[ Upstream commit 4ca651df07 ]
The existing logic in tcphy_get_mode() can cause the phy to be
incorrectly configured to USB UFP or DisplayPort mode when
extcon_get_state returns an error code.
extcon_get_state() can return 0, 1, or a negative error code.
It is possible to get into the failing state with an extcon driver
which does not support the extcon connector id specified as the
second argument to extcon_get_state().
tcphy_get_mode()
->extcon_get_state()
-->find_cable_index_by_id()
--->return -EINVAL;
Fixes: e96be45cb8 ("phy: Add USB Type-C PHY driver for rk3399")
Signed-off-by: Neill Kapron <nkapron@google.com>
Reviewed-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230126001013.3707873-1-nkapron@google.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17eee264ef ]
sp_usb_phy_probe() will call platform_get_resource_byname() that may fail
and return NULL. devm_ioremap() will use usbphy->moon4_res_mem->start as
input, which may causes null-ptr-deref. Check the ret value of
platform_get_resource_byname() to avoid the null-ptr-deref.
Fixes: 99d9ccd973 ("phy: usb: Add USB2.0 phy driver for Sunplus SP7021")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Link: https://lore.kernel.org/r/20221125021222.25687-1-shangxiaojing@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a7d86d14d ]
The PHY is powered on during phy-init by setting the SW_PWRDN bit in the
COM_POWER_DOWN_CTRL register and then setting the same bit in the in the
PCS_POWER_DOWN_CONTROL register that belongs to the USB part of the
PHY.
Currently, whether power on succeeds depends on probe order and having
the USB part of the PHY be initialised first. In case the DP part of the
PHY is instead initialised first, the intended power on of the USB block
results in a corrupted DP_PHY register (e.g. DP_PHY_AUX_CFG8).
Add a pointer to the USB part of the PHY to the driver data and use that
to power on the PHY also if the DP part of the PHY is initialised first.
Fixes: 52e013d0bf ("phy: qcom-qmp: Add support for DP in USB3+DP combo phy")
Cc: stable@vger.kernel.org # 5.10
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221114081346.5116-5-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f60740652 ]
The USB PHY used in the Allwinner H616 SoC inherits some traits from its
various predecessors: it has four full PHYs like the H3, needs some
extra bits to be set like the H6, and puts SIDDQ on a different bit like
the A100. Plus it needs this weird PHY2 quirk.
Name all those properties in a new config struct and assign a new
compatible name to it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20221031111358.3387297-5-andre.przywara@arm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b45c6d8032 ]
At least the Allwinner H616 SoC requires a weird quirk to make most
USB PHYs work: Only port2 works out of the box, but all other ports
need some help from this port2 to work correctly: The CLK_BUS_PHY2 and
RST_USB_PHY2 clock and reset need to be enabled, and the SIDDQ bit in
the PMU PHY control register needs to be cleared. For this register to
be accessible, CLK_BUS_ECHI2 needs to be ungated. Don't ask ....
Instead of disguising this as some generic feature, treat it more like
a quirk (what it really is):
If the quirk bit is set, and we initialise a PHY other than PHY2, ungate
this one special clock, and clear the SIDDQ bit. We also pick the clock
and reset from PHY2 and enable them as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20221031111358.3387297-4-andre.przywara@arm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11bf53a38c ]
The PCIe QMP PHY requires different programming sequences when being
used for the RC (Root Complex) or for the EP (End Point) modes. Allow
selecting the submode and thus selecting a set of PHY programming
tables.
Since the RC and EP modes share common some common init sequence, the
common sequence is kept in the main table and the sequence differences
are pushed to the extra tables.
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220927092207.161501-3-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stable-dep-of: 9ddcd920f8 ("phy: qcom-qmp-pcie: Fix high latency with 4x2 PHY when ASPM is enabled")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2584068a9e ]
Commit af6643242d ("phy: qcom-qmp-pcie: split pcs_misc region for ipq6018
pcie gen3") reworked the pcs regs values and removed the 0x400 offset
for each pcs_misc regs.
