[ Upstream commit 7d9896e9f6 ]
Since commit 6e890c5d50 ("vhost: use vhost_tasks for worker threads"),
the vhost uses vhost_task and operates as a child of the
owner thread. This is required for correct CPU usage accounting,
especially when using containers.
However, this change has caused confusion for some legacy
userspace applications, and we didn't notice until it's too late.
Unfortunately, it's too late to revert - we now have userspace
depending both on old and new behaviour :(
To address the issue, reintroduce kthread mode for vhost workers and
provide a configuration to select between kthread and task worker.
- Add 'fork_owner' parameter to vhost_dev to let users select kthread
or task mode. Default mode is task mode(VHOST_FORK_OWNER_TASK).
- Reintroduce kthread mode support:
* Bring back the original vhost_worker() implementation,
and renamed to vhost_run_work_kthread_list().
* Add cgroup support for the kthread
* Introduce struct vhost_worker_ops:
- Encapsulates create / stop / wake‑up callbacks.
- vhost_worker_create() selects the proper ops according to
inherit_owner.
- Userspace configuration interface:
* New IOCTLs:
- VHOST_SET_FORK_FROM_OWNER lets userspace select task mode
(VHOST_FORK_OWNER_TASK) or kthread mode (VHOST_FORK_OWNER_KTHREAD)
- VHOST_GET_FORK_FROM_OWNER reads the current worker mode
* Expose module parameter 'fork_from_owner_default' to allow system
administrators to configure the default mode for vhost workers
* Kconfig option CONFIG_VHOST_ENABLE_FORK_OWNER_CONTROL controls whether
these IOCTLs and the parameter are available
- The VHOST_NEW_WORKER functionality requires fork_owner to be set
to true, with validation added to ensure proper configuration
This partially reverts or improves upon:
commit 6e890c5d50 ("vhost: use vhost_tasks for worker threads")
commit 1cdaafa1b8 ("vhost: replace single worker pointer with xarray")
Fixes: 6e890c5d50 ("vhost: use vhost_tasks for worker threads"),
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20250714071333.59794-2-lulu@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69cd720a8a ]
As part of the normal initiator side scanning the guest's scsi layer
will loop over all possible targets and send an inquiry. Since the
max number of targets for virtio-scsi is 256, this can result in 255
error messages about targets not existing if you only have a single
target. When there's more than 1 vhost-scsi device each with a single
target, then you get N * 255 log messages.
It looks like the log message was added by accident in:
commit 3f8ca2e115 ("vhost/scsi: Extract common handling code from
control queue handler")
when we added common helpers. Then in:
commit 09d7583294 ("vhost/scsi: Use common handling code in request
queue handler")
we converted the scsi command processing path to use the new
helpers so we started to see the extra log messages during scanning.
The patches were just making some code common but added the vq_err
call and I'm guessing the patch author forgot to enable the vq_err
call (vq_err is implemented by pr_debug which defaults to off). So
this patch removes the call since it's expected to hit this path
during device discovery.
Fixes: 09d7583294 ("vhost/scsi: Use common handling code in request queue handler")
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20250611210113.10912-1-michael.christie@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f591cf9fce ]
The vhost-scsi completion path may access vq->log_base when vq->log_used is
already set to false.
vhost-thread QEMU-thread
vhost_scsi_complete_cmd_work()
-> vhost_add_used()
-> vhost_add_used_n()
if (unlikely(vq->log_used))
QEMU disables vq->log_used
via VHOST_SET_VRING_ADDR.
mutex_lock(&vq->mutex);
vq->log_used = false now!
mutex_unlock(&vq->mutex);
QEMU gfree(vq->log_base)
log_used()
-> log_write(vq->log_base)
Assuming the VMM is QEMU. The vq->log_base is from QEMU userpace and can be
reclaimed via gfree(). As a result, this causes invalid memory writes to
QEMU userspace.
The control queue path has the same issue.
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Message-Id: <20250403063028.16045-2-dongli.zhang@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58465d8607 ]
Although the support of VIRTIO_F_ANY_LAYOUT + VIRTIO_F_VERSION_1 was
signaled by the commit 664ed90e62 ("vhost/scsi: Set
VIRTIO_F_ANY_LAYOUT + VIRTIO_F_VERSION_1 feature bits"),
vhost_scsi_send_bad_target() still assumes the response in a single
descriptor.
Similar issue in vhost_scsi_send_bad_target() has been fixed in previous
commit. In addition, similar issue for vhost_scsi_complete_cmd_work() has
been fixed by the commit 6dd88fd59d ("vhost-scsi: unbreak any layout for
response").
Fixes: 3ca51662f8 ("vhost-scsi: Add better resource allocation failure handling")
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Message-Id: <20250403063028.16045-4-dongli.zhang@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b182687135 ]
Although the support of VIRTIO_F_ANY_LAYOUT + VIRTIO_F_VERSION_1 was
signaled by the commit 664ed90e62 ("vhost/scsi: Set
VIRTIO_F_ANY_LAYOUT + VIRTIO_F_VERSION_1 feature bits"),
vhost_scsi_send_bad_target() still assumes the response in a single
descriptor.
In addition, although vhost_scsi_send_bad_target() is used by both I/O
queue and control queue, the response header is always
virtio_scsi_cmd_resp. It is required to use virtio_scsi_ctrl_tmf_resp or
virtio_scsi_ctrl_an_resp for control queue.
