[ Upstream commit 256748d548 ]
DP83848 datasheet (section 4.7.2) indicates that the reset pin should be
toggled after the clocks are running. Add the PHY_RST_AFTER_CLK_EN to
make sure that this indication is respected.
In my experience not having this flag enabled would lead to, on some
boots, the wrong MII mode being selected if the PHY was initialized on
the bootloader and was receiving data during Linux boot.
Signed-off-by: Diogo Silva <diogompaissilva@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 34e45ad937 ("net: phy: dp83848: Add TI DP83848 Ethernet PHY")
Link: https://patch.msgid.link/20241102151504.811306-1-paissilva@ld-100007.ds1.internal
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit de96f6a300 upstream.
This change fixes a rare issue where the PHY fails to detect a link
due to incorrect reset behavior.
The SW_RESET definition was incorrectly assigned to bit 14, which is the
Digital Restart bit according to the datasheet. This commit corrects
SW_RESET to bit 15 and assigns DIG_RESTART to bit 14 as per the
datasheet specifications.
The SW_RESET define is only used in the phy_reset function, which fully
re-initializes the PHY after the reset is performed. The change in the
bit definitions should not have any negative impact on the functionality
of the PHY.
v2:
- added Fixes tag
- improved commit message
Cc: stable@vger.kernel.org
Fixes: 5dc39fd5ef ("net: phy: DP83822: Add ability to advertise Fiber connection")
Signed-off-by: Alex Michel <alex.michel@wiedemann-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Message-ID: <AS1P250MB0608A798661549BF83C4B43EA9462@AS1P250MB0608.EURP250.PROD.OUTLOOK.COM>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f50b5d74c6 upstream.
Commit c938ab4da0 ("net: phy: Manual remove LEDs to ensure correct
ordering") correctly fixed a problem with using devm_ but missed
removing the LED entry from the LEDs list.
This cause kernel panic on specific scenario where the port for the PHY
is torn down and up and the kmod for the PHY is removed.
On setting the port down the first time, the assosiacted LEDs are
correctly unregistered. The associated kmod for the PHY is now removed.
The kmod is now added again and the port is now put up, the associated LED
are registered again.
On putting the port down again for the second time after these step, the
LED list now have 4 elements. With the first 2 already unregistered
previously and the 2 new one registered again.
This cause a kernel panic as the first 2 element should have been
removed.
Fix this by correctly removing the element when LED is unregistered.
Reported-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Cc: stable@vger.kernel.org
Fixes: c938ab4da0 ("net: phy: Manual remove LEDs to ensure correct ordering")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241004182759.14032-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a842e443ca ]
When configuring the fiber port, the DP83869 PHY driver incorrectly
calls linkmode_set_bit() with a bit mask (1 << 10) rather than a bit
number (10). This corrupts some other memory location -- in case of
arm64 the priv pointer in the same structure.
Since the advertising flags are updated from supported at the end of the
function the incorrect line isn't needed at all and can be removed.
Fixes: a29de52ba2 ("net: dp83869: Add ability to advertise Fiber connection")
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241002161807.440378-1-inguin@gmx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 225990c487 ]
The PHY built in to the Realtek RTL8366S switch controller was
previously supported by genphy_driver. This PHY does not implement MMD
operations. Since commit 9b01c885be ("net: phy: c22: migrate to
genphy_c45_write_eee_adv()"), MMD register reads have been made during
phy_probe to determine EEE support. For genphy_driver, these reads are
transformed into 802.3 annex 22D clause 45-over-clause 22
mmd_phy_indirect operations that perform MII register writes to
MII_MMD_CTRL and MII_MMD_DATA. This overwrites those two MII registers,
which on this PHY are reserved and have another function, rendering the
PHY unusable while so configured.
Proper support for this PHY is restored by providing a phy_driver that
declares MMD operations as unsupported by using the helper functions
provided for that purpose, while remaining otherwise identical to
genphy_driver.
Fixes: 9b01c885be ("net: phy: c22: migrate to genphy_c45_write_eee_adv()")
Reported-by: Russell Senior <russell@personaltelco.net>
Closes: https://github.com/openwrt/openwrt/issues/15981
Link: https://github.com/openwrt/openwrt/issues/15739
Signed-off-by: Mark Mentovai <mark@mentovai.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c44d3ffd85 ]
When the system resumes from sleep, the phy_init_hw() function invokes
config_init(), which clears all interrupt masks and causes wake events to be
lost in subsequent wake sequences. Remove interrupt mask clearing from
config_init() and preserve relevant masks in config_intr().
