commit 423622a90a upstream.
Add a special case for gpio_count == 1 && gpio_int_idx == 0 to
goodix_add_acpi_gpio_mappings().
It seems that on newer x86/ACPI devices the reset and irq GPIOs are no
longer listed as GPIO resources instead there is only 1 GpioInt resource
and _PS0 does the whole reset sequence for us.
This means that we must call acpi_device_fix_up_power() on these devices
to ensure that the chip is reset before we try to use it.
This part was already fixed in commit 3de93e6ed2 ("Input: goodix - call
acpi_device_fix_up_power() in some cases") by adding a call to
acpi_device_fix_up_power() to the generic "Unexpected ACPI resources"
catch all.
But it turns out that this case on some hw needs some more special
handling. Specifically the firmware may bootup with the IRQ pin in
output mode. The reset sequence from ACPI _PS0 (executed by
acpi_device_fix_up_power()) should put the pin in input mode,
but the GPIO subsystem has cached the direction at bootup, causing
request_irq() to fail due to gpiochip_lock_as_irq() failure:
[ 9.119864] Goodix-TS i2c-GDIX1002:00: Unexpected ACPI resources: gpio_count 1, gpio_int_idx 0
[ 9.317443] Goodix-TS i2c-GDIX1002:00: ID 911, version: 1060
[ 9.321902] input: Goodix Capacitive TouchScreen as /devices/pci0000:00/0000:00:17.0/i2c_designware.4/i2c-5/i2c-GDIX1002:00/input/input8
[ 9.327840] gpio gpiochip0: (INT3453:00): gpiochip_lock_as_irq: tried to flag a GPIO set as output for IRQ
[ 9.327856] gpio gpiochip0: (INT3453:00): unable to lock HW IRQ 26 for IRQ
[ 9.327861] genirq: Failed to request resources for GDIX1002:00 (irq 131) on irqchip intel-gpio
[ 9.327912] Goodix-TS i2c-GDIX1002:00: request IRQ failed: -5
Fix this by adding a special case for gpio_count == 1 && gpio_int_idx == 0
which adds an ACPI GPIO lookup table for the int GPIO even though we cannot
use it for reset purposes (as there is no reset GPIO).
Adding the lookup will make the gpiod_int = gpiod_get(..., GPIOD_IN) call
succeed, which will explicitly set the direction to input fixing the issue.
Note this re-uses the acpi_goodix_int_first_gpios[] lookup table, since
there is only 1 GPIO in the ACPI resources the reset entry in that
lookup table will amount to a no-op.
Reported-and-tested-by: Michael Smith <1973.mjsmith@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231003215144.69527-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a0432bab6 upstream.
The Android Lenovo Yoga Book X90F / X90L uses the same goodix touchscreen
with 9 bytes touch reports for its touch keyboard as the already supported
Windows Lenovo Yoga Book X91F/L, add a DMI match for this to
the nine_bytes_report DMI table.
When the quirk for the X91F/L was initially added it was written to
also apply to the X90F/L but this does not work because the Android
version of the Yoga Book uses completely different DMI strings.
Also adjust the X91F/L quirk to reflect that it only applies to
the X91F/L models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20230315134442.71787-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a85fbd6498 ]
As can be seen in elants_i2c_power_off(), we want the reset GPIO
asserted when power is off. The reset GPIO is active low so we need
the reset line logic low when power is off to avoid leakage.
We have a problem, though, at probe time. At probe time we haven't
powered the regulators on yet but we have:
devm_gpiod_get(&client->dev, "reset", GPIOD_OUT_LOW);
While that _looks_ right, it turns out that it's not. The
GPIOD_OUT_LOW doesn't mean to init the GPIO to low. It means init the
GPIO to "not asserted". Since this is an active low GPIO that inits it
to be high.
Let's fix this to properly init the GPIO. Now after both probe and
power off the state of the GPIO is consistent (it's "asserted" or
level low).
Once we fix this, we can see that at power on time we no longer to
assert the reset GPIO as the first thing. The reset GPIO is _always_
asserted before powering on. Let's fix powering on to account for
this.
