[ Upstream commit 2593f7e0dc ]
Set ret = 0 on successful completion of the processing loop in
cs_dsp_load() and cs_dsp_load_coeff() to ensure that the function
returns 0 on success.
All normal firmware files will have at least one data block, and
processing this block will set ret == 0, from the result of either
regmap_raw_write() or cs_dsp_parse_coeff().
The kunit tests create a dummy firmware file that contains only the
header, without any data blocks. This gives cs_dsp a file to "load"
that will not cause any side-effects. As there aren't any data blocks,
the processing loop will not set ret == 0.
Originally there was a line after the processing loop:
ret = regmap_async_complete(regmap);
which would set ret == 0 before the function returned.
Commit fe08b7d508 ("firmware: cs_dsp: Remove async regmap writes")
changed the regmap write to a normal sync write, so the call to
regmap_async_complete() wasn't necessary and was removed. It was
overlooked that the ret here wasn't only to check the result of
regmap_async_complete(), it also set the final return value of the
function.
Fixes: fe08b7d508 ("firmware: cs_dsp: Remove async regmap writes")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20250323170529.197205-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cb16dfed00 upstream.
Ben reports spurious EFI zboot failures on a system where physical RAM
starts at 0x0. When doing random memory allocation from the EFI stub on
such a platform, a random seed of 0x0 (which means no entropy source is
available) will result in the allocation to be placed at address 0x0 if
sufficient space is available.
When this allocation is subsequently passed on to the decompression
code, the 0x0 address is mistaken for NULL and the code complains and
gives up.
So avoid address 0x0 when doing random allocation, and set the minimum
address to the minimum alignment.
Cc: <stable@vger.kernel.org>
Reported-by: Ben Schneider <ben@bens.haus>
Tested-by: Ben Schneider <ben@bens.haus>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fbf10b86f6 ]
imx_scu_probe() calls of_parse_phandle_with_args(), but does not
release the OF node reference obtained by it. Add a of_node_put() call
after done with the node.
Fixes: f25a066d1a ("firmware: imx-scu: Support one TX and one RX")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07e0d99a2f ]
When performing an iSCSI boot using IPv6, iscsistart still reads the
/sys/firmware/ibft/ethernetX/subnet-mask entry. Since the IPv6 prefix
length is 64, this causes the shift exponent to become negative,
triggering a UBSAN warning. As the concept of a subnet mask does not
apply to IPv6, the value is set to ~0 to suppress the warning message.
Signed-off-by: Chengen Du <chengen.du@canonical.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d55d5bc5d9 upstream.
The x86 decompressor is built and linked as a separate executable, but
it shares components with the kernel proper, which are either #include'd
as C files, or linked into the decompresor as a static library (e.g, the
EFI stub)
Both the kernel itself and the decompressor define a global symbol
'boot_params' to refer to the boot_params struct, but in the former
case, it refers to the struct directly, whereas in the decompressor, it
refers to a global pointer variable referring to the struct boot_params
passed by the bootloader or constructed from scratch.
This ambiguity is unfortunate, and makes it impossible to assign this
decompressor variable from the x86 EFI stub, given that declaring it as
extern results in a clash. So rename the decompressor version (whose
scope is limited) to boot_params_ptr.
[ mingo: Renamed 'boot_params_p' to 'boot_params_ptr' for clarity ]
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: linux-kernel@vger.kernel.org
[ardb: include references to boot_params in x86-stub.[ch]]
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b90e7ace7 upstream.
Currently, when validating the mokvar table, we (re)map the entire table
on each iteration of the loop, adding space as we discover new entries.
If the table grows over a certain size, this fails due to limitations of
early_memmap(), and we get a failure and traceback:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at mm/early_ioremap.c:139 __early_ioremap+0xef/0x220
...