Fixes: 7d901a1e87 ("net: phy: add Maxlinear GPY115/21x/24x driver")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e96b293315 ]
If the module is in SFP_MOD_ERROR, `sfp_sm_mod_remove()` will
not be run. As a consequence, `sfp_hwmon_remove()` is not getting
run either, leaving a stale `hwmon` device behind. `sfp_sm_mod_remove()`
itself checks `sfp->sm_mod_state` anyways, so this check was not
really needed in the first place.
Fixes: d2e816c029 ("net: sfp: handle module remove outside state machine")
Signed-off-by: "Csókás, Bence" <csokas.bence@prolan.hu>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240605084251.63502-1-csokas.bence@prolan.hu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a8d3f2e3e ]
KSZ8061 needs to write to a MMD register at driver initialization to fix
an errata. This worked in 5.0 kernel but not in newer kernels. The
issue is the main phylib code no longer resets PHY at the very beginning.
Calling phy resuming code later will reset the chip if it is already
powered down at the beginning. This wipes out the MMD register write.
Solution is to implement a phy resume function for KSZ8061 to take care
of this problem.
Fixes: 232ba3a51c ("net: phy: Micrel KSZ8061: link failure after cable connect")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6149db4997 ]
When the PHY is powered up after powered down most of the registers are
reset, so the PHY setup code needs to be done again. In addition the
interrupt register will need to be setup again so that link status
indication works again.
Fixes: 26dd2974c5 ("net: phy: micrel: Move KSZ9477 errata fixes to PHY driver")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 97eb5d51b4 upstream.
The referenced commit moved the setting of the Autoneg and pause bits
early in sfp_parse_support(). However, we check whether the modes are
empty before using the bitrate to set some modes. Setting these bits
so early causes that test to always be false, preventing this working,
and thus some modules that used to work no longer do.
Move them just before the call to the quirk.
Fixes: 8110633db4 ("net: sfp-bus: allow SFP quirks to override Autoneg and pause bits")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://lore.kernel.org/r/E1rPMJW-001Ahf-L0@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cc: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4fb679040d ]
When the interrupt is enabled, the function lan8841_config_intr tries to
clear any pending interrupts by reading the interrupt status, then
checks the return value for errors and then continue to enable the
interrupt. It has been seen that once the system gets out of sleep mode,
the interrupt status has the value 0x400 meaning that the PHY detected
that the link was in low power. That is correct value but the problem is
that the check is wrong. We try to check for errors but we return an
error also in this case which is not an error. Therefore fix this by
returning only when there is an error.
Fixes: a8f1a19d27 ("net: micrel: Add support for lan8841 PHY")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Suman Ghosh <sumang@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240524085350.359812-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aea27a92a4 ]
The blamed commit started to use the ptp workqueue to get the second
part of the timestamp. And when the port was set down, then this
workqueue is stopped. But if the config option NETWORK_PHY_TIMESTAMPING
is not enabled, then the ptp_clock is not initialized so then it would
crash when it would try to access the delayed work.
So then basically by setting up and then down the port, it would crash.
The fix consists in checking if the ptp_clock is initialized and only
then cancel the delayed work.
Fixes: cc75549548 ("net: micrel: Change to receive timestamp in the frame for lan8841")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c9cd59dbc ]
The DP83869 driver sets the MII bit (needed for PHY to work in MII mode)
only if the op-mode is either DP83869_100M_MEDIA_CONVERT or
DP83869_RGMII_100_BASE.
Some drivers i.e. ICSSG support MII mode with op-mode as
DP83869_RGMII_COPPER_ETHERNET for which the MII bit is not set in dp83869
driver. As a result MII mode on ICSSG doesn't work and below log is seen.
TI DP83869 300b2400.mdio:0f: selected op-mode is not valid with MII mode
icssg-prueth icssg1-eth: couldn't connect to phy ethernet-phy@0
icssg-prueth icssg1-eth: can't phy connect port MII0
Fix this by setting MII bit for DP83869_RGMII_COPPER_ETHERNET op-mode as
well.
