[ Upstream commit 75d8d7a630 ]
ACLs that reside in the algorithmic TCAM (A-TCAM) in Spectrum-2 and
newer ASICs can share the same mask if their masks only differ in up to
8 consecutive bits. For example, consider the following filters:
# tc filter add dev swp1 ingress pref 1 proto ip flower dst_ip 192.0.2.0/24 action drop
# tc filter add dev swp1 ingress pref 1 proto ip flower dst_ip 198.51.100.128/25 action drop
The second filter can use the same mask as the first (dst_ip/24) with a
delta of 1 bit.
However, the above only works because the two filters have different
values in the common unmasked part (dst_ip/24). When entries have the
same value in the common unmasked part they create undesired collisions
in the device since many entries now have the same key. This leads to
firmware errors such as [1] and to a reduced scale.
Fix by adjusting the hash table key to only include the value in the
common unmasked part. That is, without including the delta bits. That
way the driver will detect the collision during filter insertion and
spill the filter into the circuit TCAM (C-TCAM).
Add a test case that fails without the fix and adjust existing cases
that check C-TCAM spillage according to the above limitation.
[1]
mlxsw_spectrum2 0000:06:00.0: EMAD reg access failed (tid=3379b18a00003394,reg_id=3027(ptce3),type=write,status=8(resource not available))
Fixes: c22291f7cf ("mlxsw: spectrum: acl: Implement delta for ERP")
Reported-by: Alexander Zubkov <green@qrator.net>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 483ae90d8f upstream.
When tc filters are first added to a net device, the corresponding local
port gets bound to an ACL group in the device. The group contains a list
of ACLs. In turn, each ACL points to a different TCAM region where the
filters are stored. During forwarding, the ACLs are sequentially
evaluated until a match is found.
One reason to place filters in different regions is when they are added
with decreasing priorities and in an alternating order so that two
consecutive filters can never fit in the same region because of their
key usage.
In Spectrum-2 and newer ASICs the firmware started to report that the
maximum number of ACLs in a group is more than 16, but the layout of the
register that configures ACL groups (PAGT) was not updated to account
for that. It is therefore possible to hit stack corruption [1] in the
rare case where more than 16 ACLs in a group are required.
Fix by limiting the maximum ACL group size to the minimum between what
the firmware reports and the maximum ACLs that fit in the PAGT register.
Add a test case to make sure the machine does not crash when this
condition is hit.
[1]
Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: mlxsw_sp_acl_tcam_group_update+0x116/0x120
[...]
dump_stack_lvl+0x36/0x50
panic+0x305/0x330
__stack_chk_fail+0x15/0x20
mlxsw_sp_acl_tcam_group_update+0x116/0x120
mlxsw_sp_acl_tcam_group_region_attach+0x69/0x110
mlxsw_sp_acl_tcam_vchunk_get+0x492/0xa20
mlxsw_sp_acl_tcam_ventry_add+0x25/0xe0
mlxsw_sp_acl_rule_add+0x47/0x240
mlxsw_sp_flower_replace+0x1a9/0x1d0
tc_setup_cb_add+0xdc/0x1c0
fl_hw_replace_filter+0x146/0x1f0
fl_change+0xc17/0x1360
tc_new_tfilter+0x472/0xb90
rtnetlink_rcv_msg+0x313/0x3b0
netlink_rcv_skb+0x58/0x100
netlink_unicast+0x244/0x390
netlink_sendmsg+0x1e4/0x440
____sys_sendmsg+0x164/0x260
___sys_sendmsg+0x9a/0xe0
__sys_sendmsg+0x7a/0xc0
do_syscall_64+0x40/0xe0
entry_SYSCALL_64_after_hwframe+0x63/0x6b
Fixes: c3ab435466 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Reported-by: Orel Hagag <orelh@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/2d91c89afba59c22587b444994ae419dbea8d876.1705502064.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8cc063ae1b ]
The purpose of the test_LAG_cleanup() function is to check that some
hardware addresses are removed from underlying devices after they have been
unenslaved. The test function simply checks that those addresses are not
present at the end. However, if the addresses were never added to begin
with due to some error in device setup, the test function currently passes.
This is a false positive since in that situation the test did not actually
exercise the intended functionality.
