[ Upstream commit b5ff74c1ef ]
For a physical PCI device that is passed through to a Hyper-V guest VM,
current code specifies the VMBus ring buffer size as 4 pages. But this
is an inappropriate dependency, since the amount of ring buffer space
needed is unrelated to PAGE_SIZE. For example, on x86 the ring buffer
size ends up as 16 Kbytes, while on ARM64 with 64 Kbyte pages, the ring
size bloats to 256 Kbytes. The ring buffer for PCI pass-thru devices
is used for only a few messages during device setup and removal, so any
space above a few Kbytes is wasted.
Fix this by declaring the ring buffer size to be a fixed 16 Kbytes.
Furthermore, use the VMBUS_RING_SIZE() macro so that the ring buffer
header is properly accounted for, and so the size is rounded up to a
page boundary, using the page size for which the kernel is built. While
w/64 Kbyte pages this results in a 64 Kbyte ring buffer header plus a
64 Kbyte ring buffer, that's the smallest possible with that page size.
It's still 128 Kbytes better than the current code.
Link: https://lore.kernel.org/linux-pci/20240216202240.251818-1-mhklinux@outlook.com
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Ilpo Jarvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Long Li <longli@microsoft.com>
Cc: <stable@vger.kernel.org> # 5.15.x
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72e34b8593 ]
The commit message in commit fc9a77040b ("PCI: designware-ep: Configure
Resizable BAR cap to advertise the smallest size") claims that it modifies
the Resizable BAR capability to only advertise support for 1 MB size BARs.
However, the commit writes all zeroes to PCI_REBAR_CAP (the register which
contains the possible BAR sizes that a BAR be resized to).
According to the spec, it is illegal to not have a bit set in
PCI_REBAR_CAP, and 1 MB is the smallest size allowed.
Set bit 4 in PCI_REBAR_CAP, so that we actually advertise support for a
1 MB BAR size.
Before:
Capabilities: [2e8 v1] Physical Resizable BAR
BAR 0: current size: 1MB
BAR 1: current size: 1MB
BAR 2: current size: 1MB
BAR 3: current size: 1MB
BAR 4: current size: 1MB
BAR 5: current size: 1MB
After:
Capabilities: [2e8 v1] Physical Resizable BAR
BAR 0: current size: 1MB, supported: 1MB
BAR 1: current size: 1MB, supported: 1MB
BAR 2: current size: 1MB, supported: 1MB
BAR 3: current size: 1MB, supported: 1MB
BAR 4: current size: 1MB, supported: 1MB
BAR 5: current size: 1MB, supported: 1MB
Fixes: fc9a77040b ("PCI: designware-ep: Configure Resizable BAR cap to advertise the smallest size")
Link: https://lore.kernel.org/linux-pci/20240307111520.3303774-1-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org> # 5.2
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf79e33cdd ]
Qcom SoCs making use of ARM SMMU require BDF to SID translation table in
the driver to properly map the SID for the PCIe devices based on their BDF
identifier. This is currently achieved with the help of
qcom_pcie_config_sid_1_9_0() function for SoCs supporting the 1_9_0 config.
But With newer Qcom SoCs starting from SM8450, BDF to SID translation is
set to bypass mode by default in hardware. Due to this, the translation
table that is set in the qcom_pcie_config_sid_1_9_0() is essentially
unused and the default SID is used for all endpoints in SoCs starting from
SM8450.
This is a security concern and also warrants swapping the DeviceID in DT
while using the GIC ITS to handle MSIs from endpoints. The swapping is
currently done like below in DT when using GIC ITS:
/*
* MSIs for BDF (1:0.0) only works with Device ID 0x5980.
* Hence, the IDs are swapped.
*/
msi-map = <0x0 &gic_its 0x5981 0x1>,
<0x100 &gic_its 0x5980 0x1>;
Here, swapping of the DeviceIDs ensure that the endpoint with BDF (1:0.0)
gets the DeviceID 0x5980 which is associated with the default SID as per
the iommu mapping in DT. So MSIs were delivered with IDs swapped so far.
But this also means the Root Port (0:0.0) won't receive any MSIs (for PME,
AER etc...)
