Pull ARM SoC driver updates from Arnd Bergmann:
"As usual, there are lots of minor driver changes across SoC platforms
from NXP, Amlogic, AMD Zynq, Mediatek, Qualcomm, Apple and Samsung.
These usually add support for additional chip variations in existing
drivers, but also add features or bugfixes.
The SCMI firmware subsystem gains a unified raw userspace interface
through debugfs, which can be used for validation purposes.
Newly added drivers include:
- New power management drivers for StarFive JH7110, Allwinner D1 and
Renesas RZ/V2M
- A driver for Qualcomm battery and power supply status
- A SoC device driver for identifying Nuvoton WPCM450 chips
- A regulator coupler driver for Mediatek MT81xxv"
* tag 'soc-drivers-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
power: supply: Introduce Qualcomm PMIC GLINK power supply
soc: apple: rtkit: Do not copy the reg state structure to the stack
soc: sunxi: SUN20I_PPU should depend on PM
memory: renesas-rpc-if: Remove redundant division of dummy
soc: qcom: socinfo: Add IDs for IPQ5332 and its variant
dt-bindings: arm: qcom,ids: Add IDs for IPQ5332 and its variant
dt-bindings: power: qcom,rpmpd: add RPMH_REGULATOR_LEVEL_LOW_SVS_L1
firmware: qcom_scm: Move qcom_scm.h to include/linux/firmware/qcom/
MAINTAINERS: Update qcom CPR maintainer entry
dt-bindings: firmware: document Qualcomm SM8550 SCM
dt-bindings: firmware: qcom,scm: add qcom,scm-sa8775p compatible
soc: qcom: socinfo: Add Soc IDs for IPQ8064 and variants
dt-bindings: arm: qcom,ids: Add Soc IDs for IPQ8064 and variants
soc: qcom: socinfo: Add support for new field in revision 17
soc: qcom: smd-rpm: Add IPQ9574 compatible
soc: qcom: pmic_glink: remove redundant calculation of svid
soc: qcom: stats: Populate all subsystem debugfs files
dt-bindings: soc: qcom,rpmh-rsc: Update to allow for generic nodes
soc: qcom: pmic_glink: add CONFIG_NET/CONFIG_OF dependencies
soc: qcom: pmic_glink: Introduce altmode support
...
Pull clk updates from Stephen Boyd:
"We have one small patch to the clk core this time around. It fixes a
corner case with the CLK_OPS_PARENT_ENABLE flag combined with
clk_core_is_enabled() where it hangs the system. We'll simply assume
the clk is disabled if the parent is disabled and the flag is set.
Trying to turn on the parent to check the enable state of the clk runs
into system hangs at boot. We let this bake in -next for a couple
weeks to make sure there aren't any more issues because the last
attempt to fix this ran into hangs and had to be reverted.
Note: There were some more patches to the core framework around
sync_state and disabling unused clks, but I asked for that to be
reverted from the qcom PR because it isn't ready and we're still
discussing the best solution on the list.
Outside of the core clk framework, we have the usual collection of clk
driver updates and support for new SoCs (which seems to never stop).
The dirstat is dominated by Qualcomm because they added support for
quite a few SoCs this time around and also migrated quite a few of
their drivers to clk_parent_data. The other big diff is in the
Mediatek clk drivers that saw a significant rework this cycle to
similarly modernize the code, and we'll see that work continue in the
next cycle as well. Nothing really jumps out as scary here, except
that the significant churn in parent data descriptions can have typos
that go unnoticed. More details below.
Core:
- Honor CLK_OPS_PARENT_ENABLE in clk_core_is_enabled()
New Drivers:
- Add a new clk-gpr-mux clock type and use it on i.MX6Q to add ENET
ref clocks
- Support for Mediatek MT7891 SoC clks
- Support for many Qualcomm clk controllers:
- QDU1000/QRU1000 global clock controller
- SA8775P global clock controller
- SM8550 TCSR and display clock controller
- SM6350 clock controller
- MSM8996 CBF and APCS clock controllers
Updates:
- Various cleanups and improvements to Mediatek clk drivers to reduce
code size and modernize the drivers
- Support for Versa 5P49V60 clks
- Disable R-Car H3 ES1.*, as it was only available to an internal
development group and needed a lot of quirks and workarounds
- Add PWM, Compare-Match Timer (TIM), USB, SDHI, and eMMC clocks and
resets on Renesas RZ/V2M
- Add display clocks on Renesas R-Car V4H
- Add Camera Receiving Unit (CRU) clocks and resets on Renesas RZ/G2L
- Free the imx_uart_clocks even if imx_register_uart_clocks returns
early
- Get the stdout clocks count from device tree on i.MX
- Drop the clock count argument from imx_register_uart_clocks()
- Keep the uart clocks on i.MX93 for when earlycon is used
- Fix SPDX comment in i.MX6SLL clocks bindings header
- Drop some unnecessary spaces from i.MX8ULP clocks bindings header
- Add imx_obtain_fixed_of_clock() for allowing to add a clock that is
not configured via devicetree
- Fix the ENET1 gate configuration for i.MX6UL according to the
reference manual
- Add ENET refclock mux support for i.MX6UL
- Add support for USB host/device configuration on Renesas RZ/N1
- Add PLL2 programming support, and CAN-FD clocks on Renesas R-Car
V4H
- Add D1 CAN bus gates and resets for Allwinner
- Mark D1 CPUX clock as critical on Allwinner
- Reuse D1 driver for Allwinner R528/T113
- Cleanup sunxi-ng Kconfig
- Fix sunxi-ng kernel-doc issues
- Model Allwinner H3/H5 DRAM clock as fixed clock
- Use .determine_rate() instead of .round_rate() for the dualdiv,
mpll, sclk-div and cpu-dyn-div amlogic clock drivers
- DDR clocks were marked as critical in the proper clock driver for
each AT91 SoC such that drivers/memory/atmel-sdramc.c to be deleted
in the next releases as it only does clock enablement
- Patch to avoid compiling dt-compat.o for all AT91 SoCs as only some
of them may use it
- Support synchronous power_off requests in the qcom GDSC driver for
proper GPU power collapse
- Drop test clocks from various Qualcomm clk drivers
- Update parent references to use clk_parent_data/clk_hw in various
Qualcomm clk drivers
- Fixes for the Qualcomm MSM8996 CPU clock controller
- Transition Qualcomm MSM8974 GCC off the externally defined
sleep_clk
- Add GDSCs in the global clock controller for Qualcomm QCS404
- The SDCC core clocks on Qualcomm SM6115 are moved to floor_ops
- Programming of clk_dis_wait for GPU CX GDSC on Qualcomm SC7180 and
SDM845 are moved to use the recently introduced properties in the
GDSC struct
- Qualcomm's RPMh clock driver gains SM8550 and SA8775P clocks, and
the IPA clock is added on a variety of platforms
- De-duplicate identical clks in Qualcomm SMD RPM clk driver
- Add a few missing clocks across msm8998, msm8992, msm8916, qcs404
to Qualcomm SDM RPM clk driver
- Various Qualcomm clk drivers use devm_pm_runtime_enable() to
simplify"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (228 commits)
clk: qcom: apcs-msm8986: Include bitfield.h for FIELD_PREP
clk: qcom: Revert sync_state based clk_disable_unused
clk: imx: pll14xx: fix recalc_rate for negative kdiv
clk: rs9: Drop unused pin_xin field
MAINTAINERS: clk: imx: Add Peng Fan as reviewer
clk: sprd: Add dependency for SPRD_UMS512_CLK
clk: ralink: fix 'mt7621_gate_is_enabled()' function
clk: mediatek: clk-mtk: Remove unneeded semicolon
dt-bindings: clock: remove stih416 bindings
dt-bindings: clock: add loongson-2 clock
dt-bindings: clock: add loongson-2 clock include file
clk: imx: fix compile testing imxrt1050
clk: Honor CLK_OPS_PARENT_ENABLE in clk_core_is_enabled()
clk: imx: set imx_clk_gpr_mux_ops storage-class-specifier to static
clk: renesas: rcar-gen3: Disable R-Car H3 ES1.*
dt-bindings: clock: Merge qcom,gpucc-sm8350 into qcom,gpucc.yaml
clk: qcom: gpucc-sdm845: fix clk_dis_wait being programmed for CX GDSC
clk: qcom: gpucc-sc7180: fix clk_dis_wait being programmed for CX GDSC
dt-bindings: clock: qcom,sa8775p-gcc: add the power-domains property
clk: qcom: cpu-8996: add missing cputype include
...