Fixes: 94e86ef1b8 ("net: phy: dp83869: support mii mode when rgmii strap cfg is used")
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b5f724b05 ]
Only blink if the link is up on a LED which is programmed to also
indicate link-status.
Otherwise, if both LEDs are in use to indicate different speeds, the
resulting blinking being inverted on LEDs which aren't switched on at
a specific speed is quite counter-intuitive.
Also make sure that state left behind by reset or the bootloader is
recognized correctly including the half-duplex and full-duplex bits as
well as the (unsupported by Linux netdev trigger semantics) link-down
bit.
Fixes: c66937b0f8 ("net: phy: mediatek-ge-soc: support PHY LEDs")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit de99e1ea3a upstream.
There are 2 issues with the blamed commit.
1. When the phy is initialized, it would enable the disabled of UDPv4
checksums. The UDPv6 checksum is already enabled by default. So when
1-step is configured then it would clear these flags.
2. After the 1-step is configured, then if 2-step is configured then the
1-step would be still configured because it is not clearing the flag.
So the sync frames will still have origin timestamps set.
Fix this by reading first the value of the register and then
just change bit 12 as this one determines if the timestamp needs to
be inserted in the frame, without changing any other bits.
Fixes: ece1950283 ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Divya Koppera <divya.koppera@microchip.com>
Link: https://lore.kernel.org/r/20240402071634.2483524-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 32fa4366cc ]
read_poll_timeout inside phy_read_poll_timeout can set val negative
in some cases (for example, __mdiobus_read inside phy_read can return
-EOPNOTSUPP).
Supposedly, commit 4ec7329517 ("net: phylib: fix phy_read*_poll_timeout()")
should fix problems with wrong-signed vals, but I do not see how
as val is sent to phy_read as is and __val = phy_read (not val)
is checked for sign.
Change val type for signed to allow better error handling as done in other
phy_read_poll_timeout callers. This will not fix any error handling
by itself, but allows, for example, to modify cond with appropriate
sign check or check resulting val separately.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 014068dcb5 ("net: phy: genphy_loopback: add link speed configuration")
Signed-off-by: Nikita Kiryushin <kiryushin@ancud.ru>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240315175052.8049-1-kiryushin@ancud.ru
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4469c0c5b1 ]
The phy_get_internal_delay function could try to access to an empty
array in the case that the driver is calling phy_get_internal_delay
without defining delay_values and rx-internal-delay-ps or
tx-internal-delay-ps is defined to 0 in the device-tree.
This will lead to "unable to handle kernel NULL pointer dereference at
virtual address 0". To avoid this kernel oops, the test should be delay
>= 0. As there is already delay < 0 test just before, the test could
only be size == 0.
Fixes: 92252eec91 ("net: phy: Add a helper to return the index for of the internal delay")
Co-developed-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Signed-off-by: Kévin L'hôpital <kevin.lhopital@savoirfairelinux.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3489182b11 ]
Commit bb726b753f ("net: phy: realtek: add support for
RTL8211F(D)(I)-VD-CG") extended support of the driver from the existing
support for RTL8211F(D)(I)-CG PHY to the newer RTL8211F(D)(I)-VD-CG PHY.
While that commit indicated that the RTL8211F_PHYCR2 register is not
supported by the "VD-CG" PHY model and therefore updated the corresponding
section in rtl8211f_config_init() to be invoked conditionally, the call to
"genphy_soft_reset()" was left as-is, when it should have also been invoked
conditionally. This is because the call to "genphy_soft_reset()" was first
introduced by the commit 0a4355c2b7 ("net: phy: realtek: add dt property
to disable CLKOUT clock") since the RTL8211F guide indicates that a PHY
reset should be issued after setting bits in the PHYCR2 register.
As the PHYCR2 register is not applicable to the "VD-CG" PHY model, fix the
rtl8211f_config_init() function by invoking "genphy_soft_reset()"
conditionally based on the presence of the "PHYCR2" register.
Fixes: bb726b753f ("net: phy: realtek: add support for RTL8211F(D)(I)-VD-CG")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240220070007.968762-1-s-vadapalli@ti.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8fdbf3389 ]
Fix passing the wrong reference for config_initr on passing the function
pointer, drop the wrong & from at803x_config_intr in the PHY struct.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 915d25a9d6 ]
In case of no phc we should not return SOFTWARE TIMESTAMPING flags as we do
not know whether the netdev supports of timestamping.