So let's fix these issues by clearing the BDF to SID bypass mode for all
SoCs making use of the 1_9_0 config. This allows the PCIe devices to use
the correct SID, thus avoiding the DeviceID swapping hack in DT and also
achieving the isolation between devices.
Fixes: 4c93988221 ("PCI: qcom: Add support for configuring BDF to SID mapping for SM8250")
Link: https://lore.kernel.org/linux-pci/20240307-pci-bdf-sid-fix-v1-1-9423a7e2d63c@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: stable@vger.kernel.org # 5.11
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ccc1318cf ]
When using the fls() helper, the translation table should be a power of
two; otherwise, the resulting value will not be correct.
For example, given fls(0x3e00000) - 1 = 25, the PCIe translation window
size will be set to 0x2000000 instead of the expected size 0x3e00000.
Fix the translation window by splitting the MMIO space into multiple tables
if its size is not a power of two.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20231023081423.18559-1-jianjun.wang@mediatek.com
Fixes: d3bf75b579 ("PCI: mediatek-gen3: Add MediaTek Gen3 driver for MT8192")
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c12ca110c6 ]
The PCI driver invokes the PHY APIs using the ks_pcie_enable_phy()
function. The PHY in this case is the Serdes. It is possible that the
PCI instance is configured for two lane operation across two different
Serdes instances, using one lane of each Serdes.
In such a configuration, if the reference clock for one Serdes is
provided by the other Serdes, it results in a race condition. After the
Serdes providing the reference clock is initialized by the PCI driver by
invoking its PHY APIs, it is not guaranteed that this Serdes remains
powered on long enough for the PHY APIs based initialization of the
dependent Serdes. In such cases, the PLL of the dependent Serdes fails
to lock due to the absence of the reference clock from the former Serdes
which has been powered off by the PM Core.
Fix this by obtaining reference to the PHYs before invoking the PHY
initialization APIs and releasing reference after the initialization is
complete.
Link: https://lore.kernel.org/linux-pci/20230927041845.1222080-1-s-vadapalli@ti.com
Fixes: 49229238ab ("PCI: keystone: Cleanup PHY handling")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2217fffcd6 upstream.
Commit 6f5e193bfb ("PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get
correct MSI-X table address") modified dw_pcie_ep_raise_msix_irq() to
support iATUs which require a specific alignment.
However, this support cannot have been properly tested.
The whole point is for the iATU to map an address that is aligned,
using dw_pcie_ep_map_addr(), and then let the writel() write to
ep->msi_mem + aligned_offset.
Thus, modify the address that is mapped such that it is aligned.
With this change, dw_pcie_ep_raise_msix_irq() matches the logic in
dw_pcie_ep_raise_msi_irq().
Link: https://lore.kernel.org/linux-pci/20231128132231.2221614-1-nks@flawful.org
Fixes: 6f5e193bfb ("PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get correct MSI-X table address")
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org # 5.7
Cc: Kishon Vijay Abraham I <kishon@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef61a04057 upstream.
This is a partial revert of 8b3517f88f ("PCI: loongson: Prevent LS7A MRRS
increases") for MIPS-based Loongson.
Some MIPS Loongson systems don't support arbitrary Max_Read_Request_Size
(MRRS) settings. 8b3517f88f ("PCI: loongson: Prevent LS7A MRRS
increases") worked around that by (1) assuming that firmware configured
MRRS to the maximum supported value and (2) preventing the PCI core from
increasing MRRS.
Unfortunately, some firmware doesn't set that maximum MRRS correctly, which
results in devices not being initialized correctly. One symptom, from the
Debian report below, is this:
ata4.00: exception Emask 0x0 SAct 0x20000000 SErr 0x0 action 0x6 frozen
ata4.00: failed command: WRITE FPDMA QUEUED
ata4.00: cmd 61/20:e8:00:f0:e1/00:00:00:00:00/40 tag 29 ncq dma 16384 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
Limit MRRS to 256 because MIPS Loongson with higher MRRS support is
considered rare.
This must be done at device enablement stage because the MRRS setting may
get lost if PCI_COMMAND_MASTER on the parent bridge is cleared, and we are
only sure parent bridge is enabled at this point.