Pull tty / serial driver updates from Greg KH:
"Here is the big set of serial and tty driver updates for 6.3-rc1.
Once again, Jiri and Ilpo have done a number of core vt and tty/serial
layer cleanups that were much needed and appreciated. Other than that,
it's just a bunch of little tty/serial driver updates:
- qcom-geni-serial driver updates
- liteuart driver updates
- hvcs driver cleanups
- n_gsm updates and additions for new features
- more 8250 device support added
- fpga/dfl update and additions
- imx serial driver updates
- fsl_lpuart updates
- other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (143 commits)
tty: n_gsm: add keep alive support
serial: imx: remove a redundant check
dt-bindings: serial: snps-dw-apb-uart: add dma & dma-names properties
soc: qcom: geni-se: Move qcom-geni-se.h to linux/soc/qcom/geni-se.h
tty: n_gsm: add TIOCMIWAIT support
tty: n_gsm: add RING/CD control support
tty: n_gsm: mark unusable ioctl structure fields accordingly
serial: imx: get rid of registers shadowing
serial: imx: refine local variables in rxint()
serial: imx: stop using USR2 in FIFO reading loop
serial: imx: remove redundant USR2 read from FIFO reading loop
serial: imx: do not break from FIFO reading loop prematurely
serial: imx: do not sysrq broken chars
serial: imx: work-around for hardware RX flood
serial: imx: factor-out common code to imx_uart_soft_reset()
serial: 8250_pci1xxxx: Add power management functions to quad-uart driver
serial: 8250_pci1xxxx: Add RS485 support to quad-uart driver
serial: 8250_pci1xxxx: Add driver for quad-uart support
serial: 8250_pci: Add serial8250_pci_setup_port definition in 8250_pcilib.c
tty: pcn_uart: fix memory leak with using debugfs_lookup()
...
Pull networking updates from Jakub Kicinski:
"Core:
- Add dedicated kmem_cache for typical/small skb->head, avoid having
to access struct page at kfree time, and improve memory use.
- Introduce sysctl to set default RPS configuration for new netdevs.
- Define Netlink protocol specification format which can be used to
describe messages used by each family and auto-generate parsers.
Add tools for generating kernel data structures and uAPI headers.
- Expose all net/core sysctls inside netns.
- Remove 4s sleep in netpoll if carrier is instantly detected on
boot.
- Add configurable limit of MDB entries per port, and port-vlan.
- Continue populating drop reasons throughout the stack.
- Retire a handful of legacy Qdiscs and classifiers.
Protocols:
- Support IPv4 big TCP (TSO frames larger than 64kB).
- Add IP_LOCAL_PORT_RANGE socket option, to control local port range
on socket by socket basis.
- Track and report in procfs number of MPTCP sockets used.
- Support mixing IPv4 and IPv6 flows in the in-kernel MPTCP path
manager.
- IPv6: don't check net.ipv6.route.max_size and rely on garbage
collection to free memory (similarly to IPv4).
- Support Penultimate Segment Pop (PSP) flavor in SRv6 (RFC8986).
- ICMP: add per-rate limit counters.
- Add support for user scanning requests in ieee802154.
- Remove static WEP support.
- Support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate
reporting.
- WiFi 7 EHT channel puncturing support (client & AP).
BPF:
- Add a rbtree data structure following the "next-gen data structure"
precedent set by recently added linked list, that is, by using
kfunc + kptr instead of adding a new BPF map type.
- Expose XDP hints via kfuncs with initial support for RX hash and
timestamp metadata.
- Add BPF_F_NO_TUNNEL_KEY extension to bpf_skb_set_tunnel_key to
better support decap on GRE tunnel devices not operating in collect
metadata.
- Improve x86 JIT's codegen for PROBE_MEM runtime error checks.
- Remove the need for trace_printk_lock for bpf_trace_printk and
bpf_trace_vprintk helpers.
- Extend libbpf's bpf_tracing.h support for tracing arguments of
kprobes/uprobes and syscall as a special case.
- Significantly reduce the search time for module symbols by
livepatch and BPF.
- Enable cpumasks to be used as kptrs, which is useful for tracing
programs tracking which tasks end up running on which CPUs in
different time intervals.
- Add support for BPF trampoline on s390x and riscv64.
- Add capability to export the XDP features supported by the NIC.
- Add __bpf_kfunc tag for marking kernel functions as kfuncs.
- Add cgroup.memory=nobpf kernel parameter option to disable BPF
memory accounting for container environments.
Netfilter:
- Remove the CLUSTERIP target. It has been marked as obsolete for
years, and we still have WARN splats wrt races of the out-of-band
/proc interface installed by this target.
- Add 'destroy' commands to nf_tables. They are identical to the
existing 'delete' commands, but do not return an error if the
referenced object (set, chain, rule...) did not exist.
Driver API:
- Improve cpumask_local_spread() locality to help NICs set the right
IRQ affinity on AMD platforms.
- Separate C22 and C45 MDIO bus transactions more clearly.
- Introduce new DCB table to control DSCP rewrite on egress.
- Support configuration of Physical Layer Collision Avoidance (PLCA)
Reconciliation Sublayer (RS) (802.3cg-2019). Modern version of
shared medium Ethernet.
- Support for MAC Merge layer (IEEE 802.3-2018 clause 99). Allowing
preemption of low priority frames by high priority frames.
- Add support for controlling MACSec offload using netlink SET.
- Rework devlink instance refcounts to allow registration and
de-registration under the instance lock. Split the code into
multiple files, drop some of the unnecessarily granular locks and
factor out common parts of netlink operation handling.
- Add TX frame aggregation parameters (for USB drivers).
- Add a new attr TCA_EXT_WARN_MSG to report TC (offload) warning
messages with notifications for debug.
- Allow offloading of UDP NEW connections via act_ct.
- Add support for per action HW stats in TC.
- Support hardware miss to TC action (continue processing in SW from
a specific point in the action chain).
- Warn if old Wireless Extension user space interface is used with
modern cfg80211/mac80211 drivers. Do not support Wireless
Extensions for Wi-Fi 7 devices at all. Everyone should switch to
using nl80211 interface instead.
- Improve the CAN bit timing configuration. Use extack to return
error messages directly to user space, update the SJW handling,
including the definition of a new default value that will benefit
CAN-FD controllers, by increasing their oscillator tolerance.