Fixes: 664ed90e62 ("vhost/scsi: Set VIRTIO_F_ANY_LAYOUT + VIRTIO_F_VERSION_1 feature bits")
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Message-Id: <20250403063028.16045-3-dongli.zhang@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ca51662f8 ]
If we can't allocate mem to map in data for a request or can't find
a tag for a command, we currently drop the command. This leads to the
error handler running to clean it up. Instead of dropping the command
this has us return an error telling the initiator that it queued more
commands than we can handle. The initiator will then reduce how many
commands it will send us and retry later.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Message-Id: <20241203191705.19431-4-michael.christie@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Stable-dep-of: b182687135 ("vhost-scsi: Fix vhost_scsi_send_bad_target()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5dd639a164 ]
If vhost_scsi_set_endpoint is called multiple times without a
vhost_scsi_clear_endpoint between them, we can hit multiple bugs
found by Haoran Zhang:
1. Use-after-free when no tpgs are found:
This fixes a use after free that occurs when vhost_scsi_set_endpoint is
called more than once and calls after the first call do not find any
tpgs to add to the vs_tpg. When vhost_scsi_set_endpoint first finds
tpgs to add to the vs_tpg array match=true, so we will do:
vhost_vq_set_backend(vq, vs_tpg);
...
kfree(vs->vs_tpg);
vs->vs_tpg = vs_tpg;
If vhost_scsi_set_endpoint is called again and no tpgs are found
match=false so we skip the vhost_vq_set_backend call leaving the
pointer to the vs_tpg we then free via:
kfree(vs->vs_tpg);
vs->vs_tpg = vs_tpg;
If a scsi request is then sent we do:
vhost_scsi_handle_vq -> vhost_scsi_get_req -> vhost_vq_get_backend
which sees the vs_tpg we just did a kfree on.
2. Tpg dir removal hang:
This patch fixes an issue where we cannot remove a LIO/target layer
tpg (and structs above it like the target) dir due to the refcount
dropping to -1.
The problem is that if vhost_scsi_set_endpoint detects a tpg is already
in the vs->vs_tpg array or if the tpg has been removed so
target_depend_item fails, the undepend goto handler will do
target_undepend_item on all tpgs in the vs_tpg array dropping their
refcount to 0. At this time vs_tpg contains both the tpgs we have added
in the current vhost_scsi_set_endpoint call as well as tpgs we added in
previous calls which are also in vs->vs_tpg.
Later, when vhost_scsi_clear_endpoint runs it will do
target_undepend_item on all the tpgs in the vs->vs_tpg which will drop
their refcount to -1. Userspace will then not be able to remove the tpg
and will hang when it tries to do rmdir on the tpg dir.
3. Tpg leak:
This fixes a bug where we can leak tpgs and cause them to be
un-removable because the target name is overwritten when
vhost_scsi_set_endpoint is called multiple times but with different
target names.
The bug occurs if a user has called VHOST_SCSI_SET_ENDPOINT and setup
a vhost-scsi device to target/tpg mapping, then calls
VHOST_SCSI_SET_ENDPOINT again with a new target name that has tpgs we
haven't seen before (target1 has tpg1 but target2 has tpg2). When this
happens we don't teardown the old target tpg mapping and just overwrite
the target name and the vs->vs_tpg array. Later when we do
vhost_scsi_clear_endpoint, we are passed in either target1 or target2's
name and we will only match that target's tpgs when we loop over the
vs->vs_tpg. We will then return from the function without doing
target_undepend_item on the tpgs.
Because of all these bugs, it looks like being able to call
vhost_scsi_set_endpoint multiple times was never supported. The major
user, QEMU, already has checks to prevent this use case. So to fix the
issues, this patch prevents vhost_scsi_set_endpoint from being called
if it's already successfully added tpgs. To add, remove or change the
tpg config or target name, you must do a vhost_scsi_clear_endpoint
first.
Fixes: 25b98b64e2 ("vhost scsi: alloc cmds per vq instead of session")
Fixes: 4f7f46d32c ("tcm_vhost: Use vq->private_data to indicate if the endpoint is setup")
Reported-by: Haoran Zhang <wh1sper@zju.edu.cn>
Closes: https://lore.kernel.org/virtualization/e418a5ee-45ca-4d18-9b5d-6f8b6b1add8e@oracle.com/T/#me6c0041ce376677419b9b2563494172a01487ecb
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20250129210922.121533-1-michael.christie@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Pull virtio fixes from Michael Tsirkin:
"Several small bugfixes all over the place.
Most notably, fixes the vsock allocation with GFP_KERNEL in atomic
context, which has been triggering warnings for lots of testers"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost/scsi: null-ptr-dereference in vhost_scsi_get_req()
vsock/virtio: use GFP_ATOMIC under RCU read lock
virtio_console: fix misc probe bugs
virtio_ring: tag event_triggered as racy for KCSAN
vdpa/octeon_ep: Fix format specifier for pointers in debug messages
Since commit 3f8ca2e115 ("vhost/scsi: Extract common handling code
from control queue handler") a null pointer dereference bug can be
triggered when guest sends an SCSI AN request.
In vhost_scsi_ctl_handle_vq(), `vc.target` is assigned with
`&v_req.tmf.lun[1]` within a switch-case block and is then passed to
vhost_scsi_get_req() which extracts `vc->req` and `tpg`. However, for
a `VIRTIO_SCSI_T_AN_*` request, tpg is not required, so `vc.target` is
set to NULL in this branch. Later, in vhost_scsi_get_req(),
`vc->target` is dereferenced without being checked, leading to a null
pointer dereference bug. This bug can be triggered from guest.
When this bug occurs, the vhost_worker process is killed while holding
`vq->mutex` and the corresponding tpg will remain occupied
indefinitely.
