[ Upstream commit 574f5ee2c8 ]
Each bridge instance creates up to four auxiliary devices with different
names. However, their IDs are always zero, causing duplicate filename
errors when a system has multiple bridges:
sysfs: cannot create duplicate filename '/bus/auxiliary/devices/ti_sn65dsi86.gpio.0'
Fix this by using a unique instance ID per bridge instance. The
instance ID is derived from the I2C adapter number and the bridge's I2C
address, to support multiple instances on the same bus.
Fixes: bf73537f41 ("drm/bridge: ti-sn65dsi86: Break GPIO and MIPI-to-eDP bridge into sub-drivers")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/7a68a0e3f927e26edca6040067fb653eb06efb79.1733840089.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 902806baf3 ]
AUDIO_UPDATE bit (Bit 5 of MAIN register 0x4A) needs to be set to 1
while updating Audio InfoFrame information and then set to 0 when done.
Otherwise partially updated Audio InfoFrames could be sent out. Two
cases where this rule were not followed are fixed:
- In adv7511_hdmi_hw_params() make sure AUDIO_UPDATE bit is updated
before/after setting ADV7511_REG_AUDIO_INFOFRAME.
- In audio_startup() use the correct register for clearing
AUDIO_UPDATE bit.
The problem with corrupted audio infoframes were discovered by letting
a HDMI logic analyser check the output of ADV7535.
Note that this patchs replaces writing REG_GC(1) with
REG_INFOFRAME_UPDATE. Bit 5 of REG_GC(1) is positioned within field
GC_PP[3:0] and that field doesn't control audio infoframe and is read-
only. My conclusion therefore was that the author if this code meant to
clear bit 5 of REG_INFOFRAME_UPDATE from the very beginning.
Tested-by: Biju Das <biju.das.jz@bp.renesas.com>
Fixes: 53c515befe ("drm/bridge: adv7511: Add Audio support")
Signed-off-by: Stefan Ekenberg <stefan.ekenberg@axis.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241119-adv7511-audio-info-frame-v4-1-4ae68e76c89c@axis.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5f3f21728 ]
The IT6505 bridge chip has a active low reset line. Since it is a
"reset" and not an "enable" line, the GPIO should be asserted to
put it in reset and deasserted to bring it out of reset during
the power on sequence.
The polarity was inverted when the driver was first introduced, likely
because the device family that was targeted had an inverting level
shifter on the reset line.
The MT8186 Corsola devices already have the IT6505 in their device tree,
but the whole display pipeline is actually disabled and won't be enabled
until some remaining issues are sorted out. The other known user is
the MT8183 Kukui / Jacuzzi family; their device trees currently do not
have the IT6505 included.
Fix the polarity in the driver while there are no actual users.
Fixes: b5c84a9edc ("drm/bridge: add it6505 driver")
Cc: stable@vger.kernel.org
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241029095411.657616-1-wenst@chromium.org
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d343723c7 ]
When a display controller driver uses DRM_BRIDGE_ATTACH_NO_CONNECTOR,
tc358767 will behave properly and skip the creation of the connector.
However, tc_get_display_props(), which is used to find out about the DP
monitor and link, is only called from two places: .atomic_enable() and
tc_connector_get_modes(). The latter is only used when tc358767 creates
its own connector, i.e. when DRM_BRIDGE_ATTACH_NO_CONNECTOR is _not_
set.
Thus, the driver never finds out the link properties before get_edid()
is called. With num_lanes of 0 and link_rate of 0 there are not many
valid modes...
Fix this by adding tc_get_display_props() call at the beginning of
get_edid(), so that we have up to date information before looking at the
modes.