New hardware / drivers:
- Ethernet:
- nVidia BlueField-3 support (control traffic driver)
- Ethernet support for imx93 SoCs
- Motorcomm yt8531 gigabit Ethernet PHY
- onsemi NCN26000 10BASE-T1S PHY (with support for PLCA)
- Microchip LAN8841 PHY (incl. cable diagnostics and PTP)
- Amlogic gxl MDIO mux
- WiFi:
- RealTek RTL8188EU (rtl8xxxu)
- Qualcomm Wi-Fi 7 devices (ath12k)
- CAN:
- Renesas R-Car V4H
Drivers:
- Bluetooth:
- Set Per Platform Antenna Gain (PPAG) for Intel controllers.
- Ethernet NICs:
- Intel (1G, igc):
- support TSN / Qbv / packet scheduling features of i226 model
- Intel (100G, ice):
- use GNSS subsystem instead of TTY
- multi-buffer XDP support
- extend support for GPIO pins to E823 devices
- nVidia/Mellanox:
- update the shared buffer configuration on PFC commands
- implement PTP adjphase function for HW offset control
- TC support for Geneve and GRE with VF tunnel offload
- more efficient crypto key management method
- multi-port eswitch support
- Netronome/Corigine:
- add DCB IEEE support
- support IPsec offloading for NFP3800
- Freescale/NXP (enetc):
- support XDP_REDIRECT for XDP non-linear buffers
- improve reconfig, avoid link flap and waiting for idle
- support MAC Merge layer
- Other NICs:
- sfc/ef100: add basic devlink support for ef100
- ionic: rx_push mode operation (writing descriptors via MMIO)
- bnxt: use the auxiliary bus abstraction for RDMA
- r8169: disable ASPM and reset bus in case of tx timeout
- cpsw: support QSGMII mode for J721e CPSW9G
- cpts: support pulse-per-second output
- ngbe: add an mdio bus driver
- usbnet: optimize usbnet_bh() by avoiding unnecessary queuing
- r8152: handle devices with FW with NCM support
- amd-xgbe: support 10Mbps, 2.5GbE speeds and rx-adaptation
- virtio-net: support multi buffer XDP
- virtio/vsock: replace virtio_vsock_pkt with sk_buff
- tsnep: XDP support
- Ethernet high-speed switches:
- nVidia/Mellanox (mlxsw):
- add support for latency TLV (in FW control messages)
- Microchip (sparx5):
- separate explicit and implicit traffic forwarding rules, make
the implicit rules always active
- add support for egress DSCP rewrite
- IS0 VCAP support (Ingress Classification)
- IS2 VCAP filters (protos, L3 addrs, L4 ports, flags, ToS
etc.)
- ES2 VCAP support (Egress Access Control)
- support for Per-Stream Filtering and Policing (802.1Q,
8.6.5.1)
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- add MAB (port auth) offload support
- enable PTP receive for mv88e6390
- NXP (ocelot):
- support MAC Merge layer
- support for the the vsc7512 internal copper phys
- Microchip:
- lan9303: convert to PHYLINK
- lan966x: support TC flower filter statistics
- lan937x: PTP support for KSZ9563/KSZ8563 and LAN937x
- lan937x: support Credit Based Shaper configuration
- ksz9477: support Energy Efficient Ethernet
- other:
- qca8k: convert to regmap read/write API, use bulk operations
- rswitch: Improve TX timestamp accuracy
- Intel WiFi (iwlwifi):
- EHT (Wi-Fi 7) rate reporting
- STEP equalizer support: transfer some STEP (connection to radio
on platforms with integrated wifi) related parameters from the
BIOS to the firmware.
- Qualcomm 802.11ax WiFi (ath11k):
- IPQ5018 support
- Fine Timing Measurement (FTM) responder role support
- channel 177 support
- MediaTek WiFi (mt76):
- per-PHY LED support
- mt7996: EHT (Wi-Fi 7) support
- Wireless Ethernet Dispatch (WED) reset support
- switch to using page pool allocator
- RealTek WiFi (rtw89):
- support new version of Bluetooth co-existance
- Mobile:
- rmnet: support TX aggregation"
* tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1872 commits)
page_pool: add a comment explaining the fragment counter usage
net: ethtool: fix __ethtool_dev_mm_supported() implementation
ethtool: pse-pd: Fix double word in comments
xsk: add linux/vmalloc.h to xsk.c
sefltests: netdevsim: wait for devlink instance after netns removal
selftest: fib_tests: Always cleanup before exit
net/mlx5e: Align IPsec ASO result memory to be as required by hardware
net/mlx5e: TC, Set CT miss to the specific ct action instance
net/mlx5e: Rename CHAIN_TO_REG to MAPPED_OBJ_TO_REG
net/mlx5: Refactor tc miss handling to a single function
net/mlx5: Kconfig: Make tc offload depend on tc skb extension
net/sched: flower: Support hardware miss to tc action
net/sched: flower: Move filter handle initialization earlier
net/sched: cls_api: Support hardware miss to tc action
net/sched: Rename user cookie and act cookie
sfc: fix builds without CONFIG_RTC_LIB
sfc: clean up some inconsistent indentings
net/mlx4_en: Introduce flexible array to silence overflow warning
net: lan966x: Fix possible deadlock inside PTP
net/ulp: Remove redundant ->clone() test in inet_clone_ulp().
...
More Qualcomm driver updates for 6.3
The qcom_scm.h file is moved into firmware/qcom, to avoid having any
Qualcomm-specific files directly in include/linux.
Support for PMIC GLINK is introduced, which on newer Qualcomm platforms
provides an interface to the firmware implementing battery management
and USB Type-C handling. Together with the base driver comes the custom
altmode support driver.
SMD RPM gains support for IPQ9574, and socinfo is extended with support
for revision 17 of the information format and soc_id for IPQ5332 and
IPQ8064 are added.
The qcom_stats is changes not to fail when not all parts are
initialized.
* tag 'qcom-drivers-for-6.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
soc: qcom: socinfo: Add IDs for IPQ5332 and its variant
dt-bindings: arm: qcom,ids: Add IDs for IPQ5332 and its variant
dt-bindings: power: qcom,rpmpd: add RPMH_REGULATOR_LEVEL_LOW_SVS_L1
firmware: qcom_scm: Move qcom_scm.h to include/linux/firmware/qcom/
MAINTAINERS: Update qcom CPR maintainer entry
dt-bindings: firmware: document Qualcomm SM8550 SCM
dt-bindings: firmware: qcom,scm: add qcom,scm-sa8775p compatible
soc: qcom: socinfo: Add Soc IDs for IPQ8064 and variants
dt-bindings: arm: qcom,ids: Add Soc IDs for IPQ8064 and variants
soc: qcom: socinfo: Add support for new field in revision 17
soc: qcom: smd-rpm: Add IPQ9574 compatible
soc: qcom: pmic_glink: remove redundant calculation of svid
soc: qcom: stats: Populate all subsystem debugfs files
dt-bindings: soc: qcom,rpmh-rsc: Update to allow for generic nodes
soc: qcom: pmic_glink: add CONFIG_NET/CONFIG_OF dependencies
soc: qcom: pmic_glink: Introduce altmode support
soc: qcom: pmic_glink: Introduce base PMIC GLINK driver
dt-bindings: soc: qcom: Introduce PMIC GLINK binding
soc: qcom: dcc: Drop driver for now
Link: https://lore.kernel.org/r/20230210182242.2023901-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Qualcomm driver updates for v6.3
This introduces a new driver for the Data Capture and Compare block,
which provides a mechanism for capturing hardware state (access MMIO
registers) either upon request of triggered automatically e.g. upon a
watchdog bite, for post mortem analysis.
The remote filesystem memory share driver gains support for having its
memory bound to more than a single VMID.
The SCM driver gains the minimal support needed to support a new
mechanism where secure world can put calls on hold and later request
them to be retried.