Fixes: 8b3517f88f ("PCI: loongson: Prevent LS7A MRRS increases")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217680
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=1035587
Link: https://lore.kernel.org/r/20231201115028.84351-1-jiaxun.yang@flygoat.com
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a07d2497ed ]
The DWC core driver exposes the write_dbi2() callback for writing to the
DBI2 registers in a vendor-specific way.
On the Qcom EP platforms, the DBI_CS2 bit in the ELBI region needs to be
asserted before writing to any DBI2 registers and deasserted once done.
So, let's implement the callback for the Qcom PCIe EP driver so that the
DBI2 writes are correctly handled in the hardware.
Without this callback, the DBI2 register writes like BAR size won't go
through and as a result, the default BAR size is set for all BARs.
[kwilczynski: commit log, renamed function to match the DWC convention]
Fixes: f55fee56a6 ("PCI: qcom-ep: Add Qualcomm PCIe Endpoint controller driver")
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20231025130029.74693-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Cc: stable@vger.kernel.org # 5.16+
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 83a939f0fd upstream.
With CONFIG_PCI_EXYNOS=y and exynos_pcie_remove() marked with __exit, the
function is discarded from the driver. In this case a bound device can
still get unbound, e.g via sysfs. Then no cleanup code is run resulting in
resource leaks or worse.
The right thing to do is do always have the remove callback available.
This fixes the following warning by modpost:
WARNING: modpost: drivers/pci/controller/dwc/pci-exynos: section mismatch in reference: exynos_pcie_driver+0x8 (section: .data) -> exynos_pcie_remove (section: .exit.text)
(with ARCH=x86_64 W=1 allmodconfig).
Fixes: 340cba6092 ("pci: Add PCIe driver for Samsung Exynos")
Link: https://lore.kernel.org/r/20231001170254.2506508-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3064ef2e88 upstream.
With CONFIG_PCIE_KIRIN=y and kirin_pcie_remove() marked with __exit, the
function is discarded from the driver. In this case a bound device can
still get unbound, e.g via sysfs. Then no cleanup code is run resulting in
resource leaks or worse.
The right thing to do is do always have the remove callback available.
This fixes the following warning by modpost:
drivers/pci/controller/dwc/pcie-kirin: section mismatch in reference: kirin_pcie_driver+0x8 (section: .data) -> kirin_pcie_remove (section: .exit.text)
(with ARCH=x86_64 W=1 allmodconfig).
Fixes: 000f60db78 ("PCI: kirin: Add support for a PHY layer")
Link: https://lore.kernel.org/r/20231001170254.2506508-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 200bddbb3f upstream.
With CONFIG_PCIE_KEYSTONE=y and ks_pcie_remove() marked with __exit, the
function is discarded from the driver. In this case a bound device can
still get unbound, e.g via sysfs. Then no cleanup code is run resulting in
resource leaks or worse.
The right thing to do is do always have the remove callback available.
Note that this driver cannot be compiled as a module, so ks_pcie_remove()
was always discarded before this change and modpost couldn't warn about
this issue. Furthermore the __ref annotation also prevents a warning.
Fixes: 0c4ffcfe1f ("PCI: keystone: Add TI Keystone PCIe driver")
Link: https://lore.kernel.org/r/20231001170254.2506508-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a878a54d0 upstream.
PARF_SLV_ADDR_SPACE_SIZE_2_3_3 is used by qcom_pcie_post_init_2_3_3().
This PCIe slave address space size register offset is 0x358 but was
incorrectly changed to 0x16c by 39171b33f6 ("PCI: qcom: Remove PCIE20_
prefix from register definitions").
This prevented access to slave address space registers like iATU, etc.,
so the IPQ8074 PCIe controller was not enumerated.
Revert back to the correct 0x358 offset and remove the unused
PARF_SLV_ADDR_SPACE_SIZE_2_3_3.
