[ Upstream commit f16d9fb6cf ]
Multiple applications may access the battery gauge at the same time, so
the gauge may be busy and EBUSY will be returned. The driver will set a
flag to record the EBUSY state, and this flag will be kept until the next
periodic update. When this flag is set, bq27xxx_battery_get_property()
will just return ENODEV until the flag is updated.
Even if the gauge was busy during the last accessing attempt, returning
ENODEV is not ideal, and can cause confusion in the applications layer.
Instead, retry accessing the I2C to update the flag is as expected, for
the gauge typically recovers from busy state within a few milliseconds.
If still failed to access the gauge, the real error code would be returned
instead of ENODEV (as suggested by Pali Rohár).
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Jerry Lv <Jerry.Lv@axis.com>
Link: https://lore.kernel.org/r/20250415-foo-fix-v2-1-5b45a395e4cc@axis.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30cc7b0d0e ]
The charge input threshold voltage register on the MAX77693 PMIC accepts
four values: 0x0 for 4.3v, 0x1 for 4.7v, 0x2 for 4.8v and 0x3 for 4.9v.
Due to an oversight, the driver calculated the values for 4.7v and above
starting from 0x0, rather than from 0x1 ([(4700000 - 4700000) / 100000]
gives 0).
Add 1 to the calculation to ensure that 4.7v is converted to a register
value of 0x1 and that the other two voltages are converted correctly as
well.
Fixes: 87c2d90678 ("power: max77693: Add charger driver for Maxim 77693")
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250316-max77693-charger-input-threshold-fix-v1-1-2b037d0ac722@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3fb3cb4350 ]
Size of variable sd_gain equals four bytes - DA9150_QIF_SD_GAIN_SIZE.
Size of variable shunt_val equals two bytes - DA9150_QIF_SHUNT_VAL_SIZE.
The expression sd_gain * shunt_val is currently being evaluated using
32-bit arithmetic. So during the multiplication an overflow may occur.
As the value of type 'u64' is used as storage for the eventual result, put
ULL variable at the first position of each expression in order to give the
compiler complete information about the proper arithmetic to use. According
to C99 the guaranteed width for a variable of type 'unsigned long long' >=
64 bits.
Remove the explicit cast to u64 as it is meaningless.
Just for the sake of consistency, perform the similar trick with another
expression concerning 'iavg'.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: a419b4fd91 ("power: Add support for DA9150 Fuel-Gauge")
Signed-off-by: Andrey Vatoropin <a.vatoropin@crpt.ru>
Link: https://lore.kernel.org/r/20250130090030.53422-1-a.vatoropin@crpt.ru
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6da4553ff ]
The put_device() call in power_supply_put() may call
power_supply_dev_release(). The latter function does not sleep so
power_supply_put() doesn't sleep either. Hence, remove the might_sleep()
call from power_supply_put(). This patch suppresses false positive
complaints about calling a sleeping function from atomic context if
power_supply_put() is called from atomic context.
Cc: Kyle Tso <kyletso@google.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Fixes: 1a352462b5 ("power_supply: Add power_supply_put for decrementing device reference counter")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240917193914.47566-1-bvanassche@acm.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e50a57d16f upstream.
Temp channel 0 aka temp1 can have a temp1_max_alarm attribute for
power_supply devices which have a POWER_SUPPLY_PROP_TEMP_ALERT_MAX
property.
HWMON_T_MAX_ALARM was missing from power_supply_hwmon_info for
temp channel 0, causing the hwmon temp1_max_alarm attribute to be
missing from such power_supply devices.
Add this to power_supply_hwmon_info to fix this.
Fixes: f1d33ae806 ("power: supply: remove duplicated argument in power_supply_hwmon_info")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240908185337.103696-2-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3a3acf839b ]
Commit 223a3b8283 ("power: supply: max17042_battery: use VFSOC for
capacity when no rsns") made it so that capacity on systems without
current sensing would be read from VFSOC instead of RepSOC. However,
the SOC threshold calculation still read RepSOC to get the SOC
regardless of the current sensing option state.
Fix this by applying the same conditional to determine which register
should be read.
This also seems to be the intended behavior as per the datasheet - SOC
alert config value in MiscCFG on setups without current sensing is set
to a value of 0b11, indicating SOC alerts being generated based on
VFSOC, instead of 0b00 which indicates SOC alerts being generated based
on RepSOC.