Support for the new SA8775P platform is added to rpmhpd, QDU1000 is
added to the SCM driver and a long list of platforms are added to the
socinfo driver. Support for socinfo data revision 16 is also introduced.
Lastly a driver to program the ramp controller in MSM8976 is introduced.
* tag 'qcom-drivers-for-6.3' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (33 commits)
firmware: qcom: scm: Add wait-queue handling logic
dt-bindings: firmware: qcom,scm: Add optional interrupt
Revert "dt-bindings: power: rpmpd: Add SM4250 support"
Revert "soc: qcom: rpmpd: Add SM4250 support"
soc: qcom: socinfo: Add a bunch of older SoCs
dt-bindings: arm: qcom,ids: Add a bunch of older SoCs
dt-bindings: arm: qcom,ids: Add QRD board ID
soc: qcom: socinfo: Fix soc_id order
dt-bindings: soc: qcom: smd-rpm: Exclude MSM8936 from glink-channels
dt-bindings: firmware: qcom: scm: Separate VMIDs from header to bindings
soc: qcom: rmtfs: Optionally map RMTFS to more VMs
dt-bindings: reserved-memory: rmtfs: Make qcom,vmid an array
dt-bindings: firmware: scm: Add QDU1000/QRU1000 compatible
dt-bindings: firmware: qcom,scm: narrow clocks and interconnects
dt-bindings: firmware: qcom,scm: document MSM8226 clocks
soc: qcom: ramp_controller: Make things static
soc: qcom: rmphpd: add power domains for sa8775p
dt-bindings: power: qcom,rpmpd: document sa8775p
PM: AVS: qcom-cpr: Fix an error handling path in cpr_probe()
soc: qcom: dcc: rewrite description of dcc sysfs files
...
Link: https://lore.kernel.org/r/20230126163008.3676950-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Apple SoC RTKit/PMGR updates for 6.3.
This time around we have a PMGR change to allow IRQ-safe usage, RTKit
crash register dump decoding, and a bunch of RTKit API changes used by
upcoming drivers.
* tag 'asahi-soc-rtkit-pmgr-6.3' of https://github.com/AsahiLinux/linux:
soc: apple: rtkit: Add register dump decoding to crashlog
soc: apple: rtkit: Export non-devm init/free functions
soc: apple: rtkit: Add a private pointer to apple_rtkit_shmem
soc: apple: apple-pmgr-pwrstate: Switch to IRQ-safe mode
soc: apple: rtkit: Add apple_rtkit_idle() function
Link: https://lore.kernel.org/r/4790bdc4-b6e2-228b-771f-023363f65fb3@marcan.st
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The PMIC GLINK service runs on one of the co-processors of some modern
Qualcomm platforms and implements USB-C and battery managements. It uses
a message based protocol over GLINK for communication with the OS, hence
the name.
The driver implemented provides the rpmsg device for communication and
uses auxiliary bus to spawn off individual devices in respective
subsystem. The auxiliary devices are spawned off from a
platform_device, so that the drm_bridge is available early, to allow the
DisplayPort driver to probe even before the remoteproc has spun up.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Konrad Dybcio <konrad.dybcio@linaro.org> # SM8350 PDX215
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-MTP & SM8450-HDK
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230201041853.1934355-3-quic_bjorande@quicinc.com
The s3c-cpu-freq header was previously included by:
./arch/arm/mach-s3c/mach-bast.c
./arch/arm/mach-s3c/mach-osiris-dvs.c
./arch/arm/mach-s3c/mach-osiris.c
./include/linux/soc/samsung/s3c-cpufreq-core.h
Commit a4946a153cb9 ("ARM: s3c: remove all s3c24xx support") removes the
files in ./arch/arm/mach-s3c/; commit daf0ee583fc7 ("cpufreq: remove
s3c24xx drivers") removes the file s3c-cpufreq-core.h.
Remove this obsolete header file.
This issue was identified, as s3c-cpu-freq.h referred to the removed config
ARM_S3C_CPUFREQ.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
While we normally encourage devm usage by drivers, some consumers (and
in particular the upcoming Rust abstractions) might want to manually
manage memory. Export the raw functions to make this possible.
Signed-off-by: Asahi Lina <lina@asahilina.net>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Eric Curtin <ecurtin@redhat.com>
Signed-off-by: Hector Martin <marcan@marcan.st>
This allows downstream consumers to keep track of private data for shmem
mappings. In particular, the Rust abstraction will use this to safely
drop data associated with a mapping when it is unmapped.
Signed-off-by: Asahi Lina <lina@asahilina.net>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Eric Curtin <ecurtin@redhat.com>
Signed-off-by: Hector Martin <marcan@marcan.st>
Add cmdq support for mtk-mmsys config API.
The mmsys config register settings need to take effect with the other
HW settings(like OVL_ADAPTOR...) at the same vblanking time.
If we use CPU to write the mmsys reg, we can't guarantee all the
settings can be written in the same vblanking time.
Cmdq is used for this purpose. We prepare all the related HW settings
in one cmdq packet. The first command in the packet is "wait stream done",
and then following with all the HW settings. After the cmdq packet is
flush to GCE HW. The GCE waits for the "stream done event" to coming
and then starts flushing all the HW settings. This can guarantee all
the settings flush in the same vblanking.
Signed-off-by: Nancy.Lin <nancy.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Link: https://lore.kernel.org/r/20230113104434.28023-8-nancy.lin@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Kalle Valo says:
====================
wireless-next patches for v6.3
First set of patches for v6.3. The most important change here is that
the old Wireless Extension user space interface is not supported on
Wi-Fi 7 devices at all. We also added a warning if anyone with modern
drivers (ie. cfg80211 and mac80211 drivers) tries to use Wireless
Extensions, everyone should switch to using nl80211 interface instead.
Static WEP support is removed, there wasn't any driver using that
anyway so there's no user impact. Otherwise it's smaller features and
fixes as usual.
Note: As mt76 had tricky conflicts due to the fixes in wireless tree,
we decided to merge wireless into wireless-next to solve them easily.
There should not be any merge problems anymore.
Major changes:
cfg80211
- remove never used static WEP support
- warn if Wireless Extention interface is used with cfg80211/mac80211 drivers
- stop supporting Wireless Extensions with Wi-Fi 7 devices
- support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate reporting
rfkill
- add GPIO DT support
bitfield
- add FIELD_PREP_CONST()
mt76
- per-PHY LED support
rtw89
- support new Bluetooth co-existance version
rtl8xxxu
- support RTL8188EU
* tag 'wireless-next-2023-01-23' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (123 commits)
wifi: wireless: deny wireless extensions on MLO-capable devices
wifi: wireless: warn on most wireless extension usage
wifi: mac80211: drop extra 'e' from ieeee80211... name
wifi: cfg80211: Deduplicate certificate loading
bitfield: add FIELD_PREP_CONST()
wifi: mac80211: add kernel-doc for EHT structure
mac80211: support minimal EHT rate reporting on RX
wifi: mac80211: Add HE MU-MIMO related flags in ieee80211_bss_conf
wifi: mac80211: Add VHT MU-MIMO related flags in ieee80211_bss_conf
wifi: cfg80211: Use MLD address to indicate MLD STA disconnection
wifi: cfg80211: Support 32 bytes KCK key in GTK rekey offload
wifi: cfg80211: Fix extended KCK key length check in nl80211_set_rekey_data()
wifi: cfg80211: remove support for static WEP
wifi: rtl8xxxu: Dump the efuse only for untested devices
wifi: rtl8xxxu: Print the ROM version too
wifi: rtw88: Use non-atomic sta iterator in rtw_ra_mask_info_update()
wifi: rtw88: Use rtw_iterate_vifs() for rtw_vif_watch_dog_iter()
wifi: rtw88: Move register access from rtw_bf_assoc() outside the RCU
wifi: rtl8xxxu: Use a longer retry limit of 48
wifi: rtl8xxxu: Report the RSSI to the firmware
...