Add a check that the expected addresses are indeed present after device
setup. This makes the test function more robust.
I noticed this problem when running the team/dev_addr_lists.sh test on a
system without support for dummy and ipv6:
tools/testing/selftests/drivers/net/team# ./dev_addr_lists.sh
Error: Unknown device type.
Error: Unknown device type.
This program is not intended to be run as root.
RTNETLINK answers: Operation not supported
TEST: team cleanup mode lacp [ OK ]
Fixes: bbb774d921 ("net: Add tests for bonding and team address list management")
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Link: https://lore.kernel.org/r/20240131140848.360618-3-bpoirier@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b6fb3050d ]
Similar to commit dd2d40acdb ("selftests: bonding: Add more missing
config options"), add more networking-specific config options which are
needed for team device tests.
For testing, I used the minimal config generated by virtme-ng and I added
the options in the config file. Afterwards, the team device test passed.
Fixes: bbb774d921 ("net: Add tests for bonding and team address list management")
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Link: https://lore.kernel.org/r/20240131140848.360618-2-bpoirier@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b34f4de6d3 ]
'qos_pfc' test checks PFC behavior. The idea is to limit the traffic
using a shaper somewhere in the flow of the packets. In this area, the
buffer is smaller than the buffer at the beginning of the flow, so it fills
up until there is no more space left. The test configures there PFC
which is supposed to notice that the headroom is filling up and send PFC
Xoff to indicate the transmitter to stop sending traffic for the priorities
sharing this PG.
The Xon/Xoff threshold is auto-configured and always equal to
2*(MTU rounded up to cell size). Even after sending the PFC Xoff packet,
traffic will keep arriving until the transmitter receives and processes
the PFC packet. This amount of traffic is known as the PFC delay allowance.
Currently the buffer for the delay traffic is configured as 100KB. The
MTU in the test is 10KB, therefore the threshold for Xoff is about 20KB.
This allows 80KB extra to be stored in this buffer.
8-lane ports use two buffers among which the configured buffer is split,
the Xoff threshold then applies to each buffer in parallel.
The test does not take into account the behavior of 8-lane ports, when the
ports are configured to 400Gbps with 8 lanes or 800Gbps with 8 lanes,
packets are dropped and the test fails.
Check if the relevant ports use 8 lanes, in such case double the size of
the buffer, as the headroom is split half-half.
Cc: Shuah Khan <shuah@kernel.org>
Fixes: bfa804784e ("selftests: mlxsw: Add a PFC test")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/23ff11b7dff031eb04a41c0f5254a2b636cd8ebb.1705502064.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d6eeabcfa ]
Lately, a bug was found when many TC filters are added - at some point,
several bugs are printed to dmesg [1] and the switch is crashed with
segmentation fault.
The issue starts when gen_pool_free() fails because of unexpected
behavior - a try to free memory which is already freed, this leads to BUG()
call which crashes the switch and makes many other bugs.
Trying to track down the unexpected behavior led to a bug in eRP code. The
function mlxsw_sp_acl_erp_table_alloc() gets a pointer to the allocated
index, sets the value and returns an error code. When gen_pool_alloc()
fails it returns address 0, we track it and return -ENOBUFS outside, BUT
the call for gen_pool_alloc() already override the index in erp_table
structure. This is a problem when such allocation is done as part of
table expansion. This is not a new table, which will not be used in case
of allocation failure. We try to expand eRP table and override the
current index (non-zero) with zero. Then, it leads to an unexpected
behavior when address 0 is freed twice. Note that address 0 is valid in
erp_table->base_index and indeed other tables use it.
gen_pool_alloc() fails in case that there is no space left in the
pre-allocated pool, in our case, the pool is limited to
ACL_MAX_ERPT_BANK_SIZE, which is read from hardware. When more than max
erp entries are required, we exceed the limit and return an error, this
error leads to "Failed to migrate vregion" print.
Fix this by changing erp_table->base_index only in case of a successful
allocation.