Call Trace:
<TASK>
? __early_ioremap+0xef/0x220
? __warn.cold+0x93/0xfa
? __early_ioremap+0xef/0x220
? report_bug+0xff/0x140
? early_fixup_exception+0x5d/0xb0
? early_idt_handler_common+0x2f/0x3a
? __early_ioremap+0xef/0x220
? efi_mokvar_table_init+0xce/0x1d0
? setup_arch+0x864/0xc10
? start_kernel+0x6b/0xa10
? x86_64_start_reservations+0x24/0x30
? x86_64_start_kernel+0xed/0xf0
? common_startup_64+0x13e/0x141
</TASK>
---[ end trace 0000000000000000 ]---
mokvar: Failed to map EFI MOKvar config table pa=0x7c4c3000, size=265187.
Mapping the entire structure isn't actually necessary, as we don't ever
need more than one entry header mapped at once.
Changes efi_mokvar_table_init() to only map each entry header, not the
entire table, when determining the table size. Since we're not mapping
any data past the variable name, it also changes the code to enforce
that each variable name is NUL terminated, rather than attempting to
verify it in place.
Cc: <stable@vger.kernel.org>
Signed-off-by: Peter Jones <pjones@redhat.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fe08b7d508 ]
Change calls to async regmap write functions to use the normal
blocking writes so that the cs35l56 driver can use spi_bus_lock() to
gain exclusive access to the SPI bus.
As this is part of a fix, it makes only the minimal change to swap the
functions to the blocking equivalents. There's no need to risk
reworking the buffer allocation logic that is now partially redundant.
The async writes are a 12-year-old workaround for inefficiency of
synchronous writes in the SPI subsystem. The SPI subsystem has since
been changed to avoid the overheads, so this workaround should not be
necessary.
The cs35l56 driver needs to use spi_bus_lock() prevent bus activity
while it is soft-resetting the cs35l56. But spi_bus_lock() is
incompatible with spi_async() calls, which will fail with -EBUSY.
Fixes: 8a731fd37f ("ASoC: cs35l56: Move utility functions to shared file")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20250225131843.113752-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a744cceeb ]
Commit 2e4955167e ("firmware: qcom: scm: Fix __scm and waitq
completion variable initialization") introduced a write barrier in probe
function to store global '__scm' variable. It also claimed that it
added a read barrier, because as we all known barriers are paired (see
memory-barriers.txt: "Note that write barriers should normally be paired
with read or address-dependency barriers"), however it did not really
add it.
The offending commit used READ_ONCE() to access '__scm' global which is
not a barrier.
The barrier is needed so the store to '__scm' will be properly visible.
This is most likely not fatal in current driver design, because missing
read barrier would mean qcom_scm_is_available() callers will access old
value, NULL. Driver does not support unbinding and does not correctly
handle probe failures, thus there is no risk of stale or old pointer in
'__scm' variable.
However for code correctness, readability and to be sure that we did not
mess up something in this tricky topic of SMP barriers, add a read
barrier for accessing '__scm'. Change also comment from useless/obvious
what does barrier do, to what is expected: which other parts of the code
are involved here.
Fixes: 2e4955167e ("firmware: qcom: scm: Fix __scm and waitq completion variable initialization")
Cc: stable@vger.kernel.org
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241209-qcom-scm-missing-barriers-and-all-sort-of-srap-v2-1-9061013c8d92@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ba69e0750b upstream.
UEFI 2.11 introduced EFI_MEMORY_HOT_PLUGGABLE to annotate system memory
regions that are 'cold plugged' at boot, i.e., hot pluggable memory that
is available from early boot, and described as system RAM by the
firmware.
Existing loaders and EFI applications running in the boot context will
happily use this memory for allocating data structures that cannot be
freed or moved at runtime, and this prevents the memory from being
unplugged. Going forward, the new EFI_MEMORY_HOT_PLUGGABLE attribute
should be tested, and memory annotated as such should be avoided for
such allocations.
In the EFI stub, there are a couple of occurrences where, instead of the
high-level AllocatePages() UEFI boot service, a low-level code sequence
is used that traverses the EFI memory map and carves out the requested
number of pages from a free region. This is needed, e.g., for allocating
as low as possible, or for allocating pages at random.
While AllocatePages() should presumably avoid special purpose memory and
cold plugged regions, this manual approach needs to incorporate this
logic itself, in order to prevent the kernel itself from ending up in a
hot unpluggable region, preventing it from being unplugged.