====================
Link: https://lore.kernel.org/r/20230123103338.330CBC433EF@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Due to the two cherry picked commits from wireless to wireless-next we have
several conflicts in mt76. To avoid any bugs with conflicts merge wireless into
wireless-next.
96f134dc19 wifi: mt76: handle possible mt76_rx_token_consume failures
fe13dad899 wifi: mt76: dma: do not increment queue head if mt76_dma_add_buf fails
This driver could not be enabled on s3c64xx for a long time
because of the ARCH_MULTIPLATFORM dependency, so remove it.
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Assuming that we don't actually want the old-style pm-mmp2.c
and pm-pxa910.c implementation, all these files can go away
as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
After the removal of the unused board files, I went through the
omap1 code to look for code that no longer has any callers
and remove that.
In particular, support for the omap7xx/omap8xx family is now
completely unused, so I'm only leaving omap15xx/omap16xx/omap59xx.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: linux-omap@vger.kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
While compile-testing randconfig builds for the upcoming boardfile
removal, I noticed that an earlier patch of mine was completely
broken, and the introduction of CONFIG_ARCH_OMAP1_ANY only replaced
one set of build failures with another one, now resulting in
link failures like
ld: drivers/video/fbdev/omap/omapfb_main.o: in function `omapfb_do_probe':
drivers/video/fbdev/omap/omapfb_main.c:1703: undefined reference to `omap_set_dma_priority'
ld: drivers/dma/ti/omap-dma.o: in function `omap_dma_free_chan_resources':
drivers/dma/ti/omap-dma.c:777: undefined reference to `omap_free_dma'
drivers/dma/ti/omap-dma.c:1685: undefined reference to `omap_get_plat_info'
ld: drivers/usb/gadget/udc/omap_udc.o: in function `next_in_dma':
drivers/usb/gadget/udc/omap_udc.c:820: undefined reference to `omap_get_dma_active_status'
I tried reworking it, but the resulting patch ended up much bigger than
simply avoiding the original problem of unused-function warnings like
arch/arm/mach-omap1/mcbsp.c:76:30: error: unused variable 'omap1_mcbsp_ops' [-Werror,-Wunused-variable]
As a result, revert the previous fix, and rearrange the code that
produces warnings to hide them. For mcbsp, the #ifdef check can
simply be removed as the cpu_is_omapxxx() checks already achieve
the same result, while in the io.c the easiest solution appears to
be to merge the common map bits into each soc specific portion.
This gets cleaned in a nicer way after omap7xx support gets dropped,
as the remaining SoCs all have the exact same I/O map.
Fixes: 615dce5bf7 ("ARM: omap1: fix build with no SoC selected")
Cc: stable@vger.kernel.org
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull networking updates from Paolo Abeni:
"Core:
- Allow live renaming when an interface is up
- Add retpoline wrappers for tc, improving considerably the
performances of complex queue discipline configurations
- Add inet drop monitor support
- A few GRO performance improvements
- Add infrastructure for atomic dev stats, addressing long standing
data races
- De-duplicate common code between OVS and conntrack offloading
infrastructure
- A bunch of UBSAN_BOUNDS/FORTIFY_SOURCE improvements
- Netfilter: introduce packet parser for tunneled packets
- Replace IPVS timer-based estimators with kthreads to scale up the
workload with the number of available CPUs
- Add the helper support for connection-tracking OVS offload
BPF:
- Support for user defined BPF objects: the use case is to allocate
own objects, build own object hierarchies and use the building
blocks to build own data structures flexibly, for example, linked
lists in BPF
- Make cgroup local storage available to non-cgroup attached BPF
programs
- Avoid unnecessary deadlock detection and failures wrt BPF task
storage helpers
- A relevant bunch of BPF verifier fixes and improvements
- Veristat tool improvements to support custom filtering, sorting,
and replay of results
- Add LLVM disassembler as default library for dumping JITed code
- Lots of new BPF documentation for various BPF maps
- Add bpf_rcu_read_{,un}lock() support for sleepable programs
- Add RCU grace period chaining to BPF to wait for the completion of
access from both sleepable and non-sleepable BPF programs
- Add support storing struct task_struct objects as kptrs in maps
- Improve helper UAPI by explicitly defining BPF_FUNC_xxx integer
values
- Add libbpf *_opts API-variants for bpf_*_get_fd_by_id() functions
Protocols:
- TCP: implement Protective Load Balancing across switch links
- TCP: allow dynamically disabling TCP-MD5 static key, reverting back
to fast[er]-path
- UDP: Introduce optional per-netns hash lookup table
- IPv6: simplify and cleanup sockets disposal
- Netlink: support different type policies for each generic netlink
operation
- MPTCP: add MSG_FASTOPEN and FastOpen listener side support
- MPTCP: add netlink notification support for listener sockets events
- SCTP: add VRF support, allowing sctp sockets binding to VRF devices
- Add bridging MAC Authentication Bypass (MAB) support
- Extensions for Ethernet VPN bridging implementation to better
support multicast scenarios
- More work for Wi-Fi 7 support, comprising conversion of all the
existing drivers to internal TX queue usage
- IPSec: introduce a new offload type (packet offload) allowing
complete header processing and crypto offloading
- IPSec: extended ack support for more descriptive XFRM error
reporting
- RXRPC: increase SACK table size and move processing into a
per-local endpoint kernel thread, reducing considerably the
required locking
- IEEE 802154: synchronous send frame and extended filtering support,
initial support for scanning available 15.4 networks
- Tun: bump the link speed from 10Mbps to 10Gbps
- Tun/VirtioNet: implement UDP segmentation offload support
Driver API:
- PHY/SFP: improve power level switching between standard level 1 and
the higher power levels
- New API for netdev <-> devlink_port linkage
- PTP: convert existing drivers to new frequency adjustment
implementation
- DSA: add support for rx offloading
- Autoload DSA tagging driver when dynamically changing protocol
- Add new PCP and APPTRUST attributes to Data Center Bridging
- Add configuration support for 800Gbps link speed
- Add devlink port function attribute to enable/disable RoCE and
migratable
- Extend devlink-rate to support strict prioriry and weighted fair
queuing
- Add devlink support to directly reading from region memory
- New device tree helper to fetch MAC address from nvmem
- New big TCP helper to simplify temporary header stripping
New hardware / drivers:
- Ethernet:
- Marvel Octeon CNF95N and CN10KB Ethernet Switches
- Marvel Prestera AC5X Ethernet Switch
- WangXun 10 Gigabit NIC
- Motorcomm yt8521 Gigabit Ethernet
- Microchip ksz9563 Gigabit Ethernet Switch
- Microsoft Azure Network Adapter
- Linux Automation 10Base-T1L adapter
- PHY:
- Aquantia AQR112 and AQR412
- Motorcomm YT8531S
- PTP:
- Orolia ART-CARD
- WiFi:
- MediaTek Wi-Fi 7 (802.11be) devices
- RealTek rtw8821cu, rtw8822bu, rtw8822cu and rtw8723du USB
devices
- Bluetooth:
- Broadcom BCM4377/4378/4387 Bluetooth chipsets
- Realtek RTL8852BE and RTL8723DS
- Cypress.CYW4373A0 WiFi + Bluetooth combo device
Drivers:
- CAN:
- gs_usb: bus error reporting support
- kvaser_usb: listen only and bus error reporting support