This change caused the malfunction of ipq8074 downstream since it still
has the legacy pcs table where pcs_misc are not placed on a different
table and instead put together assuming the offset of 0x400 for the
related pcs_misc regs.
Split pcs_misc init cfg from the ipq8074 pcs init table to be handled
correctly to prepare for actual support for gen3 pcie for ipq8074.
Fixes: af6643242d ("phy: qcom-qmp-pcie: split pcs_misc region for ipq6018 pcie gen3")
Reported-by: Robert Marko <robimarko@gmail.com>
Tested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20221103212125.17156-1-ansuelsmth@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2566ad8ec4 ]
SM8250 configuration tables are split into two parts: the common one and
the PHY-specific tables. Make this split more formal. Rather than having
a blind renamed copy of all QMP table fields, add separate struct
qmp_phy_cfg_tables and add two instances of this structure to the struct
qmp_phy_cfg. Later on this will be used to support different PHY modes
(RC vs EP).
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220927092207.161501-2-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stable-dep-of: 2584068a9e ("phy: qcom-qmp-pcie: split pcs_misc init cfg for ipq8074 pcs table")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c6b3af390 ]
The PCS_USB register block lives at an offset of 0x1000 from the PCS
region on SC8280XP so add the missing offset to avoid corrupting
unrelated registers on runtime suspend.
Note that the current binding is broken as it does not describe the
PCS_USB region and the PCS register size does not cover PCS_USB and the
regions in between. As Linux currently maps full pages, simply adding
the offset to driver works until the binding has been fixed.
Fixes: c0c7769cda ("phy: qcom-qmp: Add SC8280XP USB3 UNI phy")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221028160435.26948-2-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38cd167d1f ]
The power-down delay was included in the first version of the QMP driver
as an optional delay after powering on the PHY (using
POWER_DOWN_CONTROL) and just before starting it. Later changes modified
this sequence by powering on before initialising the PHY, but the
optional delay stayed where it was (i.e. before starting the PHY).
The vendor driver does not use a delay before starting the PHY and this
is likely not needed on any platform unless there is a corresponding
delay in the vendor kernel init sequence tables (i.e. in devicetree).
Let's keep the delay for now, but drop the redundant delay period
configuration while increasing the unnecessarily low timer slack
somewhat.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221012081241.18273-15-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stable-dep-of: 922adfd59e ("phy: qcom-qmp-usb: correct registers layout for IPQ8074 USB3 PHY")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51bd33069f ]
The power-down delay was included in the first version of the QMP driver
as an optional delay after powering on the PHY (using
POWER_DOWN_CONTROL) and just before starting it. Later changes modified
this sequence by powering on before initialising the PHY, but the
optional delay stayed where it was (i.e. before starting the PHY).
The vendor driver does not use a delay before starting the PHY and this
is likely not needed on any platform unless there is a corresponding
delay in the vendor kernel init sequence tables (i.e. in devicetree).
But as the vendor kernel do have a 1 ms delay *after* starting the PHY
and before starting to poll the status it is possible that later
contributors have simply not noticed that the mainline power-down delay
is not equivalent.
As the current delay before even starting the PHY is pretty much
pointless and likely a mistake, move the delay after starting the PHY
which avoids a few iterations of polling and speeds up startup by 1 ms
(the poll loop otherwise takes about 1.8 ms).
Note that MSM8998 has never used a power-down delay so add a flag to
skip the delay in case starting the PHY is faster on MSM8998. This can
be removed after someone takes a measurement.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221012081241.18273-10-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stable-dep-of: 4a9eac5ae2 ("phy: qcom-qmp-pcie: fix sc8180x initialisation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e71906144b ]
The power-down delay was included in the first version of the QMP driver
as an optional delay after powering on the PHY (using
POWER_DOWN_CONTROL) and just before starting it. Later changes modified
this sequence by powering on before initialising the PHY, but the
optional delay stayed where it was (i.e. before starting the PHY).
The vendor driver does not use a delay before starting the PHY and this
is likely not needed on any platform unless there is a corresponding
delay in the vendor kernel init sequence tables (i.e. in devicetree).