Remove it from the lan8841_ts_info and simply return 0.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aaf632f7ab ]
The HW has the capability to check each frame if it is a PTP frame,
which domain it is, which ptp frame type it is, different ip address in
the frame. And if one of these checks fail then the frame is not
timestamp. Most of these checks were disabled except checking the field
minorVersionPTP inside the PTP header. Meaning that once a partner sends
a frame compliant to 8021AS which has minorVersionPTP set to 1, then the
frame was not timestamp because the HW expected by default a value of 0
in minorVersionPTP. This is exactly the same issue as on lan8841.
Fix this issue by removing this check so the userspace can decide on this.
Fixes: ece1950283 ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Divya Koppera <divya.koppera@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e398822c47 ]
The RZ/G3S SMARC Module has 2 KSZ9131 PHYs. In this setup, the KSZ9131 PHY
is used with the ravb Ethernet driver. It has been discovered that when
bringing the Ethernet interface down/up continuously, e.g., with the
following sh script:
$ while :; do ifconfig eth0 down; ifconfig eth0 up; done
the link speed and duplex are wrong after interrupting the bring down/up
operation even though the Ethernet interface is up. To recover from this
state the following configuration sequence is necessary (executed
manually):
$ ifconfig eth0 down
$ ifconfig eth0 up
The behavior has been identified also on the Microchip SAMA7G5-EK board
which runs the macb driver and uses the same PHY.
The order of PHY-related operations in ravb_open() is as follows:
ravb_open() ->
ravb_phy_start() ->
ravb_phy_init() ->
of_phy_connect() ->
phy_connect_direct() ->
phy_attach_direct() ->
phy_init_hw() ->
phydev->drv->soft_reset()
phydev->drv->config_init()
phydev->drv->config_intr()
phy_resume()
kszphy_resume()
The order of PHY-related operations in ravb_close is as follows:
ravb_close() ->
phy_stop() ->
phy_suspend() ->
kszphy_suspend() ->
genphy_suspend()
// set BMCR_PDOWN bit in MII_BMCR
In genphy_suspend() setting the BMCR_PDWN bit in MII_BMCR switches the PHY
to Software Power-Down (SPD) mode (according to the KSZ9131 datasheet).
Thus, when opening the interface after it has been previously closed (via
ravb_close()), the phydev->drv->config_init() and
phydev->drv->config_intr() reach the KSZ9131 PHY driver via the
ksz9131_config_init() and kszphy_config_intr() functions.
KSZ9131 specifies that the MII management interface remains operational
during SPD (Software Power-Down), but (according to manual):
- Only access to the standard registers (0 through 31) is supported.
- Access to MMD address spaces other than MMD address space 1 is possible
if the spd_clock_gate_override bit is set.
- Access to MMD address space 1 is not possible.
The spd_clock_gate_override bit is not used in the KSZ9131 driver.
ksz9131_config_init() configures RGMII delay, pad skews and LEDs by
accessesing MMD registers other than those in address space 1.
The datasheet for the KSZ9131 does not specify what happens if registers
from an unsupported address space are accessed while the PHY is in SPD.
To fix the issue the .soft_reset method has been instantiated for KSZ9131,
too. This resets the PHY to the default state before doing any
configurations to it, thus switching it out of SPD.
Fixes: bff5b4b373 ("net: phy: micrel: add Microchip KSZ9131 initial driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit acd66c2126 ]
The HW has the capability to check each frame if it is a PTP frame,
which domain it is, which ptp frame type it is, different ip address in
the frame. And if one of these checks fail then the frame is not
timestamp. Most of these checks were disabled except checking the field
minorVersionPTP inside the PTP header. Meaning that once a partner sends
a frame compliant to 8021AS which has minorVersionPTP set to 1, then the
frame was not timestamp because the HW expected by default a value of 0
in minorVersionPTP.
Fix this issue by removing this check so the userspace can decide on this.
Fixes: cafc3662ee ("net: micrel: Add PHC support for lan8841")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Divya Koppera <divya.koppera@microchip.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 02d5fdbf4f upstream.
Background: Turris Omnia (Armada 385); eth2 (mvneta) connected to SFP bus;
SFP module is present, but no fiber connected, so definitely no carrier.