- Ethernet NICs:
- Intel (100G):
- extend action skbedit to RX queue mapping
- implement devlink-rate support
- support direct read from memory
- nVidia/Mellanox (mlx5):
- SW steering improvements, increasing rules update rate
- Support for enhanced events compression
- extend H/W offload packet manipulation capabilities
- implement IPSec packet offload mode
- nVidia/Mellanox (mlx4):
- better big TCP support
- Netronome Ethernet NICs (nfp):
- IPsec offload support
- add support for multicast filter
- Broadcom:
- RSS and PTP support improvements
- AMD/SolarFlare:
- netlink extened ack improvements
- add basic flower matches to offload, and related stats
- Virtual NICs:
- ibmvnic: introduce affinity hint support
- small / embedded:
- FreeScale fec: add initial XDP support
- Marvel mv643xx_eth: support MII/GMII/RGMII modes for Kirkwood
- TI am65-cpsw: add suspend/resume support
- Mediatek MT7986: add RX wireless wthernet dispatch support
- Realtek 8169: enable GRO software interrupt coalescing per
default
- Ethernet high-speed switches:
- Microchip (sparx5):
- add support for Sparx5 TC/flower H/W offload via VCAP
- Mellanox mlxsw:
- add 802.1X and MAC Authentication Bypass offload support
- add ip6gre support
- Embedded Ethernet switches:
- Mediatek (mtk_eth_soc):
- improve PCS implementation, add DSA untag support
- enable flow offload support
- Renesas:
- add rswitch R-Car Gen4 gPTP support
- Microchip (lan966x):
- add full XDP support
- add TC H/W offload via VCAP
- enable PTP on bridge interfaces
- Microchip (ksz8):
- add MTU support for KSZ8 series
- Qualcomm 802.11ax WiFi (ath11k):
- support configuring channel dwell time during scan
- MediaTek WiFi (mt76):
- enable Wireless Ethernet Dispatch (WED) offload support
- add ack signal support
- enable coredump support
- remain_on_channel support
- Intel WiFi (iwlwifi):
- enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities
- 320 MHz channels support
- RealTek WiFi (rtw89):
- new dynamic header firmware format support
- wake-over-WLAN support"
* tag 'net-next-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2002 commits)
ipvs: fix type warning in do_div() on 32 bit
net: lan966x: Remove a useless test in lan966x_ptp_add_trap()
net: ipa: add IPA v4.7 support
dt-bindings: net: qcom,ipa: Add SM6350 compatible
bnxt: Use generic HBH removal helper in tx path
IPv6/GRO: generic helper to remove temporary HBH/jumbo header in driver
selftests: forwarding: Add bridge MDB test
selftests: forwarding: Rename bridge_mdb test
bridge: mcast: Support replacement of MDB port group entries
bridge: mcast: Allow user space to specify MDB entry routing protocol
bridge: mcast: Allow user space to add (*, G) with a source list and filter mode
bridge: mcast: Add support for (*, G) with a source list and filter mode
bridge: mcast: Avoid arming group timer when (S, G) corresponds to a source
bridge: mcast: Add a flag for user installed source entries
bridge: mcast: Expose __br_multicast_del_group_src()
bridge: mcast: Expose br_multicast_new_group_src()
bridge: mcast: Add a centralized error path
bridge: mcast: Place netlink policy before validation functions
bridge: mcast: Split (*, G) and (S, G) addition into different functions
bridge: mcast: Do not derive entry type from its filter mode
...
Pull regulator updates from Mark Brown:
"Quite a quiet release for regulator, the diffstat is dominated by the
I2C migration to probe_new() and the newly added MT6357 driver. We've
just one framework addition and the rest is all new device support,
fixes and cleanups.
The framework addition is an API for requesting all regulators defined
in DT, this isn't great practice but has reasonable applications when
there is generic code handling devices on buses where the bus
specification doesn't include power. The immediate application is MDIO
but I believe there's others, it's another API that'll need an eye
keeping on it for undesirable usage.
Summary:
- An API for requesting all regulators defined in DT
- Conversion of lots of drivers to the I2C probe_new() API
- Support for Mediatek MT6357, Qualcomm PM8550, PMR735a and Richtek
RT6190"
* tag 'regulator-v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (56 commits)
regulator: core: Use different devices for resource allocation and DT lookup
dt-bindings: Add missing 'unevaluatedProperties' to regulator nodes
regulator: qcom-labibb: Fix missing of_node_put() in qcom_labibb_regulator_probe()
regulator: add mt6357 regulator
regulator: dt-bindings: Add binding schema for mt6357 regulators
regulator: core: fix resource leak in regulator_register()
regulator: core: fix module refcount leak in set_supply()
regulator: core: fix use_count leakage when handling boot-on
regulator: rk808: Use dev_err_probe
regulator: rk808: reduce 'struct rk808' usage
regulator: Drop obsolete dependencies on COMPILE_TEST
regulator: pv88080-regulator: Convert to i2c's .probe_new()
regulator: pfuze100-regulator: Convert to i2c's .probe_new()
regulator: isl6271a-regulator: Convert to i2c's .probe_new()
regulator: fan53555: Convert to i2c's .probe_new()
regulator: act8865-regulator: Convert to i2c's .probe_new()
regulator: qcom-rpmh: Add support for PM8550 regulators
regulator: dt-bindings: qcom,rpmh: Add compatible for PM8550
regulator: tps65023-regulator: Convert to i2c's .probe_new()
regulator: tps62360-regulator: Convert to i2c's .probe_new()
...
Since wed rx_buf_ring page_frag_cache is no longer used in a hot path,
remove it and rely on page allocation APIs in
mt7915_mmio_wed_init_rx_buf() and mt7915_mmio_wed_release_rx_buf()
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
More Qualcomm driver updates for 6.2
Socinfo is extended with knowledge about MSM8956, MSM8976, SM6115,
SM4250, SM8150, SA8155 and SM8550.
Support for RSC v3, as found in SM8550 is added to the RPMH RSC driver.
Support for SM8550 and SM4250 ARC regulators are added to the RPM(h)
power-domain drivers. SM8550 support is added to the LLCC driver.
The AOSS QMP binding is declared compatible for SM8550.
BWMON and LLCC now selects REGMAP_MMIO to ensure dependencies are built
properly.
* tag 'qcom-drivers-for-6.2-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
soc: qcom: socinfo: Add SM6115 / SM4250 SoC IDs to the soc_id table
dt-bindings: arm: qcom,ids: Add SoC IDs for SM6115 / SM4250 and variants
soc: qcom: socinfo: Add SM8150 and SA8155 SoC IDs to the soc_id table
dt-bindings: arm: qcom,ids: Add SoC IDs for SM8150 and SA8155
dt-bindings: soc: qcom: apr: document generic qcom,apr compatible
soc: qcom: Select REMAP_MMIO for ICC_BWMON driver
soc: qcom: Select REMAP_MMIO for LLCC driver
soc: qcom: rpmpd: Add SM4250 support
dt-bindings: power: rpmpd: Add SM4250 support
dt-bindings: soc: qcom: aoss: Add compatible for SM8550
soc: qcom: llcc: Add configuration data for SM8550
dt-bindings: arm: msm: Add LLCC compatible for SM8550
soc: qcom: llcc: Add v4.1 HW version support
soc: qcom: socinfo: Add SM8550 ID
soc: qcom: rpmh-rsc: Avoid unnecessary checks on irq-done response
soc: qcom: rpmh-rsc: Add support for RSC v3 register offsets
soc: qcom: rpmhpd: Add SM8550 power domains
dt-bindings: power: rpmpd: Add SM8550 to rpmpd binding
soc: qcom: socinfo: Add MSM8956/76 SoC IDs to the soc_id table
dt-bindings: arm: qcom,ids: Add SoC IDs for MSM8956 and MSM8976
Link: https://lore.kernel.org/r/20221207154134.3233779-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Introduce reset parameter to mtk_wed_tx_ring_setup signature.
