[ Upstream commit db5a5406fb ]
It’s possible for more than one async command to be in flight from
__nvmet_fc_send_ls_req. For each command, a tgtport reference is taken.
In the current code, only one put work item is queued at a time, which
results in a leaked reference.
To fix this, move the work item to the nvmet_fc_ls_req_op struct, which
already tracks all resources related to the command.
Fixes: 710c69dbac ("nvmet-fc: avoid deadlock on delete association path")
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Daniel Wagner <wagi@kernel.org>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b2c214a95 ]
NVMe devices from multiple vendors appear to get stuck in a reset state
that we can't get out of with an NVMe level Controller Reset. The kernel
would report these with messages that look like:
Device not ready; aborting reset, CSTS=0x1
These have historically required a power cycle to make them usable
again, but in many cases, a PCIe FLR is sufficient to restart operation
without a power cycle. Try it if the initial controller reset fails
during any nvme reset attempt.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Nitesh Shetty <nj.shetty@samsung.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71257925e8 ]
Procedures for nvme-mpath IO accounting:
1) initialize nvme_request and clear flags;
2) set NVME_MPATH_IO_STATS and increase inflight counter when IO
started;
3) check NVME_MPATH_IO_STATS and decrease inflight counter when IO is
done;
However, for the case nvme_fail_nonready_command(), both step 1) and 2)
are skipped, and if old nvme_request set NVME_MPATH_IO_STATS and then
request is reused, step 3) will still be executed, causing inflight I/O
counter to be negative.
Fix the problem by clearing nvme_request in nvme_fail_nonready_command().
Fixes: ea5e5f42cd ("nvme-fabrics: avoid double completions in nvmf_fail_nonready_command")
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Closes: https://lore.kernel.org/all/CAHj4cs_+dauobyYyP805t33WMJVzOWj=7+51p4_j9rA63D9sog@mail.gmail.com/
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80d7762e0a ]
When inserting a namespace into the controller's namespace list, the
function uses list_add_rcu() when the namespace is inserted in the middle
of the list, but falls back to a regular list_add() when adding at the
head of the list.
This inconsistency could lead to race conditions during concurrent
access, as users might observe a partially updated list. Fix this by
consistently using list_add_rcu() in both code paths to ensure proper
RCU protection throughout the entire function.
Fixes: be647e2c76 ("nvme: use srcu for iterating namespace list")
Signed-off-by: Zheng Qixing <zhengqixing@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 9ce6c9875f upstream.
Currently NVMe uring_cmd completions will complete locally, if they are
polled. This is done because those completions are always invoked from
task context. And while that is true, there's no guarantee that it's
invoked under the right ring context, or even task. If someone does
NVMe passthrough via multiple threads and with a limited number of
poll queues, then ringA may find completions from ringB. For that case,
completing the request may not be sound.
Always just punt the passthrough completions via task_work, which will
redirect the completion, if needed.
Cc: stable@vger.kernel.org
Fixes: 585079b6e4 ("nvme: wire up async polling for io passthrough commands")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 47a827cd79 ]
The abort handling logic expects that the state and the fcpreq are only
accessed when holding the reqlock lock.
While at it, only handle the aborts in the abort handler.
Signed-off-by: Daniel Wagner <wagi@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e765bf89f4 ]
This commit adds the NVME_QUIRK_NO_DEEPEST_PS quirk for device
[126f:2262], which belongs to device SOLIDIGM P44 Pro SSDPFKKW020X7
The device frequently have trouble exiting the deepest power state (5),
resulting in the entire disk being unresponsive.
Verified by setting nvme_core.default_ps_max_latency_us=10000 and
observing the expected behavior.
