[ Upstream commit b34f4de6d3 ]
'qos_pfc' test checks PFC behavior. The idea is to limit the traffic
using a shaper somewhere in the flow of the packets. In this area, the
buffer is smaller than the buffer at the beginning of the flow, so it fills
up until there is no more space left. The test configures there PFC
which is supposed to notice that the headroom is filling up and send PFC
Xoff to indicate the transmitter to stop sending traffic for the priorities
sharing this PG.
The Xon/Xoff threshold is auto-configured and always equal to
2*(MTU rounded up to cell size). Even after sending the PFC Xoff packet,
traffic will keep arriving until the transmitter receives and processes
the PFC packet. This amount of traffic is known as the PFC delay allowance.
Currently the buffer for the delay traffic is configured as 100KB. The
MTU in the test is 10KB, therefore the threshold for Xoff is about 20KB.
This allows 80KB extra to be stored in this buffer.
8-lane ports use two buffers among which the configured buffer is split,
the Xoff threshold then applies to each buffer in parallel.
The test does not take into account the behavior of 8-lane ports, when the
ports are configured to 400Gbps with 8 lanes or 800Gbps with 8 lanes,
packets are dropped and the test fails.
Check if the relevant ports use 8 lanes, in such case double the size of
the buffer, as the headroom is split half-half.
Cc: Shuah Khan <shuah@kernel.org>
Fixes: bfa804784e ("selftests: mlxsw: Add a PFC test")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/23ff11b7dff031eb04a41c0f5254a2b636cd8ebb.1705502064.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 483ae90d8f ]
When tc filters are first added to a net device, the corresponding local
port gets bound to an ACL group in the device. The group contains a list
of ACLs. In turn, each ACL points to a different TCAM region where the
filters are stored. During forwarding, the ACLs are sequentially
evaluated until a match is found.
One reason to place filters in different regions is when they are added
with decreasing priorities and in an alternating order so that two
consecutive filters can never fit in the same region because of their
key usage.
In Spectrum-2 and newer ASICs the firmware started to report that the
maximum number of ACLs in a group is more than 16, but the layout of the
register that configures ACL groups (PAGT) was not updated to account
for that. It is therefore possible to hit stack corruption [1] in the
rare case where more than 16 ACLs in a group are required.
Fix by limiting the maximum ACL group size to the minimum between what
the firmware reports and the maximum ACLs that fit in the PAGT register.
Add a test case to make sure the machine does not crash when this
condition is hit.
[1]
Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: mlxsw_sp_acl_tcam_group_update+0x116/0x120
[...]
dump_stack_lvl+0x36/0x50
panic+0x305/0x330
__stack_chk_fail+0x15/0x20
mlxsw_sp_acl_tcam_group_update+0x116/0x120
mlxsw_sp_acl_tcam_group_region_attach+0x69/0x110
mlxsw_sp_acl_tcam_vchunk_get+0x492/0xa20
mlxsw_sp_acl_tcam_ventry_add+0x25/0xe0
mlxsw_sp_acl_rule_add+0x47/0x240
mlxsw_sp_flower_replace+0x1a9/0x1d0
tc_setup_cb_add+0xdc/0x1c0
fl_hw_replace_filter+0x146/0x1f0
fl_change+0xc17/0x1360
tc_new_tfilter+0x472/0xb90
rtnetlink_rcv_msg+0x313/0x3b0
netlink_rcv_skb+0x58/0x100
netlink_unicast+0x244/0x390
netlink_sendmsg+0x1e4/0x440
____sys_sendmsg+0x164/0x260
___sys_sendmsg+0x9a/0xe0
__sys_sendmsg+0x7a/0xc0
do_syscall_64+0x40/0xe0
entry_SYSCALL_64_after_hwframe+0x63/0x6b
Fixes: c3ab435466 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Reported-by: Orel Hagag <orelh@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/2d91c89afba59c22587b444994ae419dbea8d876.1705502064.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d6eeabcfa ]
Lately, a bug was found when many TC filters are added - at some point,
several bugs are printed to dmesg [1] and the switch is crashed with
segmentation fault.
The issue starts when gen_pool_free() fails because of unexpected
behavior - a try to free memory which is already freed, this leads to BUG()
call which crashes the switch and makes many other bugs.