Below is the KASAN report:
Oops: general protection fault, probably for non-canonical address
0xdffffc0000000000: 0000 [#1] PREEMPT SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 1 PID: 840 Comm: poc Not tainted 6.10.0+ #1
Hardware name: QEMU Ubuntu 24.04 PC (i440FX + PIIX, 1996), BIOS
1.16.3-debian-1.16.3-2 04/01/2014
RIP: 0010:vhost_scsi_get_req+0x165/0x3a0
Code: 00 fc ff df 48 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 2b 02 00 00
48 b8 00 00 00 00 00 fc ff df 4d 8b 65 30 4c 89 e2 48 c1 ea 03 <0f> b6
04 02 4c 89 e2 83 e2 07 38 d0 7f 08 84 c0 0f 85 be 01 00 00
RSP: 0018:ffff888017affb50 EFLAGS: 00010246
RAX: dffffc0000000000 RBX: ffff88801b000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff888017affcb8
RBP: ffff888017affb80 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
R13: ffff888017affc88 R14: ffff888017affd1c R15: ffff888017993000
FS: 000055556e076500(0000) GS:ffff88806b100000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000200027c0 CR3: 0000000010ed0004 CR4: 0000000000370ef0
Call Trace:
<TASK>
? show_regs+0x86/0xa0
? die_addr+0x4b/0xd0
? exc_general_protection+0x163/0x260
? asm_exc_general_protection+0x27/0x30
? vhost_scsi_get_req+0x165/0x3a0
vhost_scsi_ctl_handle_vq+0x2a4/0xca0
? __pfx_vhost_scsi_ctl_handle_vq+0x10/0x10
? __switch_to+0x721/0xeb0
? __schedule+0xda5/0x5710
? __kasan_check_write+0x14/0x30
? _raw_spin_lock+0x82/0xf0
vhost_scsi_ctl_handle_kick+0x52/0x90
vhost_run_work_list+0x134/0x1b0
vhost_task_fn+0x121/0x350
...
</TASK>
---[ end trace 0000000000000000 ]---
Let's add a check in vhost_scsi_get_req.
Fixes: 3f8ca2e115 ("vhost/scsi: Extract common handling code from control queue handler")
Signed-off-by: Haoran Zhang <wh1sper@zju.edu.cn>
[whitespace fixes]
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Message-Id: <b26d7ddd-b098-4361-88f8-17ca7f90adf7@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
Pull virtio updates from Michael Tsirkin:
"Several new features here:
- virtio-balloon supports new stats
- vdpa supports setting mac address
- vdpa/mlx5 suspend/resume as well as MKEY ops are now faster
- virtio_fs supports new sysfs entries for queue info
- virtio/vsock performance has been improved
And fixes, cleanups all over the place"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (34 commits)
vsock/virtio: avoid queuing packets when intermediate queue is empty
vsock/virtio: refactor virtio_transport_send_pkt_work
fw_cfg: Constify struct kobj_type
vdpa/mlx5: Postpone MR deletion
vdpa/mlx5: Introduce init/destroy for MR resources
vdpa/mlx5: Rename mr_mtx -> lock
vdpa/mlx5: Extract mr members in own resource struct
vdpa/mlx5: Rename function
vdpa/mlx5: Delete direct MKEYs in parallel
vdpa/mlx5: Create direct MKEYs in parallel
MAINTAINERS: add virtio-vsock driver in the VIRTIO CORE section
virtio_fs: add sysfs entries for queue information
virtio_fs: introduce virtio_fs_put_locked helper
vdpa: Remove unused declarations
vdpa/mlx5: Parallelize VQ suspend/resume for CVQ MQ command
vdpa/mlx5: Small improvement for change_num_qps()
vdpa/mlx5: Keep notifiers during suspend but ignore
vdpa/mlx5: Parallelize device resume
vdpa/mlx5: Parallelize device suspend
vdpa/mlx5: Use async API for vq modify commands
...
We used to call irq_bypass_unregister_producer() in
vhost_vdpa_setup_vq_irq() which is problematic as we don't know if the
token pointer is still valid or not.
Actually, we use the eventfd_ctx as the token so the life cycle of the
token should be bound to the VHOST_SET_VRING_CALL instead of
vhost_vdpa_setup_vq_irq() which could be called by set_status().
Fixing this by setting up irq bypass producer's token when handling
VHOST_SET_VRING_CALL and un-registering the producer before calling
vhost_vring_ioctl() to prevent a possible use after free as eventfd
could have been released in vhost_vring_ioctl(). And such registering
and unregistering will only be done if DRIVER_OK is set.
Reported-by: Dragos Tatulea <dtatulea@nvidia.com>
Tested-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Fixes: 2cf1ba9a4d ("vhost_vdpa: implement IRQ offloading in vhost_vdpa")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20240816031900.18013-1-jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Pull virtio fix from Michael Tsirkin:
"Fix a single, long-standing issue with kick pass-through vdpa"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost-vdpa: switch to use vmf_insert_pfn() in the fault handler
Introduce support for virtio_transport_unsent_bytes
ioctl for virtio_transport, vhost_vsock and vsock_loopback.
For all transports the unsent bytes counter is incremented
in virtio_transport_get_credit.
In virtio_transport (G2H) and in vhost-vsock (H2G) the counter
is decremented when the skbuff is consumed. In vsock_loopback the
same skbuff is passed from the transmitter to the receiver, so
the counter is decremented before queuing the skbuff to the
receiver.
Signed-off-by: Luigi Leonardi <luigi.leonardi@outlook.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remap_pfn_page() should not be called in the fault handler as it may
change the vma->flags which may trigger lockdep warning since the vma
write lock is not held. Actually there's no need to modify the
vma->flags as it has been set in the mmap(). So this patch switches to
use vmf_insert_pfn() instead.