So add the EFI_MEMORY_HOTPLUGGABLE macro definition, and check for it
where appropriate.
Cc: stable@vger.kernel.org
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ba14d9f49 upstream.
GCC 15 changed the default C standard version to C23, which should not
have impacted the kernel because it requests the gnu11 standard via
'-std=' in the main Makefile. However, the EFI libstub Makefile uses its
own set of KBUILD_CFLAGS for x86 without a '-std=' value (i.e., using
the default), resulting in errors from the kernel's definitions of bool,
true, and false in stddef.h, which are reserved keywords under C23.
./include/linux/stddef.h:11:9: error: expected identifier before ‘false’
11 | false = 0,
./include/linux/types.h:35:33: error: two or more data types in declaration specifiers
35 | typedef _Bool bool;
Set '-std=gnu11' in the x86 cflags to resolve the error and consistently
use the same C standard version for the entire kernel. All other
architectures reuse KBUILD_CFLAGS from the rest of the kernel, so this
issue is not visible for them.
Cc: stable@vger.kernel.org
Reported-by: Kostadin Shishmanov <kostadinshishmanov@protonmail.com>
Closes: https://lore.kernel.org/4OAhbllK7x4QJGpZjkYjtBYNLd_2whHx9oFiuZcGwtVR4hIzvduultkgfAIRZI3vQpZylu7Gl929HaYFRGeMEalWCpeMzCIIhLxxRhq4U-Y=@protonmail.com/
Reported-by: Jakub Jelinek <jakub@redhat.com>
Closes: https://lore.kernel.org/Z4467umXR2PZ0M1H@tucnak/
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 19fdc68aa7 ]
A build with W=1 fails because there are code and data that are not
needed or used when CONFIG_EFI is not set. Move the "#ifdef CONFIG_EFI"
block to earlier in the source file so that the unused code/data are
not built.
drivers/firmware/efi/sysfb_efi.c:345:39: warning: ‘efifb_fwnode_ops’ defined but not used [-Wunused-const-variable=]
345 | static const struct fwnode_operations efifb_fwnode_ops = {
| ^~~~~~~~~~~~~~~~
drivers/firmware/efi/sysfb_efi.c:238:35: warning: ‘efifb_dmi_swap_width_height’ defined but not used [-Wunused-const-variable=]
238 | static const struct dmi_system_id efifb_dmi_swap_width_height[] __initconst = {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/firmware/efi/sysfb_efi.c:188:35: warning: ‘efifb_dmi_system_table’ defined but not used [-Wunused-const-variable=]
188 | static const struct dmi_system_id efifb_dmi_system_table[] __initconst = {
| ^~~~~~~~~~~~~~~~~~~~~~
Fixes: 15d27b15de ("efi: sysfb_efi: fix build when EFI is not set")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202501071933.20nlmJJt-lkp@intel.com/
Cc: David Rheinsberg <david@readahead.eu>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Simona Vetter <simona@ffwll.ch>
Cc: linux-fbdev@vger.kernel.org
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: linux-efi@vger.kernel.org
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 06d39d79cb upstream.
cmdline_ptr is an out parameter, which is not allocated by the function
itself, and likely points into the caller's stack.
cmdline refers to the pool allocation that should be freed when cleaning
up after a failure, so pass this instead to free_pool().
Fixes: 42c8ea3dca ("efi: libstub: Factor out EFI stub entrypoint ...")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e6d654e9f5 ]
A prior bugfix that fixes a signed/unsigned error causes
another signed unsigned error.
A situation where log_tbl->size is invalid can cause the
size passed to memblock_reserve to become negative.
log_size from the main event log is an unsigned int, and
the code reduces to the following
u64 value = (int)unsigned_value;
This results in sign extension, and the value sent to
memblock_reserve becomes effectively negative.
Fixes: be59d57f98 ("efi/tpm: Fix sanity check of unsigned tbl_size being less than zero")
Signed-off-by: Gregory Price <gourry@gourry.net>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aacfa0ef24 ]
efi_convert_cmdline() always returns a size of at least 1 because it
counts the NUL terminator, so the "cmdline_size == 0" condition is never
satisfied.
