[ Upstream commit 66aad7d8d3 ]
In ACM support for sending breaks to devices is optional.
If a device says that it doenot support sending breaks,
the host must respect that.
Given the number of optional features providing tty operations
for each combination is not practical and errors need to be
returned dynamically if unsupported features are requested.
In case a device does not support break, we want the tty layer
to treat that like it treats drivers that statically cannot
support sending a break. It ignores the inability and does nothing.
This patch uses EOPNOTSUPP to indicate that.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 9e98966c7b ("tty: rework break handling")
Link: https://lore.kernel.org/r/20231207132639.18250-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66619686d1 ]
If the driver sets TTY_DRIVER_HARDWARE_BREAK, we leave ops->break_ctl()
to the driver and return from send_break(). But we do it using a local
variable and keep the code flowing through the end of the function.
Instead, do 'return' immediately with the ops->break_ctl()'s return
value.
This way, we don't have to stuff the 'else' branch of the 'if' with the
software break handling. And we can re-indent the function too.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230919085156.1578-14-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 66aad7d8d3 ("usb: cdc-acm: return correct error code on unsupported break")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78d60dae9a ]
When using the serial port as RS485 port, the tx statemachine is used to
control the RTS pin to drive the RS485 transceiver TX_EN pin. When the
TTY port is closed in the middle of a transmission (for instance during
userland application crash), imx_uart_shutdown disables the interface
and disables the Transmission Complete interrupt. afer that,
imx_uart_stop_tx bails on an incomplete transmission, to be retriggered
by the TC interrupt. This interrupt is disabled and therefore the tx
statemachine never transitions out of SEND. The statemachine is in
deadlock now, and the TX_EN remains low, making the interface useless.
imx_uart_stop_tx now checks for incomplete transmission AND whether TC
interrupts are enabled before bailing to be retriggered. This makes sure
the state machine handling is reached, and is properly set to
WAIT_AFTER_SEND.
Fixes: cb1a609236 ("serial: imx: implement rts delaying for rs485")
Signed-off-by: Paul Geurts <paul_geurts@live.nl>
Tested-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Tested-by: Eberhard Stoll <eberhard.stoll@gmx.de>
Link: https://lore.kernel.org/r/AM0PR09MB26758F651BC1B742EB45775995B8A@AM0PR09MB2675.eurprd09.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad90d0358b ]
Returning an error code from .remove() makes the driver core emit the
little helpful error message:
remove callback returned a non-zero value. This will be ignored.
and then remove the device anyhow. So all resources that were not freed
are leaked in this case. Skipping serial8250_unregister_port() has the
potential to keep enough of the UART around to trigger a use-after-free.
So replace the error return (and with it the little helpful error
message) by a more useful error message and continue to cleanup.
Fixes: e3f0c638f4 ("serial: 8250: omap: Fix unpaired pm_runtime_put_sync() in omap8250_remove()")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20231110152927.70601-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6d710b769c upstream.
The original comment is confusing because it implies that variants other
than the SC16IS762 supports other SPI modes beside SPI_MODE_0.
Extract from datasheet:
The SC16IS762 differs from the SC16IS752 in that it supports SPI clock
speeds up to 15 Mbit/s instead of the 4 Mbit/s supported by the
SC16IS752... In all other aspects, the SC16IS762 is functionally and
electrically the same as the SC16IS752.
The same is also true of the SC16IS760 variant versus the SC16IS740 and
SC16IS750 variants.
For all variants, only SPI mode 0 is supported.
Change comment and abort probing if the specified SPI mode is not
SPI_MODE_0.
Fixes: 2c837a8a8f ("sc16is7xx: spi interface is added")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c45eaa813 upstream.
There are register accesses in the function imx_uart_rs485_config(). The
clock must be enabled for these accesses. This was ensured by calling it
via the function uart_rs485_config() in the probe() function within the
range where the clock is enabled. With the commit 7c7f9bc986 ("serial:
Deassert Transmit Enable on probe in driver-specific way") it was removed
from the probe() function and is now only called through the function
uart_add_one_port() which is located at the end of the probe() function.
But the clock is already switched off in this area. To ensure that the
clock is enabled during register access, move the disabling of the clock
to the very end of the probe() function. To avoid leaking enabled clocks
on error also add an error path for exiting with disabling the clock.
Fixes: 7c7f9bc986 ("serial: Deassert Transmit Enable on probe in driver-specific way")
Cc: stable <stable@kernel.org>
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/20231226113647.39376-1-cniedermaier@dh-electronics.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08ce9a1b72 upstream.