This is a preliminary patch to add Wireless Ethernet Dispatcher reset
support.
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Update mtk_wed_stop routine and rename old mtk_wed_stop() to
mtk_wed_deinit(). This is a preliminary patch to add Wireless Ethernet
Dispatcher reset support.
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Rename tx_wdma queue array in rx_wdma since this is rx side of wdma soc.
Moreover rename mtk_wed_wdma_ring_setup routine in
mtk_wed_wdma_rx_ring_setup()
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce WED mcu support used to configure WED WO chip.
This is a preliminary patch in order to add RX Wireless
Ethernet Dispatch available on MT7986 SoC.
Tested-by: Daniel Golle <daniel@makrotopia.org>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The difference between MT8186 and other ICs is that when modifying the
output format, we need to modify the mmsys_base+0x400 register to take
effect. So when setting the dpi output format, we need to call
mtk_mmsys_ddp_dpi_fmt_config to set it to MT8186 synchronously.
Commit a071e52f75d1 ("soc: mediatek: Add mmsys func to adapt to dpi
output for MT8186") lacked some of the possible output formats and also
had a wrong bitmask.
Add the missing output formats and fix the bitmask.
While at it, also update mtk_mmsys_ddp_dpi_fmt_config() to use generic
formats, so that it is slightly easier to extend for other platforms.
Fixes: a071e52f75d1 ("soc: mediatek: Add mmsys func to adapt to dpi output for MT8186")
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Pull clk updates from Stephen Boyd:
"We have some late breaking reports that a patch series to rework clk
rate range support broke boot on some devices, so I've left that
branch out of this. Hopefully we can get to that next week, or punt on
it and let it bake another cycle. That means we don't really have any
changes to the core framework this time around besides a few typo
fixes. Instead this is all clk driver updates and fixes.
The usual suspects are here (again), with Qualcomm dominating the
diffstat. We look to have gained support for quite a few new Qualcomm
SoCs and Dmitry worked on updating many of the existing Qualcomm
drivers to use clk_parent_data. After that we have MediaTek drivers
getting some much needed updates, in particular to support GPU DVFS.
There are also quite a few Samsung clk driver patches, but that's
mostly because there was a maintainer change and so last release we
missed some of those patches.
Overall things look normal, but I'm slowly reviewing core framework
code nowadays and that shows given the rate range patches had to be
yanked last minute. Let's hope this situation changes soon.
New Drivers:
- Support for Renesas VersaClock7 clock generator family
- Add Spreadtrum UMS512 SoC clk support
- New clock drivers for MediaTek Helio X10 MT6795
- Display clks for Qualcomm SM6115, SM8450
- GPU clks for Qualcomm SC8280XP
- Qualcomm MSM8909 and SM6375 global and SMD RPM clk drivers
Deleted Drivers:
- Remove DaVinci DM644x and DM646x clk driver support
Updates:
- Convert Baikal-T1 CCU driver to platform driver
- Split reset support out of primary Baikal-T1 CCU driver
- Add some missing clks required for RPiVid Video Decoder on
RaspberryPi
- Mark PLLC critical on bcm2835
- More devm helpers for fixed rate registration
- Various PXA168 clk driver fixes
- Add resets for MediaTek MT8195 PCIe and USB
- Miscellaneous of_node_put() fixes
- Nuke dt-bindings/clk path (again) by moving headers to
dt-bindings/clock
- Convert gpio-clk-gate binding to YAML
- Various fixes to AMD/Xilinx Zynqmp clk driver
- Graduate AMD/Xilinx "clocking wizard" driver from staging
- Add missing DPI1_HDMI clock in MT8195 VDOSYS1
- Clock driver changes to support GPU DVFS on MT8183, MT8192, MT8195
- Fix GPU clock topology on MT8195
- Propogate rate changes from GPU clock gate up the tree
- Clock mux notifiers for GPU-related PLLs
- Conversion of more "simple" drivers to mtk_clk_simple_probe()
- Hook up mtk_clk_simple_remove() for "simple" MT8192 clock drivers
- Fixes to previous |struct clk| to |struct clk_hw| conversion on
MediaTek
- Shrink MT8192 clock driver by deduplicating clock parent lists
- Change order between 'sim_enet_root_clk' and 'enet_qos_root_clk'
clocks for i.MX8MP
- Drop unnecessary newline in i.MX8MM dt-bindings
- Add more MU1 and SAI clocks dt-bindings Ids
- Introduce slice busy bit check for i.MX93 composite clock
- Introduce white list bit check for i.MX93 composite clock
- Add new i.MX93 clock gate
- Add MU1 and MU2 clocks to i.MX93 clock provider
- Add SAI IPG clocks to i.MX93 clock provider
- add generic clocks for U(S)ART available on SAMA5D2 SoCs
- reset controller support for Polarfire clocks
- .round_rate and .set rate support for clk-mpfs
- code cleanup for clk-mpfs
- PLL support for PolarFire SoC's Clock Conditioning Circuitry
- Add watchdog, I2C, pin control/GPIO, and Ethernet clocks on R-Car
V4H
- Add SDHI, Timer (CMT/TMU), and SPI (MSIOF) clocks on R-Car S4-8
- Add I2C clocks and resets on RZ/V2M
- Document clock support for the RZ/Five SoC
- mux-variant clock using the table variant to select parents
- clock controller for the rv1126 soc
- conversion of rk3128 to yaml and relicensing of the yaml bindings
to gpl2+MIT (following dt-binding guildelines)
- Exynos7885: add FSYS, TREX and MFC clock controllers
- Exynos850: add IS and AUD (audio) clock controllers with bindings
- ExynosAutov9: add FSYS clock controllers with bindings
- ExynosAutov9: correct clock IDs in bindings of Peric 0 and 1 clock
controllers, due to duplicated entries. This is an acceptable ABI
break: recently developed/added platform so without legacies, acked
by known users/developers
- ExynosAutov9: add few missing Peric 0/1 gates
- ExynosAutov9: correct register offsets of few Peric 0/1 clocks
- Minor code improvements (use of_device_get_match_data() helper,
code style)
- Add Krzysztof Kozlowski as co-maintainer of Samsung SoC clocks, as
he already maintainers that architecture/platform
- Keep Qualcomm GDSCs enabled when PWRSTS_RET flag is there, solving
retention issues during suspend of USB on Qualcomm sc7180/sc7280
and SC8280XP
- Qualcomm SM6115 and QCM2260 are moved to reuse PLL configuration
- Qualcomm SDM660 SDCC1 moved to floor clk ops
- Support for the APCS PLLs for Qualcomm IPQ8064, IPQ8074 and IPQ6018
was added/fixed
- The Qualcomm MSM8996 CPU clocks are updated with support for ACD
- Support for Qualcomm SDM670 GCC and RPMh clks was added
- Transition to parent_data, parent_hws and use of ARRAY_SIZE() for
num_parents was done for many Qualcomm SoCs
- Support for per-reset defined delay on Qualcomm was introduced"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (283 commits)
clk: qcom: gcc-sm6375: Ensure unsigned long type
clk: qcom: gcc-sm6375: Remove unused variables
clk: qcom: kpss-xcc: convert to parent data API
clk: introduce (devm_)hw_register_mux_parent_data_table API
clk: allow building lan966x as a module
clk: clk-xgene: simplify if-if to if-else
clk: ast2600: BCLK comes from EPLL
clk: clocking-wizard: Depend on HAS_IOMEM
clk: clocking-wizard: Use dev_err_probe() helper
clk: nxp: fix typo in comment
clk: pxa: add a check for the return value of kzalloc()
clk: vc5: Add support for IDT/Renesas VersaClock 5P49V6975
dt-bindings: clock: vc5: Add 5P49V6975
clk: mvebu: armada-37xx-tbg: Remove the unneeded result variable
clk: ti: dra7-atl: Fix reference leak in of_dra7_atl_clk_probe
clk: Renesas versaclock7 ccf device driver
dt-bindings: Renesas versaclock7 device tree bindings
clk: ti: Balance of_node_get() calls for of_find_node_by_name()
clk: imx: scu: fix memleak on platform_device_add() fails
clk: vc5: Use regmap_{set,clear}_bits() where appropriate
...
