commit e225128c3f upstream.
When submitting the TLMM test driver, Bjorn reported that some of the test
cases are failing for GPIOs that not are backed by PDC (i.e. "non-wakeup"
GPIOs that are handled directly in pinctrl-msm). Basically, lingering
latched interrupt state is still being delivered at IRQ request time, e.g.:
ok 1 tlmm_test_silent_rising
tlmm_test_silent_falling: ASSERTION FAILED at drivers/pinctrl/qcom/tlmm-test.c:178
Expected atomic_read(&priv->intr_count) == 0, but
atomic_read(&priv->intr_count) == 1 (0x1)
not ok 2 tlmm_test_silent_falling
tlmm_test_silent_low: ASSERTION FAILED at drivers/pinctrl/qcom/tlmm-test.c:178
Expected atomic_read(&priv->intr_count) == 0, but
atomic_read(&priv->intr_count) == 1 (0x1)
not ok 3 tlmm_test_silent_low
ok 4 tlmm_test_silent_high
Whether to report interrupts that came in while the IRQ was unclaimed
doesn't seem to be well-defined in the Linux IRQ API. However, looking
closer at these specific cases, we're actually reporting events that do not
match the interrupt type requested by the driver:
1. After "ok 1 tlmm_test_silent_rising", the GPIO is in low state and
configured for IRQF_TRIGGER_RISING.
2. (a) In preparation for "tlmm_test_silent_falling", the GPIO is switched
to high state. The rising interrupt gets latched.
(b) The GPIO is re-configured for IRQF_TRIGGER_FALLING, but the latched
interrupt isn't cleared.
(c) The IRQ handler is called for the latched interrupt, but there
wasn't any falling edge.
3. (a) For "tlmm_test_silent_low", the GPIO remains in high state.
(b) The GPIO is re-configured for IRQF_TRIGGER_LOW. This seems to
result in a phantom interrupt that gets latched.
(c) The IRQ handler is called for the latched interrupt, but the GPIO
isn't in low state.
4. (a) For "tlmm_test_silent_high", the GPIO is switched to low state.
(b) This doesn't result in a latched interrupt, because RAW_STATUS_EN
was cleared when masking the level-triggered interrupt.
Fix this by clearing the interrupt state whenever making any changes to the
interrupt configuration. This includes previously disabled interrupts, but
also any changes to interrupt polarity or detection type.
With this change, all 16 test cases are now passing for the non-wakeup
GPIOs in the TLMM.
Cc: stable@vger.kernel.org
Fixes: cf9d052aa6 ("pinctrl: qcom: Don't clear pending interrupts when enabling")
Reported-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Closes: https://lore.kernel.org/r/20250227-tlmm-test-v1-1-d18877b4a5db@oss.qualcomm.com/
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Tested-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/20250312-pinctrl-msm-type-latch-v1-1-ce87c561d3d7@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 17013f0acb ]
Tegra devices have an 'sfsel' bit field that determines whether a pin
operates in SFIO (Special Function I/O) or GPIO mode. Currently,
tegra_pinctrl_gpio_disable_free() sets this bit when releasing a GPIO.
However, tegra_pinctrl_set_mux() can be called independently in certain
code paths where gpio_disable_free() is not invoked. In such cases, failing
to set the SFIO mode could lead to incorrect pin configurations, resulting
in functional issues for peripherals relying on SFIO.
This patch ensures that whenever set_mux() is called, the SFIO mode is
correctly set in the Mux Register if the 'sfsel' bit is present. This
prevents situations where the pin remains in GPIO mode despite being
configured for SFIO use.
Fixes: 971dac7123 ("pinctrl: add a driver for NVIDIA Tegra")
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Link: https://lore.kernel.org/20250306050542.16335-1-pshete@nvidia.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ddee69108 ]
Some of the platforms may connect the INT pin via inversion logic
effectively make the triggering to be active-low.
Remove explicit trigger flag to respect the settings from firmware.