Reported-by: Dragos Tatulea <dtatulea@nvidia.com>
Tested-by: Dragos Tatulea <dtatulea@nvidia.com>
Fixes: ddd89d0a05 ("vhost_vdpa: support doorbell mapping via mmap")
Cc: stable@vger.kernel.org
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20240701033159.18133-1-jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Pull virtio updates from Michael Tsirkin:
"Several new features here:
- Virtio find vqs API has been reworked (required to fix the
scalability issue we have with adminq, which I hope to merge later
in the cycle)
- vDPA driver for Marvell OCTEON
- virtio fs performance improvement
- mlx5 migration speedups
Fixes, cleanups all over the place"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (56 commits)
virtio: rename virtio_find_vqs_info() to virtio_find_vqs()
virtio: remove unused virtio_find_vqs() and virtio_find_vqs_ctx() helpers
virtio: convert the rest virtio_find_vqs() users to virtio_find_vqs_info()
virtio_balloon: convert to use virtio_find_vqs_info()
virtiofs: convert to use virtio_find_vqs_info()
scsi: virtio_scsi: convert to use virtio_find_vqs_info()
virtio_net: convert to use virtio_find_vqs_info()
virtio_crypto: convert to use virtio_find_vqs_info()
virtio_console: convert to use virtio_find_vqs_info()
virtio_blk: convert to use virtio_find_vqs_info()
virtio: rename find_vqs_info() op to find_vqs()
virtio: remove the original find_vqs() op
virtio: call virtio_find_vqs_info() from virtio_find_single_vq() directly
virtio: convert find_vqs() op implementations to find_vqs_info()
virtio_pci: convert vp_*find_vqs() ops to find_vqs_info()
virtio: introduce virtio_queue_info struct and find_vqs_info() config op
virtio: make virtio_find_single_vq() call virtio_find_vqs()
virtio: make virtio_find_vqs() call virtio_find_vqs_ctx()
caif_virtio: use virtio_find_single_vq() for single virtqueue finding
vdpa/mlx5: Don't enable non-active VQs in .set_vq_ready()
...
All callers of vhost_get_avail_idx() use smp_rmb() to
order the available ring entry read and avail_idx read.
Make vhost_get_avail_idx() call smp_rmb() itself whenever the avail_idx
is accessed. This way, the callers don't need to worry about the memory
barrier. As a side benefit, we also validate the index on all paths now,
which will hopefully help prevent/catch earlier future bugs.
Note that current code is inconsistent in how the errors are handled.
They are treated as an empty ring in some places, but as non-empty
ring in other places. This patch doesn't attempt to change the existing
behaviour.
No functional change intended.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Acked-by: Will Deacon <will@kernel.org>
Message-Id: <20240429232748.642356-1-gshan@redhat.com>
There are two issues around seqpacket_allow:
1. seqpacket_allow is not initialized when socket is
created. Thus if features are never set, it will be
read uninitialized.
2. if VIRTIO_VSOCK_F_SEQPACKET is set and then cleared,
then seqpacket_allow will not be cleared appropriately
(existing apps I know about don't usually do this but
it's legal and there's no way to be sure no one relies
on this).
To fix:
- initialize seqpacket_allow after allocation
- set it unconditionally in set_features
Reported-by: syzbot+6c21aeb59d0e82eb2782@syzkaller.appspotmail.com
Reported-by: Jeongjun Park <aha310510@gmail.com>
Fixes: ced7b71371 ("vhost/vsock: support SEQPACKET for transport").
Tested-by: Arseny Krasnov <arseny.krasnov@kaspersky.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20240422100010-mutt-send-email-mst@kernel.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Pull virtio updates from Michael Tsirkin:
"Several new features here:
- virtio-net is finally supported in vduse
- virtio (balloon and mem) interaction with suspend is improved
- vhost-scsi now handles signals better/faster
And fixes, cleanups all over the place"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (48 commits)
virtio-pci: Check if is_avq is NULL
virtio: delete vq in vp_find_vqs_msix() when request_irq() fails
MAINTAINERS: add Eugenio Pérez as reviewer
vhost-vdpa: Remove usage of the deprecated ida_simple_xx() API
vp_vdpa: don't allocate unused msix vectors
sound: virtio: drop owner assignment
fuse: virtio: drop owner assignment
scsi: virtio: drop owner assignment
rpmsg: virtio: drop owner assignment
nvdimm: virtio_pmem: drop owner assignment
wifi: mac80211_hwsim: drop owner assignment
vsock/virtio: drop owner assignment
net: 9p: virtio: drop owner assignment
net: virtio: drop owner assignment
net: caif: virtio: drop owner assignment
misc: nsm: drop owner assignment
iommu: virtio: drop owner assignment
drm/virtio: drop owner assignment
gpio: virtio: drop owner assignment
firmware: arm_scmi: virtio: drop owner assignment
...
In the next patches where the worker can be killed while in use, we
need to be able to take the worker mutex and kill queued works for
new IO and flushes, and set some new flags to prevent new
__vhost_vq_attach_worker calls from swapping in/out killed workers.
If we are holding the worker mutex during a flush and the flush's work
is still in the queue, the worker code that will handle the SIGKILL
cleanup won't be able to take the mutex and perform it's cleanup. So
this patch has us drop the worker mutex while waiting for the flush
to complete.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Message-Id: <20240316004707.45557-8-michael.christie@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
__vhost_vq_attach_worker uses the vhost_dev mutex to serialize the
swapping of a virtqueue's worker. This was done for simplicity because
we are already holding that mutex.
In the next patches where the worker can be killed while in use, we need
finer grained locking because some drivers will hold the vhost_dev mutex
while flushing. However in the SIGKILL handler in the next patches, we
will need to be able to swap workers (set current one to NULL), kill
queued works and stop new flushes while flushes are in progress.
To prepare us, this has us use the virtqueue mutex for swapping workers
instead of the vhost_dev one.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Message-Id: <20240316004707.45557-7-michael.christie@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vhost_vq_work_queue will never fail when queueing the TMF's response
handling because a guest can only send us TMFs when the device is fully
setup so there is always a worker at that time. In the next patches we
will modify the worker code so it handles SIGKILL by exiting before
outstanding commands/TMFs have sent their responses. In that case
vhost_vq_work_queue can fail when we try to send a response.
This has us just free the TMF's resources since at this time the guest
won't be able to get a response even if we could send it.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Message-Id: <20240316004707.45557-6-michael.christie@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We flush all the workers that are not also used by the ctl vq to make
sure that responses queued by LIO before the TMF response are sent
before the TMF response. This requires a special vhost_vq_flush
function which, in the next patches where we handle SIGKILL killing
workers while in use, will require extra locking/complexity. To avoid
that, this patch has us flush the entire device from the system work
queue, then queue up sending the response from there.
