[ Upstream commit bdd5a14e66 ]
The bridge has three bootstrap pins which are sampled to determine the
frequency of the external reference clock. The driver will also
(over)write that setting. But it seems this is racy after the bridge is
enabled. It was observed that although the driver write the correct
value (by sniffing on the I2C bus), the register has the wrong value.
The datasheet states that the GPIO lines have to be stable for at least
5us after asserting the EN signal. Thus, there seems to be some logic
which samples the GPIO lines and this logic appears to overwrite the
register value which was set by the driver. Waiting 20us after
asserting the EN line resolves this issue.
Fixes: a095f15c00 ("drm/bridge: add support for sn65dsi86 bridge driver")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20250821122341.1257286-1-mwalle@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fd2611c13f upstream.
The driver code doesn't have a Phy de-initialization path as yet, and so
it does not clear the phy_initialized flag while suspending. This is a
problem because after resume the driver looks at this flag to determine
if a Phy re-initialization is required or not. It is in fact required
because the hardware is resuming from a suspend, but the driver does not
carry out any re-initialization causing the D-Phy to not work at all.
Call the counterparts of phy_init() and phy_power_on(), that are
phy_exit() and phy_power_off(), from _bridge_post_disable(), and clear
the flags so that the Phy can be initialized again when required.
Fixes: fced5a364d ("drm/bridge: cdns: Convert to phy framework")
Cc: stable@vger.kernel.org
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Signed-off-by: Aradhya Bhatia <aradhya.bhatia@linux.dev>
Link: https://lore.kernel.org/r/20250329113925.68204-3-aradhya.bhatia@linux.dev
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 55e8ff8420 ]
By default, HPD was disabled on SN65DSI86 bridge. When the driver was
added (commit "a095f15c00e27"), the HPD_DISABLE bit was set in pre-enable
call which was moved to other function calls subsequently.
Later on, commit "c312b0df3b13" added detect utility for DP mode. But with
HPD_DISABLE bit set, all the HPD events are disabled[0] and the debounced
state always return 1 (always connected state).
Set HPD_DISABLE bit conditionally based on display sink's connector type.
Since the HPD_STATE is reflected correctly only after waiting for debounce
time (~100-400ms) and adding this delay in detect() is not feasible
owing to the performace impact (glitches and frame drop), remove runtime
calls in detect() and add hpd_enable()/disable() bridge hooks with runtime
calls, to detect hpd properly without any delay.
[0]: <https://www.ti.com/lit/gpn/SN65DSI86> (Pg. 32)
Fixes: c312b0df3b ("drm/bridge: ti-sn65dsi86: Implement bridge connector operations for DP")
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Ernest Van Hoecke <ernest.vanhoecke@toradex.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20250624044835.165708-1-j-choudhary@ti.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 574f5ee2c8 ]
Each bridge instance creates up to four auxiliary devices with different
names. However, their IDs are always zero, causing duplicate filename
errors when a system has multiple bridges:
sysfs: cannot create duplicate filename '/bus/auxiliary/devices/ti_sn65dsi86.gpio.0'
Fix this by using a unique instance ID per bridge instance. The
instance ID is derived from the I2C adapter number and the bridge's I2C
address, to support multiple instances on the same bus.
Fixes: bf73537f41 ("drm/bridge: ti-sn65dsi86: Break GPIO and MIPI-to-eDP bridge into sub-drivers")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/7a68a0e3f927e26edca6040067fb653eb06efb79.1733840089.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 902806baf3 ]
AUDIO_UPDATE bit (Bit 5 of MAIN register 0x4A) needs to be set to 1
while updating Audio InfoFrame information and then set to 0 when done.
Otherwise partially updated Audio InfoFrames could be sent out. Two
cases where this rule were not followed are fixed:
- In adv7511_hdmi_hw_params() make sure AUDIO_UPDATE bit is updated
before/after setting ADV7511_REG_AUDIO_INFOFRAME.
- In audio_startup() use the correct register for clearing
AUDIO_UPDATE bit.