Without this change even idling chip produces spurious interrupts
and kernel disables the line in the result:
irq 33: nobody cared (try booting with the "irqpoll" option)
CPU: 0 UID: 0 PID: 125 Comm: irq/33-i2c-INT3 Not tainted 6.12.0-00236-g8b874ed11dae #64
Hardware name: Intel Corp. QUARK/Galileo, BIOS 0x01000900 01/01/2014
...
handlers:
[<86e86bea>] irq_default_primary_handler threaded [<d153e44a>] cy8c95x0_irq_handler [pinctrl_cy8c95x0]
Disabling IRQ #33
Fixes: e6cbbe4294 ("pinctrl: Add Cypress cy8c95x0 support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/20250117142304.596106-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 459915f555 upstream.
Commit 50ebd19e35 ("pinctrl: samsung: drop pin banks references on
error paths") fixed the pin bank references on the error paths of the
probe function, but there is still an error path where this is not done.
If samsung_pinctrl_get_soc_data() does not fail, the child references
will have acquired, and they will need to be released in the error path
of platform_get_irq_optional(), as it is done in the following error
paths within the probe function.
Replace the direct return in the error path with a goto instruction to
the cleanup function.
Cc: stable@vger.kernel.org
Fixes: a382d568f1 ("pinctrl: samsung: Use platform_get_irq_optional() to get the interrupt")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20241106-samsung-pinctrl-put-v1-1-de854e26dd03@gmail.com
[krzysztof: change Fixes SHA to point to commit introducing the return
leading to OF node leak]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f31f33dbb3 ]
Some laptops have pins which are a wake source for S0i3/S3 but which
aren't a wake source for S4/S5 and which cause issues when left unmasked
during hibernation (S4).
For example HP EliteBook 855 G7 has pin #24 that causes instant wakeup
(hibernation failure) if left unmasked (it is a wake source only for
S0i3/S3).
GPIO pin #24 on this platform is likely dedicated to WWAN XMM7360
modem since this pin triggers wake notify to WWAN modem's parent PCIe
port.
Fix this by considering a pin a wake source only if it is marked as one
for the current suspend type (S0i3/S3 vs S4/S5).
Since Z-wake pins only make sense at runtime these were excluded from
both of suspend categories, so pins with only the Z-wake flag set are
effectively treated as non-wake pins.
Fixes: 2fff0b5e1a ("pinctrl: amd: Mask non-wake source pins with interrupt enabled at suspend")
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/d4b2d076366fdd08a0c1cd9b7ecd91dc95e07269.1736184752.git.mail@maciej.szmigiero.name
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9722c3b66e ]
The of_property_for_each_u32() macro needs five parameters, two of which
are primarily meant as internal variables for the macro itself (in the
for() clause). Yet these two parameters are used by a few drivers, and this
can be considered misuse or at least bad practice.
Now that the kernel uses C11 to build, these two parameters can be avoided
by declaring them internally, thus changing this pattern:
struct property *prop;
const __be32 *p;
u32 val;
of_property_for_each_u32(np, "xyz", prop, p, val) { ... }
to this:
u32 val;
of_property_for_each_u32(np, "xyz", val) { ... }
However two variables cannot be declared in the for clause even with C11,
so declare one struct that contain the two variables we actually need. As
the variables inside this struct are not meant to be used by users of this
macro, give the struct instance the noticeable name "_it" so it is visible
during code reviews, helping to avoid new code to use it directly.
Most usages are trivially converted as they do not use those two
parameters, as expected. The non-trivial cases are:
- drivers/clk/clk.c, of_clk_get_parent_name(): easily doable anyway
- drivers/clk/clk-si5351.c, si5351_dt_parse(): this is more complex as the
checks had to be replicated in a different way, making code more verbose
and somewhat uglier, but I refrained from a full rework to keep as much
of the original code untouched having no hardware to test my changes
All the changes have been build tested. The few for which I have the
hardware have been runtime-tested too.
Reviewed-by: Andre Przywara <andre.przywara@arm.com> # drivers/clk/sunxi/clk-simple-gates.c, drivers/clk/sunxi/clk-sun8i-bus-gates.c
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> # drivers/gpio/gpio-brcmstb.c
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> # drivers/irqchip/irq-atmel-aic-common.c
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # drivers/iio/adc/ti_am335x_adc.c
Acked-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com> # drivers/pwm/pwm-samsung.c
Acked-by: Richard Leitner <richard.leitner@linux.dev> # drivers/usb/misc/usb251xb.c
Acked-by: Mark Brown <broonie@kernel.org> # sound/soc/codecs/arizona.c
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com> # sound/soc/codecs/arizona.c
Acked-by: Michael Ellerman <mpe@ellerman.id.au> # arch/powerpc/sysdev/xive/spapr.c
Acked-by: Stephen Boyd <sboyd@kernel.org> # clk
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Acked-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20240724-of_property_for_each_u32-v3-1-bea82ce429e2@bootlin.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Stable-dep-of: 28fa3291ca ("clk: fix an OF node reference leak in of_clk_get_parent_name()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a37eecb705 upstream.