This fixes an issue on the Galaxy S3/Midas boards, where the alert
interrupt would be constantly retriggered, causing high CPU usage
on idle (around ~12%-15%).
Fixes: e5f3872d20 ("max17042: Add support for signalling change in SOC")
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240817-max17042-soc-threshold-fix-v1-1-72b45899c3cc@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e0fb11364 ]
The of_match shall correspond to the name of the regulator subnode,
or the deprecated `regulator-compatible` property must be used:
failing to do so, the regulator won't probe (and the driver will
as well not probe).
Since the devicetree binding for this driver is actually correct
and wants DTs to use the "usb-otg-vbus-regulator" subnode name,
fix this driver by aligning the `of_match` string to what the DT
binding wants.
Fixes: 0402e8ebb8 ("power: supply: mt6360_charger: add MT6360 charger support")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20240410084405.1389378-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 452d8950db ]
The rt9455_boost_voltage_values[] array is only used when USB PHY
support is enabled, causing a W=1 warning otherwise:
drivers/power/supply/rt9455_charger.c:200:18: error: 'rt9455_boost_voltage_values' defined but not used [-Werror=unused-const-variable=]
Enclose the definition in the same #ifdef as the references to it.
Fixes: e86d69dd78 ("power_supply: Add support for Richtek RT9455 battery charger")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240403080702.3509288-10-arnd@kernel.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2df70149e7 ]
The bq27xxx i2c-client may not have an IRQ, in which case
client->irq will be 0. bq27xxx_battery_i2c_probe() already has
an if (client->irq) check wrapping the request_threaded_irq().
But bq27xxx_battery_i2c_remove() unconditionally calls
free_irq(client->irq) leading to:
[ 190.310742] ------------[ cut here ]------------
[ 190.310843] Trying to free already-free IRQ 0
[ 190.310861] WARNING: CPU: 2 PID: 1304 at kernel/irq/manage.c:1893 free_irq+0x1b8/0x310
Followed by a backtrace when unbinding the driver. Add
an if (client->irq) to bq27xxx_battery_i2c_remove() mirroring
probe() to fix this.
Fixes: 444ff00734 ("power: supply: bq27xxx: Fix I2C IRQ race on remove")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240215155133.70537-1-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b55d073e65 ]
smatch complains that there is a buffer overflow and clang complains
'ret' is never read.
Smatch error:
drivers/power/supply/bq256xx_charger.c:1578 bq256xx_hw_init() error:
buffer overflow 'bq256xx_watchdog_time' 4 <= 4
Clang static checker:
Value stored to 'ret' is never read.
Add check for buffer overflow and error code from regmap_update_bits().
Fixes: 32e4978bb9 ("power: supply: bq256xx: Introduce the BQ256XX charger driver")
Signed-off-by: Su Hui <suhui@nfschina.com>
Link: https://lore.kernel.org/r/20231116041822.1378758-1-suhui@nfschina.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit dc77721ea4 upstream.
I had the following weird phenomena on a mobile phone: while
the capacity in /sys/class/power_supply/ab8500_fg/capacity
would reflect the actual charge and capacity of the battery,
only 1/3 of the value was shown on the battery status
indicator and warnings for low battery appeared.
It turns out that UPower, the Freedesktop power daemon,
will average all the power supplies of type "battery" in
/sys/class/power_supply/* if there is more than one battery.
For the AB8500, there was "battery" ab8500_fg, ab8500_btemp
and ab8500_chargalg. The latter two don't know anything
about the battery, and should not be considered. They were
however averaged and with the capacity of 0.
Flag ab8500_btemp and ab8500_chargalg with type "unknown"
so they are not averaged as batteries.
Remove the technology prop from ab8500_btemp as well, all
it does is snoop in on knowledge from another supply.
After this the battery indicator shows the right value.
Cc: Stefan Hansson <newbyte@disroot.org>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 95339f40a8 ]
The logic used for power_supply_is_system_supplied() counts all power
supplies and assumes that the system is running from AC if there is
either a non-battery power-supply reporting to be online or if no
power-supplies exist at all.
The second rule is for desktop systems, that don't have any
battery/charger devices. These systems will incorrectly report to be
powered from battery once a device scope power-supply is registered
(e.g. a HID device), since these power-supplies increase the counter.
Apart from HID devices, recent dGPUs provide UCSI power supplies on a
desktop systems. The dGPU by default doesn't have anything plugged in so
it's 'offline'. This makes power_supply_is_system_supplied() return 0
with a count of 1 meaning all drivers that use this get a wrong judgement.