Let's keep the delay for now, but drop the redundant delay period
configuration while increasing the unnecessarily low timer slack
somewhat.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221012081241.18273-9-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stable-dep-of: 4a9eac5ae2 ("phy: qcom-qmp-pcie: fix sc8180x initialisation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d93887cb4 ]
Since commit 0d58280cf1 ("phy: Update PHY power control sequence") the
PHY is powered on before configuring the registers and only the MSM8996
PCIe PHY, which includes the POWER_DOWN_CONTROL register in its PCS
initialisation table, may possibly require a second update afterwards.
To make things worse, the POWER_DOWN_CONTROL register lies at a
different offset on more recent SoCs so that the second update, which
still used a hard-coded offset, would write to an unrelated register
(e.g. a revision-id register on SC8280XP).
As the MSM8996 PCIe PHY is now handled by a separate driver, simply drop
the bogus register update.
Fixes: e4d8b05ad5 ("phy: qcom-qmp: Use proper PWRDOWN offset for sm8150 USB") added support
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> #RB3
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221017065013.19647-12-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b01d622d76 ]
Turris MOX board with older ARM Trusted Firmware version v1.5 is not able
to detect any USB 3.0 device connected to USB-A port on Mox-A module after
commit 0a6fc70d76 ("phy: marvell: phy-mvebu-a3700-comphy: Remove broken
reset support"). On the other hand USB 2.0 devices connected to the same
USB-A port are working fine.
It looks as if the older firmware configures COMPHY registers for USB 3.0
somehow incompatibly for kernel driver. Experiments show that resetting
COMPHY registers via setting SFT_RST auto-clearing bit in COMPHY_SFT_RESET
register fixes this issue.
Reset the COMPHY in mvebu_a3700_comphy_usb3_power_on() function as a first
step after selecting COMPHY lane and USB 3.0 function. With this change
Turris MOX board can successfully detect USB 3.0 devices again.
Before the above mentioned commit this reset was implemented in PHY reset
method, so this is the reason why there was no issue with older firmware
version then.
Fixes: 0a6fc70d76 ("phy: marvell: phy-mvebu-a3700-comphy: Remove broken reset support")
Reported-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20220920121154.30115-1-pali@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit fc64623637 ("phy: qcom-qmp-combo,usb: add support for separate
PCS_USB region") started treating the PCS_USB registers as potentially
separate from the PCS registers but used the wrong base when no PCS_USB
offset has been provided.
Fix the PCS_USB base used at runtime resume to prevent dereferencing a
NULL pointer on platforms that do not provide a PCS_USB offset (e.g.
SC7180).
Fixes: fc64623637 ("phy: qcom-qmp-combo,usb: add support for separate PCS_USB region")
Cc: stable@vger.kernel.org # 5.20
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20221026162116.26462-1-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit a88520bfc0 ("usb: gadget: tegra: Reduce pad power") added calls
to tegra_phy_xusb_utmi_pad_power_on/down in the Tegra XUDC driver to
control the pad power. This change is causing a kernel panic when
powering down the pads on entering suspend with the Jetson TX2 platform.
The panic occurs because the 'xudc->curr_utmi_phy' is not configured on
this platform and we do not check to see if the pointer is valid before
attempting to deference the pointer. Fix this by checking to see if the
'phy' pointer passed to tegra_phy_xusb_utmi_pad_power_on/down is valid.
Fixes: a88520bfc0 ("usb: gadget: tegra: Reduce pad power")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20221010135132.30809-1-jonathanh@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
EJ Hsu
Johan Hovold
Neil Armstrong
Alain Volmat
Siddharth Vadapalli
Gaosheng Cui
Dmitry Baryshkov
Florian Fainelli
Jiapeng Chong
Neill Kapron
Chunfeng Yun
Geert Uytterhoeven
Shang XiaoJing
Randy Dunlap
Andre Przywara
Manivannan Sadhasivam
Christian Marangi
Justin Chen
Al Cooper
Pali Rohár
John Thomson
Peng Wu
Jon Hunter