Trying to track down the unexpected behavior led to a bug in eRP code. The
function mlxsw_sp_acl_erp_table_alloc() gets a pointer to the allocated
index, sets the value and returns an error code. When gen_pool_alloc()
fails it returns address 0, we track it and return -ENOBUFS outside, BUT
the call for gen_pool_alloc() already override the index in erp_table
structure. This is a problem when such allocation is done as part of
table expansion. This is not a new table, which will not be used in case
of allocation failure. We try to expand eRP table and override the
current index (non-zero) with zero. Then, it leads to an unexpected
behavior when address 0 is freed twice. Note that address 0 is valid in
erp_table->base_index and indeed other tables use it.
gen_pool_alloc() fails in case that there is no space left in the
pre-allocated pool, in our case, the pool is limited to
ACL_MAX_ERPT_BANK_SIZE, which is read from hardware. When more than max
erp entries are required, we exceed the limit and return an error, this
error leads to "Failed to migrate vregion" print.
Fix this by changing erp_table->base_index only in case of a successful
allocation.
Add a test case for such a scenario. Without this fix it causes
segmentation fault:
$ TESTS="max_erp_entries_test" ./tc_flower.sh
./tc_flower.sh: line 988: 1560 Segmentation fault tc filter del dev $h2 ingress chain $i protocol ip pref $i handle $j flower &>/dev/null
[1]:
kernel BUG at lib/genalloc.c:508!
invalid opcode: 0000 [#1] PREEMPT SMP
CPU: 6 PID: 3531 Comm: tc Not tainted 6.7.0-rc5-custom-ga6893f479f5e #1
Hardware name: Mellanox Technologies Ltd. MSN4700/VMOD0010, BIOS 5.11 07/12/2021
RIP: 0010:gen_pool_free_owner+0xc9/0xe0
...
Call Trace:
<TASK>
__mlxsw_sp_acl_erp_table_other_dec+0x70/0xa0 [mlxsw_spectrum]
mlxsw_sp_acl_erp_mask_destroy+0xf5/0x110 [mlxsw_spectrum]
objagg_obj_root_destroy+0x18/0x80 [objagg]
objagg_obj_destroy+0x12c/0x130 [objagg]
mlxsw_sp_acl_erp_mask_put+0x37/0x50 [mlxsw_spectrum]
mlxsw_sp_acl_ctcam_region_entry_remove+0x74/0xa0 [mlxsw_spectrum]
mlxsw_sp_acl_ctcam_entry_del+0x1e/0x40 [mlxsw_spectrum]
mlxsw_sp_acl_tcam_ventry_del+0x78/0xd0 [mlxsw_spectrum]
mlxsw_sp_flower_destroy+0x4d/0x70 [mlxsw_spectrum]
mlxsw_sp_flow_block_cb+0x73/0xb0 [mlxsw_spectrum]
tc_setup_cb_destroy+0xc1/0x180
fl_hw_destroy_filter+0x94/0xc0 [cls_flower]
__fl_delete+0x1ac/0x1c0 [cls_flower]
fl_destroy+0xc2/0x150 [cls_flower]
tcf_proto_destroy+0x1a/0xa0
...
mlxsw_spectrum3 0000:07:00.0: Failed to migrate vregion
mlxsw_spectrum3 0000:07:00.0: Failed to migrate vregion
Fixes: f465261aa1 ("mlxsw: spectrum_acl: Implement common eRP core")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/4cfca254dfc0e5d283974801a24371c7b6db5989.1705502064.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f922c7b1c1 ]
When devlink instance is put into network namespace and that network
namespace gets deleted, devlink instance is moved back into init_ns.
This is done as a part of cleanup_net() routine. Since cleanup_net()
is called asynchronously from workqueue, there is no guarantee that
the devlink instance move is done after "ip netns del" returns.
So fix this race by making sure that the devlink instance is present
before any other operation.
Reported-by: Amir Tzin <amirtz@nvidia.com>
Fixes: b74c37fd35 ("selftests: netdevsim: add tests for devlink reload with resources")
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20230220132336.198597-1-jiri@resnulli.us
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2fc60e2ff9 ]
$number + > bash means redirect FD $number, e.g. commonly
used 2> redirects stderr (fd 2). The test uses 8192> to
write the number 8192 to a file, this results in:
./devlink.sh: line 499: 8192: Bad file descriptor
Oddly the test also papers over this issue by checking
for failure (expecting an error rather than success)
so it passes, anyway.