Signed-off-by: Ilya Guterman <amfernusus@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 40696426b8 ]
The only reason nvme_pci_npages_prp() could be used as a compile-time
known result in BUILD_BUG_ON() is because the compiler was always choosing
to inline the function. Under special circumstances (sanitizer coverage
functions disabled for __init functions on ARCH=um), the compiler decided
to stop inlining it:
drivers/nvme/host/pci.c: In function 'nvme_init':
include/linux/compiler_types.h:557:45: error: call to '__compiletime_assert_678' declared with attribute error: BUILD_BUG_ON failed: nvme_pci_npages_prp() > NVME_MAX_NR_ALLOCATIONS
557 | _compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
| ^
include/linux/compiler_types.h:538:25: note: in definition of macro '__compiletime_assert'
538 | prefix ## suffix(); \
| ^~~~~~
include/linux/compiler_types.h:557:9: note: in expansion of macro '_compiletime_assert'
557 | _compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
| ^~~~~~~~~~~~~~~~~~~
include/linux/build_bug.h:39:37: note: in expansion of macro 'compiletime_assert'
39 | #define BUILD_BUG_ON_MSG(cond, msg) compiletime_assert(!(cond), msg)
| ^~~~~~~~~~~~~~~~~~
include/linux/build_bug.h:50:9: note: in expansion of macro 'BUILD_BUG_ON_MSG'
50 | BUILD_BUG_ON_MSG(condition, "BUILD_BUG_ON failed: " #condition)
| ^~~~~~~~~~~~~~~~
drivers/nvme/host/pci.c:3804:9: note: in expansion of macro 'BUILD_BUG_ON'
3804 | BUILD_BUG_ON(nvme_pci_npages_prp() > NVME_MAX_NR_ALLOCATIONS);
| ^~~~~~~~~~~~
Force it to be __always_inline to make sure it is always available for
use with BUILD_BUG_ON().
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202505061846.12FMyRjj-lkp@intel.com/
Fixes: c372cdd1ef ("nvme-pci: iod npages fits in s8")
Signed-off-by: Kees Cook <kees@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 650415fca0 ]
The original nvme subsystem design didn't have a CONNECTING state; the
state machine allowed transitions from RESETTING to LIVE directly.
With the introduction of nvme fabrics the CONNECTING state was
introduce. Over time the nvme-pci started to use the CONNECTING state as
well.
Eventually, a bug fix for the nvme-fc started to depend that the only
valid transition to LIVE was from CONNECTING. Though this change didn't
update the firmware update handler which was still depending on
RESETTING to LIVE transition.
The simplest way to address it for the time being is to switch into
CONNECTING state before going to LIVE state.
Fixes: d2fe192348 ("nvme: only allow entering LIVE from CONNECTING state")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Daniel Wagner <wagi@kernel.org>
Closes: https://lore.kernel.org/all/0134ea15-8d5f-41f7-9e9a-d7e6d82accaa@roeck-us.net
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77e40bbce9 ]
This patch addresses a data corruption issue observed in nvme-tcp during
testing.
In an NVMe native multipath setup, when an I/O timeout occurs, all
inflight I/Os are canceled almost immediately after the kernel socket is
shut down. These canceled I/Os are reported as host path errors,
triggering a failover that succeeds on a different path.
However, at this point, the original I/O may still be outstanding in the
host's network transmission path (e.g., the NIC’s TX queue). From the
user-space app's perspective, the buffer associated with the I/O is
considered completed since they're acked on the different path and may
be reused for new I/O requests.
Because nvme-tcp enables zero-copy by default in the transmission path,
this can lead to corrupted data being sent to the original target,
ultimately causing data corruption.
We can reproduce this data corruption by injecting delay on one path and
triggering i/o timeout.
To prevent this issue, this change ensures that all inflight
transmissions are fully completed from host's perspective before
returning from queue stop. To handle concurrent I/O timeout from multiple
namespaces under the same controller, always wait in queue stop
regardless of queue's state.
This aligns with the behavior of queue stopping in other NVMe fabric
transports.
Fixes: 3f2304f8c6 ("nvme-tcp: add NVMe over TCP host driver")
Signed-off-by: Michael Liang <mliang@purestorage.com>
Reviewed-by: Mohamed Khalfella <mkhalfella@purestorage.com>
Reviewed-by: Randy Jennings <randyj@purestorage.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a75401227e ]
A zero return means the reset was successfully scheduled. We don't want
to unquiesce the queues while the reset_work is pending, as that will
just flush out requeued requests to a failed completion.
Fixes: 71a5bb153b ("nvme: ensure disabling pairs with unquiesce")
Reported-by: Dhankaran Singh Ajravat <dhankaran@meta.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 26d7fb4fd4 upstream.
Commit 62baf70c32 caused the ANA log page to be re-read, even on
controllers that do not support ANA. While this should generally
harmless, some controllers hang on the unsupported log page and
never finish probing.