This device has a silicon bug that makes it report a timeout interrupt
but no data in the FIFO.
The datasheet states the following in the errata section 18.1.4:
"If the host reads the receive FIFO at the same time as a
time-out interrupt condition happens, the host might read 0xCC
(time-out) in the Interrupt Indication Register (IIR), but bit 0
of the Line Status Register (LSR) is not set (means there is no
data in the receive FIFO)."
The errata description seems to indicate it concerns only polled mode of
operation when reading bit 0 of the LSR register. However, tests have
shown and NXP has confirmed that the RXLVL register also yields 0 when
the bug is triggered, and hence the IRQ driven implementation in this
driver is equally affected.
This bug has hit us on production units and when it does, sc16is7xx_irq()
would spin forever because sc16is7xx_port_irq() keeps seeing an
interrupt in the IIR register that is not cleared because the driver
does not call into sc16is7xx_handle_rx() unless the RXLVL register
reports at least one byte in the FIFO.
Fix this by always reading one byte from the FIFO when this condition
is detected in order to clear the interrupt. This approach was
confirmed to be correct by NXP through their support channels.
Tested by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Daniel Mack <daniel@zonque.org>
Co-Developed-by: Maxim Popov <maxim.snafu@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231123072818.1394539-1-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5b68061983 ]
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211224142917.6966-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 2a1d728f20 ("tty: serial: meson: fix hard LOCKUP on crtscts mode")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ef5dd8ec88 upstream.
The xencons_connect_backend() function allocates a local interdomain
event channel with xenbus_alloc_evtchn(), then calls
bind_interdomain_evtchn_to_irq_lateeoi() to bind to that port# on the
*remote* domain.
That doesn't work very well:
(qemu) device_add xen-console,id=con1,chardev=pty0
[ 44.323872] xenconsole console-1: 2 xenbus_dev_probe on device/console/1
[ 44.323995] xenconsole: probe of console-1 failed with error -2
Fix it to use bind_evtchn_to_irq_lateeoi(), which does the right thing
by just binding that *local* event channel to an irq. The backend will
do the interdomain binding.
This didn't affect the primary console because the setup for that is
special — the toolstack allocates the guest event channel and the guest
discovers it with HVMOP_get_param.
Fixes: fe415186b4 ("xen/console: harden hvc_xen against event channel storms")
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231020161529.355083-2-dwmw2@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a30badfd7c upstream.
On unplug of a Xen console, xencons_disconnect_backend() unconditionally
calls free_irq() via unbind_from_irqhandler(), causing a warning of
freeing an already-free IRQ:
(qemu) device_del con1
[ 32.050919] ------------[ cut here ]------------
[ 32.050942] Trying to free already-free IRQ 33
[ 32.050990] WARNING: CPU: 0 PID: 51 at kernel/irq/manage.c:1895 __free_irq+0x1d4/0x330
It should be using evtchn_put() to tear down the event channel binding,
and let the Linux IRQ side of it be handled by notifier_del_irq() through
the HVC code.
On which topic... xencons_disconnect_backend() should call hvc_remove()
*first*, rather than tearing down the event channel and grant mapping
while they are in use. And then the IRQ is guaranteed to be freed by
the time it's torn down by evtchn_put().
Since evtchn_put() also closes the actual event channel, avoid calling
xenbus_free_evtchn() except in the failure path where the IRQ was not
successfully set up.
However, calling hvc_remove() at the start of xencons_disconnect_backend()
still isn't early enough. An unplug request is indicated by the backend
setting its state to XenbusStateClosing, which triggers a notification
to xencons_backend_changed(), which... does nothing except set its own
frontend state directly to XenbusStateClosed without *actually* tearing
down the HVC device or, you know, making sure it isn't actively in use.
So the backend sees the guest frontend set its state to XenbusStateClosed
and stops servicing the interrupt... and the guest spins for ever in the
domU_write_console() function waiting for the ring to drain.
Fix that one by calling hvc_remove() from xencons_backend_changed() before
signalling to the backend that it's OK to proceed with the removal.
Tested with 'dd if=/dev/zero of=/dev/hvc1' while telling Qemu to remove
the console device.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231020161529.355083-4-dwmw2@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd976a97d1 upstream.
The smp_processor_id() shouldn't be called from preemptible code.