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Closes: https://lore.kernel.org/all/24282420-b4dd-45b3-bb1c-fc37fe4a8205@siemens.com/
Fixes: de5e6c027a ("drm/bridge: tc358767: add drm_panel_bridge support")
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231108-tc358767-v2-2-25c5f70a2159@ideasonboard.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe828fbd87 ]
If the bridge is attached with the DRM_BRIDGE_ATTACH_NO_CONNECTOR flag set,
this driver won't initialize a connector and hence display mode won't be
validated in drm_connector_helper_funcs::mode_valid(). So, move the mode
validation from drm_connector_helper_funcs::mode_valid() to
drm_bridge_funcs::mode_valid(), because the mode validation is always done
for the bridge.
Fixes: 30e2ae943c ("drm/bridge: Introduce LT8912B DSI to HDMI bridge")
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240813091637.1054586-1-victor.liu@nxp.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fc75c40fa ]
The DSI horizontal timing calculations done by the driver seem to often
lead to underflows or overflows, depending on the videomode.
There are two main things the current driver doesn't seem to get right:
DSI HSW and HFP, and VSDly. However, even following Toshiba's
documentation it seems we don't always get a working display.
This patch attempts to fix the horizontal timings for DSI event mode, and
on a system with a DSI->HDMI encoder, a lot of standard HDMI modes now
seem to work. The work relies on Toshiba's documentation, but also quite
a bit on empirical testing.
This also adds timing related debug prints to make it easier to improve
on this later.
The DSI pulse mode has only been tested with a fixed-resolution panel,
which limits the testing of different modes on DSI pulse mode. However,
as the VSDly calculation also affects pulse mode, so this might cause a
regression.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-12-31725f008a50@ideasonboard.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 484436ec5c ]
When the system power resumes, the TTL input of IT6505 may experience
some noise before the video signal stabilizes, necessitating a video
reset. This patch is implemented to prevent a loop of video error
interrupts, which can occur when a video reset in the video FIFO error
interrupt triggers another such interrupt. The patch processes the SCDT
and FIFO error interrupts simultaneously and ignores any video FIFO
error interrupts caused by a video reset.
Fixes: b5c84a9edc ("drm/bridge: add it6505 driver")
Signed-off-by: Kuro Chung <kuro.chung@ite.com.tw>
Signed-off-by: Hermes Wu <hermes.wu@ite.com.tw>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240522065528.1053439-1-kuro.chung@ite.com.tw
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce62600c4d ]
Device managed panel bridge wrappers are created by calling to
drm_panel_bridge_add_typed() and registering a release handler for
clean-up when the device gets unbound.
Since the memory for this bridge is also managed and linked to the panel
device, the release function should not try to free that memory.
Moreover, the call to devm_kfree() inside drm_panel_bridge_remove() will
fail in this case and emit a warning because the panel bridge resource
is no longer on the device resources list (it has been removed from
there before the call to release handlers).
Fixes: 67022227ff ("drm/bridge: Add a devm_ allocator for panel bridge.")
Signed-off-by: Adam Miotk <adam.miotk@arm.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610102739.139852-1-adam.miotk@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad81feb5b6 ]
This reverts commit 8a91b29f1f.
The regulator_disable() added by the original commit solves one kind of
regulator imbalance but adds another one as it allows the regulator to be
disabled one more time than it is enabled in the following scenario:
1. Start video pipeline -> sn65dsi83_atomic_pre_enable -> regulator_enable
2. PLL lock fails -> regulator_disable
3. Stop video pipeline -> sn65dsi83_atomic_disable -> regulator_disable
The reason is clear from the code flow, which looks like this (after
removing unrelated code):
static void sn65dsi83_atomic_pre_enable()
{
regulator_enable(ctx->vcc);
if (PLL failed locking) {
regulator_disable(ctx->vcc); <---- added by patch being reverted
return;
}
}
static void sn65dsi83_atomic_disable()
{
regulator_disable(ctx->vcc);
}
The use case for introducing the additional regulator_disable() was
removing the module for debugging (see link below for the discussion). If
the module is removed after a .atomic_pre_enable, i.e. with an active
pipeline from the DRM point of view, .atomic_disable is not called and thus
the regulator would not be disabled.
According to the discussion however there is no actual use case for
removing the module with an active pipeline, except for
debugging/development.