Add a test case for such a scenario. Without this fix it causes
segmentation fault:
$ TESTS="max_erp_entries_test" ./tc_flower.sh
./tc_flower.sh: line 988: 1560 Segmentation fault tc filter del dev $h2 ingress chain $i protocol ip pref $i handle $j flower &>/dev/null
[1]:
kernel BUG at lib/genalloc.c:508!
invalid opcode: 0000 [#1] PREEMPT SMP
CPU: 6 PID: 3531 Comm: tc Not tainted 6.7.0-rc5-custom-ga6893f479f5e #1
Hardware name: Mellanox Technologies Ltd. MSN4700/VMOD0010, BIOS 5.11 07/12/2021
RIP: 0010:gen_pool_free_owner+0xc9/0xe0
...
Call Trace:
<TASK>
__mlxsw_sp_acl_erp_table_other_dec+0x70/0xa0 [mlxsw_spectrum]
mlxsw_sp_acl_erp_mask_destroy+0xf5/0x110 [mlxsw_spectrum]
objagg_obj_root_destroy+0x18/0x80 [objagg]
objagg_obj_destroy+0x12c/0x130 [objagg]
mlxsw_sp_acl_erp_mask_put+0x37/0x50 [mlxsw_spectrum]
mlxsw_sp_acl_ctcam_region_entry_remove+0x74/0xa0 [mlxsw_spectrum]
mlxsw_sp_acl_ctcam_entry_del+0x1e/0x40 [mlxsw_spectrum]
mlxsw_sp_acl_tcam_ventry_del+0x78/0xd0 [mlxsw_spectrum]
mlxsw_sp_flower_destroy+0x4d/0x70 [mlxsw_spectrum]
mlxsw_sp_flow_block_cb+0x73/0xb0 [mlxsw_spectrum]
tc_setup_cb_destroy+0xc1/0x180
fl_hw_destroy_filter+0x94/0xc0 [cls_flower]
__fl_delete+0x1ac/0x1c0 [cls_flower]
fl_destroy+0xc2/0x150 [cls_flower]
tcf_proto_destroy+0x1a/0xa0
...
mlxsw_spectrum3 0000:07:00.0: Failed to migrate vregion
mlxsw_spectrum3 0000:07:00.0: Failed to migrate vregion
Fixes: f465261aa1 ("mlxsw: spectrum_acl: Implement common eRP core")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/4cfca254dfc0e5d283974801a24371c7b6db5989.1705502064.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61fa2493ca ]
Similar to commit be80942465 ("selftests: bonding: do not set port down
before adding to bond"). The bond-arp-interval-causes-panic test failed
after commit a4abfa627c ("net: rtnetlink: Enslave device before bringing
it up") as the kernel will set the port down _after_ adding to bond if setting
port down specifically.
Fix it by removing the link down operation when adding to bond.
Fixes: 2ffd57327f ("selftests: bonding: cause oops in bond_rr_gen_slave_id")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Tested-by: Benjamin Poirier <benjamin.poirier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f922c7b1c1 ]
When devlink instance is put into network namespace and that network
namespace gets deleted, devlink instance is moved back into init_ns.
This is done as a part of cleanup_net() routine. Since cleanup_net()
is called asynchronously from workqueue, there is no guarantee that
the devlink instance move is done after "ip netns del" returns.
So fix this race by making sure that the devlink instance is present
before any other operation.
Reported-by: Amir Tzin <amirtz@nvidia.com>
Fixes: b74c37fd35 ("selftests: netdevsim: add tests for devlink reload with resources")
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20230220132336.198597-1-jiri@resnulli.us
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbb253b206 ]
We have two IS1 filters of the OCELOT_VCAP_KEY_ANY key type (the one with
"action vlan pop" and the one with "action vlan modify") and one of the
OCELOT_VCAP_KEY_IPV4 key type (the one with "action skbedit priority").
But we have no IS1 filter with the OCELOT_VCAP_KEY_ETYPE key type, and
there was an uncaught breakage there.
To increase test coverage, convert one of the OCELOT_VCAP_KEY_ANY
filters to OCELOT_VCAP_KEY_ETYPE, by making the filter also match on the
MAC SA of the traffic sent by mausezahn, $h1_mac.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230205192409.1796428-2-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2fc60e2ff9 ]
$number + > bash means redirect FD $number, e.g. commonly
used 2> redirects stderr (fd 2). The test uses 8192> to
write the number 8192 to a file, this results in:
./devlink.sh: line 499: 8192: Bad file descriptor
Oddly the test also papers over this issue by checking
for failure (expecting an error rather than success)
so it passes, anyway.