Fixes: 62baf70c32 ("nvme: re-read ANA log page after ns scan completes")
Signed-off-by: Hannes Reinecke <hare@kernel.org>
Tested-by: Srikanth Aithal <sraithal@amd.com>
[hch: more detailed commit message]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 70289ae5ca ]
Do not leak the tgtport reference when the work is already scheduled.
Signed-off-by: Daniel Wagner <wagi@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0b26ad0e1 ]
The reference counting code can be simplified. Instead taking a tgtport
refrerence at the beginning of nvmet_fc_alloc_hostport and put it back
if not a new hostport object is allocated, only take it when a new
hostport object is allocated.
Signed-off-by: Daniel Wagner <wagi@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3105f54a5 ]
The function returns bool so we should return false, not NULL. No
functional changes are expected.
Signed-off-by: Uday Shankar <ushankar@purestorage.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62baf70c32 ]
When scanning for new namespaces we might have missed an ANA AEN.
The NVMe base spec (NVMe Base Specification v2.1, Figure 151 'Asynchonous
Event Information - Notice': Asymmetric Namespace Access Change) states:
A controller shall not send this even if an Attached Namespace
Attribute Changed asynchronous event [...] is sent for the same event.
so we need to re-read the ANA log page after we rescanned the namespace
list to update the ANA states of the new namespaces.
Signed-off-by: Hannes Reinecke <hare@kernel.org>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9546ad1a9b ]
Scanning for namespaces can take some time, so if the target is
reconfigured while the scan is running we may miss a Attached Namespace
Attribute Changed AEN.
Check if the NVME_AER_NOTICE_NS_CHANGED bit is set once the scan has
finished, and requeue scanning to pick up any missed change.
Signed-off-by: Hannes Reinecke <hare@kernel.org>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1b304c006b upstream.
The functions nvmet_fc_iodnum() and nvmet_fc_fodnum() are currently
unutilized.
Following commit c53432030d ("nvme-fabrics: Add target support for FC
transport"), which introduced these two functions, they have not been
used at all in practice.
Remove them to resolve the compiler warnings.
Fix follow errors with clang-19 when W=1e:
drivers/nvme/target/fc.c:177:1: error: unused function 'nvmet_fc_iodnum' [-Werror,-Wunused-function]
177 | nvmet_fc_iodnum(struct nvmet_fc_ls_iod *iodptr)
| ^~~~~~~~~~~~~~~
drivers/nvme/target/fc.c:183:1: error: unused function 'nvmet_fc_fodnum' [-Werror,-Wunused-function]
183 | nvmet_fc_fodnum(struct nvmet_fc_fcp_iod *fodptr)
| ^~~~~~~~~~~~~~~
2 errors generated.
make[8]: *** [scripts/Makefile.build:207: drivers/nvme/target/fc.o] Error 1
make[7]: *** [scripts/Makefile.build:465: drivers/nvme/target] Error 2
make[6]: *** [scripts/Makefile.build:465: drivers/nvme] Error 2
make[6]: *** Waiting for unfinished jobs....
Fixes: c53432030d ("nvme-fabrics: Add target support for FC transport")
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5858b68755 upstream.
Kernel will hang on destroy admin_q while we create ctrl failed, such
as following calltrace:
PID: 23644 TASK: ff2d52b40f439fc0 CPU: 2 COMMAND: "nvme"
#0 [ff61d23de260fb78] __schedule at ffffffff8323bc15
#1 [ff61d23de260fc08] schedule at ffffffff8323c014
#2 [ff61d23de260fc28] blk_mq_freeze_queue_wait at ffffffff82a3dba1
#3 [ff61d23de260fc78] blk_freeze_queue at ffffffff82a4113a
#4 [ff61d23de260fc90] blk_cleanup_queue at ffffffff82a33006
#5 [ff61d23de260fcb0] nvme_rdma_destroy_admin_queue at ffffffffc12686ce
#6 [ff61d23de260fcc8] nvme_rdma_setup_ctrl at ffffffffc1268ced
#7 [ff61d23de260fd28] nvme_rdma_create_ctrl at ffffffffc126919b
#8 [ff61d23de260fd68] nvmf_dev_write at ffffffffc024f362
#9 [ff61d23de260fe38] vfs_write at ffffffff827d5f25
RIP: 00007fda7891d574 RSP: 00007ffe2ef06958 RFLAGS: 00000202
RAX: ffffffffffffffda RBX: 000055e8122a4d90 RCX: 00007fda7891d574
RDX: 000000000000012b RSI: 000055e8122a4d90 RDI: 0000000000000004
RBP: 00007ffe2ef079c0 R8: 000000000000012b R9: 000055e8122a4d90
R10: 0000000000000000 R11: 0000000000000202 R12: 0000000000000004
R13: 000055e8122923c0 R14: 000000000000012b R15: 00007fda78a54500
ORIG_RAX: 0000000000000001 CS: 0033 SS: 002b
This due to we have quiesced admi_q before cancel requests, but forgot
to unquiesce before destroy it, as a result we fail to drain the
pending requests, and hang on blk_mq_freeze_queue_wait() forever. Here
try to reuse nvme_rdma_teardown_admin_queue() to fix this issue and
simplify the code.