Fixes: 39171b33f6 ("PCI: qcom: Remove PCIE20_ prefix from register definitions")
Link: https://lore.kernel.org/r/20230919102948.1844909-1-quic_srichara@quicinc.com
Tested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Cc: stable@vger.kernel.org # v6.4+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 551a60e122 ]
The iMSI-RX module of the DW PCIe controller provides multiple sets of
MSI_CTRL_INT_i_* registers, and each set is capable of handling 32 MSI
interrupts. However, the fu740 PCIe controller driver only enabled one set
of MSI_CTRL_INT_i_* registers, as the total number of supported interrupts
was not specified.
Set the supported number of MSI vectors to enable all the MSI_CTRL_INT_i_*
registers on the fu740 PCIe core, allowing the system to fully utilize the
available MSI interrupts.
Link: https://lore.kernel.org/r/20230807055621.2431-1-yongxuan.wang@sifive.com
Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f73eedc90b ]
During domain reset process vmd_domain_reset() clears PCI
configuration space of VMD root ports. But certain platform
has observed following errors and failed to boot.
...
DMAR: VT-d detected Invalidation Queue Error: Reason f
DMAR: VT-d detected Invalidation Time-out Error: SID ffff
DMAR: VT-d detected Invalidation Completion Error: SID ffff
DMAR: QI HEAD: UNKNOWN qw0 = 0x0, qw1 = 0x0
DMAR: QI PRIOR: UNKNOWN qw0 = 0x0, qw1 = 0x0
DMAR: Invalidation Time-out Error (ITE) cleared
The root cause is that memset_io() clears prefetchable memory base/limit
registers and prefetchable base/limit 32 bits registers sequentially.
This seems to be enabling prefetchable memory if the device disabled
prefetchable memory originally.
Here is an example (before memset_io()):
PCI configuration space for 10000:00:00.0:
86 80 30 20 06 00 10 00 04 00 04 06 00 00 01 00
00 00 00 00 00 00 00 00 00 01 01 00 00 00 00 20
00 00 00 00 01 00 01 00 ff ff ff ff 75 05 00 00
...
So, prefetchable memory is ffffffff00000000-575000fffff, which is
disabled. When memset_io() clears prefetchable base 32 bits register,
the prefetchable memory becomes 0000000000000000-575000fffff, which is
enabled and incorrect.
Here is the quote from section 7.5.1.3.9 of PCI Express Base 6.0 spec:
The Prefetchable Memory Limit register must be programmed to a smaller
value than the Prefetchable Memory Base register if there is no
prefetchable memory on the secondary side of the bridge.
This is believed to be the reason for the failure and in addition the
sequence of operation in vmd_domain_reset() is not following the PCIe
specs.
Disable the bridge window by executing a sequence of operations
borrowed from pci_disable_bridge_window() and pci_setup_bridge_io(),
that comply with the PCI specifications.
Link: https://lore.kernel.org/r/20230810215029.1177379-1-nirmal.patel@linux.intel.com
Signed-off-by: Nirmal Patel <nirmal.patel@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc8b24c28b ]
The i.MX integration for the DesignWare PCI controller has a _host_exit()
operation which undoes everything that the _host_init() operation does but
does not wire this up as the host_deinit callback for the core, or call it
in any path other than suspend. This means that if we ever unwind the
initial probe of the device, for example because it fails, the regulator
core complains that the regulators for the device were left enabled:
imx6q-pcie 33800000.pcie: iATU: unroll T, 4 ob, 4 ib, align 64K, limit 16G
imx6q-pcie 33800000.pcie: Phy link never came up
imx6q-pcie 33800000.pcie: Phy link never came up
imx6q-pcie: probe of 33800000.pcie failed with error -110
------------[ cut here ]------------
WARNING: CPU: 2 PID: 46 at drivers/regulator/core.c:2396 _regulator_put+0x110/0x128
Wire up the callback so that the core can clean up after itself.
Link: https://lore.kernel.org/r/20230731-pci-imx-regulator-cleanup-v2-1-fc8fa5c9893d@kernel.org
Tested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9cbc06049 ]
Currently, as part of the qcom_pcie_perst_deassert() function, instead
of writing the updated value to clear PARF_MSTR_AXI_CLK_EN, the variable
"val" is re-read.