After booting, eth2 is down, but netdev LED trigger surprisingly reports
link active. Then, after "ip link set eth2 up", the link indicator goes
away - as I would have expected it from the beginning.
It turns out, that the default carrier state after netdev creation is
"carrier ok". Some ethernet drivers explicitly call netif_carrier_off
during probing, others (like mvneta) don't - which explains the current
behaviour: only when the device is brought up, phylink_start calls
netif_carrier_off.
Fix this for all drivers using phylink, by calling netif_carrier_off in
phylink_create.
Fixes: 089381b27a ("leds: initial support for Turris Omnia LEDs")
Cc: stable@vger.kernel.org
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Updating the PN is not supported.
Return -EINVAL if update_pn is true.
The following command succeeded, but it should fail because the driver
does not update the PN:
ip macsec set macsec0 tx sa 0 pn 232 on
Fixes: 28c5107aa9 ("net: phy: mscc: macsec support")
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The KSZ9477 errata points out (in 'Module 4') the link up/down problems
when EEE (Energy Efficient Ethernet) is enabled in the device to which
the KSZ9477 tries to auto negotiate.
The suggested workaround is to clear advertisement of EEE for PHYs in
this chip driver.
To avoid regressions with other switch ICs the new MICREL_NO_EEE flag
has been introduced.
Moreover, the in-register disablement of MMD_DEVICE_ID_EEE_ADV.MMD_EEE_ADV
MMD register is removed, as this code is both; now executed too late
(after previous rework of the PHY and DSA for KSZ switches) and not
required as setting all members of eee_broken_modes bit field prevents
the KSZ9477 from advertising EEE.
Fixes: 69d3b36ca0 ("net: dsa: microchip: enable EEE support") # for KSZ9477
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # Confirmed disabled EEE with oscilloscope.
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230905093315.784052-1-lukma@denx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert list_for_each() to list_for_each_entry() where applicable.
No functional changed.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 91a7cda1f4 ("net: phy: Fix race condition on link status
change") all the phy_error() method invocations have been causing the
nested-mutex-lock deadlock because it's normally done in the PHY-driver
threaded IRQ handlers which since that change have been called with the
phydev->lock mutex held. Here is the calls thread:
IRQ: phy_interrupt()
+-> mutex_lock(&phydev->lock); <--------------------+
drv->handle_interrupt() | Deadlock due
+-> ERROR: phy_error() + to the nested
+-> phy_process_error() | mutex lock
+-> mutex_lock(&phydev->lock); <-+
phydev->state = PHY_ERROR;
mutex_unlock(&phydev->lock);
mutex_unlock(&phydev->lock);
The problem can be easily reproduced just by calling phy_error() from any
PHY-device threaded interrupt handler. Fix it by dropping the phydev->lock
mutex lock from the phy_process_error() method and printing a nasty error
message to the system log if the mutex isn't held in the caller execution
context.
Note for the fix to work correctly in the PHY-subsystem itself the
phydev->lock mutex locking must be added to the phy_error_precise()
function.
Link: https://lore.kernel.org/netdev/20230816180944.19262-1-fancer.lancer@gmail.com
Fixes: 91a7cda1f4 ("net: phy: Fix race condition on link status change")
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle extended compliance code 0x1 (SFF8024_ECC_100G_25GAUI_C2M_AOC)
for active optical cables supporting 25G and 100G speeds.
Since the specification makes no statement about transmitter range, and
as the specific sfp module that had been tested features only 2m fiber -
short-range (SR) modes are selected.
The 100G speed is irrelevant because it would require multiple fibers /
multiple SFP28 modules combined under one netdev.
sfp-bus.c only handles a single module per netdev, so only 25Gbps modes
are selected.
sfp_parse_support already handles SFF8024_ECC_100GBASE_SR4_25GBASE_SR
with compatible properties, however that entry is a contradiction in
itself since with SFP(28) 100GBASE_SR4 is impossible - that would likely
be a mode for qsfp modules only.
Add a case for SFF8024_ECC_100G_25GAUI_C2M_AOC selecting 25gbase-r
interface mode and 25000baseSR link mode.
Also enforce SFP28 bitrate limits on the values read from sfp eeprom as
requested by Russell King.
Tested with fs.com S28-AO02 AOC SFP28 module.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
