Pull phy updates from Vinod Koul:
"As usual featuring couple of new driver and bunch of new device
support and some driver changes to Freescale, rockchip driver along
with couple of yaml binding conversions.
New Support:
- Qualcomm IPQ5424 qusb2 support, IPQ5018 uniphy-pcie driver
- Rockchip usb2 support for RK3562, RK3036 usb2 phy support
- Samsung exynos2200 eusb2 phy support and driver refactoring for
this support, exynos7870 USBDRD support
- Mediatek MT7988 xs-phy support
- Broadcom BCM74110 usb phy support
- Renesas RZ/V2H(P) usb2 phy support
Updates:
- Freescale phy rate claculation updates, i.MX95 tuning support
- Better error handling for amlogic pcie phy
- Rockchip color depth configuration and management support
- Yaml binding conversion for RK3399 Type-C and PCIe Phy"
* tag 'phy-for-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (77 commits)
phy: tegra: p2u: Broaden architecture dependency
phy: rockchip: inno-usb2: Add usb2 phy support for rk3562
dt-bindings: phy: rockchip,inno-usb2phy: add rk3562
phy: rockchip: inno-usb2: add phy definition for rk3036
dt-bindings: phy: rockchip,inno-usb2phy: add rk3036 compatible
phy: freescale: fsl-samsung-hdmi: Improve LUT search for best clock
phy: freescale: fsl-samsung-hdmi: Refactor finding PHY settings
phy: freescale: fsl-samsung-hdmi: Rename phy_clk_round_rate
phy: renesas: phy-rcar-gen3-usb2: Add USB2.0 PHY support for RZ/V2H(P)
phy: renesas: phy-rcar-gen3-usb2: Sort compatible entries by SoC part number
dt-bindings: phy: renesas,usb2-phy: Document RZ/V2H(P) SoC
dt-bindings: phy: renesas,usb2-phy: Add clock constraint for RZ/G2L family
phy: exynos5-usbdrd: support Exynos USBDRD 3.2 4nm controller
phy: phy-snps-eusb2: add support for exynos2200
phy: phy-snps-eusb2: refactor reference clock init
phy: phy-snps-eusb2: make reset control optional
phy: phy-snps-eusb2: make repeater optional
phy: phy-snps-eusb2: split phy init code
phy: phy-snps-eusb2: refactor constructs names
phy: move phy-qcom-snps-eusb2 out of its vendor sub-directory
...
The usb2phy on rk3036 is very similar to rk3128 but not 100% identical.
While most registers and bits are the same, a small fraction did get moved
around.
So we can re-use the phy-tuning function, but need a new set a bits.
The biggest change might be that the phy on rk3036 does not support the
charger detection, that rk3128 (and newer phys) have.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250503201512.991277-3-heiko@sntech.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When using HDMI PLL frequency division coefficient at 50.25MHz
that is calculated by rk_hdptx_phy_clk_pll_calc(), it fails to
get PHY LANE lock. Although the calculated values are within the
allowable range of PHY PLL configuration.
In order to fix the PHY LANE lock error and provide the expected
50.25MHz output, manually compute the required PHY PLL frequency
division coefficient and add it to ropll_tmds_cfg configuration
table.
Signed-off-by: Algea Cao <algea.cao@rock-chips.com>
Reviewed-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250427095124.3354439-1-algea.cao@rock-chips.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Although, in theory, the clock provider functionality could be enabled
as a standalone driver feature, in practice it is unlikely that it would
be ever needed separately from the common PHY related features, i.e.
making use of the PHY PLL as an alternative and more accurate clock
source for display modes handling. Which means the PLL will be always
programmed according to the TMDS char rate set via the HDMI PHY
configuration API.
Currently it's possible to freely adjust the rate via the clock API as
well, that is through clk_set_rate(). Making the clock read-only is not
feasible since we need to ensure any rate update done via the PHY
configuration API has been actually programmed into the hardware before
CCF accesses it. This would be normally done during phy_ops.power_on()
or clk_ops.prepare() callbacks, but it might happen that the former gets
fired too late and the latter only once, hence we need to keep handle it
via clk_ops.set_rate() as a fallback approach.