Change it to check if the string starts with a NUL character to get the
intended behavior: to use CONFIG_CMDLINE when load_options_size == 0.
Fixes: 60f38de7a8 ("efi/libstub: Unify command line param parsing")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0a18e91eb ]
The clear channel transport operation is supposed to be called exclusively
on the P2A channel from the agent, since it relinquishes the ownership of
the channel to the platform, after this latter has initiated some sort of
P2A communication.
Make sure that, if it is ever called on a A2P, is logged and ignored.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Message-Id: <20241021171544.2579551-1-cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8c462d5648 upstream.
SMCCCv1.3 added a hint bit which callers can set in an SMCCC function ID
(AKA "FID") to indicate that it is acceptable for the SMCCC
implementation to discard SVE and/or SME state over a specific SMCCC
call. The kernel support for using this hint is broken and SMCCC calls
may clobber the SVE and/or SME state of arbitrary tasks, though FPSIMD
state is unaffected.
The kernel support is intended to use the hint when there is no SVE or
SME state to save, and to do this it checks whether TIF_FOREIGN_FPSTATE
is set or TIF_SVE is clear in assembly code:
| ldr <flags>, [<current_task>, #TSK_TI_FLAGS]
| tbnz <flags>, #TIF_FOREIGN_FPSTATE, 1f // Any live FP state?
| tbnz <flags>, #TIF_SVE, 2f // Does that state include SVE?
|
| 1: orr <fid>, <fid>, ARM_SMCCC_1_3_SVE_HINT
| 2:
| << SMCCC call using FID >>
This is not safe as-is:
(1) SMCCC calls can be made in a preemptible context and preemption can
result in TIF_FOREIGN_FPSTATE being set or cleared at arbitrary
points in time. Thus checking for TIF_FOREIGN_FPSTATE provides no
guarantee.
(2) TIF_FOREIGN_FPSTATE only indicates that the live FP/SVE/SME state in
the CPU does not belong to the current task, and does not indicate
that clobbering this state is acceptable.
When the live CPU state is clobbered it is necessary to update
fpsimd_last_state.st to ensure that a subsequent context switch will
reload FP/SVE/SME state from memory rather than consuming the
clobbered state. This and the SMCCC call itself must happen in a
critical section with preemption disabled to avoid races.
(3) Live SVE/SME state can exist with TIF_SVE clear (e.g. with only
TIF_SME set), and checking TIF_SVE alone is insufficient.
Remove the broken support for the SMCCCv1.3 SVE saving hint. This is
effectively a revert of commits:
* cfa7ff959a ("arm64: smccc: Support SMCCC v1.3 SVE register saving hint")
* a7c3acca53 ("arm64: smccc: Save lr before calling __arm_smccc_sve_check()")
... leaving behind the ARM_SMCCC_VERSION_1_3 and ARM_SMCCC_1_3_SVE_HINT
definitions, since these are simply definitions from the SMCCC
specification, and the latter is used in KVM via ARM_SMCCC_CALL_HINTS.
If we want to bring this back in future, we'll probably want to handle
this logic in C where we can use all the usual FPSIMD/SVE/SME helper
functions, and that'll likely require some rework of the SMCCC code
and/or its callers.
Fixes: cfa7ff959a ("arm64: smccc: Support SMCCC v1.3 SVE register saving hint")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Will Deacon <will@kernel.org>
Cc: stable@vger.kernel.org
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20241106160448.2712997-1-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit da1642bc97 ]
send_message() does not block in the MBOX implementation. This is
because the mailbox layer has its own queue. However, this confuses
the per xfer timeouts as they all start their timeout ticks in
parallel.
Consider a case where the xfer timeout is 30ms and a SCMI transaction
takes 25ms:
| 0ms: Message #0 is queued in mailbox layer and sent out, then sits
| at scmi_wait_for_message_response() with a timeout of 30ms
| 1ms: Message #1 is queued in mailbox layer but not sent out yet.
| Since send_message() doesn't block, it also sits at
| scmi_wait_for_message_response() with a timeout of 30ms
| ...
| 25ms: Message #0 is completed, txdone is called and message #1 is sent
| 31ms: Message #1 times out since the count started at 1ms. Even though
| it has only been inflight for 6ms.