This is a little less optimal since we now flush all workers but this
will be ok since commands have already timed out and perf is not a
concern.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Message-Id: <20240316004707.45557-4-michael.christie@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In the next patches we will support the vhost_task being killed while in
use. The problem for vhost-scsi is that we can't free some structs until
we get responses for commands we have submitted to the target layer and
we currently process the responses from the vhost_task.
This has just drop the responses and free the command's resources. When
all commands have completed then operations like flush will be woken up
and we can complete device release and endpoint cleanup.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Message-Id: <20240316004707.45557-3-michael.christie@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently, we can try to queue an event's work before the vhost_task is
created. When this happens we just drop it in vhost_scsi_do_plug before
even calling vhost_vq_work_queue. During a device shutdown we do the
same thing after vhost_scsi_clear_endpoint has cleared the backends.
In the next patches we will be able to kill the vhost_task before we
have cleared the endpoint. In that case, vhost_vq_work_queue can fail
and we will leak the event's memory. This has handle the failure by
just freeing the event. This is safe to do, because
vhost_vq_work_queue will only return failure for us when the vhost_task
is killed and so userspace will not be able to handle events if we
sent them.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Message-Id: <20240316004707.45557-2-michael.christie@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A smp_rmb() has been missed in vhost_enable_notify(), inspired by
Will. Otherwise, it's not ensured the available ring entries pushed
by guest can be observed by vhost in time, leading to stale available
ring entries fetched by vhost in vhost_get_vq_desc(), as reported by
Yihuang Yu on NVidia's grace-hopper (ARM64) platform.
/home/gavin/sandbox/qemu.main/build/qemu-system-aarch64 \
-accel kvm -machine virt,gic-version=host -cpu host \
-smp maxcpus=1,cpus=1,sockets=1,clusters=1,cores=1,threads=1 \
-m 4096M,slots=16,maxmem=64G \
-object memory-backend-ram,id=mem0,size=4096M \
: \
-netdev tap,id=vnet0,vhost=true \
-device virtio-net-pci,bus=pcie.8,netdev=vnet0,mac=52:54:00:f1:26:b0
:
guest# netperf -H 10.26.1.81 -l 60 -C -c -t UDP_STREAM
virtio_net virtio0: output.0:id 100 is not a head!
Add the missed smp_rmb() in vhost_enable_notify(). When it returns true,
it means there's still pending tx buffers. Since it might read indices,
so it still can bypass the smp_rmb() in vhost_get_vq_desc(). Note that
it should be safe until vq->avail_idx is changed by commit d3bb267bbd
("vhost: cache avail index in vhost_enable_notify()").
Fixes: d3bb267bbd ("vhost: cache avail index in vhost_enable_notify()")
Cc: <stable@kernel.org> # v5.18+
Reported-by: Yihuang Yu <yihyu@redhat.com>
Suggested-by: Will Deacon <will@kernel.org>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20240328002149.1141302-3-gshan@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
A smp_rmb() has been missed in vhost_vq_avail_empty(), spotted by
Will. Otherwise, it's not ensured the available ring entries pushed
by guest can be observed by vhost in time, leading to stale available
ring entries fetched by vhost in vhost_get_vq_desc(), as reported by
Yihuang Yu on NVidia's grace-hopper (ARM64) platform.
/home/gavin/sandbox/qemu.main/build/qemu-system-aarch64 \
-accel kvm -machine virt,gic-version=host -cpu host \
-smp maxcpus=1,cpus=1,sockets=1,clusters=1,cores=1,threads=1 \
-m 4096M,slots=16,maxmem=64G \
-object memory-backend-ram,id=mem0,size=4096M \
: \
-netdev tap,id=vnet0,vhost=true \
-device virtio-net-pci,bus=pcie.8,netdev=vnet0,mac=52:54:00:f1:26:b0
:
guest# netperf -H 10.26.1.81 -l 60 -C -c -t UDP_STREAM
virtio_net virtio0: output.0:id 100 is not a head!
Add the missed smp_rmb() in vhost_vq_avail_empty(). When tx_can_batch()
returns true, it means there's still pending tx buffers. Since it might
read indices, so it still can bypass the smp_rmb() in vhost_get_vq_desc().
Note that it should be safe until vq->avail_idx is changed by commit
275bf960ac ("vhost: better detection of available buffers").
Fixes: 275bf960ac ("vhost: better detection of available buffers")
Cc: <stable@kernel.org> # v4.11+
Reported-by: Yihuang Yu <yihyu@redhat.com>
Suggested-by: Will Deacon <will@kernel.org>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20240328002149.1141302-2-gshan@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Pull virtio updates from Michael Tsirkin:
- Per vq sizes in vdpa
- Info query for block devices support in vdpa
- DMA sync callbacks in vduse
- Fixes, cleanups
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (35 commits)
virtio_net: rename free_old_xmit_skbs to free_old_xmit
virtio_net: unify the code for recycling the xmit ptr
virtio-net: add cond_resched() to the command waiting loop
virtio-net: convert rx mode setting to use workqueue
virtio: packed: fix unmap leak for indirect desc table
vDPA: report virtio-blk flush info to user space
vDPA: report virtio-block read-only info to user space
vDPA: report virtio-block write zeroes configuration to user space
vDPA: report virtio-block discarding configuration to user space
vDPA: report virtio-block topology info to user space
vDPA: report virtio-block MQ info to user space
vDPA: report virtio-block max segments in a request to user space
vDPA: report virtio-block block-size to user space
vDPA: report virtio-block max segment size to user space
vDPA: report virtio-block capacity to user space
virtio: make virtio_bus const
vdpa: make vdpa_bus const
vDPA/ifcvf: implement vdpa_config_ops.get_vq_num_min
vDPA/ifcvf: get_max_vq_size to return max size
virtio_vdpa: create vqs with the actual size
...