Fixes: ff18176ad8 ("selftests: Add a test of large binary to devlink health test")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
lag_lib.sh creates the interfaces dummy1 and dummy2 whereas
dev_addr_lists.sh:destroy() deletes the interfaces dummy0 and dummy1. Fix
the mismatch in names.
Fixes: bbb774d921 ("net: Add tests for bonding and team address list management")
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Reviewed-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When exporting and running a subset of selftests via kselftest, files from
parts of the source tree which were not exported are not available. A few
tests are trying to source such files. Address the problem by using
symlinks.
The problem can be reproduced by running:
make -C tools/testing/selftests gen_tar TARGETS="drivers/net/bonding"
[... extract archive ...]
./run_kselftest.sh
or:
make kselftest KBUILD_OUTPUT=/tmp/kselftests TARGETS="drivers/net/bonding"
Fixes: bbb774d921 ("net: Add tests for bonding and team address list management")
Fixes: eccd0a80dc ("selftests: net: dsa: add a stress test for unlocked FDB operations")
Link: https://lore.kernel.org/netdev/40f04ded-0c86-8669-24b1-9a313ca21076@redhat.com/
Reported-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Reviewed-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We can make the phc2sys helper not only synchronize a PHC to
CLOCK_REALTIME, which is what it currently does, but also CLOCK_REALTIME
to a PHC, which is going to be needed in distributed TSN tests.
Instead of making the complexity of the arguments passed to
phc2sys_start() explode, we can let it figure out the sync direction
automatically, based on ptp4l's port states.
Towards that goal, pass just the path to the desired ptp4l instance's
UNIX domain socket, and remove the $if_name argument (from which it
derives the PHC). Also adapt the one caller from the ocelot psfp.sh
test. In the case of psfp.sh, phc2sys_start is able to properly figure
out that CLOCK_REALTIME is the source clock and swp1's PHC is the
destination, because of the way in which ptp4l_start for the
UDS_ADDRESS_SWP1 was called: with slave_only=false, so it will always
win the BMCA and always become the sync master between itself and $h1.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It looks like this test has been accidentally dropped when resolving
conflicts in this Makefile.
Most probably because there were 3 different patches modifying this file
in parallel:
commit 152e8ec776 ("selftests/bonding: add a test for bonding lladdr target")
commit bbb774d921 ("net: Add tests for bonding and team address list management")
commit 2ffd57327f ("selftests: bonding: cause oops in bond_rr_gen_slave_id")
The first one was applied in 'net-next' while the two other ones were
recently applied in the 'net' tree.
But that's alright, easy to fix by re-adding the missing one!
Fixes: 0140a7168f ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net")
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Link: https://lore.kernel.org/r/20220923082306.2468081-1-matthieu.baerts@tessares.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This bonding selftest used to cause a kernel oops on aarch64
and should be architectures agnostic.
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is a regression test for commit 592335a416 ("bonding: accept
unsolicited NA message") and commit b7f14132bf ("bonding: use unspecified
address if no available link local address"). When the bond interface
up and no available link local address, unspecified address(::) is used to
send the NS message. The unsolicited NA message should also be accepted
for validation.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Link: https://lore.kernel.org/r/20220920033047.173244-1-liuhangbin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The previous patch added a test which can be used instead of qos_burst.sh.
Remove this test.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add an equivalent test to qos_burst, the test's purpose is same, but the
new test uses simpler topology and does not require forcing low speed.
In addition, it can be run Spectrum-2 and not only Spectrum-3+. The idea
is to use a shaper in order to limit the traffic and create congestion.
qos_burst test uses small pool, sends many small packets, and verify that
packets are not dropped, which means that many descriptors can be handled.
This test should check the change that commit c864769add
("mlxsw: Configure descriptor buffers") pushed.
Instead, the new test tries to use more than 85% of maximum supported
descriptors. The idea is to use big pool (as much as the ASIC supports),
such that the pool size does not limit the traffic, then send many small
packets, which means that many descriptors are used, and check how many
packets the switch can handle.