To fix this case adjust the logic to also examine the scope of the power
supply. If the power supply is deemed a device power supply, then don't
count it.
Cc: Evan Quan <Evan.Quan@amd.com>
Suggested-by: Lijo Lazar <Lijo.Lazar@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 155c45a256 ]
Reduce the amount of output this dev_dbg() statement emits into logs,
otherwise if system software polls the sysfs entry for data and keeps
getting -ENODATA, it could end up filling the logs up.
This does in fact make systemd journald choke, since during boot the
sysfs power supply entries are polled and if journald starts at the
same time, the journal is just being repeatedly filled up, and the
system stops on trying to start journald without booting any further.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d5c129d6c ]
sc27xx_fgu_external_power_changed() dereferences data->battery,
which gets sets in ab8500_btemp_probe() like this:
data->battery = devm_power_supply_register(dev, &sc27xx_fgu_desc,
&fgu_cfg);
As soon as devm_power_supply_register() has called device_add()
the external_power_changed callback can get called. So there is a window
where sc27xx_fgu_external_power_changed() may get called while
data->battery has not been set yet leading to a NULL pointer dereference.
Fixing this is easy. The external_power_changed callback gets passed
the power_supply which will eventually get stored in data->battery,
so sc27xx_fgu_external_power_changed() can simply directly use
the passed in psy argument which is always valid.
After this change sc27xx_fgu_external_power_changed() is reduced to just
"power_supply_changed(psy);" and it has the same prototype. While at it
simply replace it with making the external_power_changed callback
directly point to power_supply_changed.
Cc: Orson Zhai <orsonzhai@gmail.com>
Cc: Chunyan Zhang <zhang.lyra@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5299ce4e9 ]
ab8500_btemp_external_power_changed() dereferences di->btemp_psy,
which gets sets in ab8500_btemp_probe() like this:
di->btemp_psy = devm_power_supply_register(dev, &ab8500_btemp_desc,
&psy_cfg);
As soon as devm_power_supply_register() has called device_add()
the external_power_changed callback can get called. So there is a window
where ab8500_btemp_external_power_changed() may get called while
di->btemp_psy has not been set yet leading to a NULL pointer dereference.
Fixing this is easy. The external_power_changed callback gets passed
the power_supply which will eventually get stored in di->btemp_psy,
so ab8500_btemp_external_power_changed() can simply directly use
the passed in psy argument which is always valid.
And the same applies to ab8500_fg_external_power_changed().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 77c2a3097d upstream.
The bq24192 model relies on external charger-type detection and once
that is done the bq24190_charger code will update the input current.
In this case, when the initial power_supply_changed() call is made
from the interrupt handler, the input settings are 5V/0.5A which
on many devices is not enough power to charge (while the device is on).
On many devices the fuel-gauge relies in its external_power_changed
callback to timely signal userspace about charging <-> discharging
status changes. Add a power_supply_changed() call after updating
the input current. This allows the fuel-gauge driver to timely recheck
if the battery is charging after the new input current has been applied
and then it can immediately notify userspace about this.
Fixes: 18f8e6f695 ("power: supply: bq24190_charger: Get input_current_limit from our supplier")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad3d9c779b upstream.
The bq25892 model relies on external charger-type detection and once
that is done the bq25890_charger code will update the input current
and if pumpexpress is used also the input voltage.
In this case, when the initial power_supply_changed() call is made
from the interrupt handler, the input settings are 5V/0.5A which
on many devices is not enough power to charge (while the device is on).
On many devices the fuel-gauge relies in its external_power_changed
callback to timely signal userspace about charging <-> discharging
status changes. Add a power_supply_changed() call after updating
the input current or voltage. This allows the fuel-gauge driver
to timely recheck if the battery is charging after the new input
settings have been applied and then it can immediately notify
userspace about this.
Fixes: 48f45b094d ("power: supply: bq25890: Support higher charging voltages through Pump Express+ protocol")
Fixes: eab25b4f93 ("power: supply: bq25890: On the bq25892 set the IINLIM based on external charger detection")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59a99cd462 upstream.
bq27xxx_external_power_changed() gets called when the charger is plugged
in or out. Rather then immediately scheduling an update wait 0.5 seconds
for things to stabilize, so that e.g. the (dis)charge current is stable
when bq27xxx_battery_update() runs.