Fixes: 958dc1d32c ("nvme-rdma: add clean action for failed reconnection")
Reported-by: Yingfu.zhou <yingfu.zhou@shopee.com>
Signed-off-by: Chunguang.xu <chunguang.xu@shopee.com>
Signed-off-by: Yue.zhao <yue.zhao@shopee.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
[Minor context change fixed]
Signed-off-by: Feng Liu <Feng.Liu3@windriver.com>
Signed-off-by: He Zhe <Zhe.He@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2b5f0c5bc8 ]
The newly element to be added to the list is the first argument of
list_add_tail. This fix is missing dcfad4ab4d ("nvmet-fcloop: swap
the list_add_tail arguments").
Fixes: 437c0b824d ("nvme-fcloop: add target to host LS request support")
Signed-off-by: Daniel Wagner <wagi@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f674e7b67 ]
The PCIe error handling has the nvme driver quiesce the device, attempt
to restart it, then wait for that restart to complete.
A PCIe DPC event also toggles the PCIe link. If the slot doesn't have
out-of-band presence detection, this will trigger a pciehp
re-enumeration.
The error handling that calls nvme_error_resume is holding the device
lock while this happens. This lock blocks pciehp's request to disconnect
the driver from proceeding.
Meanwhile the nvme's reset can't make forward progress because its
device isn't there anymore with outstanding IO, and the timeout handler
won't do anything to fix it because the device is undergoing error
handling.
End result: deadlocked.
Fix this by having the timeout handler short cut the disabling for a
disconnected PCIe device. The downside is that we're relying on an IO
timeout to clean up this mess, which could be a minute by default.
Tested-by: Nilay Shroff <nilay@linux.ibm.com>
Reviewed-by: Nilay Shroff <nilay@linux.ibm.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56cf7ef0d4 ]
The PCI P2PDMA code will register the CMB block to the memory
hot-plugging subsystem, which have an alignment requirement. Memory
blocks that do not satisfy this alignment requirement (usually 2MB) will
lead to a WARNING from memory hotplugging.
Verify the CMB block's address and size against the alignment and only
try to send CMB blocks compatible with it to prevent this warning.
Tested on Intel DC D4502 SSD, which has a 512K CMB block that is too
small for memory hotplugging (thus PCI P2PDMA).
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a3572e10f ]
CMB decoding should get disabled when the CMB block isn't successfully
registered to P2P DMA subsystem.
Clean up the CMBMSC register in this error handling codepath to disable
CMB decoding (and CMBLOC/CMBSZ registers).
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit afb41b08c4 upstream.
In H2CTermReq, a FES with value 0x05 means "R2T Limit Exceeded"; but
in C2HTermReq the same value has a different meaning (Data Transfer Limit
Exceeded).
Fixes: 84e009042d ("nvme-tcp: add basic support for the C2HTermReq PDU")
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f13409bb3f upstream.
It's not possible to call nvme_state_ctrl_state with holding a spin
lock, because nvme_state_ctrl_state calls cancel_delayed_work_sync
when fastfail is enabled.
Instead syncing the ASSOC_FLAG and state transitions using a lock, it's
possible to only rely on the state machine transitions. That means
nvme_fc_ctrl_connectivity_loss should unconditionally call
nvme_reset_ctrl which avoids the read race on the ctrl state variable.