The usage of shaper allows to run the test in all ASICs, regardless of
the CPU abilities, as it is able to create the congestion with low rate
of packets.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
QOS tests create congestion and verify the switch behavior. To create
congestion, they need to have more traffic than the port can handle, so
some of them force 1Gbps speed.
The tests assume that 1Gbps speed is supported, otherwise, they will fail.
Spectrum-4 ASIC will not support this speed in all ports, so to be able
to run the tests there, some adjustments are required. Use shapers to limit
the traffic instead of forcing speed. Note that for several ports, the
speed configuration is just for autoneg issues, so shaper is not needed
instead.
The tests already use ETS qdisc as a root and RED qdiscs as children. Add
a new TBF shaper to limit the rate of traffic, and use it as a root qdisc,
then save the previous hierarchy of qdiscs under the new TBF root.
In some ASICs, the shapers do not limit the traffic as accurately as
forcing speed. To make the tests stable, allow the backlog size to be up to
+-10% of the threshold. The aim of the tests is to make sure that with
backlog << threshold, there are no drops, and that packets are dropped
somewhere in vicinity of the configured threshold.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
QOS tests create congestion and verify the switch behavior. To create
congestion, they need to have more traffic than the port can handle, so
some of them force 1Gbps speed.
The tests assume that 1Gbps speed is supported, otherwise, they will fail.
Spectrum-4 ASIC will not support this speed in all ports, so to be able
to run QOS tests there, some adjustments are required. Use shapers to
limit the traffic instead of forcing speed. Note that for several ports,
the speed configuration is just for autoneg issues, so shaper is not needed
instead.
In tests that already use shapers, set the existing shaper to be a child of
a new TBF shaper which is added as a root qdisc and acts as a port shaper.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Test that the bonding and team drivers clean up an underlying device's
address lists (dev->uc, dev->mc) when the aggregated device is deleted.
Test addition and removal of the LACPDU multicast address on underlying
devices by the bonding driver.
v2:
* add lag_lib.sh to TEST_FILES
v3:
* extend bond_listen_lacpdu_multicast test to init_state up and down cases
* remove some superfluous shell syntax and 'set dev ... up' commands
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This has been validated on the Ocelot/Felix switch family (NXP LS1028A)
and should be relevant to any switch driver that offloads the tc-flower
and/or tc-matchall actions trap, drop, accept, mirred, for which DSA has
operations.
TEST: gact drop and ok (skip_hw) [ OK ]
TEST: mirred egress flower redirect (skip_hw) [ OK ]
TEST: mirred egress flower mirror (skip_hw) [ OK ]
TEST: mirred egress matchall mirror (skip_hw) [ OK ]
TEST: mirred_egress_to_ingress (skip_hw) [ OK ]
TEST: gact drop and ok (skip_sw) [ OK ]
TEST: mirred egress flower redirect (skip_sw) [ OK ]
TEST: mirred egress flower mirror (skip_sw) [ OK ]
TEST: mirred egress matchall mirror (skip_sw) [ OK ]
TEST: trap (skip_sw) [ OK ]
TEST: mirred_egress_to_ingress (skip_sw) [ OK ]
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220831170839.931184-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This creates a test collection in drivers/net/bonding for bonding
specific kernel selftests.
The first test is a reproducer that provisions a bond and given the
specific order in how the ip-link(8) commands are issued the bond never
transmits an LACPDU frame on any of its slaves.
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After routing, the device always consults a table that determines the
packet's egress VID based on {egress RIF, egress local port}. In the
unified bridge model, it is up to software to maintain this table via
REIV register.
The table needs to be updated in the following flows:
1. When a RIF is set on a FID, for each FID's {Port, VID} mapping, a new
{RIF, Port}->VID mapping should be created.
2. When a {Port, VID} is mapped to a FID and the FID already has a RIF,
a new {RIF, Port}->VID mapping should be created.
Add a test to verify that packets get the correct VID after routing,
regardless of the order of the configuration.
# ./egress_vid_classification.sh
TEST: Add RIF for existing {port, VID}->FID mapping [ OK ]
TEST: Add {port, VID}->FID mapping for FID with a RIF [ OK ]
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before layer 2 forwarding, the device classifies an incoming packet to a
FID. After classification, the FID is known, but also all the attributes of
the FID, such as the router interface (RIF) via which a packet that needs
to be routed will ingress the router block.