Prevent changing the TMDS character rate via CCF by letting
rk_hdptx_phy_clk_round_rate() always return the value set via
phy_configure(). To avoid breaking existing users, i.e. RK DW HDMI QP
bridge driver, until the switch to the HDMI PHY config based approach is
completed, introduce a temporary exception to the rule, toggled via the
new ->restrict_rate_change flag, which indicates whether phy_configure()
has been called or not.
Additionally, revert any unlikely rate change that might have occurred
between the calls to ->round_rate() and ->set_rate().
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20250318-phy-sam-hdptx-bpc-v6-11-8cb1678e7663@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The current workaround to setup the TMDS character rate relies on the
unconventional usage of phy_set_bus_width().
Make use of the recently introduced HDMI PHY configuration API to
properly handle the setup. The workaround will be dropped as soon as
the switch has been completed on both ends.
Rename rk_hdptx_phy_verify_config() to rk_hdptx_phy_verify_dp_config()
and introduce the rk_hdptx_phy_verify_hdmi_config() helper to check the
HDMI parameters during phy_configure().
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20250318-phy-sam-hdptx-bpc-v6-9-8cb1678e7663@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The ropll_tmds_cfg table used to identify the configuration params for
the supported rates expects the search key, i.e. bit_rate member of
struct ropll_config, to be provided in hHz rather than Hz (1 hHz = 100
Hz). This requires multiple conversions between these units being
performed at runtime.
Improve implementation clarity and efficiency by consistently using the
Hz unit throughout driver's internal data structures and functions.
Also rename the rather misleading struct member.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250318-phy-sam-hdptx-bpc-v6-8-8cb1678e7663@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pull phy updates from Vinod Koul:
"A fairly moderate sized request for the generic phy subsystem with
some new device and driver support along with driver updates with
Samsung and Qualcomm ones being major ones.
New HW Support:
- Qualcomm X1P42100 PCIe Gen4x4, QCS615 qmp usbc, PCIe UNIPHY 28LP
driver, SM8750 QMP UFS PHY
- Rockchip rk3576 hdptx, rk3562 naneng-combo support
- Samsung MIPI D-/C-PHY driver, ExynosAutov920 ufs phy driver
Updates:
- Samsung USB3 Type-C lane orientation detection and configuration
for Google gs101
- Qualcomm support for dual lane PHY support for QCS8300 SoC"
* tag 'phy-for-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (47 commits)
phy: rockchip-naneng-combo: Support rk3562
dt-bindings: phy: rockchip: Add rk3562 naneng-combophy compatible
phy: rockchip: Add Samsung MIPI D-/C-PHY driver
dt-bindings: phy: Add Rockchip MIPI C-/D-PHY schema
phy: qcom: uniphy-28lp: add COMMON_CLK dependency
phy: rockchip: usbdp: Remove unnecessary bool conversion
phy: rockchip: usbdp: Avoid call hpd_event_trigger in dp_phy_init
phy: rockchip: usbdp: Only verify link rates/lanes/voltage when the corresponding set flags are set
phy: qcom-qmp-pcie: add dual lane PHY support for QCS8300
dt-bindings: phy: qcom,sc8280xp-qmp-pcie-phy: Document the QCS8300 QMP PCIe PHY Gen4 x2
phy: qcom-qmp-ufs: Add PHY Configuration support for sm8750
dt-bindings: phy: qcom,sc8280xp-qmp-ufs-phy: document the SM8750 QMP UFS PHY
phy: qcom: Introduce PCIe UNIPHY 28LP driver
dt-bindings: phy: qcom,uniphy-pcie: Document PCIe uniphy
phy: qcom: qmp-usbc: Add qmp configuration for QCS615
phy: freescale: imx8m-pcie: assert phy reset and perst in power off
phy: freescale: imx8m-pcie: cleanup reset logic
phy: core: Remove unused phy_pm_runtime_(allow|forbid)
dt-bindings: phy: document Allwinner A523 USB-2.0 PHY
phy: phy-rockchip-samsung-hdptx: Add support for RK3576
...