Fixes: 5c8a47a5a9 ("firmware: arm_scmi: Make scmi core independent of the transport type")
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Message-Id: <20241014160717.1678953-1-justin.chen@broadcom.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c5a1627f4 ]
Commit 50e782a86c ("efi/unaccepted: Fix soft lockups caused by
parallel memory acceptance") has released the spinlock so other CPUs can
do memory acceptance in parallel and not triggers softlockup on other
CPUs.
However the softlock up was intermittent shown up if the memory of the
TD guest is large, and the timeout of softlockup is set to 1 second:
RIP: 0010:_raw_spin_unlock_irqrestore
Call Trace:
? __hrtimer_run_queues
<IRQ>
? hrtimer_interrupt
? watchdog_timer_fn
? __sysvec_apic_timer_interrupt
? __pfx_watchdog_timer_fn
? sysvec_apic_timer_interrupt
</IRQ>
? __hrtimer_run_queues
<TASK>
? hrtimer_interrupt
? asm_sysvec_apic_timer_interrupt
? _raw_spin_unlock_irqrestore
? __sysvec_apic_timer_interrupt
? sysvec_apic_timer_interrupt
accept_memory
try_to_accept_memory
do_huge_pmd_anonymous_page
get_page_from_freelist
__handle_mm_fault
__alloc_pages
__folio_alloc
? __tdx_hypercall
handle_mm_fault
vma_alloc_folio
do_user_addr_fault
do_huge_pmd_anonymous_page
exc_page_fault
? __do_huge_pmd_anonymous_page
asm_exc_page_fault
__handle_mm_fault
When the local irq is enabled at the end of accept_memory(), the
softlockup detects that the watchdog on single CPU has not been fed for
a while. That is to say, even other CPUs will not be blocked by
spinlock, the current CPU might be stunk with local irq disabled for a
while, which hurts not only nmi watchdog but also softlockup.
Chao Gao pointed out that the memory accept could be time costly and
there was similar report before. Thus to avoid any softlocup detection
during this stage, give the softlockup a flag to skip the timeout check
at the end of accept_memory(), by invoking touch_softlockup_watchdog().
Reported-by: Md Iqbal Hossain <md.iqbal.hossain@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Fixes: 50e782a86c ("efi/unaccepted: Fix soft lockups caused by parallel memory acceptance")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
(cherry picked from commit 1c5a1627f4)
[Harshit: CVE-2024-36936; Minor conflict resolution due to header file
differences due to missing commit: 7cd34dd3c9 ("efi/unaccepted: do not
let /proc/vmcore try to access unaccepted memory") in 6.6.y]
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77d48d39e9 upstream.
The TPM event log table is a Linux specific construct, where the data
produced by the GetEventLog() boot service is cached in memory, and
passed on to the OS using an EFI configuration table.
The use of EFI_LOADER_DATA here results in the region being left
unreserved in the E820 memory map constructed by the EFI stub, and this
is the memory description that is passed on to the incoming kernel by
kexec, which is therefore unaware that the region should be reserved.
Even though the utility of the TPM2 event log after a kexec is
questionable, any corruption might send the parsing code off into the
weeds and crash the kernel. So let's use EFI_ACPI_RECLAIM_MEMORY
instead, which is always treated as reserved by the E820 conversion
logic.
Cc: <stable@vger.kernel.org>
Reported-by: Breno Leitao <leitao@debian.org>
Tested-by: Usama Arif <usamaarif642@gmail.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 62412a9357 ]
Add a check to cs_dsp_coeff_write_ctrl() to abort if the control
is not writeable.
The cs_dsp code originated as an ASoC driver (wm_adsp) where all
controls were exported as ALSA controls. It relied on ALSA to
enforce the read-only permission. Now that the code has been
separated from ALSA/ASoC it must perform its own permission check.