The problem with corrupted audio infoframes were discovered by letting
a HDMI logic analyser check the output of ADV7535.
Note that this patchs replaces writing REG_GC(1) with
REG_INFOFRAME_UPDATE. Bit 5 of REG_GC(1) is positioned within field
GC_PP[3:0] and that field doesn't control audio infoframe and is read-
only. My conclusion therefore was that the author if this code meant to
clear bit 5 of REG_INFOFRAME_UPDATE from the very beginning.
Tested-by: Biju Das <biju.das.jz@bp.renesas.com>
Fixes: 53c515befe ("drm/bridge: adv7511: Add Audio support")
Signed-off-by: Stefan Ekenberg <stefan.ekenberg@axis.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241119-adv7511-audio-info-frame-v4-1-4ae68e76c89c@axis.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5f3f21728 ]
The IT6505 bridge chip has a active low reset line. Since it is a
"reset" and not an "enable" line, the GPIO should be asserted to
put it in reset and deasserted to bring it out of reset during
the power on sequence.
The polarity was inverted when the driver was first introduced, likely
because the device family that was targeted had an inverting level
shifter on the reset line.
The MT8186 Corsola devices already have the IT6505 in their device tree,
but the whole display pipeline is actually disabled and won't be enabled
until some remaining issues are sorted out. The other known user is
the MT8183 Kukui / Jacuzzi family; their device trees currently do not
have the IT6505 included.
Fix the polarity in the driver while there are no actual users.
Fixes: b5c84a9edc ("drm/bridge: add it6505 driver")
Cc: stable@vger.kernel.org
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241029095411.657616-1-wenst@chromium.org
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d343723c7 ]
When a display controller driver uses DRM_BRIDGE_ATTACH_NO_CONNECTOR,
tc358767 will behave properly and skip the creation of the connector.
However, tc_get_display_props(), which is used to find out about the DP
monitor and link, is only called from two places: .atomic_enable() and
tc_connector_get_modes(). The latter is only used when tc358767 creates
its own connector, i.e. when DRM_BRIDGE_ATTACH_NO_CONNECTOR is _not_
set.
Thus, the driver never finds out the link properties before get_edid()
is called. With num_lanes of 0 and link_rate of 0 there are not many
valid modes...
Fix this by adding tc_get_display_props() call at the beginning of
get_edid(), so that we have up to date information before looking at the
modes.
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Closes: https://lore.kernel.org/all/24282420-b4dd-45b3-bb1c-fc37fe4a8205@siemens.com/
Fixes: de5e6c027a ("drm/bridge: tc358767: add drm_panel_bridge support")
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231108-tc358767-v2-2-25c5f70a2159@ideasonboard.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe828fbd87 ]
If the bridge is attached with the DRM_BRIDGE_ATTACH_NO_CONNECTOR flag set,
this driver won't initialize a connector and hence display mode won't be
validated in drm_connector_helper_funcs::mode_valid(). So, move the mode
validation from drm_connector_helper_funcs::mode_valid() to
drm_bridge_funcs::mode_valid(), because the mode validation is always done
for the bridge.
Fixes: 30e2ae943c ("drm/bridge: Introduce LT8912B DSI to HDMI bridge")
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240813091637.1054586-1-victor.liu@nxp.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fc75c40fa ]
The DSI horizontal timing calculations done by the driver seem to often
lead to underflows or overflows, depending on the videomode.
There are two main things the current driver doesn't seem to get right:
DSI HSW and HFP, and VSDly. However, even following Toshiba's
documentation it seems we don't always get a working display.
This patch attempts to fix the horizontal timings for DSI event mode, and
on a system with a DSI->HDMI encoder, a lot of standard HDMI modes now
seem to work. The work relies on Toshiba's documentation, but also quite
a bit on empirical testing.
This also adds timing related debug prints to make it easier to improve
on this later.