Function rk_udphy_dp_hpd_event_trigger will set vogrf let it
trigger HPD interrupt to DP by Type-C. This configuration is only
required when the DP work in Alternate Mode, and called by
typec_mux_set. In standard DP mode, such settings will prevent
the DP from receiving HPD interrupts.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Link: https://lore.kernel.org/r/20250302115257.188774-1-andyshrk@163.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
According documentation of phy_configure_opts_dp, at the configure
stage, link rates should only be verify/configure when set_rate
flag is set, the same applies to lanes and voltage.
So do it as the documentation says.
Because voltage setting depends on the lanes, link rates set
previously, so record the link rates and lanes at it's verify stage.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Link: https://lore.kernel.org/r/20250312080041.524546-1-andyshrk@163.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The PHY is based on a Samsung IP block that supports HDMI 2.1, and eDP
1.4b. RK3588 integrates the Analogix eDP 1.3 TX controller IP and the
HDMI/eDP TX Combo PHY to support eDP display.
Add basic support for RBR/HBR/HBR2 link rates, and the voltage swing and
pre-emphasis configurations of each link rate are set according to the
eDP 1.3 requirements.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250205105157.580060-5-damon.ding@rock-chips.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The phy needs to know its identity in the system (phy0 or phy1 on rk3588)
for some actions and the driver currently contains code abusing of_alias
for that.
Devicetree aliases are always optional and should not be used for core
device functionality, so instead keep a list of phys on a soc in the
of_device_data and find the phy-id by comparing against the mapped
register-base.
Fixes: c4b09c5620 ("phy: phy-rockchip-samsung-hdptx: Add clock provider support")
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20241206103401.1780416-3-heiko@sntech.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
A previous patch ensured that USB Type C connector support is enabled,
but it is still possible to build the phy driver without enabling
CONFIG_USB (host support) or CONFIG_USB_GADGET (device support), and
in that case the common helper functions are unavailable:
aarch64-linux-ld: drivers/phy/rockchip/phy-rockchip-usbdp.o: in function `rk_udphy_probe':
phy-rockchip-usbdp.c:(.text+0xe74): undefined reference to `usb_get_maximum_speed'
Select CONFIG_USB_COMMON directly here, like we do in some other phy
drivers, to make sure this is available even when actual USB support
is disabled or in a loadable module that cannot be reached from a
built-in phy driver.
Fixes: 9c79b77964 ("phy: rockchip: fix CONFIG_TYPEC dependency")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250122065249.1390081-1-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Currently, the USB port via combophy on the RK3528/RK3588 SoC is broken.
usb usb8-port1: Cannot enable. Maybe the USB cable is bad?
This is due to the combphy of RK3528/RK3588 SoC has multiple resets, but
only "phy resets" need assert and deassert, "apb resets" don't need.
So change the driver to only match the phy resets, which is also what
the vendor kernel does.
Fixes: 7160820d74 ("phy: rockchip: add naneng combo phy for RK3568")
Cc: FUKAUMI Naoki <naoki@radxa.com>
Cc: Michael Zimmermann <sigmaepsilon92@gmail.com>
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20241122073006.99309-2-amadeus@jmu.edu.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Refactor the mutex handling in the rockchip_pcie_phy_power_on() function to
improve code readability and maintainability. The goto statement has
been removed, and the mutex_unlock call is now directly within the
conditional block.
Return the result of reset_control_deassert() or regmap_read_poll_timeout()
function, with 0 indicating success and an error code indicating failure.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Link: https://lore.kernel.org/r/20241012071919.3726-6-linux.amoon@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Refactor the mutex handling in the rockchip_pcie_phy_power_off() function
to improve code readability and maintainability. The goto statement has
been removed, and the mutex_unlock call is now directly within the
conditional block.
Return the result of reset_control_assert() function, with 0 indicating
success and an error code indicating failure
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Link: https://lore.kernel.org/r/20241012071919.3726-5-linux.amoon@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use devm_clk_get_enabled() instead of devm_clk_get() to make the code
cleaner and avoid calling clk_disable_unprepare(), as this is exactly
what this function does. Use the dev_err_probe() helper to simplify
error handling during probe.
