[ Upstream commit aff12700b8 ]
idt_scan_mws() puts a large fixed-size array on the stack and copies
it into a smaller dynamically allocated array at the end. On 32-bit
targets, the fixed size can easily exceed the warning limit for
possible stack overflow:
drivers/ntb/hw/idt/ntb_hw_idt.c:1041:27: error: stack frame size (1032) exceeds limit (1024) in 'idt_scan_mws' [-Werror,-Wframe-larger-than]
Change it to instead just always use dynamic allocation for the
array from the start. It's too big for the stack, but not actually
all that much for a permanent allocation.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/all/202205111109.PiKTruEj-lkp@intel.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fd5625fc86 upstream.
msi_db_mask is of type 'u64', still the standard 'int' arithmetic is
performed to compute its value.
While most of the ntb_hw drivers actually don't utilize the higher 32
bits of the doorbell mask now, this may be the case for Switchtec - see
switchtec_ntb_init_db().
Found by Linux Verification Center (linuxtesting.org) with SVACE static
analysis tool.
Fixes: 2b0569b3b7 ("NTB: Add MSI interrupt support to ntb_transport")
Cc: stable@vger.kernel.org
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4279e72cab upstream.
The function call “dmaengine_unmap_put(unmap)” was used in an if branch.
The same call was immediately triggered by a subsequent goto statement.
Thus avoid such a call repetition.
This issue was detected by using the Coccinelle software.
Fixes: 5648e56d03 ("NTB: ntb_perf: Add full multi-port NTB API support")
Cc: stable@vger.kernel.org
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit de203da734 ]
There is a kernel API ntb_mw_clear_trans() would pass 0 to both addr and
size. This would make xlate_pos negative.
[ 23.734156] switchtec switchtec0: MW 0: part 0 addr 0x0000000000000000 size 0x0000000000000000
[ 23.734158] ================================================================================
[ 23.734172] UBSAN: shift-out-of-bounds in drivers/ntb/hw/mscc/ntb_hw_switchtec.c:293:7
[ 23.734418] shift exponent -1 is negative
Ensuring xlate_pos is a positive or zero before BIT.
Fixes: 1e2fd202f8 ("ntb_hw_switchtec: Check for alignment of the buffer in mw_set_trans()")
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e51aded92d ]
In the switchtec_ntb_add function, it can call switchtec_ntb_init_sndev
function, then &sndev->check_link_status_work is bound with
check_link_status_work. switchtec_ntb_link_notification may be called
to start the work.
If we remove the module which will call switchtec_ntb_remove to make
cleanup, it will free sndev through kfree(sndev), while the work
mentioned above will be used. The sequence of operations that may lead
to a UAF bug is as follows:
CPU0 CPU1
| check_link_status_work
switchtec_ntb_remove |
kfree(sndev); |
| if (sndev->link_force_down)
| // use sndev
Fix it by ensuring that the work is canceled before proceeding with
the cleanup in switchtec_ntb_remove.
Signed-off-by: Kaixin Wang <kxwang23@m.fudan.edu.cn>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 061a785a11 ]
Physical addresses under IOVA on x86 platform are mapped contiguously
as a side effect before the patch that removed CONFIG_DMA_REMAP. The
NTB rx buffer ring is a single chunk DMA buffer that is allocated
against the NTB PCI device. If the receive side is using a DMA device,
then the buffers are remapped against the DMA device before being
submitted via the dmaengine API. This scheme becomes a problem when
the physical memory is discontiguous. When dma_map_page() is called
on the kernel virtual address from the dma_alloc_coherent() call, the
new IOVA mapping no longer points to all the physical memory allocated
due to being discontiguous. Change dma_alloc_coherent() to dma_alloc_attrs()
in order to force DMA_ATTR_FORCE_CONTIGUOUS attribute. This is the best
fix for the circumstance. A potential future solution may be having the DMA
mapping API providing a way to alias an existing IOVA mapping to a new
device perhaps.