The DSI pulse mode has only been tested with a fixed-resolution panel,
which limits the testing of different modes on DSI pulse mode. However,
as the VSDly calculation also affects pulse mode, so this might cause a
regression.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906-tc358768-v4-12-31725f008a50@ideasonboard.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 484436ec5c ]
When the system power resumes, the TTL input of IT6505 may experience
some noise before the video signal stabilizes, necessitating a video
reset. This patch is implemented to prevent a loop of video error
interrupts, which can occur when a video reset in the video FIFO error
interrupt triggers another such interrupt. The patch processes the SCDT
and FIFO error interrupts simultaneously and ignores any video FIFO
error interrupts caused by a video reset.
Fixes: b5c84a9edc ("drm/bridge: add it6505 driver")
Signed-off-by: Kuro Chung <kuro.chung@ite.com.tw>
Signed-off-by: Hermes Wu <hermes.wu@ite.com.tw>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240522065528.1053439-1-kuro.chung@ite.com.tw
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce62600c4d ]
Device managed panel bridge wrappers are created by calling to
drm_panel_bridge_add_typed() and registering a release handler for
clean-up when the device gets unbound.
Since the memory for this bridge is also managed and linked to the panel
device, the release function should not try to free that memory.
Moreover, the call to devm_kfree() inside drm_panel_bridge_remove() will
fail in this case and emit a warning because the panel bridge resource
is no longer on the device resources list (it has been removed from
there before the call to release handlers).
Fixes: 67022227ff ("drm/bridge: Add a devm_ allocator for panel bridge.")
Signed-off-by: Adam Miotk <adam.miotk@arm.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610102739.139852-1-adam.miotk@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad81feb5b6 ]
This reverts commit 8a91b29f1f.
The regulator_disable() added by the original commit solves one kind of
regulator imbalance but adds another one as it allows the regulator to be
disabled one more time than it is enabled in the following scenario:
1. Start video pipeline -> sn65dsi83_atomic_pre_enable -> regulator_enable
2. PLL lock fails -> regulator_disable
3. Stop video pipeline -> sn65dsi83_atomic_disable -> regulator_disable
The reason is clear from the code flow, which looks like this (after
removing unrelated code):
static void sn65dsi83_atomic_pre_enable()
{
regulator_enable(ctx->vcc);
if (PLL failed locking) {
regulator_disable(ctx->vcc); <---- added by patch being reverted
return;
}
}
static void sn65dsi83_atomic_disable()
{
regulator_disable(ctx->vcc);
}
The use case for introducing the additional regulator_disable() was
removing the module for debugging (see link below for the discussion). If
the module is removed after a .atomic_pre_enable, i.e. with an active
pipeline from the DRM point of view, .atomic_disable is not called and thus
the regulator would not be disabled.
According to the discussion however there is no actual use case for
removing the module with an active pipeline, except for
debugging/development.
On the other hand, the occurrence of a PLL lock failure is possible due to
any physical reason (e.g. a temporary hardware failure for electrical
reasons) so handling it gracefully should be supported. As there is no way
for .atomic[_pre]_enable to report an error to the core, the only clean way
to support it is calling regulator_disabled() only in .atomic_disable,
unconditionally, as it was before.
Link: https://lore.kernel.org/all/15244220.uLZWGnKmhe@steina-w/
Fixes: 8a91b29f1f ("drm/bridge: ti-sn65dsi83: Fix enable error path")
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240426122259.46808-1-luca.ceresoli@bootlin.com
(cherry picked from commit 2940ee03b2)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30ea09a182 ]
The bridge always uses 24bpp internally. Therefore, for jeida-18
mapping we need to discard the lowest two bits for each channel and thus
starting with LV_[RGB]2. jeida-24 has the same mapping but uses four
lanes instead of three, with the forth pair transmitting the lowest two
bits of each channel. Thus, the mapping between jeida-18 and jeida-24
is actually the same, except that one channel is turned off (by
selecting the RGB666 format in VPCTRL).
While at it, remove the bogus comment about the hardware default because
the default is overwritten in any case.
Tested with a jeida-18 display (Evervision VGG644804).
Fixes: b26975593b ("display/drm/bridge: TC358775 DSI/LVDS driver")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240225062008.33191-5-tony@atomide.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