On the other hand, the occurrence of a PLL lock failure is possible due to
any physical reason (e.g. a temporary hardware failure for electrical
reasons) so handling it gracefully should be supported. As there is no way
for .atomic[_pre]_enable to report an error to the core, the only clean way
to support it is calling regulator_disabled() only in .atomic_disable,
unconditionally, as it was before.
Link: https://lore.kernel.org/all/15244220.uLZWGnKmhe@steina-w/
Fixes: 8a91b29f1f ("drm/bridge: ti-sn65dsi83: Fix enable error path")
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240426122259.46808-1-luca.ceresoli@bootlin.com
(cherry picked from commit 2940ee03b2)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30ea09a182 ]
The bridge always uses 24bpp internally. Therefore, for jeida-18
mapping we need to discard the lowest two bits for each channel and thus
starting with LV_[RGB]2. jeida-24 has the same mapping but uses four
lanes instead of three, with the forth pair transmitting the lowest two
bits of each channel. Thus, the mapping between jeida-18 and jeida-24
is actually the same, except that one channel is turned off (by
selecting the RGB666 format in VPCTRL).
While at it, remove the bogus comment about the hardware default because
the default is overwritten in any case.
Tested with a jeida-18 display (Evervision VGG644804).
Fixes: b26975593b ("display/drm/bridge: TC358775 DSI/LVDS driver")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240225062008.33191-5-tony@atomide.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 935a92a1c4 ]
In cdns_mhdp_atomic_enable(), the return value of drm_mode_duplicate() is
assigned to mhdp_state->current_mode, and there is a dereference of it in
drm_mode_set_name(), which will lead to a NULL pointer dereference on
failure of drm_mode_duplicate().
Fix this bug add a check of mhdp_state->current_mode.
Fixes: fb43aa0acd ("drm: bridge: Add support for Cadence MHDP8546 DPI/DP bridge")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240408125810.21899-1-amishin@t-argos.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff3d5d04db ]
The FORCE_STOP_STATE bit is unsuitable to force the DSI link into LP-11
mode. It seems the bridge internally queues DSI packets and when the
FORCE_STOP_STATE bit is cleared, they are sent in close succession
without any useful timing (this also means that the DSI lanes won't go
into LP-11 mode). The length of this gibberish varies between 1ms and
5ms. This sometimes breaks an attached bridge (TI SN65DSI84 in this
case). In our case, the bridge will fail in about 1 per 500 reboots.
The FORCE_STOP_STATE handling was introduced to have the DSI lanes in
LP-11 state during the .pre_enable phase. But as it turns out, none of
this is needed at all. Between samsung_dsim_init() and
samsung_dsim_set_display_enable() the lanes are already in LP-11 mode.
The code as it was before commit 20c827683d ("drm: bridge:
samsung-dsim: Fix init during host transfer") and 0c14d31306 ("drm:
bridge: samsung-dsim: Fix i.MX8M enable flow to meet spec") was correct
in this regard.
This patch basically reverts both commits. It was tested on an i.MX8M
SoC with an SN65DSI84 bridge. The signals were probed and the DSI
packets were decoded during initialization and link start-up. After this
patch the first DSI packet on the link is a VSYNC packet and the timing
is correct.
Command mode between .pre_enable and .enable was also briefly tested by
a quick hack. There was no DSI link partner which would have responded,
but it was made sure the DSI packet was send on the link. As a side
note, the command mode seems to just work in HS mode. I couldn't find
that the bridge will handle commands in LP mode.