This fix is not to fix the patch pointed to by the fixes tag, but to fix
the issue arised in the ntb_transport driver on x86 platforms after the
said patch is applied.
Reported-by: Jerry Dai <jerry.dai@intel.com>
Fixes: f5ff79fddf ("dma-mapping: remove CONFIG_DMA_REMAP")
Tested-by: Jerry Dai <jerry.dai@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e229897d37 ]
The debugfs_create_dir() function returns error pointers.
It never returns NULL. So use IS_ERR() to check it.
Fixes: e26a5843f7 ("NTB: Split ntb_hw_intel and ntb_transport drivers")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aebfdfe39b ]
If device_register() fails in ntb_register_device(), the device name
allocated by dev_set_name() should be freed. As per the comment in
device_register(), callers should use put_device() to give up the
reference in the error path. So fix this by calling put_device() in the
error path so that the name can be freed in kobject_cleanup().
As a result of this, put_device() in the error path of
ntb_register_device() is removed and the actual error is returned.
Fixes: a1bd3baeb2 ("NTB: Add NTB hardware abstraction layer")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20231201033057.1399131-1-yangyingliang@huaweicloud.com
[mani: reworded commit message]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5a7693e6bb upstream.
ntb_transport_tx_free_entry() never returns 0 with the current
calculation. If head == tail, then it would return qp->tx_max_entry.
Change compare to tail >= head and when they are equal, a 0 would be
returned.
Fixes: e74bfeedad ("NTB: Add flow control to the ntb_netdev")
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: renlonglong <ren.longlong@h3c.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc79bd2738 upstream.
The tx tail index is not reset when the link goes down. This causes the
tail index to go out of sync when the link goes down and comes back up.
Refactor the ntb_qp_link_down_reset() and reset the tail index as well.
Fixes: 2849b5d706 ("NTB: Reset transport QP link stats on down")
Reported-by: Yuan Y Lu <yuan.y.lu@intel.com>
Tested-by: Yuan Y Lu <yuan.y.lu@intel.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f195a1a6fe upstream.
Currently when the transport receive packets after netdev has closed the
transport returns error and triggers tx errors to be incremented and
carrier to be stopped. There is no reason to return error if the device is
already closed. Drop the packet and return 0.
Fixes: e26a5843f7 ("NTB: Split ntb_hw_intel and ntb_transport drivers")
Reported-by: Yuan Y Lu <yuan.y.lu@intel.com>
Tested-by: Yuan Y Lu <yuan.y.lu@intel.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2790143f09 ]
As the devm_kcalloc may return NULL pointer,
it should be better to add check for the return
value, as same as the others.
Fixes: 7f46c8b3a5 ("NTB: ntb_tool: Add full multi-port NTB API support")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8623ccbfc5 ]
If device_register() returns error, the name allocated by
dev_set_name() need be freed. As comment of device_register()
says, it should use put_device() to give up the reference in
the error path. So fix this by calling put_device(), then the
name can be freed in kobject_cleanup(), and client_dev is freed
in ntb_transport_client_release().
Fixes: fce8a7bb5b ("PCI-Express Non-Transparent Bridge Support")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c3c796aca ]
A problem about ntb_hw_intel create debugfs failed is triggered with the
following log given:
[ 273.112733] Intel(R) PCI-E Non-Transparent Bridge Driver 2.0
[ 273.115342] debugfs: Directory 'ntb_hw_intel' with parent '/' already present!
The reason is that intel_ntb_pci_driver_init() returns
pci_register_driver() directly without checking its return value, if
pci_register_driver() failed, it returns without destroy the newly created
debugfs, resulting the debugfs of ntb_hw_intel can never be created later.
intel_ntb_pci_driver_init()
debugfs_create_dir() # create debugfs directory
pci_register_driver()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without destroy debugfs directory
Fix by removing debugfs when pci_register_driver() returns error.