Fixes: ff18176ad8 ("selftests: Add a test of large binary to devlink health test")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 044011fdf1 ]
The test verifies that packets are correctly flooded by the bridge and
the VXLAN device by matching on the encapsulated packets at the other
end. However, if packets other than those generated by the test also
ingress the bridge (e.g., MLD packets), they will be flooded as well and
interfere with the expected count.
Make the test more robust by making sure that only the packets generated
by the test can ingress the bridge. Drop all the rest using tc filters
on the egress of 'br0' and 'h1'.
In the software data path, the problem can be solved by matching on the
inner destination MAC or dropping unwanted packets at the egress of the
VXLAN device, but this is not currently supported by mlxsw.
Fixes: 94d302deae ("selftests: mlxsw: Add a test for VxLAN flooding")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 196f9bc050 ]
The test runs several test cases and is supposed to return an error in
case at least one of them failed.
Currently, the check of the return value of each test case is in the
wrong place, which can result in the wrong return value. For example:
# TESTS='tc_police' ./resource_scale.sh
TEST: 'tc_police' [default] 968 [FAIL]
tc police offload count failed
Error: mlxsw_spectrum: Failed to allocate policer index.
We have an error talking to the kernel
Command failed /tmp/tmp.i7Oc5HwmXY:969
TEST: 'tc_police' [default] overflow 969 [ OK ]
...
TEST: 'tc_police' [ipv4_max] overflow 969 [ OK ]
$ echo $?
0
Fix this by moving the check to be done after each test case.
Fixes: 059b18e21c ("selftests: mlxsw: Return correct error code in resource scale test")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit dc97520753 upstream.
The test adds tc filters and checks how many of them were offloaded by
grepping for 'in_hw'.
iproute2 commit f4cd4f127047 ("tc: add skip_hw and skip_sw to control
action offload") added offload indication to tc actions, producing the
following output:
$ tc filter show dev swp2 ingress
...
filter protocol ipv6 pref 1000 flower chain 0 handle 0x7c0
eth_type ipv6
dst_ip 2001:db8:1::7bf
skip_sw
in_hw in_hw_count 1
action order 1: police 0x7c0 rate 10Mbit burst 100Kb mtu 2Kb action drop overhead 0b
ref 1 bind 1
not_in_hw
used_hw_stats immediate
The current grep expression matches on both 'in_hw' and 'not_in_hw',
resulting in incorrect results.
Fix that by using JSON output instead.
Fixes: 5061e77326 ("selftests: mlxsw: Add scale test for tc-police")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull Kselftest fixes from Shuah Khan:
"A fix to implicit declaration warns in drivers/dma-buf test"
* tag 'linux-kselftest-fixes-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: drivers/dma-buf: Fix implicit declaration warns
udmabuf has the following implicit declaration warns:
udmabuf.c:30:10: warning: implicit declaration of function 'open';
udmabuf.c:42:8: warning: implicit declaration of function 'fcntl'
These are caused due to not including fcntl.h and including just
linux/fcntl.h. Fix it to include fcntl.h which will bring in the
linux/fcntl.h. In addition, define __EXPORTED_HEADERS__ to bring in
F_ADD_SEALS and F_SEAL_SHRINK defines and fix the following error
that show up when just fcntl.h is included.
udmabuf.c:45:21: error: 'F_ADD_SEALS' undeclared
45 | ret = fcntl(memfd, F_ADD_SEALS, F_SEAL_SHRINK);
| ^~~~~~~~~~~
udmabuf.c:45:34: error: 'F_SEAL_SHRINK' undeclared
45 | ret = fcntl(memfd, F_ADD_SEALS, F_SEAL_SHRINK);
| ^~~~~~~~~~~~~
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
NXP Legal insists that the following are not fine:
- Saying "NXP Semiconductors" instead of "NXP", since the company's
registered name is "NXP"
- Putting a "(c)" sign in the copyright string
- Putting a comma in the copyright string
The only accepted copyright string format is "Copyright <year-range> NXP".
This patch changes the copyright headers in the networking files that
were sent by me, or derived from code sent by me.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hard drop counter check testcase, to make sure netdevsim driver
properly handles the devlink hard drop counters get/set callbacks.
Signed-off-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the commit referenced below, a check was added to devlink_lib that
asserts the existence of a devlink device referenced by $DEVLINK_DEV.