Instead use get_cpu() and put_cpu() which disables preemption in
addition to getting the processor id. Enable preemption back after
calling schedule_work() to make sure that the work gets scheduled on all
cores other than the current core. We want to avoid a scenario where
current core's stack trace is printed multiple times and one core's
stack trace isn't printed because of scheduling of current task.
This fixes the following bug:
[ 119.143590] sysrq: Show backtrace of all active CPUs
[ 119.143902] BUG: using smp_processor_id() in preemptible [00000000] code: bash/873
[ 119.144586] caller is debug_smp_processor_id+0x20/0x30
[ 119.144827] CPU: 6 PID: 873 Comm: bash Not tainted 5.10.124-dirty #3
[ 119.144861] Hardware name: QEMU QEMU Virtual Machine, BIOS 2023.05-1 07/22/2023
[ 119.145053] Call trace:
[ 119.145093] dump_backtrace+0x0/0x1a0
[ 119.145122] show_stack+0x18/0x70
[ 119.145141] dump_stack+0xc4/0x11c
[ 119.145159] check_preemption_disabled+0x100/0x110
[ 119.145175] debug_smp_processor_id+0x20/0x30
[ 119.145195] sysrq_handle_showallcpus+0x20/0xc0
[ 119.145211] __handle_sysrq+0x8c/0x1a0
[ 119.145227] write_sysrq_trigger+0x94/0x12c
[ 119.145247] proc_reg_write+0xa8/0xe4
[ 119.145266] vfs_write+0xec/0x280
[ 119.145282] ksys_write+0x6c/0x100
[ 119.145298] __arm64_sys_write+0x20/0x30
[ 119.145315] el0_svc_common.constprop.0+0x78/0x1e4
[ 119.145332] do_el0_svc+0x24/0x8c
[ 119.145348] el0_svc+0x10/0x20
[ 119.145364] el0_sync_handler+0x134/0x140
[ 119.145381] el0_sync+0x180/0x1c0
Cc: jirislaby@kernel.org
Cc: stable@vger.kernel.org
Fixes: 47cab6a722 ("debug lockups: Improve lockup detection, fix generic arch fallback")
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Link: https://lore.kernel.org/r/20231009162021.3607632-1-usama.anjum@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 11e7f27b79 ]
There is a pid leakage:
------------------------------
unreferenced object 0xffff88810c181940 (size 224):
comm "sshd", pid 8191, jiffies 4294946950 (age 524.570s)
hex dump (first 32 bytes):
01 00 00 00 00 00 00 00 00 00 00 00 ad 4e ad de .............N..
ff ff ff ff 6b 6b 6b 6b ff ff ff ff ff ff ff ff ....kkkk........
backtrace:
[<ffffffff814774e6>] kmem_cache_alloc+0x5c6/0x9b0
[<ffffffff81177342>] alloc_pid+0x72/0x570
[<ffffffff81140ac4>] copy_process+0x1374/0x2470
[<ffffffff81141d77>] kernel_clone+0xb7/0x900
[<ffffffff81142645>] __se_sys_clone+0x85/0xb0
[<ffffffff8114269b>] __x64_sys_clone+0x2b/0x30
[<ffffffff83965a72>] do_syscall_64+0x32/0x80
[<ffffffff83a00085>] entry_SYSCALL_64_after_hwframe+0x61/0xc6
It turns out that there is a race condition between disassociate_ctty() and
tty_signal_session_leader(), which caused this leakage.
The pid memleak is triggered by the following race:
task[sshd] task[bash]
----------------------- -----------------------
disassociate_ctty();
spin_lock_irq(¤t->sighand->siglock);
put_pid(current->signal->tty_old_pgrp);
current->signal->tty_old_pgrp = NULL;
tty = tty_kref_get(current->signal->tty);
spin_unlock_irq(¤t->sighand->siglock);
tty_vhangup();
tty_lock(tty);
...
tty_signal_session_leader();
spin_lock_irq(&p->sighand->siglock);
...
if (tty->ctrl.pgrp) //tty->ctrl.pgrp is not NULL
p->signal->tty_old_pgrp = get_pid(tty->ctrl.pgrp); //An extra get
spin_unlock_irq(&p->sighand->siglock);
...
tty_unlock(tty);
if (tty) {
tty_lock(tty);
...
put_pid(tty->ctrl.pgrp);
tty->ctrl.pgrp = NULL; //It's too late
...
tty_unlock(tty);
}
The issue is believed to be introduced by commit c8bcd9c5be ("tty:
Fix ->session locking") who moves the unlock of siglock in
disassociate_ctty() above "if (tty)", making a small window allowing
tty_signal_session_leader() to kick in. It can be easily reproduced by
adding a delay before "if (tty)" and at the entrance of
tty_signal_session_leader().