Fixes: e26a5843f7 ("NTB: Split ntb_hw_intel and ntb_transport drivers")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98af0a33c1 ]
A problem about ntb_hw_amd create debugfs failed is triggered with the
following log given:
[ 618.431232] AMD(R) PCI-E Non-Transparent Bridge Driver 1.0
[ 618.433284] debugfs: Directory 'ntb_hw_amd' with parent '/' already present!
The reason is that amd_ntb_pci_driver_init() returns pci_register_driver()
directly without checking its return value, if pci_register_driver()
failed, it returns without destroy the newly created debugfs, resulting
the debugfs of ntb_hw_amd can never be created later.
amd_ntb_pci_driver_init()
debugfs_create_dir() # create debugfs directory
pci_register_driver()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without destroy debugfs directory
Fix by removing debugfs when pci_register_driver() returns error.
Fixes: a1b3695820 ("NTB: Add support for AMD PCI-Express Non-Transparent Bridge")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c012968259 ]
A problem about ntb_hw_idt create debugfs failed is triggered with the
following log given:
[ 1236.637636] IDT PCI-E Non-Transparent Bridge Driver 2.0
[ 1236.639292] debugfs: Directory 'ntb_hw_idt' with parent '/' already present!
The reason is that idt_pci_driver_init() returns pci_register_driver()
directly without checking its return value, if pci_register_driver()
failed, it returns without destroy the newly created debugfs, resulting
the debugfs of ntb_hw_idt can never be created later.
idt_pci_driver_init()
debugfs_create_dir() # create debugfs directory
pci_register_driver()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without destroy debugfs directory
Fix by removing debugfs when pci_register_driver() returns error.
Fixes: bf2a952d31 ("NTB: Add IDT 89HPESxNTx PCIe-switches support")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Support the below BAR configuration methods for epf NTB.
BAR 0: config and scratchpad
BAR 2: doorbell
BAR 4: memory map windows
Set difference BAR number information into struct ntb_epf_data. So difference
VID/PID can choose different BAR configurations. There are difference
BAR map method between epf NTB and epf vNTB Endpoint function.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Add Intel Granite Rapids NTB PCI device ID and related enabling.
Expectation is same hardware interface as Saphire Rapids Xeon platforms.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Allen Hubbe <allenbh@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The call to:
ret = simple_write_to_buffer(buf, size, offp, ubuf, size);
will return success if it is able to write even one byte to "buf".
The value of "*offp" controls which byte. This could result in
reading uninitialized data when we do the sscanf() on the next line.
This code is not really desigined to handle partial writes where
*offp is non-zero and the "buf" is preserved and re-used between writes.
Just ban partial writes and replace the simple_write_to_buffer() with
copy_from_user().
Fixes: 578b881ba9 ("NTB: Add tool test client")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
When building with Clang we encounter these warnings:
| drivers/ntb/hw/idt/ntb_hw_idt.c:2409:28: error: format specifies type
| 'unsigned char' but the argument has type 'int' [-Werror,-Wformat]
| "\t%hhu-%hhu.\t", idx + cnt - 1);
-
| drivers/ntb/hw/idt/ntb_hw_idt.c:2438:29: error: format specifies type
| 'unsigned char' but the argument has type 'int' [-Werror,-Wformat]
| "\t%hhu-%hhu.\t", idx + cnt - 1);
-
| drivers/ntb/hw/idt/ntb_hw_idt.c:2484:15: error: format specifies type
| 'unsigned char' but the argument has type 'int' [-Werror,-Wformat], src);
For the first two warnings the format specifier used is `%hhu` which
describes a u8. Both `idx` and `cnt` are u8 as well. However, the
expression as a whole is promoted to an int as you cannot get
smaller-than-int from addition. Therefore, to fix the warning, use the
promoted-to-type's format specifier -- in this case `%d`.
example:
``
uint8_t a = 4, b = 7;
int size = sizeof(a + b - 1);
printf("%d\n", size);
// output: 4
```
For the last warning, src is of type `int` while the format specifier
describes a u8. The fix here is just to use the proper specifier `%d`.