When the Qemu launched with vhost but without tap vnet_hdr,
vhost tries to copy vnet_hdr from socket iter with size 0
to the page that may contain some trash.
That trash can be interpreted as unpredictable values for
vnet_hdr.
That leads to dropping some packets and in some cases to
stalling vhost routine when the vhost_net tries to process
packets and fails in a loop.
Qemu options:
-netdev tap,vhost=on,vnet_hdr=off,...
Signed-off-by: Andrew Melnychenko <andrew@daynix.com>
Message-Id: <20240115194840.1183077-1-andrew@daynix.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The page frag in vhost_net_page_frag_refill() uses the
'struct page_frag' from skb_page_frag_refill(), but it's
implementation is similar to page_frag_alloc_align() now.
This patch removes vhost_net_page_frag_refill() by using
'struct page_frag_cache' instead of 'struct page_frag',
and allocating frag using page_frag_alloc_align().
The added benefit is that not only unifying the page frag
implementation a little, but also having about 0.5% performance
boost testing by using the vhost_net_test introduced in the
last patch.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently there seems to be three page frag implementations
which all try to allocate order 3 page, if that fails, it
then fail back to allocate order 0 page, and each of them
all allow order 3 page allocation to fail under certain
condition by using specific gfp bits.
The gfp bits for order 3 page allocation are different
between different implementation, __GFP_NOMEMALLOC is
or'd to forbid access to emergency reserves memory for
__page_frag_cache_refill(), but it is not or'd in other
implementions, __GFP_DIRECT_RECLAIM is masked off to avoid
direct reclaim in vhost_net_page_frag_refill(), but it is
not masked off in __page_frag_cache_refill().
This patch unifies the gfp bits used between different
implementions by or'ing __GFP_NOMEMALLOC and masking off
__GFP_DIRECT_RECLAIM for order 3 page allocation to avoid
possible pressure for mm.
Leave the gfp unifying for page frag implementation in sock.c
for now as suggested by Paolo Abeni.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
CC: Alexander Duyck <alexander.duyck@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Pull virtio updates from Michael Tsirkin:
- vdpa/mlx5: support for resumable vqs
- virtio_scsi: mq_poll support
- 3virtio_pmem: support SHMEM_REGION
- virtio_balloon: stay awake while adjusting balloon
- virtio: support for no-reset virtio PCI PM
- Fixes, cleanups
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vdpa/mlx5: Add mkey leak detection
vdpa/mlx5: Introduce reference counting to mrs
vdpa/mlx5: Use vq suspend/resume during .set_map
vdpa/mlx5: Mark vq state for modification in hw vq
vdpa/mlx5: Mark vq addrs for modification in hw vq
vdpa/mlx5: Introduce per vq and device resume
vdpa/mlx5: Allow modifying multiple vq fields in one modify command
vdpa/mlx5: Expose resumable vq capability
vdpa: Block vq property changes in DRIVER_OK
vdpa: Track device suspended state
scsi: virtio_scsi: Add mq_poll support
virtio_pmem: support feature SHMEM_REGION
virtio_balloon: stay awake while adjusting balloon
vdpa: Remove usage of the deprecated ida_simple_xx() API
virtio: Add support for no-reset virtio PCI PM
virtio_net: fix missing dma unmap for resize
vhost-vdpa: account iommu allocations
vdpa: Fix an error handling path in eni_vdpa_probe()
Pull networking updates from Paolo Abeni:
"The most interesting thing is probably the networking structs
reorganization and a significant amount of changes is around
self-tests.
Core & protocols:
- Analyze and reorganize core networking structs (socks, netdev,
netns, mibs) to optimize cacheline consumption and set up build
time warnings to safeguard against future header changes
This improves TCP performances with many concurrent connections up
to 40%
- Add page-pool netlink-based introspection, exposing the memory
usage and recycling stats. This helps indentify bad PP users and
possible leaks
- Refine TCP/DCCP source port selection to no longer favor even
source port at connect() time when IP_LOCAL_PORT_RANGE is set. This
lowers the time taken by connect() for hosts having many active
connections to the same destination
- Refactor the TCP bind conflict code, shrinking related socket
structs
- Refactor TCP SYN-Cookie handling, as a preparation step to allow
arbitrary SYN-Cookie processing via eBPF
- Tune optmem_max for 0-copy usage, increasing the default value to
128KB and namespecifying it
- Allow coalescing for cloned skbs coming from page pools, improving
RX performances with some common configurations
- Reduce extension header parsing overhead at GRO time
- Add bridge MDB bulk deletion support, allowing user-space to
request the deletion of matching entries
- Reorder nftables struct members, to keep data accessed by the
datapath first
- Introduce TC block ports tracking and use. This allows supporting
multicast-like behavior at the TC layer
- Remove UAPI support for retired TC qdiscs (dsmark, CBQ and ATM) and
classifiers (RSVP and tcindex)
- More data-race annotations
- Extend the diag interface to dump TCP bound-only sockets
- Conditional notification of events for TC qdisc class and actions
- Support for WPAN dynamic associations with nearby devices, to form
a sub-network using a specific PAN ID
- Implement SMCv2.1 virtual ISM device support
- Add support for Batman-avd mulicast packet type
BPF:
- Tons of verifier improvements:
- BPF register bounds logic and range support along with a large
test suite
- log improvements
- complete precision tracking support for register spills
- track aligned STACK_ZERO cases as imprecise spilled registers.