For VXLAN decapsulation, the FID classification is done according to the
VNI. When a RIF is added on top of a FID, the existing VNI->FID mapping
should be updated by the software with the new RIF. In addition, when a new
mapping is added for FID which already has a RIF, the correct RIF should
be used for it.
Add a test to verify that packets can be routed after decapsulation which
is done after VNI->FID classification, regardless of the order of the
configuration.
# ./ingress_rif_conf_vxlan.sh
TEST: Add RIF for existing VNI->FID mapping [ OK ]
TEST: Add VNI->FID mapping for FID with a RIF [ OK ]
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before layer 2 forwarding, the device classifies an incoming packet to a
FID. After classification, the FID is known, but also all the attributes of
the FID, such as the router interface (RIF) via which a packet that needs
to be routed will ingress the router block.
For VLAN-aware bridges (802.1Q), the FID classification is done according
to VID. When a RIF is added on top of a FID, the existing VID->FID mapping
should be updated by the software with the new RIF.
We never map multiple VLANs to the same FID using VID->FID, so we cannot
create VID->FID for FID which already has a RIF using 802.1Q. Anyway,
verify that packets can be routed via port which is added after the FID
already has a RIF.
Add a test to verify that packets can be routed after VID->FID
classification, regardless of the order of the configuration.
# ./ingress_rif_conf_1q.sh
TEST: Add RIF for existing VID->FID mapping [ OK ]
TEST: Add port to VID->FID mapping for FID with a RIF [ OK ]
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before layer 2 forwarding, the device classifies an incoming packet to a
FID. After classification, the FID is known, but also all the attributes of
the FID, such as the router interface (RIF) via which a packet that needs
to be routed will ingress the router block.
For VLAN-unaware bridges (802.1D), the FID classification is done according
to {Port, VID}. When a RIF is added on top of a FID, all the existing
{Port, VID}->FID mappings should be updated by the software with the new
RIF. In addition, when a new mapping is added for FID which already has a
RIF, the correct RIF should be used for it.
Add a test to verify that packets can be routed after {Port, VID}->FID
classification, regardless of the order of the configuration.
# ./ingress_rif_conf_1d.sh
TEST: Add RIF for existing {port, VID}->FID mapping [ OK ]
TEST: Add {port, VID}->FID mapping for FID with a RIF [ OK ]
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking changes from Paolo Abeni:
"Core:
- Refactor the forward memory allocation to better cope with memory
pressure with many open sockets, moving from a per socket cache to
a per-CPU one
- Replace rwlocks with RCU for better fairness in ping, raw sockets
and IP multicast router.
- Network-side support for IO uring zero-copy send.
- A few skb drop reason improvements, including codegen the source
file with string mapping instead of using macro magic.
- Rename reference tracking helpers to a more consistent netdev_*
schema.
- Adapt u64_stats_t type to address load/store tearing issues.
- Refine debug helper usage to reduce the log noise caused by bots.
BPF:
- Improve socket map performance, avoiding skb cloning on read
operation.
- Add support for 64 bits enum, to match types exposed by kernel.
- Introduce support for sleepable uprobes program.
- Introduce support for enum textual representation in libbpf.
- New helpers to implement synproxy with eBPF/XDP.
- Improve loop performances, inlining indirect calls when possible.
- Removed all the deprecated libbpf APIs.
- Implement new eBPF-based LSM flavor.
- Add type match support, which allow accurate queries to the eBPF
used types.
- A few TCP congetsion control framework usability improvements.
- Add new infrastructure to manipulate CT entries via eBPF programs.
- Allow for livepatch (KLP) and BPF trampolines to attach to the same
kernel function.
Protocols:
- Introduce per network namespace lookup tables for unix sockets,
increasing scalability and reducing contention.
- Preparation work for Wi-Fi 7 Multi-Link Operation (MLO) support.
- Add support to forciby close TIME_WAIT TCP sockets via user-space
tools.
- Significant performance improvement for the TLS 1.3 receive path,
both for zero-copy and not-zero-copy.
- Support for changing the initial MTPCP subflow priority/backup
status
- Introduce virtually contingus buffers for sockets over RDMA, to
cope better with memory pressure.