See more:
(https://wiki.sei.cmu.edu/confluence/display/c/INT02-C.+Understand+integer+conversion+rules)
"Integer types smaller than int are promoted when an operation is
performed on them. If all values of the original type can be represented
as an int, the value of the smaller type is converted to an int;
otherwise, it is converted to an unsigned int."
Link: https://github.com/ClangBuiltLinux/linux/issues/378
Signed-off-by: Justin Stitt <justinstitt@google.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The field offset for port configuration status on SPR has been changed to
bit 14 from ICX where it resides at bit 12. By chance link status detection
continued to work on SPR. This is due to bit 12 being a configuration bit
which is in sync with the status bit. Fix this by checking for a SPR device
and checking correct status bit.
Fixes: 26bfe3d0b2 ("ntb: intel: Add Icelake (gen4) support for Intel NTB")
Tested-by: Jerry Dai <jerry.dai@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Make use of the struct_size() helper instead of an open-coded version,
in order to avoid any potential type mistakes or integer overflows that,
in the worst scenario, could lead to heap overflows.
Also, address the following sparse warnings:
drivers/ntb/msi.c:46:23: warning: using sizeof on a flexible structure
Link: https://github.com/KSPP/linux/issues/174
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Pull NTB updates from Jon Mason:
"New AMD PCI ID for NTB, and a number of bug fixes for ntb_hw_switchtec
for Linux v5.17"
* tag 'ntb-5.17' of git://github.com/jonmason/ntb:
ntb_hw_switchtec: Fix a minor issue in config_req_id_table()
ntb_hw_switchtec: Remove code for disabling ID protection
ntb_hw_switchtec: Update the way of getting VEP instance ID
ntb_hw_switchtec: AND with the part_map for a valid tpart_vec
ntb_hw_switchtec: Fix bug with more than 32 partitions
ntb_hw_switchtec: Fix pff ioread to read into mmio_part_cfg_all
ntb_hw_switchtec: fix the spelling of "its"
NTB/msi: Fix ntbm_msi_request_threaded_irq() kernel-doc comment
ntb_hw_amd: Add NTB PCI ID for new gen CPU
The req_id_table_size field is 16-bit wide, use ioread16() to read the
value.
Signed-off-by: Kelvin Cao <kelvin.cao@microchip.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
ID protection is a firmware setting for NT window access control. With
it enabled, only the posted requests with requester IDs in the requester
ID table will be allowed to access the NT windows. Otherwise all posted
requests are allowed. Normally user will configure it statically via the
Switchtec config file, and it will take effect when the firmware boots
up. The driver can also toggle the ID protection setting dynamically,
which will overwrite the static setting in the Switchtec config file as
a side effect.
Currently, the driver disables the ID protection. However, it's not
necessary to disable the ID protection at the driver level as the driver
has already configured the proper requester IDs in the requester ID
table to allow the corresponding posted requests to hit the NT windows.
Remove the code that disables the ID protection to make the static
setting prevail.
Note: ID protection is not applicable to non-posted requests.
Signed-off-by: Kelvin Cao <kelvin.cao@microchip.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Gen4 firmware adds DMA VEP and NVMe VEP support in VEP (virtual EP)
instance ID register in addtion to management EP. Update the way of
getting management VEP instance ID.
Signed-off-by: Kelvin Cao <kelvin.cao@microchip.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Some firmware versions return 1 in the target partition vector for
undefined partitions. AND with the part_map to give a valid tpart_vec.
Signed-off-by: Jeremy Pallotta <jmpallotta@gmail.com>
Signed-off-by: Kelvin Cao <kelvin.cao@microchip.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Switchtec could support as mush as 48 partitions, but ffs & fls are
for 32 bit argument, in case of partition index larger than 31, the
current code could not parse the peer partition index correctly.