If a device uses MCP23xxx IO expander to receive IRQs, the following
bug can happen:
BUG: sleeping function called from invalid context
at kernel/locking/mutex.c:283
in_atomic(): 1, irqs_disabled(): 1, non_block: 0, ...
preempt_count: 1, expected: 0
...
Call Trace:
...
__might_resched+0x104/0x10e
__might_sleep+0x3e/0x62
mutex_lock+0x20/0x4c
regmap_lock_mutex+0x10/0x18
regmap_update_bits_base+0x2c/0x66
mcp23s08_irq_set_type+0x1ae/0x1d6
__irq_set_trigger+0x56/0x172
__setup_irq+0x1e6/0x646
request_threaded_irq+0xb6/0x160
...
We observed the problem while experimenting with a touchscreen driver which
used MCP23017 IO expander (I2C).
The regmap in the pinctrl-mcp23s08 driver uses a mutex for protection from
concurrent accesses, which is the default for regmaps without .fast_io,
.disable_locking, etc.
mcp23s08_irq_set_type() calls regmap_update_bits_base(), and the latter
locks the mutex.
However, __setup_irq() locks desc->lock spinlock before calling these
functions. As a result, the system tries to lock the mutex whole holding
the spinlock.
It seems, the internal regmap locks are not needed in this driver at all.
mcp->lock seems to protect the regmap from concurrent accesses already,
except, probably, in mcp_pinconf_get/set.
mcp23s08_irq_set_type() and mcp23s08_irq_mask/unmask() are called under
chip_bus_lock(), which calls mcp23s08_irq_bus_lock(). The latter takes
mcp->lock and enables regmap caching, so that the potentially slow I2C
accesses are deferred until chip_bus_unlock().
The accesses to the regmap from mcp23s08_probe_one() do not need additional
locking.
In all remaining places where the regmap is accessed, except
mcp_pinconf_get/set(), the driver already takes mcp->lock.
This patch adds locking in mcp_pinconf_get/set() and disables internal
locking in the regmap config. Among other things, it fixes the sleeping
in atomic context described above.
Fixes: 8f38910ba4 ("pinctrl: mcp23s08: switch to regmap caching")
Cc: stable@vger.kernel.org
Signed-off-by: Evgenii Shatokhin <e.shatokhin@yadro.com>
Link: https://lore.kernel.org/20241209074659.1442898-1-e.shatokhin@yadro.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5a3e85c3c3 ]
When two client of the same gpio call pinctrl_select_state() for the
same functionality, we are seeing NULL pointer issue while accessing
desc->mux_owner.
Let's say two processes A, B executing in pin_request() for the same pin
and process A updates the desc->mux_usecount but not yet updated the
desc->mux_owner while process B see the desc->mux_usecount which got
updated by A path and further executes strcmp and while accessing
desc->mux_owner it crashes with NULL pointer.
Serialize the access to mux related setting with a mutex lock.
cpu0 (process A) cpu1(process B)
pinctrl_select_state() { pinctrl_select_state() {
pin_request() { pin_request() {
...
....
} else {
desc->mux_usecount++;
desc->mux_usecount && strcmp(desc->mux_owner, owner)) {
if (desc->mux_usecount > 1)
return 0;
desc->mux_owner = owner;
} }
Signed-off-by: Mukesh Ojha <quic_mojha@quicinc.com>
Link: https://lore.kernel.org/20241014192930.1539673-1-quic_mojha@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6bc0ebfb1d upstream.
Commit 723e8462a4 ("pinctrl: qcom: spmi-gpio: Fix the GPIO strength
mapping") fixed a long-standing issue in the Qualcomm SPMI PMIC gpio
driver which had the 'low' and 'high' drive strength settings switched
but failed to update the debugfs interface which still gets this wrong.