Actually, it's not necessary to test in which state the ctrl is, the
reset work will only scheduled when the state machine is in LIVE state.
In nvme_fc_create_association, the LIVE state can only be entered if it
was previously CONNECTING. If this is not possible then the reset
handler got triggered. Thus just error out here.
Fixes: ee59e3820c ("nvme-fc: do not ignore connectivity loss during connecting")
Closes: https://lore.kernel.org/all/denqwui6sl5erqmz2gvrwueyxakl5txzbbiu3fgebryzrfxunm@iwxuthct377m/
Reported-by: Shinichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Daniel Wagner <wagi@kernel.org>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d2fe192348 ]
The fabric transports and also the PCI transport are not entering the
LIVE state from NEW or RESETTING. This makes the state machine more
restrictive and allows to catch not supported state transitions, e.g.
directly switching from RESETTING to LIVE.
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Daniel Wagner <wagi@kernel.org>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3988ac1c67 ]
The queue state checking in nvmet_rdma_recv_done is not in queue state
lock.Queue state can transfer to LIVE in cm establish handler between
state checking and state lock here, cause a silent drop of nvme connect
cmd.
Recheck queue state whether in LIVE state in state lock to prevent this
issue.
Signed-off-by: Ruozhu Li <david.li@jaguarmicro.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84e009042d ]
Previously, the NVMe/TCP host driver did not handle the C2HTermReq PDU,
instead printing "unsupported pdu type (3)" when received. This patch adds
support for processing the C2HTermReq PDU, allowing the driver
to print the Fatal Error Status field.
Example of output:
nvme nvme4: Received C2HTermReq (FES = Invalid PDU Header Field)
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fcd8754458 ]
In order for two Acer FA100 SSDs to work in one PC (in the case of
myself, a Lenovo Legion T5 28IMB05), and not show one drive and not
the other, and sometimes mix up what drive shows up (randomly), these
two lines of code need to be added, and then both of the SSDs will
show up and not conflict when booting off of one of them. If you boot
up your computer with both SSDs installed without this patch, you may
also randomly get into a kernel panic (if the initrd is not set up) or
stuck in the initrd "/init" process, it is set up, however, if you do
apply this patch, there should not be problems with booting or seeing
both contents of the drive. Tested with the btrfs filesystem with a
RAID configuration of having the root drive '/' combined to make two
256GB Acer FA100 SSDs become 512GB in total storage.
Kernel Logs with patch applied (`dmesg -t | grep -i nvm`):
```
...
nvme 0000:04:00.0: platform quirk: setting simple suspend
nvme nvme0: pci function 0000:04:00.0
nvme 0000:05:00.0: platform quirk: setting simple suspend
nvme nvme1: pci function 0000:05:00.0
nvme nvme1: missing or invalid SUBNQN field.
nvme nvme1: allocated 64 MiB host memory buffer.
nvme nvme0: missing or invalid SUBNQN field.
nvme nvme0: allocated 64 MiB host memory buffer.
nvme nvme1: 8/0/0 default/read/poll queues
nvme nvme1: Ignoring bogus Namespace Identifiers
nvme nvme0: 8/0/0 default/read/poll queues
nvme nvme0: Ignoring bogus Namespace Identifiers
nvme0n1: p1 p2
...
```
Kernel Logs with patch not applied (`dmesg -t | grep -i nvm`):
```
...
nvme 0000:04:00.0: platform quirk: setting simple suspend
nvme nvme0: pci function 0000:04:00.0
nvme 0000:05:00.0: platform quirk: setting simple suspend
nvme nvme1: pci function 0000:05:00.0
nvme nvme0: missing or invalid SUBNQN field.
nvme nvme1: missing or invalid SUBNQN field.
nvme nvme0: allocated 64 MiB host memory buffer.
nvme nvme1: allocated 64 MiB host memory buffer.
nvme nvme0: 8/0/0 default/read/poll queues
nvme nvme1: 8/0/0 default/read/poll queues
nvme nvme1: globally duplicate IDs for nsid 1
nvme nvme1: VID:DID 1dbe:5216 model:Acer SSD FA100 256GB firmware:1.Z.J.2X
nvme0n1: p1 p2
...
```
Signed-off-by: Christopher Lentocha <christopherericlentocha@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee59e3820c ]
When a connectivity loss occurs while nvme_fc_create_assocation is
being executed, it's possible that the ctrl ends up stuck in the LIVE
state:
1) nvme nvme10: NVME-FC{10}: create association : ...