Unfortunately, several netdevsim tests point DEVLINK_DEV at a device that
does not exist at the time that devlink_lib is sourced. Thus these tests
spuriously fail.
Fix this by introducing an override. By setting DEVLINK_DEV to an empty
string, the user declares their intention to handle DEVLINK_DEV management
on their own.
In all netdevsim tests that use devlink_lib and set DEVLINK_DEV, set
instead an empty DEVLINK_DEV just before sourcing devlink_lib, and set it
to the correct value right afterwards.
Fixes: 557c4d2f78 ("selftests: devlink_lib: add check for devlink device existence")
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several tests do not set some ports down as part of their cleanup(),
resulting in IPv6 link-local addresses and associated routes not being
deleted.
These leaks were found using a BPF tool that monitors ASIC resources.
Solve this by setting the ports down at the end of the tests.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To check how many routes are installed in hardware, the test runs "ip
route" and greps for "offload", which includes routes with state
"offload_failed".
Till now, this wrong check was not found because after one failure in
route insertion, the driver moved to "abort" mode, which means that user
cannot try to add more routes.
The previous patch removed the abort mechanism and now failed routes are
counted as offloaded.
Fix this by not considering routes with "offload_failed" flag as
offloaded.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test verifies that netdevsim correctly implements devlink ops callbacks
that set node as a parent of devlink leaf or node rate object.
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test verifies that it is possible to create, delete and set min/max tx
rate of devlink rate node on netdevsim VF.
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the two users of this helper have been converted to iproute2 dcb,
it is not necessary anymore. Drop it.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a dedicated tool for configuration of DCB in iproute2 now. Use it
in the selftest instead of mlnx_qos.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a dedicated tool for configuration of DCB in iproute2 now. Use it
in the selftest instead of mlnx_qos.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test sometimes fails with an error message such as:
TEST: tc sample (w/ flower) rate (egress) [FAIL]
Expected 100 packets, got 70 packets, which is -30% off. Required accuracy is +-25%
Make the test more robust by generating more packets, therefore
increasing the number of expected samples. Decrease the transmission
delay in order not to needlessly prolong the test.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the array of the ports that were split in the port_scale test
is local, so the port_cleanup() unsplits an empty array.
Make the array global so the cleanup will be preformed properly.
Suggested-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mirror_gre_scale test creates as many ERSPAN sessions as the underlying
chip supports, and tests that they all work. In order to determine that it
issues a stream of ICMP packets and checks if they are mirrored as
expected.
However, the mausezahn invocation missed the -6 flag to identify the use of
IPv6 protocol, and was sending ICMP messages over IPv6, as opposed to
ICMP6. It also didn't pass an explicit source IP address, which apparently
worked at some point in the past, but does not anymore.
To fix these issues, extend the function mirror_test() in mirror_lib by
detecting the IPv6 protocol addresses, and using a different ICMP scheme.
Fix __mirror_gre_test() in the selftest itself to pass a source IP address.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The intention behind this test is to make sure that qdisc limit is
correctly projected to the HW. However, first, due to rounding in the
qdisc, and then in the driver, the number cannot actually be accurate. And
second, the approach to testing this is to oversubscribe the port with
traffic generated on the same switch. The actual backlog size therefore
fluctuates.
In practice, this test proved to be noisier than the rest, and spuriously
fails every now and then. Increase the tolerance to 10 % to avoid these
issues.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the resource scale test checks a few cases, when the error code
resets between the cases. So for example, if one case fails and the
consecutive case passes, the error code eventually will fit the last test
and will be 0.
Save a new return code that will hold the 'or' return codes of all the
cases, so the final return code will consider all the cases.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the error return code of the failure condition is lost after
using an if statement, so the test doesn't fail when it should.
Remove the if statement that separates the condition and the error code
check, so the test won't always pass.
Fixes: abfce9e062 ("selftests: mlxsw: Reduce running time using offload indication")
Reported-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the error return code of the failure condition is lost after
using an if statement, so the test doesn't fail when it should.
Remove the if statement that separates the condition and the error code
check, so the test won't always pass.