To fix this issue, we move "put_pid(current->signal->tty_old_pgrp)" after
"tty->ctrl.pgrp = NULL".
Fixes: c8bcd9c5be ("tty: Fix ->session locking")
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Co-developed-by: GUO Zihua <guozihua@huawei.com>
Signed-off-by: GUO Zihua <guozihua@huawei.com>
Link: https://lore.kernel.org/r/20230831023329.165737-1-yiyang13@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e4876dacac upstream.
Some of the later revisions of the Brainboxes PX cards are based
on the Oxford Semiconductor chipset. Due to the chip's unique setup
these cards need to be initialised.
Previously these were tested against a reference card with the same broken
baudrate on another PC, cancelling out the effect. With this patch they
work and can transfer/receive find against an FTDI-based device.
Add all of the cards which require this setup to the quirks table.
Thanks to Maciej W. Rozycki for clarification on this chip.
Fixes: ef5a03a26c ("tty: 8250: Add support for Brainboxes PX cards.")
Cc: stable@vger.kernel.org
Signed-off-by: Cameron Williams <cang1@live.co.uk>
Link: https://lore.kernel.org/r/DU0PR02MB7899D222A4AB2A4E8C57108FC4DBA@DU0PR02MB7899.eurprd02.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a75b205de upstream.
gsm_cleanup_mux() cleans up the gsm by closing all DLCIs, stopping all
timers, removing the virtual tty devices and clearing the data queues.
This procedure, however, may cause subsequent changes of the virtual modem
status lines of a DLCI. More data is being added the outgoing data queue
and the deleted kick timer is restarted to handle this. At this point many
resources have already been removed by the cleanup procedure. Thus, a
kernel panic occurs.
Fix this by proving in gsm_modem_update() that the cleanup procedure has
not been started and the mux is still alive.
Note that writing to a virtual tty is already protected by checks against
the DLCI specific connection state.
Fixes: c568f7086c ("tty: n_gsm: fix missing timer to handle stalled links")
Cc: stable <stable@kernel.org>
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20231026055844.3127-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 560706eff7 ]
We now get errors on system suspend if no_console_suspend is set as
reported by Thomas. The errors started with commit 20a41a6261 ("serial:
8250_omap: Use force_suspend and resume for system suspend").
Let's fix the issue by checking for console_suspend_enabled in the system
suspend and resume path.
Note that with this fix the checks for console_suspend_enabled in
omap8250_runtime_suspend() become useless. We now keep runtime PM usage
count for an attached kernel console starting with commit bedb404e91
("serial: 8250_port: Don't use power management for kernel console").
Fixes: 20a41a6261 ("serial: 8250_omap: Use force_suspend and resume for system suspend")
Cc: stable <stable@kernel.org>
Cc: Udit Kumar <u-kumar1@ti.com>
Reported-by: Thomas Richard <thomas.richard@bootlin.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Thomas Richard <thomas.richard@bootlin.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230926061319.15140-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 398cecc248 ]
We must idle the uart only after serial8250_unregister_port(). Otherwise
unbinding the uart via sysfs while doing cat on the port produces an
imprecise external abort:
mem_serial_in from omap_8250_pm+0x44/0xf4
omap_8250_pm from uart_hangup+0xe0/0x194
uart_hangup from __tty_hangup.part.0+0x37c/0x3a8
__tty_hangup.part.0 from uart_remove_one_port+0x9c/0x22c
uart_remove_one_port from serial8250_unregister_port+0x60/0xe8
serial8250_unregister_port from omap8250_remove+0x6c/0xd0
omap8250_remove from platform_remove+0x28/0x54
Turns out the driver needs to have runtime PM functional before the
driver probe calls serial8250_register_8250_port(). And it needs
runtime PM after driver remove calls serial8250_unregister_port().
On probe, we need to read registers before registering the port in
omap_serial_fill_features_erratas(). We do that with custom uart_read()
already.
On remove, after serial8250_unregister_port(), we need to write to the
uart registers to idle the device. Let's add a custom uart_write() for
that.
Currently the uart register access depends on port->membase to be
initialized, which won't work after serial8250_unregister_port().