Fix the debugfs code so that the exported values match the hardware
settings.
Note that this probably means that most devicetrees that try to describe
the firmware settings got this wrong if the settings were derived from
debugfs. Before the above mentioned commit the settings would have
actually matched the firmware settings even if they were described
incorrectly, but now they are inverted.
Fixes: 723e8462a4 ("pinctrl: qcom: spmi-gpio: Fix the GPIO strength mapping")
Fixes: eadff30244 ("pinctrl: Qualcomm SPMI PMIC GPIO pin controller driver")
Cc: Anjelique Melendez <quic_amelende@quicinc.com>
Cc: stable@vger.kernel.org # 3.19
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/20241025121622.1496-1-johan+linaro@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93b8ddc545 upstream.
The current implementation only calls chained_irq_enter() and
chained_irq_exit() if it detects pending interrupts.
```
for (i = 0; i < info->stride; i++) {
uregmap_read(info->map, id_reg + 4 * i, ®);
if (!reg)
continue;
chained_irq_enter(parent_chip, desc);
```
However, in case of GPIO pin configured in level mode and the parent
controller configured in edge mode, GPIO interrupt might be lowered by the
hardware. In the result, if the interrupt is short enough, the parent
interrupt is still pending while the GPIO interrupt is cleared;
chained_irq_enter() never gets called and the system hangs trying to
service the parent interrupt.
Moving chained_irq_enter() and chained_irq_exit() outside the for loop
ensures that they are called even when GPIO interrupt is lowered by the
hardware.
The similar code with chained_irq_enter() / chained_irq_exit() functions
wrapping interrupt checking loop may be found in many other drivers:
```
grep -r -A 10 chained_irq_enter drivers/pinctrl
```
Cc: stable@vger.kernel.org
Signed-off-by: Sergey Matsievskiy <matsievskiysv@gmail.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/20241012105743.12450-2-matsievskiysv@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a9f2b249ad ]
In the probe, if an error occurs after the ti_iodelay_pinconf_init_dev()
call, it is likely that ti_iodelay_pinconf_deinit_dev() should be called,
as already done in the remove function.
Also in ti_iodelay_pinconf_init_dev(), if an error occurs after the first
regmap_update_bits() call, it is also likely that the deinit() function
should be called.
The easier way to fix it is to add a devm_add_action_or_reset() at the
rigtht place to have ti_iodelay_pinconf_deinit_dev() called when needed.
Doing so, the .remove() function can be removed, and the associated
platform_set_drvdata() call in the probe as well.
Fixes: 003910ebc8 ("pinctrl: Introduce TI IOdelay configuration driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/0220fa5b925bd08e361be8206a5438f6229deaac.1720556038.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93650550df ]
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231009083856.222030-21-u.kleine-koenig@pengutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Stable-dep-of: a9f2b249ad ("pinctrl: ti: ti-iodelay: Fix some error handling paths")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 752f387faa ]
pinctrl-at91 currently does not support the gpio-groups devicetree
property and has no pin-range.
Because of this at91 gpios stopped working since patch
commit 2ab73c6d83 ("gpio: Support GPIO controllers without pin-ranges")
This was discussed in the patches
commit fc328a7d1f ("gpio: Revert regression in sysfs-gpio (gpiolib.c)")
commit 56e337f2cf ("Revert "gpio: Revert regression in sysfs-gpio (gpiolib.c)"")
As a workaround manually set pin-range via gpiochip_add_pin_range() until
a) pinctrl-at91 is reworked to support devicetree gpio-groups
b) another solution as mentioned in
commit 56e337f2cf ("Revert "gpio: Revert regression in sysfs-gpio (gpiolib.c)"")
is found
Signed-off-by: Thomas Blocher <thomas.blocher@ek-dev.de>
Link: https://lore.kernel.org/5b992862-355d-f0de-cd3d-ff99e67a4ff1@ek-dev.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 166bf8af91 ]
Despite its name, commit fed74d7527 ("pinctrl: mediatek: common-v2:
Fix bias-disable for PULL_PU_PD_RSEL_TYPE") actually broke bias-disable
for PULL_PU_PD_RSEL_TYPE.
mtk_pinconf_bias_set_combo() tries every bias method supported by the
pin until one succeeds. For PULL_PU_PD_RSEL_TYPE pins, before the
breaking commit, mtk_pinconf_bias_set_rsel() would be called first to
try and set the RSEL value (as well as PU and PD), and if that failed,
the only other valid option was that bias-disable was specified, which
would then be handled by calling mtk_pinconf_bias_set_pu_pd() and
disabling both PU and PD.