Fixes: 5154b1b826 ("selftests: mlxsw: Add a scale test for physical ports")
Reported-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was a bug introduced during the rework which cause non-zero backlog
being stuck at ETS. Introduce a selftest that would have caught the issue
earlier.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that two sampling rules cannot be configured on the same port with
the same trigger.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver can only offload matchall rules that do not match on a
protocol. Test that matchall rules that match on a protocol are vetoed.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that unsupported resilient nexthop group configurations are
rejected and that offload / trap indication is correctly set on nexthop
buckets in a resilient group.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of nexthop buckets in a resilient nexthop group never
changes, so when the gateway address of a nexthop cannot be resolved,
the nexthop buckets are programmed to trap packets to the CPU in order
to trigger resolution. For example:
# ip nexthop add id 1 via 198.51.100.1 dev swp3
# ip nexthop add id 10 group 1 type resilient buckets 32
# ip nexthop bucket get id 10 index 0
id 10 index 0 idle_time 1.44 nhid 1 trap
Where 198.51.100.1 is a made-up IP.
Test that in this case packets are indeed trapped to the CPU via the
unresolved neigh trap.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
q_in_vni_veto.sh is not needed anymore because VxLAN with an 802.1ad
bridge and VxLAN with an 802.1d bridge can coexist.
Remove the test.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure egress sampling configuration only fails on Spectrum-1, given
that mlxsw now supports it on Spectrum-{2,3}.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that packets are sampled when tc-sample is used with matchall
egress binding and flower classifier. Verify that when performing
sampling on egress the end-to-end latency is reported as metadata.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that packets are sampled when tc-sample is used and that reported
metadata is correct. Two sets of hosts (with and without LAG) are used,
since metadata extraction in mlxsw is a bit different when LAG is
involved.
# ./tc_sample.sh
TEST: tc sample rate (forward) [ OK ]
TEST: tc sample rate (local receive) [ OK ]
TEST: tc sample maximum rate [ OK ]
TEST: tc sample group conflict test [ OK ]
TEST: tc sample iif [ OK ]
TEST: tc sample lag iif [ OK ]
TEST: tc sample oif [ OK ]
TEST: tc sample lag oif [ OK ]
TEST: tc sample out-tc [ OK ]
TEST: tc sample out-tc-occ [ OK ]
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test various aspects of psample functionality over netdevsim and in
particular test that the psample module correctly reports the provided
metadata.
Example:
# ./psample.sh
TEST: psample enable / disable [ OK ]
TEST: psample group number [ OK ]
TEST: psample metadata [ OK ]
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test various aspects of the resilient nexthop group offload API on top
of the netdevsim implementation. Both good and bad flows are tested.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Co-developed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cases to verify that when debugfs variable "fail_route_offload" is
set, notification with "rt_offload_failed" flag is received.
Extend the existing cases to verify that when sysctl
"fib_notify_on_flag_change" is set to 2, the kernel emits notifications
only for failed route installation.
$ ./fib_notifications.sh
TEST: IPv4 route addition [ OK ]
TEST: IPv4 route deletion [ OK ]
TEST: IPv4 route replacement [ OK ]
TEST: IPv4 route offload failed [ OK ]
TEST: IPv6 route addition [ OK ]
TEST: IPv6 route deletion [ OK ]
TEST: IPv6 route replacement [ OK ]
TEST: IPv6 route offload failed [ OK ]
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that setting lanes parameter is working.
Set max speed and max lanes in the list of advertised link modes,
and then try to set max speed with the lanes below max lanes if exists
in the list.
And then, test that setting number of lanes larger than max lanes fails.
Do the above for both autoneg on and off.
$ ./ethtool_lanes.sh
TEST: 4 lanes is autonegotiated [ OK ]
TEST: Lanes number larger than max width is not set [ OK ]
TEST: Autoneg off, 4 lanes detected during force mode [ OK ]
TEST: Lanes number larger than max width is not set [ OK ]
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add test to check fib notifications behavior.
The test checks route addition, route deletion and route replacement for
both IPv4 and IPv6.
When fib_notify_on_flag_change=0, expect single notification for route
addition/deletion/replacement.
When fib_notify_on_flag_change=1, expect:
- two notification for route addition/replacement, first without RTM_F_TRAP
and second with RTM_F_TRAP.
- single notification for route deletion.