Let's use priv->membase instead, and use it for runtime PM related
functions to remove the dependency to port->membase for early and
late register access.
Note that during use, we need to check for a valid port in the runtime PM
related functions. This is needed for the optional wakeup configuration.
We now need to set the drvdata a bit earlier so it's available for the
runtime PM functions.
With the port checks in runtime PM functions, the old checks for priv in
omap8250_runtime_suspend() and omap8250_runtime_resume() functions are no
longer needed and are removed.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230508082014.23083-3-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 560706eff7 ("serial: 8250_omap: Fix errors with no_console_suspend")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cce7fc8b29 upstream.
In case the leaf driver wants to use IRQ polling (irq = 0) and
IIR register shows that an interrupt happened in the 8250 hardware
the IRQ data can be NULL. In such a case we need to skip the wake
event as we came to this path from the timer interrupt and quite
likely system is already awake.
Without this fix we have got an Oops:
serial8250: ttyS0 at I/O 0x3f8 (irq = 0, base_baud = 115200) is a 16550A
...
BUG: kernel NULL pointer dereference, address: 0000000000000010
RIP: 0010:serial8250_handle_irq+0x7c/0x240
Call Trace:
? serial8250_handle_irq+0x7c/0x240
? __pfx_serial8250_timeout+0x10/0x10
Fixes: 0ba9e3a13c ("serial: 8250: Add missing wakeup event reporting")
Cc: stable <stable@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230831222555.614426-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29346e217b upstream.
This reverts commit 9b9c8195f3.
The commit above is reverted as it did not solve the original issue.
gsm_cleanup_mux() tries to free up the virtual ttys by calling
gsm_dlci_release() for each available DLCI. There, dlci_put() is called to
decrease the reference counter for the DLCI via tty_port_put() which
finally calls gsm_dlci_free(). This already clears the pointer which is
being checked in gsm_cleanup_mux() before calling gsm_dlci_release().
Therefore, it is not necessary to clear this pointer in gsm_cleanup_mux()
as done in the reverted commit. The commit introduces a null pointer
dereference:
<TASK>
? __die+0x1f/0x70
? page_fault_oops+0x156/0x420
? search_exception_tables+0x37/0x50
? fixup_exception+0x21/0x310
? exc_page_fault+0x69/0x150
? asm_exc_page_fault+0x26/0x30
? tty_port_put+0x19/0xa0
gsmtty_cleanup+0x29/0x80 [n_gsm]
release_one_tty+0x37/0xe0
process_one_work+0x1e6/0x3e0
worker_thread+0x4c/0x3d0
? __pfx_worker_thread+0x10/0x10
kthread+0xe1/0x110
? __pfx_kthread+0x10/0x10
ret_from_fork+0x2f/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
The actual issue is that nothing guards dlci_put() from being called
multiple times while the tty driver was triggered but did not yet finished
calling gsm_dlci_free().
Fixes: 9b9c8195f3 ("tty: n_gsm: fix UAF in gsm_cleanup_mux")
Cc: stable <stable@kernel.org>
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20230914051507.3240-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f9608f1887 ]
The global pointer 'sprd_port' may not zero when sprd_probe returns
failure, that is a risk for sprd_port to be accessed afterward, and
may lead to unexpected errors.
For example:
There are two UART ports, UART1 is used for console and configured in
kernel command line, i.e. "console=";
The UART1 probe failed and the memory allocated to sprd_port[1] was
released, but sprd_port[1] was not set to NULL;
In UART2 probe, the same virtual address was allocated to sprd_port[2],
and UART2 probe process finally will go into sprd_console_setup() to
register UART1 as console since it is configured as preferred console
(filled to console_cmdline[]), but the console parameters (sprd_port[1])
belong to UART2.
So move the sprd_port[] assignment to where the port already initialized
can avoid the above issue.
Fixes: b7396a38fb ("tty/serial: Add Spreadtrum sc9836-uart driver support")
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20230725064053.235448-1-chunyan.zhang@unisoc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9baeea723c upstream.
When configuring a pin as an output pin with a value of logic 0, we
end up as having a value of logic 1 on the output pin. Setting a
logic 0 a second time (or more) after that will correctly output a
logic 0 on the output pin.
By default, all GPIO pins are configured as inputs. When we enter
sc16is7xx_gpio_direction_output() for the first time, we first set the
desired value in IOSTATE, and then we configure the pin as an output.
The datasheet states that writing to IOSTATE register will trigger a
transfer of the value to the I/O pin configured as output, so if the
pin is configured as an input, nothing will be transferred.