Refactor the mutex handling in the rockchip_pcie_phy_init() function
to improve code readability and maintainability. The goto statement has
been removed, and the mutex_unlock call is now directly within the
conditional block.
Return the result of reset_control_assert() function, with 0 indicating
success and an error code indicating failure
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Link: https://lore.kernel.org/r/20241012071919.3726-3-linux.amoon@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pull phy updates from Vinod Koul:
"New hardware support:
- ST STM32MP25 combophy support
- Sparx5 support for lan969x serdes and updates to driver to support
this
- NXP PTN3222 eUSB2 to USB2 redriver
- Qualcomm SAR2130P eusb2 support, QCS8300 USB DW3 and QMP USB2
support, X1E80100 QMP PCIe PHY Gen4 support, QCS615 and QCS8300 QMP
UFS PHY support and SA8775P eDP PHY support
- Rockchip rk3576 usbdp and rk3576 usb2 phy support
- Binding for Microchip ATA6561 can phy
Updates:
- Freescale driver updates from hdmi support
- Conversion of rockchip rk3228 hdmi phy binding to yaml
- Broadcom usb2-phy deprecated support dropped and USB init array
update for BCM4908
- TI USXGMII mode support in J7200
- Switch back to platform_driver::remove() subsystem update"
* tag 'phy-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (59 commits)
phy: qcom: qmp: Fix lecacy-legacy typo
phy: lan969x-serdes: add support for lan969x serdes driver
dt-bindings: phy: sparx5: document lan969x
phy: sparx5-serdes: add support for branching on chip type
phy: sparx5-serdes: add indirection layer to register macros
phy: sparx5-serdes: add function for getting the CMU index
phy: sparx5-serdes: add ops to match data
phy: sparx5-serdes: add constant for the number of CMU's
phy: sparx5-serdes: add constants to match data
phy: sparx5-serdes: add support for private match data
phy: bcm-ns-usb2: drop support for old binding variant
dt-bindings: phy: bcm-ns-usb2-phy: drop deprecated variant
dt-bindings: phy: Add QMP UFS PHY compatible for QCS8300
dt-bindings: phy: qcom: snps-eusb2: Add SAR2130P compatible
dt-bindings: phy: ti,tcan104x-can: Document Microchip ATA6561
phy: airoha: Fix REG_CSR_2L_RX{0,1}_REV0 definitions
phy: airoha: Fix REG_CSR_2L_JCPLL_SDM_HREN config in airoha_pcie_phy_init_ssc_jcpll()
phy: airoha: Fix REG_PCIE_PMA_TX_RESET config in airoha_pcie_phy_init_csr_2l()
phy: airoha: Fix REG_CSR_2L_PLL_CMN_RESERVE0 config in airoha_pcie_phy_init_clk_out()
phy: phy-rockchip-samsung-hdptx: Don't request RST_PHY/RST_ROPLL/RST_LCPLL
...
Ensure CONFIG_PHY_ROCKCHIP_SAMSUNG_HDPTX depends on CONFIG_COMMON_CLK to
fix the following link errors when compile testing some random kernel
configurations:
m68k-linux-ld: drivers/phy/rockchip/phy-rockchip-samsung-hdptx.o: in function `rk_hdptx_phy_clk_register':
drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c:1031:(.text+0x470): undefined reference to `__clk_get_name'
m68k-linux-ld: drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c:1036:(.text+0x4ba): undefined reference to `devm_clk_hw_register'
m68k-linux-ld: drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c:1040:(.text+0x4d2): undefined reference to `of_clk_hw_simple_get'
m68k-linux-ld: drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c:1040:(.text+0x4da): undefined reference to `devm_of_clk_add_hw_provider'
Fixes: c4b09c5620 ("phy: phy-rockchip-samsung-hdptx: Add clock provider support")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202409180305.53PXymZn-lkp@intel.com/
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240923-sam-hdptx-link-fix-v1-1-8d10d7456305@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/phy/ to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
While touching these files, make indention of the struct initializer
consistent in several files.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20241009065307.504930-2-u.kleine-koenig@baylibre.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