Fixes: 740b755a3b ("bq27x00: Poll battery state")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 939a116142 upstream.
On gauges where the current register is signed, there is no charging
flag in the flags register. So only checking flags will not result
in power_supply_changed() getting called when e.g. a charger is plugged
in and the current sign changes from negative (discharging) to
positive (charging).
This causes userspace's notion of the status to lag until userspace
does a poll.
And when a power_supply_leds.c LED trigger is used to indicate charging
status with a LED, this LED will lag until the capacity percentage
changes, which may take many minutes (because the LED trigger only is
updated on power_supply_changed() calls).
Fix this by calling bq27xxx_battery_current_and_status() on gauges with
a signed current register and checking if the status has changed.
Fixes: 297a533b3e ("bq27x00: Cache battery registers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff4c4a2a44 upstream.
Move the bq27xxx_battery_update() functions to below
the bq27xxx_battery_current_and_status() function.
This is just moving a block of text, no functional changes.
This is a preparation patch for making bq27xxx_battery_update() check
the status and have it call power_supply_changed() on status changes.
Fixes: 297a533b3e ("bq27x00: Cache battery registers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 35092c5819 upstream.
Add a cache parameter to bq27xxx_battery_current_and_status() so that
it can optionally use cached flags instead of re-reading them itself.
This is a preparation patch for making bq27xxx_battery_update() check
the status and have it call power_supply_changed() on status changes.
Fixes: 297a533b3e ("bq27x00: Cache battery registers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c00bc80462 upstream.
Before this patch bq27xxx_battery_teardown() was setting poll_interval = 0
to avoid bq27xxx_battery_update() requeuing the delayed_work item.
There are 2 problems with this:
1. If the driver is unbound through sysfs, rather then the module being
rmmod-ed, this changes poll_interval unexpectedly
2. This is racy, after it being set poll_interval could be changed
before bq27xxx_battery_update() checks it through
/sys/module/bq27xxx_battery/parameters/poll_interval
Fix this by added a removed attribute to struct bq27xxx_device_info and
using that instead of setting poll_interval to 0.
There also is another poll_interval related race on remove(), writing
/sys/module/bq27xxx_battery/parameters/poll_interval will requeue
the delayed_work item for all devices on the bq27xxx_battery_devices
list and the device being removed was only removed from that list
after cancelling the delayed_work item.
Fix this by moving the removal from the bq27xxx_battery_devices list
to before cancelling the delayed_work item.
Fixes: 8cfaaa8118 ("bq27x00_battery: Fix OOPS caused by unregistring bq27x00 driver")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 444ff00734 upstream.
devm_request_threaded_irq() requested IRQs are only free-ed after
the driver's remove function has ran. So the IRQ could trigger and
call bq27xxx_battery_update() after bq27xxx_battery_teardown() has
already run.
Switch to explicitly free-ing the IRQ in bq27xxx_battery_i2c_remove()
to fix this.
Fixes: 8807feb91b ("power: bq27xxx_battery: Add interrupt handling support")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c34c0aef1 upstream.
bq27xxx_battery_update() assumes / requires that it is only run once,
not multiple times at the same time. But there are 3 possible callers:
1. bq27xxx_battery_poll() delayed_work item handler
2. bq27xxx_battery_irq_handler_thread() I2C IRQ handler
3. bq27xxx_battery_setup()
And there is no protection against these racing with each other,
fix this race condition by making all callers take di->lock:
- Rename bq27xxx_battery_update() to bq27xxx_battery_update_unlocked()
- Add new bq27xxx_battery_update() which takes di->lock and then calls
bq27xxx_battery_update_unlocked()
- Make stale cache check code in bq27xxx_battery_get_property(), which
already takes di->lock directly to check the jiffies, call
bq27xxx_battery_update_unlocked() instead of messing with
the delayed_work item
- Make bq27xxx_battery_update_unlocked() mod the delayed-work item
so that the next poll is delayed to poll_interval milliseconds after
the last update independent of the source of the update
Fixes: 740b755a3b ("bq27x00: Poll battery state")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e448464399 upstream.
When a battery's status changes from charging to full then
the charging-blink-full-solid trigger tries to change
the LED from blinking to solid/on.
As is documented in include/linux/leds.h to deactivate blinking /
to make the LED solid a LED_OFF must be send:
"""
* Deactivate blinking again when the brightness is set to LED_OFF
* via the brightness_set() callback.