Therefore, set the direction first in IODIR, and then set the desired
value in IOSTATE.
This is what is done in NXP application note AN10587.
Fixes: dfeae619d7 ("serial: sc16is7xx")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Link: https://lore.kernel.org/r/20230807214556.540627-6-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2861ed4d6e upstream.
The sc16is7xx_config_rs485() function is called only for the second
port (index 1, channel B), causing initialization problems for the
first port.
For the sc16is7xx driver, port->membase and port->mapbase are not set,
and their default values are 0. And we set port->iobase to the device
index. This means that when the first device is registered using the
uart_add_one_port() function, the following values will be in the port
structure:
port->membase = 0
port->mapbase = 0
port->iobase = 0
Therefore, the function uart_configure_port() in serial_core.c will
exit early because of the following check:
/*
* If there isn't a port here, don't do anything further.
*/
if (!port->iobase && !port->mapbase && !port->membase)
return;
Typically, I2C and SPI drivers do not set port->membase and
port->mapbase.
The max310x driver sets port->membase to ~0 (all ones). By
implementing the same change in this driver, uart_configure_port() is
now correctly executed for all ports.
Fixes: dfeae619d7 ("serial: sc16is7xx")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Link: https://lore.kernel.org/r/20230807214556.540627-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dfe2aeb226 ]
Unloading a hardware specific 8250 driver can produce error "Unable to
handle kernel paging request at virtual address" about ten seconds after
unloading the driver. This happens on uart_hangup() calling
uart_change_pm().
Turns out commit 04e82793f0 ("serial: 8250: Reinit port->pm on port
specific driver unbind") was only a partial fix. If the hardware specific
driver has initialized port->pm function, we need to clear port->pm too.
Just reinitializing port->ops does not do this. Otherwise serial8250_pm()
will call port->pm() instead of serial8250_do_pm().
Fixes: 04e82793f0 ("serial: 8250: Reinit port->pm on port specific driver unbind")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230804131553.52927-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 282069845a upstream.
Do not read the data register to clear the error flags for lpuart32
platforms, the additional read may cause the receive FIFO underflow
since the DMA has already read the data register.
Actually all lpuart32 platforms support write 1 to clear those error
bits, let's use this method to better clear the error flags.
Fixes: 42b68768e5 ("serial: fsl_lpuart: DMA support for 32-bit variant")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230801022304.24251-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c4f8333b5 upstream.
In commit 9b9c8195f3 ("tty: n_gsm: fix UAF in gsm_cleanup_mux"), the UAF
problem is not completely fixed. There is a race condition in
gsm_cleanup_mux(), which caused this UAF.
The UAF problem is triggered by the following race:
task[5046] task[5054]
----------------------- -----------------------
gsm_cleanup_mux();
dlci = gsm->dlci[0];
mutex_lock(&gsm->mutex);
gsm_cleanup_mux();
dlci = gsm->dlci[0]; //Didn't take the lock
gsm_dlci_release(gsm->dlci[i]);
gsm->dlci[i] = NULL;
mutex_unlock(&gsm->mutex);
mutex_lock(&gsm->mutex);
dlci->dead = true; //UAF
Fix it by assigning values after mutex_lock().
Link: https://syzkaller.appspot.com/text?tag=CrashReport&x=176188b5a80000
Cc: stable <stable@kernel.org>
Fixes: 9b9c8195f3 ("tty: n_gsm: fix UAF in gsm_cleanup_mux")
Fixes: aa371e96f0 ("tty: n_gsm: fix restart handling via CLD command")
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Co-developed-by: Qiumiao Zhang <zhangqiumiao1@huawei.com>
Signed-off-by: Qiumiao Zhang <zhangqiumiao1@huawei.com>
Link: https://lore.kernel.org/r/20230811031121.153237-1-yiyang13@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christoph Niedermaier
Oliver Neukum
Jiri Slaby (SUSE)
Paul Geurts
Uwe Kleine-König
Hugo Villeneuve
Ronald Wahl
Daniel Mack
Arnd Bergmann
Pavel Krasavin
Lad Prabhakar
David Woodhouse
Muhammad Usama Anjum
Yi Yang
Cameron Williams
Daniel Starke
Geert Uytterhoeven
Tony Lindgren
Andy Shevchenko
Christophe Leroy
Chunyan Zhang
Johan Hovold
Sherry Sun
Robert Hodaszi