This isn't currently causing any problems so there shouldn't be any
need to backport this. If the client of cs_dsp exposes the control as
an ALSA control, it should set permissions on that ALSA control to
protect it. The few uses of cs_dsp_coeff_write_ctrl() inside drivers
are for writable controls.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20240702110809.16836-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9960085a3a upstream.
Currently get_wq_ctx() is wrongly configured as a standard call. When two
SMC calls are in sleep and one SMC wakes up, it calls get_wq_ctx() to
resume the corresponding sleeping thread. But if get_wq_ctx() is
interrupted, goes to sleep and another SMC call is waiting to be allocated
a waitq context, it leads to a deadlock.
To avoid this get_wq_ctx() must be an atomic call and can't be a standard
SMC call. Hence mark get_wq_ctx() as a fast call.
Fixes: 6bf3259922 ("firmware: qcom: scm: Add wait-queue handling logic")
Cc: stable@vger.kernel.org
Signed-off-by: Murali Nalajala <quic_mnalajal@quicinc.com>
Signed-off-by: Unnathi Chalicheemala <quic_uchalich@quicinc.com>
Reviewed-by: Elliot Berman <quic_eberman@quicinc.com>
Link: https://lore.kernel.org/r/20240814223244.40081-1-quic_uchalich@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 78aa89d1df ]
On ARM PCI systems, the PCI hierarchy might be reconfigured during
boot and the firmware framebuffer might move as a result of that.
The values in screen_info will then be invalid.
Work around this problem by tracking the framebuffer's initial
location before it get relocated; then fix the screen_info state
between reloaction and creating the firmware framebuffer's device.
This functionality has been lifted from efifb. See the commit message
of commit 55d728a40d ("efi/fb: Avoid reconfiguration of BAR that
covers the framebuffer") for more information.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240212090736.11464-8-tzimmermann@suse.de
Stable-dep-of: c2bc958b2b ("fbdev: vesafb: Detect VGA compatibility from screen info's VESA attributes")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75fa9b7e37 ]
The plain values as stored in struct screen_info need to be decoded
before being used. Add helpers that decode the type of video output
and the framebuffer I/O aperture.
Old or non-x86 systems may not set the type of video directly, but
only indicate the presence by storing 0x01 in orig_video_isVGA. The
decoding logic in screen_info_video_type() takes this into account.
It then follows similar code in vgacon's vgacon_startup() to detect
the video type from the given values.
A call to screen_info_resources() returns all known resources of the
given screen_info. The resources' values have been taken from existing
code in vgacon and vga16fb. These drivers can later be converted to
use the new interfaces.
v2:
* return ssize_t from screen_info_resources()
* don't call __screen_info_has_lfb() unnecessarily
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240212090736.11464-2-tzimmermann@suse.de
Stable-dep-of: c2bc958b2b ("fbdev: vesafb: Detect VGA compatibility from screen info's VESA attributes")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ee8b8f5d83 upstream.
After calling uefi interface allocate_pool to apply for memory, we
should clear 0 to prevent the possibility of using random values.
Signed-off-by: Qiang Ma <maqianga@uniontech.com>
Cc: <stable@vger.kernel.org> # v6.6+
Fixes: 732ea9db9d ("efi: libstub: Move screen_info handling to common code")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae835a96d7 upstream.
This is a partial revert of commit
8117961d98 ("x86/efi: Disregard setup header of loaded image")
which triggers boot issues on older Dell laptops. As it turns out,
switching back to a heap allocation for the struct boot_params
constructed by the EFI stub works around this, even though it is unclear
why.
Cc: Christian Heusel <christian@heusel.eu>
Reported-by: <mavrix#kernel@simplelogin.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb318ca0a5 upstream.
The fail label is only used in a situation where the previous EFI API
call succeeded, and so status will be set to EFI_SUCCESS. Fix this, by
dropping the goto entirely, and call efi_exit() with the correct error
code.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 49e24c80d3 ]
Initialize the completion before the mailbox channel is requested.
Fixes: 389711b374 ("firmware: Add Turris Mox rWTM firmware driver")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8467cfe821 ]
The wait_for_completion_timeout() function returns 0 if timed out, and a
positive value if completed. Fix the usage of this function.