This improves the verifier "instructions processed" metric from
single digit to 50-60% for some programs
- support for user's global BPF subprogram arguments with few
commonly requested annotations for a better developer
experience
- support tracking of BPF_JNE which helps cases when the compiler
transforms (unsigned) "a > 0" into "if a == 0 goto xxx" and the
like
- several fixes
- Add initial TX metadata implementation for AF_XDP with support in
mlx5 and stmmac drivers. Two types of offloads are supported right
now, that is, TX timestamp and TX checksum offload
- Fix kCFI bugs in BPF all forms of indirect calls from BPF into
kernel and from kernel into BPF work with CFI enabled. This allows
BPF to work with CONFIG_FINEIBT=y
- Change BPF verifier logic to validate global subprograms lazily
instead of unconditionally before the main program, so they can be
guarded using BPF CO-RE techniques
- Support uid/gid options when mounting bpffs
- Add a new kfunc which acquires the associated cgroup of a task
within a specific cgroup v1 hierarchy where the latter is
identified by its id
- Extend verifier to allow bpf_refcount_acquire() of a map value
field obtained via direct load which is a use-case needed in
sched_ext
- Add BPF link_info support for uprobe multi link along with bpftool
integration for the latter
- Support for VLAN tag in XDP hints
- Remove deprecated bpfilter kernel leftovers given the project is
developed in user-space (https://github.com/facebook/bpfilter)
Misc:
- Support for parellel TC self-tests execution
- Increase MPTCP self-tests coverage
- Updated the bridge documentation, including several so-far
undocumented features
- Convert all the net self-tests to run in unique netns, to avoid
random failures due to conflict and allow concurrent runs
- Add TCP-AO self-tests
- Add kunit tests for both cfg80211 and mac80211
- Autogenerate Netlink families documentation from YAML spec
- Add yml-gen support for fixed headers and recursive nests, the tool
can now generate user-space code for all genetlink families for
which we have specs
- A bunch of additional module descriptions fixes
- Catch incorrect freeing of pages belonging to a page pool
Driver API:
- Rust abstractions for network PHY drivers; do not cover yet the
full C API, but already allow implementing functional PHY drivers
in rust
- Introduce queue and NAPI support in the netdev Netlink interface,
allowing complete access to the device <> NAPIs <> queues
relationship
- Introduce notifications filtering for devlink to allow control
application scale to thousands of instances
- Improve PHY validation, requesting rate matching information for
each ethtool link mode supported by both the PHY and host
- Add support for ethtool symmetric-xor RSS hash
- ACPI based Wifi band RFI (WBRF) mitigation feature for the AMD
platform
- Expose pin fractional frequency offset value over new DPLL generic
netlink attribute
- Convert older drivers to platform remove callback returning void
- Add support for PHY package MMD read/write
New hardware / drivers:
- Ethernet:
- Octeon CN10K devices
- Broadcom 5760X P7
- Qualcomm SM8550 SoC
- Texas Instrument DP83TG720S PHY
- Bluetooth:
- IMC Networks Bluetooth radio
Removed:
- WiFi:
- libertas 16-bit PCMCIA support
- Atmel at76c50x drivers
- HostAP ISA/PCMCIA style 802.11b driver
- zd1201 802.11b USB dongles
- Orinoco ISA/PCMCIA 802.11b driver
- Aviator/Raytheon driver
- Planet WL3501 driver
- RNDIS USB 802.11b driver
Driver updates:
- Ethernet high-speed NICs:
- Intel (100G, ice, idpf):
- allow one by one port representors creation and removal
- add temperature and clock information reporting
- add get/set for ethtool's header split ringparam
- add again FW logging
- adds support switchdev hardware packet mirroring
- iavf: implement symmetric-xor RSS hash
- igc: add support for concurrent physical and free-running
timers
- i40e: increase the allowable descriptors
- nVidia/Mellanox:
- Preparation for Socket-Direct multi-dev netdev. That will
allow in future releases combining multiple PFs devices
attached to different NUMA nodes under the same netdev
- Broadcom (bnxt):
- TX completion handling improvements
- add basic ntuple filter support
- reduce MSIX vectors usage for MQPRIO offload
- add VXLAN support, USO offload and TX coalesce completion
for P7
- Marvell Octeon EP:
- xmit-more support
- add PF-VF mailbox support and use it for FW notifications
for VFs
- Wangxun (ngbe/txgbe):
- implement ethtool functions to operate pause param, ring
param, coalesce channel number and msglevel
- Netronome/Corigine (nfp):
- add flow-steering support
- support UDP segmentation offload
- Ethernet NICs embedded, slower, virtual:
- Xilinx AXI: remove duplicate DMA code adopting the dma engine
driver
- stmmac: add support for HW-accelerated VLAN stripping
- TI AM654x sw: add mqprio, frame preemption & coalescing
- gve: add support for non-4k page sizes.
- virtio-net: support dynamic coalescing moderation
- nVidia/Mellanox Ethernet datacenter switches:
- allow firmware upgrade without a reboot
- more flexible support for bridge flooding via the compressed
FID flooding mode
- Ethernet embedded switches:
- Microchip:
- fine-tune flow control and speed configurations in KSZ8xxx
- KSZ88X3: enable setting rmii reference
- Renesas:
- add jumbo frames support
- Marvell:
- 88E6xxx: add "eth-mac" and "rmon" stats support
- Ethernet PHYs:
- aquantia: add firmware load support
- at803x: refactor the driver to simplify adding support for more
chip variants
- NXP C45 TJA11xx: Add MACsec offload support
- Wifi:
- MediaTek (mt76):
- NVMEM EEPROM improvements
- mt7996 Extremely High Throughput (EHT) improvements
- mt7996 Wireless Ethernet Dispatcher (WED) support
- mt7996 36-bit DMA support
- Qualcomm (ath12k):
- support for a single MSI vector
- WCN7850: support AP mode
- Intel (iwlwifi):
- new debugfs file fw_dbg_clear
- allow concurrent P2P operation on DFS channels
- Bluetooth:
- QCA2066: support HFP offload
- ISO: more broadcast-related improvements
- NXP: better recovery in case receiver/transmitter get out of sync"
* tag 'net-next-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1714 commits)
lan78xx: remove redundant statement in lan78xx_get_eee
lan743x: remove redundant statement in lan743x_ethtool_get_eee
bnxt_en: Fix RCU locking for ntuple filters in bnxt_rx_flow_steer()
bnxt_en: Fix RCU locking for ntuple filters in bnxt_srxclsrldel()
bnxt_en: Remove unneeded variable in bnxt_hwrm_clear_vnic_filter()
tcp: Revert no longer abort SYN_SENT when receiving some ICMP
Revert "mlx5 updates 2023-12-20"
Revert "net: stmmac: Enable Per DMA Channel interrupt"
ipvlan: Remove usage of the deprecated ida_simple_xx() API
ipvlan: Fix a typo in a comment
net/sched: Remove ipt action tests
net: stmmac: Use interrupt mode INTM=1 for per channel irq
net: stmmac: Add support for TX/RX channel interrupt
net: stmmac: Make MSI interrupt routine generic
dt-bindings: net: snps,dwmac: per channel irq
net: phy: at803x: make read_status more generic
net: phy: at803x: add support for cdt cross short test for qca808x
net: phy: at803x: refactor qca808x cable test get status function
net: phy: at803x: generalize cdt fault length function
net: ethernet: cortina: Drop TSO support
...