The breaking commit misunderstood this logic and added an early "return
0" in mtk_pinconf_bias_set_rsel(). The result was that in the
bias-disable case, the bias was left unchanged, since by returning
success, mtk_pinconf_bias_set_combo() no longer tried calling
mtk_pinconf_bias_set_pu_pd() to disable the bias.
Since the logic for configuring bias-disable on PULL_PU_PD_RSEL_TYPE
pins required mtk_pinconf_bias_set_rsel() to fail first, in that case,
an error was printed to the log, eg:
mt8195-pinctrl 10005000.pinctrl: Not support rsel value 0 Ohm for pin = 29 (GPIO29)
This is what the breaking commit actually got rid of, and likely part of
the reason why that commit was thought to be fixing functionality, while
in reality it was breaking it.
Instead of simply reverting that commit, restore the functionality but
in a way that avoids the error from being printed and makes the code
less confusing:
* Return 0 explicitly if a bias method was successful
* Introduce an extra function mtk_pinconf_bias_set_pu_pd_rsel() that
calls both mtk_pinconf_bias_set_rsel() (only if needed) and
mtk_pinconf_bias_set_pu_pd()
* And analogously for the corresponding getters
Fixes: fed74d7527 ("pinctrl: mediatek: common-v2: Fix bias-disable for PULL_PU_PD_RSEL_TYPE")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/20240808-mtk-rsel-bias-disable-fix-v1-1-1b4e85bf596c@collabora.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 128f71fe01 upstream.
The base iomux offsets for each GPIO pin line are accumulatively
calculated based off iomux width flag in rockchip_pinctrl_get_soc_data.
If the iomux width flag is one of IOMUX_WIDTH_4BIT, IOMUX_WIDTH_3BIT or
IOMUX_WIDTH_2BIT, the base offset for next pin line would increase by 8
bytes, otherwise it would increase by 4 bytes.
Despite most of GPIO2-B iomux have 2-bit data width, which can be fit
into 4 bytes space with write mask, it actually take 8 bytes width for
whole GPIO2-B line.
Commit e8448a6c81 ("pinctrl: rockchip: fix pinmux bits for RK3328
GPIO2-B pins") wrongly set iomux width flag to 0, causing all base
iomux offset for line after GPIO2-B to be calculated wrong. Fix the
iomux width flag to IOMUX_WIDTH_2BIT so the offset after GPIO2-B is
correctly increased by 8, matching the actual width of GPIO2-B iomux.
Fixes: e8448a6c81 ("pinctrl: rockchip: fix pinmux bits for RK3328 GPIO2-B pins")
Cc: stable@vger.kernel.org
Reported-by: Richard Kojedzinszky <richard@kojedz.in>
Closes: https://lore.kernel.org/linux-rockchip/4f29b743202397d60edfb3c725537415@kojedz.in/
Tested-by: Richard Kojedzinszky <richard@kojedz.in>
Signed-off-by: Huang-Huang Bao <i@eh5.me>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Trevor Woerner <twoerner@gmail.com>
Link: https://lore.kernel.org/20240709105428.1176375-1-i@eh5.me
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bfd2428f3a ]
The Pin Multiplex attachment in Rev.1.10 of the R-Car V4H Series
Hardware User's Manual still has two alternate pins named both TCLK3
and TCLK4. To differentiate, the pin control driver uses "TCLK[34]" and
"TCLK[34]_X". In addition, there are alternate pins without suffix, and
with an "_A" or "_B" suffix.
Increase uniformity by adopting R-Car V4M naming:
- Rename "TCLK2_B" to "TCLK2_C",
- Rename "TCLK[12]_A" to "TCLK[12]_B",
- Rename "TCLK[12]" to "TCLK[12]_A",
- Rename "TCLK[34]_A" to "TCLK[34]_C",
- Rename "TCLK[34]_X" to "TCLK[34]_A",
- Rename "TCLK[34]" to "TCLK[34]_B".
