aligns with proper RCU
usage patterns.
Fixes: 09eed1192c ("neighbour: switch to standard rcu, instead of rcu_bh")
Signed-off-by: Jiawei Ye <jiawei.ye@foxmail.com>
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Link: https://lore.kernel.org/r/tencent_CFD3D1C3D68B45EA9F52D8EC76D2C4134306@qq.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04c20a9356 ]
As documented in skbuff.h, devices with NETIF_F_IPV6_CSUM capability
can only checksum TCP and UDP over IPv6 if the IP header does not
contains extension.
This is enforced for UDP packets emitted from user-space to an IPv6
address as they go through ip6_make_skb(), which calls
__ip6_append_data() where a check is done on the header size before
setting CHECKSUM_PARTIAL.
But the introduction of UDP encapsulation with fou6 added a code-path
where it is possible to get an skb with a partial UDP checksum and an
IPv6 header with extension:
* fou6 adds a UDP header with a partial checksum if the inner packet
does not contains a valid checksum.
* ip6_tunnel adds an IPv6 header with a destination option extension
header if encap_limit is non-zero (the default value is 4).
The thread linked below describes in more details how to reproduce the
problem with GRE-in-UDP tunnel.
Add a check on the network header size in skb_csum_hwoffload_help() to
make sure no IPv6 packet with extension header is handed to a network
device with NETIF_F_IPV6_CSUM capability.
Link: https://lore.kernel.org/netdev/26548921.1r3eYUQgxm@benoit.monin/T/#u
Fixes: aa3463d65e ("fou: Add encap ops for IPv6 tunnels")
Signed-off-by: Benoît Monin <benoit.monin@gmx.fr>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/5fbeecfc311ea182aa1d1c771725ab8b4cac515e.1729778144.git.benoit.monin@gmx.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ab5cf19fb ]
Config a small gso_max_size/gso_ipv4_max_size will lead to an underflow
in sk_dst_gso_max_size(), which may trigger a BUG_ON crash,
because sk->sk_gso_max_size would be much bigger than device limits.
Call Trace:
tcp_write_xmit
tso_segs = tcp_init_tso_segs(skb, mss_now);
tcp_set_skb_tso_segs
tcp_skb_pcount_set
// skb->len = 524288, mss_now = 8
// u16 tso_segs = 524288/8 = 65535 -> 0
tso_segs = DIV_ROUND_UP(skb->len, mss_now)
BUG_ON(!tso_segs)
Add check for the minimum value of gso_max_size and gso_ipv4_max_size.
Fixes: 46e6b992c2 ("rtnetlink: allow GSO maximums to be set on device creation")
Fixes: 9eefedd58a ("net: add gso_ipv4_max_size and gro_ipv4_max_size per device")
Signed-off-by: Wang Liang <wangliang74@huawei.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241023035213.517386-1-wangliang74@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14a3d3ef02 ]
We can now undo parts of 4b3786a6c5 ("bpf: Zero former ARG_PTR_TO_{LONG,INT}
args in case of error") as discussed in [0].
Given the BPF helpers now have MEM_WRITE tag, the MEM_UNINIT can be cleared.
The mtu_len is an input as well as output argument, meaning, the BPF program
has to set it to something. It cannot be uninitialized. Therefore, allowing
uninitialized memory and zeroing it on error would be odd. It was done as
an interim step in 4b3786a6c5 as the desired behavior could not have been
expressed before the introduction of MEM_WRITE tag.
Fixes: 4b3786a6c5 ("bpf: Zero former ARG_PTR_TO_{LONG,INT} args in case of error")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/a86eb76d-f52f-dee4-e5d2-87e45de3e16f@iogearbox.net [0]
Acked-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20241021152809.33343-3-daniel@iogearbox.net
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Willem de BruijnandGreg Kroah-Hartman
Jason XingandGreg Kroah-Hartman
Antoine TenartandGreg Kroah-Hartman
Mark ZhangandGreg Kroah-Hartman
Lin MaandGreg Kroah-Hartman
Justin IurmanandGreg Kroah-Hartman
Frederic WeisbeckerandGreg Kroah-Hartman
Breno LeitaoandGreg Kroah-Hartman
Mohammad HeibandGreg Kroah-Hartman
Philo LuandGreg Kroah-Hartman
Jiri Slaby (SUSE)andGreg Kroah-Hartman
Gavrilov IliaandGreg Kroah-Hartman
Jiayuan ChenandGreg Kroah-Hartman
Cong WangandGreg Kroah-Hartman
Michal LuczajandGreg Kroah-Hartman
Eric DumazetandGreg Kroah-Hartman
Li ZetaoandGreg Kroah-Hartman
Toke Høiland-JørgensenandGreg Kroah-Hartman
Daniel XuandGreg Kroah-Hartman
Liu JianandGreg Kroah-Hartman
Artem ChernyshevandGreg Kroah-Hartman
Kuniyuki IwashimaandGreg Kroah-Hartman
Cong WangandGreg Kroah-Hartman
Zijian ZhangandGreg Kroah-Hartman
Jakub KicinskiandGreg Kroah-Hartman
Jiawei YeandGreg Kroah-Hartman
Benoît MoninandGreg Kroah-Hartman
Wang LiangandGreg Kroah-Hartman
Daniel BorkmannandGreg Kroah-Hartman