This must be fixed to ensure that the master clock supplied to the MHI
bus is correctly gated during L1.1/L1.2 to save power.
Thus, replace the line that re-reads "val" with a line that writes the
updated value to the register to clear PARF_MSTR_AXI_CLK_EN.
[kwilczynski: commit log]
Fixes: c457ac029e ("PCI: qcom-ep: Gate Master AXI clock to MHI bus during L1SS")
Link: https://lore.kernel.org/linux-pci/20230627141036.11600-1-manivannan.sadhasivam@linaro.org
Reported-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8650c0c2a ]
The apple_pcie_setup_port() function computes ilog2(pcie->nvecs) to set
up the number of MSIs available for each port. However, it's called
before apple_msi_init(), which initializes pcie->nvecs.
Luckily, pcie->nvecs is part of kzalloc()-ed structure and, as such,
initialized as zero. ilog2(0) happens to be 0xffffffff which then simply
configures more MSIs in hardware than we have. This doesn't break
anything because we never hand out those vectors.
Thus, swap the order of the two calls so that the correctly initialized
value is then used.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20230311133453.63246-1-sven@svenpeter.dev
Fixes: 476c41ed45 ("PCI: apple: Implement MSI support")
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Reviewed-by: Eric Curtin <ecurtin@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ebfde1584d upstream.
After commit 4fb8e46c1b ("PCI: tegra194: Enable support for 256 Byte
payload"), we initialize MPS=256 for tegra194 Root Ports before enumerating
the hierarchy.
Consider an Endpoint that supports only MPS=128. In the default situation
(CONFIG_PCIE_BUS_DEFAULT set and no "pci=pcie_bus_*" parameter), Linux
tries to configure the MPS of every device to match the upstream bridge.
If the Endpoint is directly below the Root Port, Linux can reduce the Root
Port MPS to 128 to match the Endpoint. But if there's a switch in the
middle, Linux doesn't reduce the Root Port MPS because other devices below
the switch may already be configured with MPS larger than 128.
This scenario results in uncorrectable Malformed TLP errors if the Root
Port sends TLPs with payloads larger than 128 bytes. These errors can
be avoided by using the "pci=pcie_bus_safe" parameter, but it doesn't
seem to be a good idea to always have this parameter even for basic
functionality to work.
Revert commit 4fb8e46c1b ("PCI: tegra194: Enable support for 256 Byte
payload") so the Root Ports default to MPS=128, which all devices
support.
If peer-to-peer DMA is not required, one can use "pci=pcie_bus_perf" to
get the benefit of larger MPS settings.
[bhelgaas: commit log; kwilczynski: retain "u16 val_16" declaration at
the top, add missing acked by tag]
Fixes: 4fb8e46c1b ("PCI: tegra194: Enable support for 256 Byte payload")
Link: https://lore.kernel.org/linux-pci/20230619102604.3735001-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Cc: stable@vger.kernel.org # v6.0-rc1+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a52587e0be ]
The RK3399 PCIe endpoint controller cannot generate MSI-X IRQs.
This is documented in the RK3399 technical reference manual (TRM)
section 17.5.9 "Interrupt Support".
MSI-X capability should therefore not be advertised. Remove the
MSI-X capability by editing the capability linked-list. The
previous entry is the MSI capability, therefore get the next
entry from the MSI-X capability entry and set it as next entry
for the MSI capability. This in effect removes MSI-X from the list.
Linked list before : MSI cap -> MSI-X cap -> PCIe Device cap -> ...
Linked list now : MSI cap -> PCIe Device cap -> ...
Link: https://lore.kernel.org/r/20230418074700.1083505-11-rick.wertenbroek@gmail.com
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc73ed0f1b ]
The RK3399 PCI endpoint core has 33 windows for PCIe space, now in the
driver up to 32 fixed size (1M) windows are used and pages are allocated
and mapped accordingly. The driver first used a single window and allocated
space inside which caused translation issues (between CPU space and PCI
space) because a window can only have a single translation at a given
time, which if multiple pages are allocated inside will cause conflicts.
Now each window is a single region of 1M which will always guarantee that
the translation is not in conflict.