Change to the 64 bit version __ffs64 & fls64 accordingly to fix this
bug.
Fixes: 3df54c870f ("ntb_hw_switchtec: Allow using Switchtec NTB in multi-partition setups")
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
Signed-off-by: Kelvin Cao <kelvin.cao@microchip.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Array mmio_part_cfg_all holds the partition configuration of all
partitions, with partition number as index. Fix this by reading into
mmio_part_cfg_all for pff.
Fixes: 0ee28f26f3 ("NTB: switchtec_ntb: Add link management")
Signed-off-by: Jeremy Pallotta <jmpallotta@gmail.com>
Signed-off-by: Kelvin Cao <kelvin.cao@microchip.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Add the description of @msi_desc and change the @devname to @name
in ntbm_msi_request_threaded_irq() kernel-doc comment to remove
some warnings found by running scripts/kernel-doc, which is caused
by using 'make W=1'.
drivers/ntb/msi.c:285: warning: Function parameter or member 'name' not
described in 'ntbm_msi_request_threaded_irq'
drivers/ntb/msi.c:285: warning: Function parameter or member 'msi_desc'
not described in 'ntbm_msi_request_threaded_irq'
drivers/ntb/msi.c:285: warning: Excess function parameter 'devname'
description in 'ntbm_msi_request_threaded_irq'
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Pull NTB updates from Jon Mason:
"Bug fixes and clean-ups for Linux v5.15"
* tag 'ntb-5.15' of git://github.com/jonmason/ntb:
NTB: switch from 'pci_' to 'dma_' API
ntb: ntb_pingpong: remove redundant initialization of variables msg_data and spad_data
NTB: perf: Fix an error code in perf_setup_inbuf()
NTB: Fix an error code in ntb_msit_probe()
ntb: intel: remove invalid email address in header comment
The variables msg_data and spad_data are being initialized with values
that are never read, they are being updated later on. The initializations
are redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
When the function IS_ALIGNED() returns false, the value of ret is 0.
So, we set ret to -EINVAL to indicate this error.
Clean up smatch warning:
drivers/ntb/test/ntb_perf.c:602 perf_setup_inbuf() warn: missing error
code 'ret'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
When the value of nm->isr_ctx is false, the value of ret is 0.
So, we set ret to -ENOMEM to indicate this error.
Clean up smatch warning:
drivers/ntb/test/ntb_msi_test.c:373 ntb_msit_probe() warn: missing
error code 'ret'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Add support for EPF PCI Non-Transparent Bridge (NTB) devices. This driver
is platform independent and may be used by any platform that has multiple
PCI endpoint instances configured using the pci-epf-ntb driver. The driver
connnects to the standard NTB subsystem interface. The EPF NTB device has a
configurable number of memory windows (max 4), a configurable number of
doorbells (max 32), and a configurable number of scratch-pad registers.
Link: https://lore.kernel.org/r/20210201195809.7342-16-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Pull NTB fixes from Jon Mason:
"Bug fix for IDT NTB and Intel NTB LTR management support"
* tag 'ntb-5.11' of git://github.com/jonmason/ntb:
ntb: intel: add Intel NTB LTR vendor support for gen4 NTB
ntb: idt: fix error check in ntb_hw_idt.c
Intel NTB device has custom LTR management that is not compliant with the
PCIe standard. Add support to set LTR status triggered by link status
change.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Pull NTB fixes from Jon Mason.
* tag 'ntb-5.10' of git://github.com/jonmason/ntb:
NTB: Use struct_size() helper in devm_kzalloc()
ntb: intel: Fix memleak in intel_ntb_pci_probe
NTB: hw: amd: fix an issue about leak system resources
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes. Also, remove unnecessary
variable _struct_size_.
This code was detected with the help of Coccinelle and, audited and
fixed manually.
Addresses-KSPP-ID: https://github.com/KSPP/linux/issues/83
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