Fixes: 20c827683d ("drm: bridge: samsung-dsim: Fix init during host transfer")
Fixes: 0c14d31306 ("drm: bridge: samsung-dsim: Fix i.MX8M enable flow to meet spec")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231113164344.1612602-1-mwalle@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08ac6f132d ]
A null pointer dereference crash has been observed rarely on TI
platforms using sii9022 bridge:
[ 53.271356] sii902x_get_edid+0x34/0x70 [sii902x]
[ 53.276066] sii902x_bridge_get_edid+0x14/0x20 [sii902x]
[ 53.281381] drm_bridge_get_edid+0x20/0x34 [drm]
[ 53.286305] drm_bridge_connector_get_modes+0x8c/0xcc [drm_kms_helper]
[ 53.292955] drm_helper_probe_single_connector_modes+0x190/0x538 [drm_kms_helper]
[ 53.300510] drm_client_modeset_probe+0x1f0/0xbd4 [drm]
[ 53.305958] __drm_fb_helper_initial_config_and_unlock+0x50/0x510 [drm_kms_helper]
[ 53.313611] drm_fb_helper_initial_config+0x48/0x58 [drm_kms_helper]
[ 53.320039] drm_fbdev_dma_client_hotplug+0x84/0xd4 [drm_dma_helper]
[ 53.326401] drm_client_register+0x5c/0xa0 [drm]
[ 53.331216] drm_fbdev_dma_setup+0xc8/0x13c [drm_dma_helper]
[ 53.336881] tidss_probe+0x128/0x264 [tidss]
[ 53.341174] platform_probe+0x68/0xc4
[ 53.344841] really_probe+0x188/0x3c4
[ 53.348501] __driver_probe_device+0x7c/0x16c
[ 53.352854] driver_probe_device+0x3c/0x10c
[ 53.357033] __device_attach_driver+0xbc/0x158
[ 53.361472] bus_for_each_drv+0x88/0xe8
[ 53.365303] __device_attach+0xa0/0x1b4
[ 53.369135] device_initial_probe+0x14/0x20
[ 53.373314] bus_probe_device+0xb0/0xb4
[ 53.377145] deferred_probe_work_func+0xcc/0x124
[ 53.381757] process_one_work+0x1f0/0x518
[ 53.385770] worker_thread+0x1e8/0x3dc
[ 53.389519] kthread+0x11c/0x120
[ 53.392750] ret_from_fork+0x10/0x20
The issue here is as follows:
- tidss probes, but is deferred as sii902x is still missing.
- sii902x starts probing and enters sii902x_init().
- sii902x calls drm_bridge_add(). Now the sii902x bridge is ready from
DRM's perspective.
- sii902x calls sii902x_audio_codec_init() and
platform_device_register_data()
- The registration of the audio platform device causes probing of the
deferred devices.
- tidss probes, which eventually causes sii902x_bridge_get_edid() to be
called.
- sii902x_bridge_get_edid() tries to use the i2c to read the edid.
However, the sii902x driver has not set up the i2c part yet, leading
to the crash.
Fix this by moving the drm_bridge_add() to the end of the
sii902x_init(), which is also at the very end of sii902x_probe().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Fixes: 21d808405f ("drm/bridge/sii902x: Fix EDID readback")
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240103-si902x-fixes-v1-1-b9fd3e448411@ideasonboard.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240103-si902x-fixes-v1-1-b9fd3e448411@ideasonboard.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 024b32db43 ]
Unlike what is claimed in commit f5aa7d46b0 ("drm/bridge:
parade-ps8640: Provide wait_hpd_asserted() in struct drm_dp_aux"), if
someone manually tries to do an AUX transfer (like via `i2cdump ${bus}
0x50 i`) while the panel is off we don't just get a simple transfer
error. Instead, the whole ps8640 gets thrown for a loop and goes into
a bad state.
Let's put the function to wait for the HPD (and the magical 50 ms
after first reset) back in when we're doing an AUX transfer. This
shouldn't actually make things much slower (assuming the panel is on)
because we should immediately poll and see the HPD high. Mostly this
is just an extra i2c transfer to the bridge.
Fixes: f5aa7d46b0 ("drm/bridge: parade-ps8640: Provide wait_hpd_asserted() in struct drm_dp_aux")
Tested-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Pin-yen Lin <treapking@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231221135548.1.I10f326a9305d57ad32cee7f8d9c60518c8be20fb@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