Fixes: afe10358e4 ("Input: elants_i2c - wire up regulator support")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20221117123805.1.I9959ac561dd6e1e8e1ce7085e4de6167b27c574f@changeid
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7e37cc624 ]
On ACPI systems (irq_pin_access_method == IRQ_PIN_ACCESS_ACPI_*) the driver
does not reset the controller at probe time, because sometimes the system
firmware loads a config and resetting might loose this config.
On the Nanote UMPC-01 device OTOH the config is in flash of the controller,
the controller needs a reset to load this; and the system firmware does not
reset the controller on a cold boot.
To fix the Nanote UMPC-01 touchscreen not working on a cold boot, try
resetting the controller and then re-reading the config when encountering
a config with 0 width/height/max_touch_num value and the controller has
not already been reset by goodix_ts_probe().
This should be safe to do in general because normally we should never
encounter a config with 0 width/height/max_touch_num. Doing this in
general not only avoids the need for a DMI quirk, but also might help
other systems.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20221025122930.421377-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2fd46cd3d ]
Unless the controller is not responding at boot or after suspend/resume,
the driver never resets the controller on x86/ACPI platforms. The driver
still requesting the reset pin at probe() though in case it needs it.
Until now the driver has always requested the reset pin with GPIOD_IN
as type. The idea being to put the pin in high-impedance mode to save
power until the driver actually wants to issue a reset.
But this means that just requesting the pin can cause issues, since
requesting it in another mode then GPIOD_ASIS may cause the pinctrl
driver to touch the pin settings. We have already had issues before
due to a bug in the pinctrl-cherryview.c driver which has been fixed in
commit 921daeeca9 ("pinctrl: cherryview: Preserve
CHV_PADCTRL1_INVRXTX_TXDATA flag on GPIOs").
And now it turns out that requesting the reset-pin as GPIOD_IN also stops
the touchscreen from working on the GPD P2 max mini-laptop. The behavior
of putting the pin in high-impedance mode relies on there being some
external pull-up to keep it high and there seems to be no pull-up on the
GPD P2 max, causing things to break.
This commit fixes this by requesting the reset pin as is when using
the x86/ACPI code paths to lookup the GPIOs; and by not dropping it
back into input-mode in case the driver does end up issuing a reset
for error-recovery.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209061
Fixes: a7d4b17166 ("Input: goodix - add support for getting IRQ + reset GPIOs on Cherry Trail devices")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211206091116.44466-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 209bda4741 ]
Refactor reset handling a bit, change the main reset handler
into a new goodix_reset_no_int_sync() helper and add a
goodix_reset() wrapper which calls goodix_int_sync()
separately.
Also push the dev_err() call on reset failure into the
goodix_reset_no_int_sync() and goodix_int_sync() functions,
so that we don't need to have separate dev_err() calls in
all their callers.
This is a preparation patch for adding support for controllers
without flash, which need to have their firmware uploaded and
need some other special handling too.
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210920150643.155872-4-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2233cb7b6 ]
Add a goodix.h header file, and move the register definitions,
and struct declarations there and add prototypes for various
helper functions.
This is a preparation patch for adding support for controllers
without flash, which need to have their firmware uploaded and
need some other special handling too.
Since MAINTAINERS needs updating because of this change anyways,
also add myself as co-maintainer.
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210920150643.155872-3-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f76955ab1 ]
The commit 26623eea0d attempted to deal with potential leak of runtime
PM counter when opening the touchscreen device, however it ended up
erroneously dropping the counter in the case of successfully enabling the
device.
Let's address this by using pm_runtime_resume_and_get() and then executing
pm_runtime_put_sync() only when we fail to send "sense on" command to the
device.
Fixes: 26623eea0d ("Input: stmfts - fix reference leak in stmfts_input_open")
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e4920d42ce upstream.
According to Ilitek "231x & ILI251x Programming Guide" Version: 2.30
"2.1. Power Sequence", "T4 Chip Reset and discharge time" is minimum
10ms and "T2 Chip initial time" is maximum 150ms. Adjust the reset
timings such that T4 is 12ms and T2 is 160ms to fit those figures.
This prevents sporadic touch controller start up failures when some
systems with at least ILI251x controller boot, without this patch
the systems sometimes fail to communicate with the touch controller.
Fixes: 201f3c8035 ("Input: ili210x - add reset GPIO support")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20220518204901.93534-1-marex@denx.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e941dc13fd ]
I observed the following problem with the BT404 touch pad
running the Phosh UI:
When e.g. typing on the virtual keyboard pressing "g" would
produce "ggg".