The virtio standard doesn't allow for virtqueue address and state
changes when the device is in DRIVER_OK. Return an error in such cases
unless the device is suspended.
The suspended device exception is needed because some devices support
virtqueue changes when the device is suspended.
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Suggested-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20231225134210.151540-3-dtatulea@nvidia.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Set vdpa device suspended state on successful suspend. Clear it on
successful resume and reset.
The state will be locked by the vhost_vdpa mutex. The mutex is taken
during suspend, resume and reset in vhost_vdpa_unlocked_ioctl. The
exception is vhost_vdpa_open which does a device reset but that should
be safe because it can only happen before the other ops.
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Suggested-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20231225134210.151540-2-dtatulea@nvidia.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Pull misc vfs updates from Christian Brauner:
"This contains the usual miscellaneous features, cleanups, and fixes
for vfs and individual fses.
Features:
- Add Jan Kara as VFS reviewer
- Show correct device and inode numbers in proc/<pid>/maps for vma
files on stacked filesystems. This is now easily doable thanks to
the backing file work from the last cycles. This comes with
selftests
Cleanups:
- Remove a redundant might_sleep() from wait_on_inode()
- Initialize pointer with NULL, not 0
- Clarify comment on access_override_creds()
- Rework and simplify eventfd_signal() and eventfd_signal_mask()
helpers
- Process aio completions in batches to avoid needless wakeups
- Completely decouple struct mnt_idmap from namespaces. We now only
keep the actual idmapping around and don't stash references to
namespaces
- Reformat maintainer entries to indicate that a given subsystem
belongs to fs/
- Simplify fput() for files that were never opened
- Get rid of various pointless file helpers
- Rename various file helpers
- Rename struct file members after SLAB_TYPESAFE_BY_RCU switch from
last cycle
- Make relatime_need_update() return bool
- Use GFP_KERNEL instead of GFP_USER when allocating superblocks
- Replace deprecated ida_simple_*() calls with their current ida_*()
counterparts
Fixes:
- Fix comments on user namespace id mapping helpers. They aren't
kernel doc comments so they shouldn't be using /**
- s/Retuns/Returns/g in various places
- Add missing parameter documentation on can_move_mount_beneath()
- Rename i_mapping->private_data to i_mapping->i_private_data
- Fix a false-positive lockdep warning in pipe_write() for watch
queues
- Improve __fget_files_rcu() code generation to improve performance
- Only notify writer that pipe resizing has finished after setting
pipe->max_usage otherwise writers are never notified that the pipe
has been resized and hang
- Fix some kernel docs in hfsplus
- s/passs/pass/g in various places
- Fix kernel docs in ntfs
- Fix kcalloc() arguments order reported by gcc 14
- Fix uninitialized value in reiserfs"
* tag 'vfs-6.8.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs: (36 commits)
reiserfs: fix uninit-value in comp_keys
watch_queue: fix kcalloc() arguments order
ntfs: dir.c: fix kernel-doc function parameter warnings
fs: fix doc comment typo fs tree wide
selftests/overlayfs: verify device and inode numbers in /proc/pid/maps
fs/proc: show correct device and inode numbers in /proc/pid/maps
eventfd: Remove usage of the deprecated ida_simple_xx() API
fs: super: use GFP_KERNEL instead of GFP_USER for super block allocation
fs/hfsplus: wrapper.c: fix kernel-doc warnings
fs: add Jan Kara as reviewer
fs/inode: Make relatime_need_update return bool
pipe: wakeup wr_wait after setting max_usage
file: remove __receive_fd()
file: stop exposing receive_fd_user()
fs: replace f_rcuhead with f_task_work
file: remove pointless wrapper
file: s/close_fd_get_file()/file_close_fd()/g
Improve __fget_files_rcu() code generation (and thus __fget_light())
file: massage cleanup of files that failed to open
fs/pipe: Fix lockdep false-positive in watchqueue pipe_write()
...
Send credit update message when SO_RCVLOWAT is updated and it is bigger
than number of bytes in rx queue. It is needed, because 'poll()' will
wait until number of bytes in rx queue will be not smaller than
O_RCVLOWAT, so kick sender to send more data. Otherwise mutual hungup
for tx/rx is possible: sender waits for free space and receiver is
waiting data in 'poll()'.
Rename 'set_rcvlowat' callback to 'notify_set_rcvlowat' and set
'sk->sk_rcvlowat' only in one place (i.e. 'vsock_set_rcvlowat'), so the
transport doesn't need to do it.
Fixes: b89d882dc9 ("vsock/virtio: reduce credit update messages")
Signed-off-by: Arseniy Krasnov <avkrasnov@salutedevices.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