Pull ARM driver updates from Arnd Bergmann:
"The drivers branch for 6.1 is a bit larger than for most releases.
Most of the changes come from SoC maintainers for the drivers/soc
subsystem:
- A new driver for error handling on the NVIDIA Tegra 'control
backbone' bus.
- A new driver for Qualcomm LLCC/DDR bandwidth measurement
- New Rockchip rv1126 and rk3588 power domain drivers
- DT binding updates for memory controllers, older Rockchip SoCs,
various Mediatek devices, Qualcomm SCM firmware
- Minor updates to Hisilicon LPC bus, the Allwinner SRAM driver, the
Apple rtkit firmware driver, Tegra firmware
- Minor updates for SoC drivers (Samsung, Mediatek, Renesas, Tegra,
Qualcomm, Broadcom, NXP, ...)
There are also some separate subsystem with downstream maintainers
that merge updates this way:
- Various updates and new drivers in the memory controller subsystem
for Mediatek and Broadcom SoCs
- Small set of changes in preparation to add support for FF-A v1.1
specification later, in the Arm FF-A firmware subsystem
- debugfs support in the PSCI firmware subsystem"
* tag 'arm-drivers-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (149 commits)
ARM: remove check for CONFIG_DEBUG_LL_SER3
firmware/psci: Add debugfs support to ease debugging
firmware/psci: Print a warning if PSCI doesn't accept PC mode
dt-bindings: memory: snps,dw-umctl2-ddrc: Extend schema with IRQs/resets/clocks props
dt-bindings: memory: snps,dw-umctl2-ddrc: Replace opencoded numbers with macros
dt-bindings: memory: snps,dw-umctl2-ddrc: Use more descriptive device name
dt-bindings: memory: synopsys,ddrc-ecc: Detach Zynq DDRC controller support
soc: sunxi: sram: Add support for the D1 system control
soc: sunxi: sram: Export the LDO control register
soc: sunxi: sram: Save a pointer to the OF match data
soc: sunxi: sram: Return void from the release function
soc: apple: rtkit: Add apple_rtkit_poll
soc: imx: add i.MX93 media blk ctrl driver
soc: imx: add i.MX93 SRC power domain driver
soc: imx: imx8m-blk-ctrl: Use genpd_xlate_onecell
soc: imx: imx8mp-blk-ctrl: handle PCIe PHY resets
soc: imx: imx8m-blk-ctrl: add i.MX8MP VPU blk ctrl
soc: imx: add i.MX8MP HDMI blk ctrl HDCP/HRV_MWR
soc: imx: add icc paths for i.MX8MP hsio/hdmi blk ctrl
soc: imx: add icc paths for i.MX8MP media blk ctrl
...
Qualcomm driver updates for 6.1
The icc-bwmon driver is expected to support measuring LLCC/DDR bandwidth
on SDM845 and SC7280.
The LLCC driver is extended to provide per-platform register mappings to
the LLCC EDAC driver. The QMI encoder/decoder is updated to allow the
passed qmi_elem_info to be const.
Support for SDM845 is added to the sleep stats driver. Power-domains for
the SM6375 platform is added to RPMPD and the platform is added to
socinfo, together with the PM6125 pmic id.
A couple of of_node reference issues are corrected in the smem state and
smsm drivers.
The Qualcomm SCM driver binding is converted to YAML.
* tag 'qcom-drivers-for-6.1' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (29 commits)
soc: qcom: rpmpd: Add SM6375 support
dt-bindings: power: rpmpd: Add SM6375 power domains
firmware: qcom: scm: remove unused __qcom_scm_init declaration
dt-bindings: power: qcom,rpmpd: drop non-working codeaurora.org emails
soc: qcom: icc-bwmon: force clear counter/irq registers
soc: qcom: icc-bwmon: add support for sc7280 LLCC BWMON
dt-bindings: interconnect: qcom,msm8998-bwmon: Add support for sc7280 BWMONs
soc: qcom: llcc: Pass LLCC version based register offsets to EDAC driver
soc: qcom: llcc: Rename reg_offset structs to reflect LLCC version
soc: qcom: qmi: use const for struct qmi_elem_info
soc: qcom: icc-bwmon: remove redundant ret variable
dt-bindings: soc: qcom: stats: Document SDM845 compatible
soc: qcom: stats: Add SDM845 stats config and compatible
dt-bindings: firmware: document Qualcomm SM6115 SCM
soc: qcom: Make QCOM_RPMPD depend on OF
dt-bindings: firmware: convert Qualcomm SCM binding to the yaml
soc: qcom: socinfo: Add PM6125 ID
soc: qcom: socinfo: Add an ID for SM6375
soc: qcom: smem_state: Add refcounting for the 'state->of_node'
soc: qcom: smsm: Fix refcount leak bugs in qcom_smsm_probe()
...
Link: https://lore.kernel.org/r/20220921155753.1316308-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
pmic-wrapper:
- add support for mt8188
SVS:
- several driver cleanups
power-domain:
- several cleanups of the dt-bindings and driver
mutex:
- add support to mt6795 disp mutex
- add support for mt8186 mdp3 mutex
* tag 'v6.0-next-soc' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
soc: mediatek: Add mmsys func to adapt to dpi output for MT8186
soc: mediatek: mutex: Add support for MT6795 Helio X10 display mutex
dt-bindings: soc: mediatek: Add display mutex support for MT6795
soc: mediatek: mutex: Add mt8186 mutex mod settings for mdp3
dt-bindings: soc: mediatek: Add mdp3 mutex support for mt8186
soc: mediatek: pm-domains: Simplify some error message
soc: mediatek: mtk-svs: Explicitly include bitfield header
soc: mediatek: mtk-svs: Use bitfield access macros where possible
soc: mediatek: mtk-svs: Commonize t-calibration-data fuse array read
dt-bindings: power: mediatek: Update maintainer list
dt-bindings: power: mediatek: Support naming power controller node with unit address
dt-bindings: power: mediatek: Refine multiple level power domain nodes
soc: mediatek: mtk-svs: Use devm variant for dev_pm_opp_of_add_table()
soc: mediatek: mtk-svs: Drop of_match_ptr() for of_match_table
soc: mediatek: mtk-svs: Remove hardcoded irqflags
soc: mediatek: mtk-svs: Switch to platform_get_irq()
dt-bindings: soc: mediatek: pwrap: add compatible for mt8188
soc: mediatek: Let PMIC Wrapper and SCPSYS depend on OF
Link: https://lore.kernel.org/r/498fe3e5-a237-121a-d500-fbb0994906cb@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