- Extend CAN ethtool support with timestamping capabilities
- Refactor CAN build infrastructure to allow building only the needed
features.
Driver API:
- Remove devlink mutex to allow parallel commands on multiple links.
- Add support for pause stats in distributed switch.
- Implement devlink helpers to query and flash line cards.
- New helper for phy mode to register conversion.
New hardware / drivers:
- Ethernet DSA driver for the rockchip mt7531 on BPI-R2 Pro.
- Ethernet DSA driver for the Renesas RZ/N1 A5PSW switch.
- Ethernet DSA driver for the Microchip LAN937x switch.
- Ethernet PHY driver for the Aquantia AQR113C EPHY.
- CAN driver for the OBD-II ELM327 interface.
- CAN driver for RZ/N1 SJA1000 CAN controller.
- Bluetooth: Infineon CYW55572 Wi-Fi plus Bluetooth combo device.
Drivers:
- Intel Ethernet NICs:
- i40e: add support for vlan pruning
- i40e: add support for XDP framented packets
- ice: improved vlan offload support
- ice: add support for PPPoE offload
- Mellanox Ethernet (mlx5)
- refactor packet steering offload for performance and scalability
- extend support for TC offload
- refactor devlink code to clean-up the locking schema
- support stacked vlans for bridge offloads
- use TLS objects pool to improve connection rate
- Netronome Ethernet NICs (nfp):
- extend support for IPv6 fields mangling offload
- add support for vepa mode in HW bridge
- better support for virtio data path acceleration (VDPA)
- enable TSO by default
- Microsoft vNIC driver (mana)
- add support for XDP redirect
- Others Ethernet drivers:
- bonding: add per-port priority support
- microchip lan743x: extend phy support
- Fungible funeth: support UDP segmentation offload and XDP xmit
- Solarflare EF100: add support for virtual function representors
- MediaTek SoC: add XDP support
- Mellanox Ethernet/IB switch (mlxsw):
- dropped support for unreleased H/W (XM router).
- improved stats accuracy
- unified bridge model coversion improving scalability (parts 1-6)
- support for PTP in Spectrum-2 asics
- Broadcom PHYs
- add PTP support for BCM54210E
- add support for the BCM53128 internal PHY
- Marvell Ethernet switches (prestera):
- implement support for multicast forwarding offload
- Embedded Ethernet switches:
- refactor OcteonTx MAC filter for better scalability
- improve TC H/W offload for the Felix driver
- refactor the Microchip ksz8 and ksz9477 drivers to share the
probe code (parts 1, 2), add support for phylink mac
configuration
- Other WiFi:
- Microchip wilc1000: diable WEP support and enable WPA3
- Atheros ath10k: encapsulation offload support
Old code removal:
- Neterion vxge ethernet driver: this is untouched since more than 10 years"
* tag 'net-next-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1890 commits)
doc: sfp-phylink: Fix a broken reference
wireguard: selftests: support UML
wireguard: allowedips: don't corrupt stack when detecting overflow
wireguard: selftests: update config fragments
wireguard: ratelimiter: use hrtimer in selftest
net/mlx5e: xsk: Discard unaligned XSK frames on striding RQ
net: usb: ax88179_178a: Bind only to vendor-specific interface
selftests: net: fix IOAM test skip return code
net: usb: make USB_RTL8153_ECM non user configurable
net: marvell: prestera: remove reduntant code
octeontx2-pf: Reduce minimum mtu size to 60
net: devlink: Fix missing mutex_unlock() call
net/tls: Remove redundant workqueue flush before destroy
net: txgbe: Fix an error handling path in txgbe_probe()
net: dsa: Fix spelling mistakes and cleanup code
Documentation: devlink: add add devlink-selftests to the table of contents
dccp: put dccp_qpolicy_full() and dccp_qpolicy_push() in the same lock
net: ionic: fix error check for vlan flags in ionic_set_nic_features()
net: ice: fix error NETIF_F_HW_VLAN_CTAG_FILTER check in ice_vsi_sync_fltr()
nfp: flower: add support for tunnel offload without key ID
...
Add IPv4 and IPv6 test cases that ensure that we are not leaking a
reference on the nexthop device when we are unable to delete its
associated route.