$ ./fib_notifications.sh
TEST: IPv4 route addition [ OK ]
TEST: IPv4 route deletion [ OK ]
TEST: IPv4 route replacement [ OK ]
TEST: IPv6 route addition [ OK ]
TEST: IPv6 route deletion [ OK ]
TEST: IPv6 route replacement [ OK ]
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Run the test cases with both `fib_notify_on_flag_change` sysctls set to
'1', and then with both sysctls set to '0' to verify there are no
regressions in the test when notifications are added.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Query the maximum number of supported physical ports using devlink-resource
and test that this number can be reached by splitting each of the
splittable ports to its width. Test that an error is returned in case
the maximum number is exceeded.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking fixes from Jakub Kicinski:
"Networking fixes, including fixes from netfilter, wireless and bpf
trees.
Current release - regressions:
- mt76: fix NULL pointer dereference in mt76u_status_worker and
mt76s_process_tx_queue
- net: ipa: fix interconnect enable bug
Current release - always broken:
- netfilter: fixes possible oops in mtype_resize in ipset
- ath11k: fix number of coding issues found by static analysis tools
and spurious error messages
Previous releases - regressions:
- e1000e: re-enable s0ix power saving flows for systems with the
Intel i219-LM Ethernet controllers to fix power use regression
- virtio_net: fix recursive call to cpus_read_lock() to avoid a
deadlock
- ipv4: ignore ECN bits for fib lookups in fib_compute_spec_dst()
- sysfs: take the rtnl lock around XPS configuration
- xsk: fix memory leak for failed bind and rollback reservation at
NETDEV_TX_BUSY
- r8169: work around power-saving bug on some chip versions
Previous releases - always broken:
- dcb: validate netlink message in DCB handler
- tun: fix return value when the number of iovs exceeds MAX_SKB_FRAGS
to prevent unnecessary retries
- vhost_net: fix ubuf refcount when sendmsg fails
- bpf: save correct stopping point in file seq iteration
- ncsi: use real net-device for response handler
- neighbor: fix div by zero caused by a data race (TOCTOU)
- bareudp: fix use of incorrect min_headroom size and a false
positive lockdep splat from the TX lock
- mvpp2:
- clear force link UP during port init procedure in case
bootloader had set it
- add TCAM entry to drop flow control pause frames
- fix PPPoE with ipv6 packet parsing
- fix GoP Networking Complex Control config of port 3
- fix pkt coalescing IRQ-threshold configuration
- xsk: fix race in SKB mode transmit with shared cq
- ionic: account for vlan tag len in rx buffer len
- stmmac: ignore the second clock input, current clock framework does
not handle exclusive clock use well, other drivers may reconfigure
the second clock
Misc:
- ppp: change PPPIOCUNBRIDGECHAN ioctl request number to follow
existing scheme"
* tag 'net-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (99 commits)
net: dsa: lantiq_gswip: Fix GSWIP_MII_CFG(p) register access
net: dsa: lantiq_gswip: Enable GSWIP_MII_CFG_EN also for internal PHYs
net: lapb: Decrease the refcount of "struct lapb_cb" in lapb_device_event
r8169: work around power-saving bug on some chip versions
net: usb: qmi_wwan: add Quectel EM160R-GL
selftests: mlxsw: Set headroom size of correct port
net: macb: Correct usage of MACB_CAPS_CLK_HW_CHG flag
ibmvnic: fix: NULL pointer dereference.
docs: networking: packet_mmap: fix old config reference
docs: networking: packet_mmap: fix formatting for C macros
vhost_net: fix ubuf refcount incorrectly when sendmsg fails
bareudp: Fix use of incorrect min_headroom size
bareudp: set NETIF_F_LLTX flag
net: hdlc_ppp: Fix issues when mod_timer is called while timer is running
atlantic: remove architecture depends
erspan: fix version 1 check in gre_parse_header()
net: hns: fix return value check in __lb_other_process()
net: sched: prevent invalid Scell_log shift count
net: neighbor: fix a crash caused by mod zero
ipv4: Ignore ECN bits for fib lookups in fib_compute_spec_dst()
...
The test was setting the headroom size of the wrong port. This was not
visible because of a firmware bug that canceled this bug.
Set the headroom size of the correct port, so that the test will pass
with both old and new firmware versions.
Fixes: bfa804784e ("selftests: mlxsw: Add a PFC test")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/20201230114251.394009-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski
Amit Cohen
Ido Schimmel
Jiri Pirko
Vladimir Oltean
Linus Torvalds
Shuah Khan
Oleksandr Mazur
Petr Machata
Dmytro Linkin
Ido Schimmel
Danielle Ratson