"""
led_set_brighness() calls with a brightness value other then 0 / LED_OFF
merely change the brightness of the LED in its on state while it is
blinking.
So power_supply_update_bat_leds() must first send a LED_OFF event
before the LED_FULL to disable blinking.
Fixes: 6501f728c5 ("power_supply: Add new LED trigger charging-blink-solid-full")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 029a443b9b upstream.
bq25890_charger_external_power_changed() dereferences bq->charger,
which gets sets in bq25890_power_supply_init() like this:
bq->charger = devm_power_supply_register(bq->dev, &bq->desc, &psy_cfg);
As soon as devm_power_supply_register() has called device_add()
the external_power_changed callback can get called. So there is a window
where bq25890_charger_external_power_changed() may get called while
bq->charger has not been set yet leading to a NULL pointer dereference.
This race hits during boot sometimes on a Lenovo Yoga Book 1 yb1-x90f
when the cht_wcove_pwrsrc (extcon) power_supply is done with detecting
the connected charger-type which happens to exactly hit the small window:
BUG: kernel NULL pointer dereference, address: 0000000000000018
<snip>
RIP: 0010:__power_supply_is_supplied_by+0xb/0xb0
<snip>
Call Trace:
<TASK>
__power_supply_get_supplier_property+0x19/0x50
class_for_each_device+0xb1/0xe0
power_supply_get_property_from_supplier+0x2e/0x50
bq25890_charger_external_power_changed+0x38/0x1b0 [bq25890_charger]
__power_supply_changed_work+0x30/0x40
class_for_each_device+0xb1/0xe0
power_supply_changed_work+0x5f/0xe0
<snip>
Fixing this is easy. The external_power_changed callback gets passed
the power_supply which will eventually get stored in bq->charger,
so bq25890_charger_external_power_changed() can simply directly use
the passed in psy argument which is always valid.
Fixes: eab25b4f93 ("power: supply: bq25890: On the bq25892 set the IINLIM based on external charger detection")
Cc: stable@vger.kernel.org
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f8319774d6 upstream.
fuel_gauge_external_power_changed() dereferences info->bat,
which gets sets in axp288_fuel_gauge_probe() like this:
info->bat = devm_power_supply_register(dev, &fuel_gauge_desc, &psy_cfg);
As soon as devm_power_supply_register() has called device_add()
the external_power_changed callback can get called. So there is a window
where fuel_gauge_external_power_changed() may get called while
info->bat has not been set yet leading to a NULL pointer dereference.
Fixing this is easy. The external_power_changed callback gets passed
the power_supply which will eventually get stored in info->bat,
so fuel_gauge_external_power_changed() can simply directly use
the passed in psy argument which is always valid.
Fixes: 30abb3d079 ("power: supply: axp288_fuel_gauge: Take lock before updating the valid flag")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit baba1315a7 ]
When the SOC approaches zero, an integer overflows in the columb
counter causing the driver to react poorly. This makes the driver
think it's at (above) the fully charged capacity when in fact it's
zero. It would then write this full capacity to NVRAM which would be
used on boot if the device remained off for less than 5 hours and
not plugged in.
This can be fixed and guarded against by doing the following:
- Changing the type of tmp in rk817_read_or_set_full_charge_on_boot()
to be an int instead of a u32. That way we can account for negative
numbers.
- Guard against negative values for the full charge on boot by setting
the charge to 0 if the system charge reports less than 0.
- Catch scenarios where the battery voltage is below the design
minimum voltage and set the system SOC to 0 at that time and update
the columb counter with a charge level of 0.
- Change the off time value from 5 hours to 30 minutes before we
recalculate the current capacity based on the OCV tables.
These changes allow the driver to operate better at low voltage/low
capacity conditions.
Fixes: 3268a4d9b0 ("power: supply: rk817: Fix unsigned comparison with less than zero")
Fixes: 11cb8da018 ("power: supply: Add charger driver for Rockchip RK817")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44263f5006 ]
power-supply properties are reported in µV, µA and µW.
The IIO API provides mV, mA, mW, so the values need to
be multiplied by 1000.
Fixes: e60fea794e ("power: battery: Generic battery driver using IIO")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf6c880d5d ]
Variable 'pirq', which may receive negative value
in platform_get_irq().
Used as an index in a function regmap_irq_get_virq().
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Denis Arefev <arefev@swemel.ru>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