Fixes: 389711b374 ("firmware: Add Turris Mox rWTM firmware driver")
Fixes: 2eab59cf0d ("firmware: turris-mox-rwtm: fail probing when firmware does not support hwrng")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0bafb172b1 ]
Do not complete the "command done" completion if there are no waiters.
This can happen if a wait_for_completion() timed out or was interrupted.
Fixes: 389711b374 ("firmware: Add Turris Mox rWTM firmware driver")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5134acb15d ]
When building ARCH=loongarch defconfig + CONFIG_UNWINDER_ORC=y using
LLVM, there is a warning from ld.lld when linking the EFI zboot image
due to the use of unreachable() in number() in vsprintf.c:
ld.lld: warning: drivers/firmware/efi/libstub/lib.a(vsprintf.stub.o):(.discard.unreachable+0x0): has non-ABS relocation R_LARCH_32_PCREL against symbol ''
If the compiler cannot eliminate the default case for any reason, the
.discard.unreachable section will remain in the final binary but the
entire point of any section prefixed with .discard is that it is only
used at compile time, so it can be discarded via /DISCARD/ in a linker
script. The asm-generic vmlinux.lds.h includes .discard and .discard.*
in the COMMON_DISCARDS macro but that is not used for zboot.lds, as it
is not a kernel image linker script.
Add .discard and .discard.* to /DISCARD/ in zboot.lds, so that any
sections meant to be discarded at link time are not included in the
final zboot image. This issue is not specific to LoongArch, it is just
the first architecture to select CONFIG_OBJTOOL, which defines
annotate_unreachable() as an asm statement to add the
.discard.unreachable section, and use the EFI stub.
Closes: https://github.com/ClangBuiltLinux/linux/issues/2023
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 680e126ec0 ]
Use strnlen() instead of strlen() on the algorithm and coefficient name
string arrays in V1 wmfw files.
In V1 wmfw files the name is a NUL-terminated string in a fixed-size
array. cs_dsp should protect against overrunning the array if the NUL
terminator is missing.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: f6bc909e76 ("firmware: cs_dsp: add driver to support firmware loading on Cirrus Logic DSPs")
Link: https://patch.msgid.link/20240708144855.385332-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2163aff6be ]
Check that all fields of a V2 algorithm header fit into the available
firmware data buffer.
The wmfw V2 format introduced variable-length strings in the algorithm
block header. This means the overall header length is variable, and the
position of most fields varies depending on the length of the string
fields. Each field must be checked to ensure that it does not overflow
the firmware data buffer.
As this ia bugfix patch, the fixes avoid making any significant change to
the existing code. This makes it easier to review and less likely to
introduce new bugs.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: f6bc909e76 ("firmware: cs_dsp: add driver to support firmware loading on Cirrus Logic DSPs")
Link: https://patch.msgid.link/20240627141432.93056-5-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6598afa932 ]
Move the payload length check in cs_dsp_load() and cs_dsp_coeff_load()
to be done before the block is processed.
The check that the length of a block payload does not exceed the number
of remaining bytes in the firwmware file buffer was being done near the
end of the loop iteration. However, some code before that check used the
length field without validating it.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: f6bc909e76 ("firmware: cs_dsp: add driver to support firmware loading on Cirrus Logic DSPs")
Link: https://patch.msgid.link/20240627141432.93056-4-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 959fe01e85 ]
Return an error from cs_dsp_power_up() if a block header is longer
than the amount of data left in the file.
The previous code in cs_dsp_load() and cs_dsp_load_coeff() would loop
while there was enough data left in the file for a valid region. This
protected against overrunning the end of the file data, but it didn't
abort the file processing with an error.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: f6bc909e76 ("firmware: cs_dsp: add driver to support firmware loading on Cirrus Logic DSPs")
Link: https://patch.msgid.link/20240627141432.93056-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3019b86bce ]
Fix the checking that firmware file buffer is large enough for the
wmfw header, to prevent overrunning the buffer.