Without the fix in a previous patch ("netdevsim: fib: Fix reference
count leak on route deletion failure") both test cases get stuck,
waiting for the reference to be released from the dummy device [1][2].
[1]
unregister_netdevice: waiting for dummy1 to become free. Usage count = 5
leaked reference.
fib_check_nh+0x275/0x620
fib_create_info+0x237c/0x4d30
fib_table_insert+0x1dd/0x1d20
inet_rtm_newroute+0x11b/0x200
rtnetlink_rcv_msg+0x43b/0xd20
netlink_rcv_skb+0x15e/0x430
netlink_unicast+0x53b/0x800
netlink_sendmsg+0x945/0xe40
____sys_sendmsg+0x747/0x960
___sys_sendmsg+0x11d/0x190
__sys_sendmsg+0x118/0x1e0
do_syscall_64+0x34/0x80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
[2]
unregister_netdevice: waiting for dummy1 to become free. Usage count = 5
leaked reference.
fib6_nh_init+0xc46/0x1ca0
ip6_route_info_create+0x1167/0x19a0
ip6_route_add+0x27/0x150
inet6_rtm_newroute+0x161/0x170
rtnetlink_rcv_msg+0x43b/0xd20
netlink_rcv_skb+0x15e/0x430
netlink_unicast+0x53b/0x800
netlink_sendmsg+0x945/0xe40
____sys_sendmsg+0x747/0x960
___sys_sendmsg+0x11d/0x190
__sys_sendmsg+0x118/0x1e0
do_syscall_64+0x34/0x80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once line card is activated, check the FW version and PSID are exposed.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Once line card is provisioned, check if HW revision and INI version
are exposed on associated nested auxiliary device.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stop using the KSFT_KHDR_INSTALL flag as installing the kernel headers
from the kselftest Makefile is causing some issues. Instead, rely on
the headers to be installed directly by the top-level Makefile
"headers_install" make target prior to building kselftest.
Signed-off-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Selftest udmabuf for the dma-buf driver is skipped when the device file
(e.g. /dev/udmabuf) for the DMA buffer cannot be opened i.e. no DMA buffer
has been allocated.
This patch adds clarity to the SKIP message.
Signed-off-by: Soumya Negi <soumya.negi97@gmail.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Add error messages when the module test-drm_mm is not found or could
not be removed to make tests output more readable.
Signed-off-by: Gautam Menghani <gautammenghani201@gmail.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Instead of hard coding the scale target in the test, dynamically set it
based on the maximum number of flow counters and their current
occupancy.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This tests creates as many RIFs as possible, ideally more than there can be
RIF counters (though that is currently only possible on Spectrum-1). It
then tries to enable L3 HW stats on each of the RIFs. It also contains the
traffic test, which tries to run traffic through a log2 of those counters
and checks that the traffic is shown in the counter values.
Like with tc_flower traffic test, take a log2 subset of rules. The logic
behind picking log2 rules is that then every bit of the instantiated item's
number is exercised. This should catch issues whether they happen at the
high end, low end, or somewhere in between.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test that checks that the created filters do actually trigger on
matching traffic.
Exercising all the rules would be a very lengthy process. Instead, take a
log2 subset of rules. The logic behind picking log2 rules is that then
every bit of the instantiated item's number is exercised. This should catch
issues whether they happen at the high end, low end, or somewhere in
between.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scale tests are verifying behavior of mlxsw when number of instances of
some resource reaches the ASIC capacity. The number of instances is
referred to as "target" number.
No scale tests so far needed to know this target number to clean up. E.g.
the tc_flower simply removes the clsact qdisc that all the tested filters
are hooked onto, and that takes care of collecting all the filters.
However, for the RIF counter test, which is being added in a future patch,
VLAN netdevices are created. These are created as part of the test, but of
course the cleanup needs to undo them again. For that it needs to know how
many there were. To support this usage, pass the target number to the
cleanup callback.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski
Danielle Ratson
Ido Schimmel
Benjamin Poirier
Amit Cohen
Hangbin Liu
Mathieu Desnoyers
Jiri Pirko
Vladimir Oltean
Matthieu Baerts
Jonathan Toppins
Linus Torvalds
Paolo Abeni
Martin Blumenstingl
Guillaume Tucker
Soumya Negi
Gautam Menghani
Petr Machata