Set the translation register addresses for physical function. As documented
in the technical reference manual (TRM) section 17.5.5 "PCIe Address
Translation" and section 17.6.8 "Address Translation Registers Description"
Link: https://lore.kernel.org/r/20230418074700.1083505-9-rick.wertenbroek@gmail.com
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9dd3c7c4c8 upstream.
The RK3399 PCIe controller should wait until the PHY PLLs are locked.
Add poll and timeout to wait for PHY PLLs to be locked. If they cannot
be locked generate error message and jump to error handler. Accessing
registers in the PHY clock domain when PLLs are not locked causes hang
The PHY PLLs status is checked through a side channel register.
This is documented in the TRM section 17.5.8.1 "PCIe Initialization
Sequence".
Link: https://lore.kernel.org/r/20230418074700.1083505-5-rick.wertenbroek@gmail.com
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 39171b33f6 ]
The PCIE part is redundant and 20 doesn't represent anything across the
SoCs supported now. So let's get rid of the prefix.
This involves adding the IP version suffix to one definition of
PARF_SLV_ADDR_SPACE_SIZE that defines offset specific to that version.
The other definition is generic for the rest of the versions.
Also, the register PCIE20_LNK_CONTROL2_LINK_STATUS2 is not used anywhere,
hence removed.
Link: https://lore.kernel.org/r/20230316081117.14288-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Stable-dep-of: 60f0072d7f ("PCI: qcom: Use DWC helpers for modifying the read-only DBI registers")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c60738de85 ]
Smatch reported:
1. drivers/pci/controller/pci-ftpci100.c:526 faraday_pci_probe() warn:
'clk' from clk_prepare_enable() not released on lines: 442,451,462,478,512,517.
2. drivers/pci/controller/pci-ftpci100.c:526 faraday_pci_probe() warn:
'p->bus_clk' from clk_prepare_enable() not released on lines: 451,462,478,512,517.
The clock resource is obtained by devm_clk_get(), and then
clk_prepare_enable() makes the clock resource ready for use. After that,
clk_disable_unprepare() should be called to release the clock resource
when it is no longer needed. However, while doing some error handling
in faraday_pci_probe(), clk_disable_unprepare() is not called to release
clk and p->bus_clk before returning. These return lines are exactly 442,
451, 462, 478, 512, 517.
Fix this warning by replacing devm_clk_get() with devm_clk_get_enabled(),
which is equivalent to devm_clk_get() + clk_prepare_enable(). And with
devm_clk_get_enabled(), the clock will automatically be disabled,
unprepared and freed when the device is unbound from the bus.
Link: https://lore.kernel.org/r/20230508043641.23807-1-yejunyan@hust.edu.cn
Fixes: b3c433efb8 ("PCI: faraday: Fix wrong pointer passed to PTR_ERR()")
Fixes: 2eeb02b285 ("PCI: faraday: Add clock handling")
Fixes: 783a862563 ("PCI: faraday: Use pci_parse_request_of_pci_ranges()")
Fixes: d3c68e0a7e ("PCI: faraday: Add Faraday Technology FTPCI100 PCI Host Bridge driver")
Fixes: f1e8bd21e3 ("PCI: faraday: Convert IRQ masking to raw PCI config accessors")
Signed-off-by: Junyan Ye <yejunyan@hust.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b61cf04c49 ]
VMD driver can disable or enable MSI remapping by changing
VMCONFIG_MSI_REMAP register. This register needs to be set to the
default value during soft reboots. Drives failed to enumerate
when Windows boots after performing a soft reboot from Linux.
Windows doesn't support MSI remapping disable feature and stale
register value hinders Windows VMD driver initialization process.
Adding vmd_shutdown function to make sure to set the VMCONFIG
register to the default value.
Link: https://lore.kernel.org/r/20230224202811.644370-1-nirmal.patel@linux.intel.com
Fixes: ee81ee84f8 ("PCI: vmd: Disable MSI-X remapping when possible")
Signed-off-by: Nirmal Patel <nirmal.patel@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Jon Derrick <jonathan.derrick@linux.dev>
Signed-off-by: Sasha Levin <sashal@kernel.org>