2) nvme nvme10: NVME-FC{10}: controller connectivity lost.
Awaiting Reconnect
nvme nvme10: queue_size 128 > ctrl maxcmd 32, reducing to maxcmd
3) nvme nvme10: Could not set queue count (880)
nvme nvme10: Failed to configure AEN (cfg 900)
4) nvme nvme10: NVME-FC{10}: controller connect complete
5) nvme nvme10: failed nvme_keep_alive_end_io error=4
A connection attempt starts 1) and the ctrl is in state CONNECTING.
Shortly after the LLDD driver detects a connection lost event and calls
nvme_fc_ctrl_connectivity_loss 2). Because we are still in CONNECTING
state, this event is ignored.
nvme_fc_create_association continues to run in parallel and tries to
communicate with the controller and these commands will fail. Though
these errors are filtered out, e.g in 3) setting the I/O queues numbers
fails which leads to an early exit in nvme_fc_create_io_queues. Because
the number of IO queues is 0 at this point, there is nothing left in
nvme_fc_create_association which could detected the connection drop.
Thus the ctrl enters LIVE state 4).
Eventually the keep alive handler times out 5) but because nothing is
being done, the ctrl stays in LIVE state.
There is already the ASSOC_FAILED flag to track connectivity loss event
but this bit is set too late in the recovery code path. Move this into
the connectivity loss event handler and synchronize it with the state
change. This ensures that the ASSOC_FAILED flag is seen by
nvme_fc_create_io_queues and it does not enter the LIVE state after a
connectivity loss event. If the connectivity loss event happens after we
entered the LIVE state the normal error recovery path is executed.
Signed-off-by: Daniel Wagner <wagi@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3d380eded ]
The initial controller initialization mimiks the reconnect loop
behavior by switching from NEW to RESETTING and then to CONNECTING.
The transition from NEW to CONNECTING is a valid transition, so there is
no point entering the RESETTING state. TCP and RDMA also transition
directly to CONNECTING state.
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Daniel Wagner <wagi@kernel.org>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a16f88964c ]
The order in which queue->cmd and rcv_state are updated is crucial.
If these assignments are reordered by the compiler, the worker might not
get queued in nvmet_tcp_queue_response(), hanging the IO. to enforce the
the correct reordering, set rcv_state using smp_store_release().
Fixes: bdaf132791 ("nvmet-tcp: fix a segmentation fault during io parsing error")
Signed-off-by: Meir Elisha <meir.elisha@volumez.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 487a3ea7b1 ]
nvme_validate_passthru_nsid() logs an err message whose format string is
split over 2 lines. There is a missing space between the two pieces,
resulting in log lines like "... does not match nsid (1)of namespace".
Add the missing space between ")" and "of". Also combine the format
string pieces onto a single line to make the err message easier to grep.
Fixes: e7d4b5493a ("nvme: factor out a nvme_validate_passthru_nsid helper")
Signed-off-by: Caleb Sander Mateos <csander@purestorage.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 11cb3529d1 upstream.
On the TUXEDO InfinityBook Pro Gen9 Intel, a Samsung 990 Evo NVMe leads to
a high power consumption in s2idle sleep (4 watts).
This patch applies 'Force No Simple Suspend' quirk to achieve a sleep with
a lower power consumption, typically around 1.2 watts.
Signed-off-by: Georg Gottleuber <ggo@tuxedocomputers.com>
Cc: stable@vger.kernel.org
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dbf2bb1a13 upstream.
On the TUXEDO InfinityFlex, a Samsung 990 Evo NVMe leads to a high power
consumption in s2idle sleep (4 watts).
This patch applies 'Force No Simple Suspend' quirk to achieve a sleep with
a lower power consumption, typically around 1.4 watts.
Signed-off-by: Georg Gottleuber <ggo@tuxedocomputers.com>
Cc: stable@vger.kernel.org
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c8ed6cb5d3 ]
Do not access the state variable directly, instead use proper
synchronization so not stale data is read.