The original code tested that the firmware data buffer contained
enough bytes for the sums of the size of the structs
wmfw_header + wmfw_adsp1_sizes + wmfw_footer
But wmfw_adsp1_sizes is only used on ADSP1 firmware. For ADSP2 and
Halo Core the equivalent struct is wmfw_adsp2_sizes, which is
4 bytes longer. So the length check didn't guarantee that there
are enough bytes in the firmware buffer for a header with
wmfw_adsp2_sizes.
This patch splits the length check into three separate parts. Each
of the wmfw_header, wmfw_adsp?_sizes and wmfw_footer are checked
separately before they are used.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: f6bc909e76 ("firmware: cs_dsp: add driver to support firmware loading on Cirrus Logic DSPs")
Link: https://patch.msgid.link/20240627141432.93056-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit beb2800074 ]
Currently kernel entry in head.S is in DMW address range, firmware is
instructed to jump to this address after loading the kernel image.
However kernel should not make any assumption on firmware's DMW
setting, thus the entry point should be a physical address falls into
direct translation region.
Fix by converting entry address to physical and amend entry calculation
logic in libstub accordingly.
BTW, use ABSOLUTE() to calculate variables to make Clang/LLVM happy.
Cc: stable@vger.kernel.org
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 174a0c565c ]
The use of the 'kernel_offset' variable to position the image file that
has been loaded by UEFI or GRUB is unnecessary, because we can directly
position the loaded image file through using the image_base field of the
efi_loaded_image struct provided by UEFI.
Replace kernel_offset with image_base to position the image file that has
been loaded by UEFI or GRUB.
Signed-off-by: Wang Yao <wangyao@lemote.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Stable-dep-of: beb2800074 ("LoongArch: Fix entry point in kernel image header")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 75dde792d6 upstream.
The logic in __efi_memmap_init() is shared between two different
execution flows:
- mapping the EFI memory map early or late into the kernel VA space, so
that its entries can be accessed;
- the x86 specific cloning of the EFI memory map in order to insert new
entries that are created as a result of making a memory reservation
via a call to efi_mem_reserve().
In the former case, the underlying memory containing the kernel's view
of the EFI memory map (which may be heavily modified by the kernel
itself on x86) is not modified at all, and the only thing that changes
is the virtual mapping of this memory, which is different between early
and late boot.
In the latter case, an entirely new allocation is created that carries a
new, updated version of the kernel's view of the EFI memory map. When
installing this new version, the old version will no longer be
referenced, and if the memory was allocated by the kernel, it will leak
unless it gets freed.
The logic that implements this freeing currently lives on the code path
that is shared between these two use cases, but it should only apply to
the latter. So move it to the correct spot.
While at it, drop the dummy definition for non-x86 architectures, as
that is no longer needed.
Cc: <stable@vger.kernel.org>
Fixes: f0ef652347 ("efi: Fix efi_memmap_alloc() leaks")
Tested-by: Ashish Kalra <Ashish.Kalra@amd.com>
Link: https://lore.kernel.org/all/36ad5079-4326-45ed-85f6-928ff76483d3@amd.com
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e7c3696d46 ]
Currently we return the value from invoke_psci_fn() directly as return
value from psci_system_suspend(). It is wrong to send the PSCI interface
return value directly. psci_to_linux_errno() provide the mapping from
PSCI return value to the one that can be returned to the callers within
the kernel.
Use psci_to_linux_errno() to convert and return the correct value from
psci_system_suspend().
Fixes: faf7ec4a92 ("drivers: firmware: psci: add system suspend support")
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20240515095528.1949992-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c50b7fcf2 ]
There are several functions which are calling qcom_scm_bw_enable()
then returns immediately if the call fails and leaves the clocks
enabled.
Change the code of these functions to disable clocks when the
qcom_scm_bw_enable() call fails. This also fixes a possible dma
buffer leak in the qcom_scm_pas_init_image() function.
Compile tested only due to lack of hardware with interconnect
support.
Cc: stable@vger.kernel.org
Fixes: 65b7ebda50 ("firmware: qcom_scm: Add bw voting support to the SCM interface")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Link: https://lore.kernel.org/r/20240304-qcom-scm-disable-clk-v1-1-b36e51577ca1@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