After some analysis it turns out the firmware reports that three
fingers hit that coordinate at the same time, finger 0, 2 and
4 (of the five available 0,1,2,3,4).
DOWN
Zinitix-TS 3-0020: finger 0 down (246, 395)
Zinitix-TS 3-0020: finger 1 up (0, 0)
Zinitix-TS 3-0020: finger 2 down (246, 395)
Zinitix-TS 3-0020: finger 3 up (0, 0)
Zinitix-TS 3-0020: finger 4 down (246, 395)
UP
Zinitix-TS 3-0020: finger 0 up (246, 395)
Zinitix-TS 3-0020: finger 2 up (246, 395)
Zinitix-TS 3-0020: finger 4 up (246, 395)
This is one touch and release: i.e. this is all reported on
touch (down) and release.
There is a field in the struct touch_event called finger_cnt
which is actually a bitmask of the fingers active in the
event.
Rename this field finger_mask as this matches the use contents
better, then use for_each_set_bit() to iterate over just the
fingers that are actally active.
Factor out a finger reporting function zinitix_report_fingers()
to handle all fingers.
Also be more careful in reporting finger down/up: we were
reporting every event with input_mt_report_slot_state(..., true);
but this should only be reported on finger down or move,
not on finger up, so also add code to check p->sub_status
to see what is happening and report correctly.
After this my Zinitix BT404 touchscreen report fingers
flawlessly.
The vendor drive I have notably does not use the "finger_cnt"
and contains obviously incorrect code like this:
if (touch_dev->touch_info.finger_cnt > MAX_SUPPORTED_FINGER_NUM)
touch_dev->touch_info.finger_cnt = MAX_SUPPORTED_FINGER_NUM;
As MAX_SUPPORTED_FINGER_NUM is an ordinal and the field is
a bitmask this seems quite confused.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220228233017.2270599-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73cca71a90 ]
As reported by the STEPCONFIG[1-16] registered field descriptions of the
TI reference manual, for the ADC "in single ended, SEL_INM_SWC_3_0 must
be 1xxx".
Unlike the Y and Z coordinates, this bit has not been set for the step
configuration registers used to sample the X coordinate.
Fixes: 1b8be32e69 ("Input: add support for TI Touchscreen controller")
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Link: https://lore.kernel.org/r/20211212125358.14416-2-dariobin@libero.it
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf73ed894e ]
Since irq request is the last thing in the driver probe, it happens
later than the input device registration. This means that there is a
small time window where if the open method is called the driver will
attempt to enable not yet available irq.
Fix that by moving the irq request before the input device registration.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Fixes: 26822652c8 ("Input: add zinitix touchscreen driver")
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220106072840.36851-2-nikita@trvn.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2667f6b7af ]
I have a ST1633 touch controller which fails to probe due to a timeout
waiting for the controller to become ready. Increasing the minimum
delay to 100ms ensures that the probe sequence completes successfully.
The ST1633 datasheet says nothing about the maximum delay here and the
ST1232 I2C protocol document says "wait until" with no notion of a
timeout.
Since this only runs once during probe, being generous with the timout
seems reasonable and most likely the device will become ready
eventually.
(It may be worth noting that I saw this issue with a PREEMPT_RT patched
kernel which probably has tighter wakeups from usleep_range() than other
preemption models.)