Fixes: e6e7f7ac03 ("nvme: ensure reset state check ordering")
Signed-off-by: Daniel Wagner <wagi@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 294b2b7516 ]
When the set feature attempts fails with any NVME status code set in
nvme_set_queue_count, the function still report success. Though the
numbers of queues set to 0. This is done to support controllers in
degraded state (the admin queue is still up and running but no IO
queues).
Though there is an exception. When nvme_set_features reports an host
path error, nvme_set_queue_count should propagate this error as the
connectivity is lost, which means also the admin queue is not working
anymore.
Fixes: 9a0be7abb6 ("nvme: refactor set_queue_count")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Daniel Wagner <wagi@kernel.org>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 170e086ad3 ]
nvme_init_effects_log() returns failure when kzalloc() is successful,
which is obviously wrong and causes failures to boot. Correct the
check.
Fixes: d4a95adeab ("nvme: Add error path for xa_store in nvme_init_effects")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4a95adeab ]
The xa_store() may fail due to memory allocation failure because there
is no guarantee that the index NVME_CSI_NVM is already used. This fix
introduces a new function to handle the error path.
Fixes: cc115cbe12 ("nvme: always initialize known command effects")
Signed-off-by: Keisuke Nishimura <keisuke.nishimura@inria.fr>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac32057acc ]
The xa_store() may fail due to memory allocation failure because there
is no guarantee that the index csi is already used. This fix adds an
error check of the return value of xa_store() in nvme_get_effects_log().
Fixes: 1cf7a12e09 ("nvme: use an xarray to lookup the Commands Supported and Effects log")
Signed-off-by: Keisuke Nishimura <keisuke.nishimura@inria.fr>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b579d6fdc3 ]
Ensure we propagate npwg to the target as well instead
of assuming its the same logical blocks per physical block.
This ensures devices with large IUs information properly
propagated on the target.
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebefac5647 ]
We initially introduced a quick fix limiting the queue depth to 1 as
experimentation showed that it fixed data corruption on 64GB steamdecks.
Further experimentation revealed corruption only happens when the last
PRP data element aligns to the end of the page boundary. The device
appears to treat this as a PRP chain to a new list instead of the data
element that it actually is. This implementation is in violation of the
spec. Encountering this errata with the Linux driver requires the host
request a 128k transfer and coincidently be handed the last small pool
dma buffer within a page.
The QD1 quirk effectly works around this because the last data PRP
always was at a 248 byte offset from the page start, so it never
appeared at the end of the page, but comes at the expense of throttling
IO and wasting the remainder of the PRP page beyond 256 bytes. Also to
note, the MDTS on these devices is small enough that the "large" prp
pool can hold enough PRP elements to never reach the end, so that pool
is not a problem either.
Introduce a new quirk to ensure the small pool is always aligned such
that the last PRP element can't appear a the end of the page. This comes
at the expense of wasting 256 bytes per small pool page allocated.
Link: https://lore.kernel.org/linux-nvme/20241113043151.GA20077@lst.de/T/#u
Fixes: 83bdfcbdbe ("nvme-pci: qdepth 1 quirk")
Cc: Paweł Anikiel <panikiel@google.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8448828216 ]
This reverts commit d06923670b.
It was realized that the fix implemented to contain the race condition
among the keep alive task and the fabric shutdown code path in the commit
d06923670b5ia ("nvme: make keep-alive synchronous operation") is not
optimal. The reason being keep-alive runs under the workqueue and making
it synchronous would waste a workqueue context.
Furthermore, we later found that the above race condition is a regression
caused due to the changes implemented in commit a54a93d0e3 ("nvme: move
stopping keep-alive into nvme_uninit_ctrl()"). So we decided to revert the
commit d06923670b ("nvme: make keep-alive synchronous operation") and
then fix the regression.
Link: https://lore.kernel.org/all/196f4013-3bbf-43ff-98b4-9cb2a96c20c2@grimberg.me/
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Nilay Shroff <nilay@linux.ibm.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 599d9f3a10 ]
We no more need acquiring ctrl->lock before accessing the
NVMe controller state and instead we can now use the helper
nvme_ctrl_state. So replace the use of ctrl->lock from
nvme_keep_alive_finish function with nvme_ctrl_state call.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nilay Shroff <nilay@linux.ibm.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Stable-dep-of: 8448828216 ("Revert "nvme: make keep-alive synchronous operation"")
Signed-off-by: Sasha Levin <sashal@kernel.org>