Fixes: ad9bb2fec6 ("pinctrl: renesas: Initial R8A779G0 (R-Car V4H) PFC support")
Fixes: 0df46188a5 ("pinctrl: renesas: r8a779g0: Add missing TCLKx_A/TCLKx_B/TCLKx_X")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/2845ff1f8fe1fd8d23d2f307ad5e8eb8243da608.1717754960.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5350f38150 ]
(H)SCIF instance 3 has two alternate pin groups: "hscif3" and
"hscif3_a", resp. "scif3" and "scif3_a", but the actual meanings of the
pins within the groups do not match.
Increase uniformity by adopting R-Car V4M naming:
- Rename "hscif3_a" to "hscif3_b",
- Rename "hscif3" to "hscif3_a",
- Rename "scif3" to "scif3_b".
While at it, remove unneeded separators.
Fixes: ad9bb2fec6 ("pinctrl: renesas: Initial R8A779G0 (R-Car V4H) PFC support")
Fixes: 050442ae4c ("pinctrl: renesas: r8a779g0: Add pins, groups and functions")
Fixes: 213b713255 ("pinctrl: renesas: r8a779g0: Add missing HSCIF3_A")
Fixes: 49e4697656 ("pinctrl: renesas: r8a779g0: Add missing SCIF3")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/61fdde58e369e8070ffd3c5811c089e6219c7ecc.1717754960.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3cf834a166 ]
The Pin Multiplex attachment in Rev.1.10 of the R-Car V4H Series
Hardware User's Manual still has two alternate pin groups (GP0_14-18
and GP1_6-10) each named both HSCIF1 and SCIF1. To differentiate, the
pin control driver uses "(h)scif1" and "(h)scif1_x", which were
considered temporary names until the conflict was sorted out.
Fix this by adopting R-Car V4M naming:
- Rename "(h)scif1" to "(h)scif1_a",
- Rename "(h)scif1_x" to "(h)scif1_b".
Adopt the R-Car V4M naming "(h)scif1_a" and "(h)scif1_b" to increase
uniformity.
While at it, remove unneeded separators.
Fixes: ad9bb2fec6 ("pinctrl: renesas: Initial R8A779G0 (R-Car V4H) PFC support")
Fixes: 050442ae4c ("pinctrl: renesas: r8a779g0: Add pins, groups and functions")
Fixes: cf4f789184 ("pinctrl: renesas: r8a779g0: Add missing HSCIF1_X")
Fixes: 9c151c2be9 ("pinctrl: renesas: r8a779g0: Add missing SCIF1_X")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/5009130d1867e12abf9b231c8838fd05e2b28bee.1717754960.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4976d61ca3 ]
The Pin Multiplex attachment in Rev.1.10 of the R-Car V4H Series
Hardware User's Manual still has two alternate pins named both
"FXR_TXEN[AB]". To differentiate, the pin control driver uses
"FXR_TXEN[AB]" and "FXR_TXEN[AB]_X", which were considered temporary
names until the conflict was sorted out.
Fix this by adopting R-Car V4M naming:
- Rename "FXR_TXEN[AB]" to "FXR_TXEN[AB]_A",
- Rename "FXR_TXEN[AB]_X" to "FXR_TXEN[AB]_B".
Fixes: ad9bb2fec6 ("pinctrl: renesas: Initial R8A779G0 (R-Car V4H) PFC support")
Fixes: 1c2646b5ce ("pinctrl: renesas: r8a779g0: Add missing FlexRay")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/5e1e9abb46c311d4c54450d991072d6d0e66f14c.1717754960.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8da86499d4 upstream.
The SPMI GPIO driver assumes that the parent device is an SPMI device
and accesses random data when backcasting the parent struct device
pointer for non-SPMI devices.
Fortunately this does not seem to cause any issues currently when the
parent device is an I2C client like the PM8008, but this could change if
the structures are reorganised (e.g. using structure randomisation).
Notably the interrupt implementation is also broken for non-SPMI devices.
Also note that the two GPIO pins on PM8008 are used for interrupts and
reset so their practical use should be limited.
Drop the broken GPIO support for PM8008 for now.
Fixes: ea119e5a48 ("pinctrl: qcom-pmic-gpio: Add support for pm8008")
Cc: stable@vger.kernel.org # 5.13
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240529162958.18081-9-johan+linaro@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