Fixes: f605be6a57 ("Input: st1232 - wait until device is ready before reading resolution")
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210929152609.2421483-1-john@metanate.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Pull input fixes from Dmitry Torokhov:
- a new product ID for the xpad joystick driver
- fixes to resistive-adc-touch and snvs_pwrkey drivers
- a change to touchscreen helpers to make clang happier
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: touchscreen - avoid bitwise vs logical OR warning
Input: xpad - add support for another USB ID of Nacon GC-100
Input: resistive-adc-touch - fix division by zero error on z1 == 0
Input: snvs_pwrkey - add clk handling
Pull input updates from Dmitry Torokhov:
- several device tree bindings for input devices have been converted to
yaml
- dropped no longer used ixp4xx-beeper and CSR Prima2 PWRC drivers
- analog joystick has been converted to use ktime API and no longer
warn about low resolution timers
- a few driver fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (24 commits)
Input: analog - always use ktime functions
Input: mms114 - support MMS134S
Input: elan_i2c - reduce the resume time for controller in Whitebox
Input: edt-ft5x06 - added case for EDT EP0110M09
Input: adc-keys - drop bogus __refdata annotation
Input: Fix spelling mistake in Kconfig "useable" -> "usable"
Input: Fix spelling mistake in Kconfig "Modul" -> "Module"
Input: remove dead CSR Prima2 PWRC driver
Input: adp5589-keys - use the right header
Input: adp5588-keys - use the right header
dt-bindings: input: tsc2005: Convert to YAML schema
Input: ep93xx_keypad - prepare clock before using it
dt-bindings: input: sun4i-lradc: Add wakeup-source
dt-bindings: input: Convert Regulator Haptic binding to a schema
dt-bindings: input: Convert Pixcir Touchscreen binding to a schema
dt-bindings: input: Convert ChipOne ICN8318 binding to a schema
Input: pm8941-pwrkey - fix comma vs semicolon issue
dt-bindings: power: reset: qcom-pon: Convert qcom PON binding to yaml
dt-bindings: input: pm8941-pwrkey: Convert pm8941 power key binding to yaml
dt-bindings: power: reset: Change 'additionalProperties' to true
...
Pull input updates from Dmitry Torokhov:
- a new driver for SparkFun Qwiic Joystick
- pm8941-pwrkey driver now supports PMK8350
- a bunch of assorted driver fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (44 commits)
Input: joydev - prevent use of not validated data in JSIOCSBTNMAP ioctl
Input: hideep - fix the uninitialized use in hideep_nvm_unlock()
Input: trackpoint - use kobj_to_dev()
Input: atkbd - use kobj_to_dev()
Input: tsc200x-core - use kobj_to_dev()
Input: ims-pcu - use kobj_to_dev()
Input: cros_ec_keyb - use kobj_to_dev() API
dt-bindings: input: touchscreen: st1232: Convert to json-schema
Input: i8042 - fix typos in comments
Input: add SparkFun Qwiic Joystick driver
dt-bindings: Add vendor prefix and bindings for Qwiic Joystick
Input: cy8ctmg110_ts - switch to using gpiod API
Input: cy8ctmg110_ts - switch to using managed resources
Input: cy8ctmg110_ts - use endian helpers when converting data on wire
Input: cy8ctmg110_ts - let I2C core configure wake interrupt
Input: cy8ctmg110_ts - do not hardcode as wakeup source
Input: cy8ctmg110_ts - do not hard code interrupt trigger
Input: cy8ctmg110_ts - rely on platform code to supply interrupt
Input: resistive-adc-touch - fix uninitialized variable 'press'
Input: pm8941-pwrkey - add support for PMK8350 PON_HLOS PMIC peripheral
...
Inside function hideep_nvm_unlock(), variable "unmask_code" could
be uninitialized if hideep_pgm_r_reg() returns error, however, it
is used in the later if statement after an "and" operation, which
is potentially unsafe.
Signed-off-by: Yizhuo <yzhai003@ucr.edu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In the case where st->ch_map[GRTS_CH_PRESSURE] < GRTS_MAX_CHANNELS is false
and also st->ch_map[GRTS_CH_Z1] < GRTS_MAX_CHANNELS is false the variable
press is not initialized and contains garbage. In this situation
st->pressure is also false, so we do not actually use press value, but
it is impossible for the compiler to realize this, and it emits
"uninitialized variable" warning. Fix this by initializing press
to 0 and allows us to also remove an else clause that sets press to 0.
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: 60b7db914d ("Input: resistive-adc-touch - rework mapping of channels")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210603220809.155118-1-colin.king@canonical.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
At the moment, the edt-ft5x06 driver can control a single regulator
("vcc"). However, some FocalTech touch controllers have an additional
IOVCC pin that should be supplied with the digital I/O voltage.
The I/O voltage might be provided by another regulator that should also
be kept on. Otherwise, the touchscreen can randomly stop functioning if
the regulator is turned off because no other components still require it.
Implement (optional) support for also enabling an "iovcc-supply".
The datasheet specifies a delay of ~ 10us before enabling VDD/VCC
after IOVCC is enabled, so make sure to enable IOVCC first.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210510193108.50178-2-stephan@gerhold.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
