[ Upstream commit 3aff3b4b98 ]
This commit fixes the pacing_gain to remain at BBR_UNIT (1.0) when
using lt_bw and returning from the PROBE_RTT state to PROBE_BW.
Previously, when using lt_bw, upon exiting PROBE_RTT and entering
PROBE_BW the bbr_reset_probe_bw_mode() code could sometimes randomly
end up with a cycle_idx of 0 and hence have bbr_advance_cycle_phase()
set a pacing gain above 1.0. In such cases this would result in a
pacing rate that is 1.25x higher than intended, potentially resulting
in a high loss rate for a little while until we stop using the lt_bw a
bit later.
This commit is a stable candidate for kernels back as far as 4.9.
Fixes: 0f8782ea14 ("tcp_bbr: add BBR congestion control")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Reported-by: Beyers Cronje <bcronje@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit edbe69ef2c ]
This patch effectively reverts commit 9f1c2674b3 ("net: memcontrol:
defer call to mem_cgroup_sk_alloc()").
Moving mem_cgroup_sk_alloc() to the inet_csk_accept() completely breaks
memcg socket memory accounting, as packets received before memcg
pointer initialization are not accounted and are causing refcounting
underflow on socket release.
Actually the free-after-use problem was fixed by
commit c0576e3975 ("net: call cgroup_sk_alloc() earlier in
sk_clone_lock()") for the cgroup pointer.
So, let's revert it and call mem_cgroup_sk_alloc() just before
cgroup_sk_alloc(). This is safe, as we hold a reference to the socket
we're cloning, and it holds a reference to the memcg.
Also, let's drop BUG_ON(mem_cgroup_is_root()) check from
mem_cgroup_sk_alloc(). I see no reasons why bumping the root
memcg counter is a good reason to panic, and there are no realistic
ways to hit it.
Signed-off-by: Roman Gushchin <guro@fb.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9b42d55a66 ]
socket can be disconnected and gets transformed back to a listening
socket, if sk_frag.page is not released, which will be cloned into
a new socket by sk_clone_lock, but the reference count of this page
is increased, lead to a use after free or double free issue
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6503a30440 ]
Commit 3765d35ed8 ("net: ipv4: Convert inet_rtm_getroute to rcu
versions of route lookup") broke "ip route get" in the presence
of rules that specify iif lo.
Host-originated traffic always has iif lo, because
ip_route_output_key_hash and ip6_route_output_flags set the flow
iif to LOOPBACK_IFINDEX. Thus, putting "iif lo" in an ip rule is a
convenient way to select only originated traffic and not forwarded
traffic.
inet_rtm_getroute used to match these rules correctly because
even though it sets the flow iif to 0, it called
ip_route_output_key which overwrites iif with LOOPBACK_IFINDEX.
But now that it calls ip_route_output_key_hash_rcu, the ifindex
will remain 0 and not match the iif lo in the rule. As a result,
"ip route get" will return ENETUNREACH.
Fixes: 3765d35ed8 ("net: ipv4: Convert inet_rtm_getroute to rcu versions of route lookup")
Tested: https://android.googlesource.com/kernel/tests/+/master/net/test/multinetwork_test.py passes again
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4ee806d511 ]
When a tcp socket is closed, if it detects that its net namespace is
exiting, close immediately and do not wait for FIN sequence.
For normal sockets, a reference is taken to their net namespace, so it will
never exit while the socket is open. However, kernel sockets do not take a
reference to their net namespace, so it may begin exiting while the kernel
socket is still open. In this case if the kernel socket is a tcp socket,
it will stay open trying to complete its close sequence. The sock's dst(s)
hold a reference to their interface, which are all transferred to the
namespace's loopback interface when the real interfaces are taken down.
When the namespace tries to take down its loopback interface, it hangs
waiting for all references to the loopback interface to release, which
results in messages like:
unregister_netdevice: waiting for lo to become free. Usage count = 1
These messages continue until the socket finally times out and closes.
Since the net namespace cleanup holds the net_mutex while calling its
registered pernet callbacks, any new net namespace initialization is
blocked until the current net namespace finishes exiting.
After this change, the tcp socket notices the exiting net namespace, and
closes immediately, releasing its dst(s) and their reference to the
loopback interface, which lets the net namespace continue exiting.
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1711407
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=97811
Signed-off-by: Dan Streetman <ddstreet@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ad23b75093 ]
Commit "net: igmp: Use correct source address on IGMPv3 reports"
introduced a check to validate the source address of locally generated
IGMPv3 packets.
Instead of checking the local interface address directly, it uses
inet_ifa_match(fl4->saddr, ifa), which checks if the address is on the
local subnet (or equal to the point-to-point address if used).
This breaks for point-to-point interfaces, so check against
ifa->ifa_local directly.
Cc: Kevin Cernekee <cernekee@chromium.org>
Fixes: a46182b002 ("net: igmp: Use correct source address on IGMPv3 reports")
Reported-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cd9ff4de01 ]
Map all lookup neigh keys to INADDR_ANY for loopback/point-to-point devices
to avoid making an entry for every remote ip the device needs to talk to.
This used the be the old behavior but became broken in a263b30936
(ipv4: Make neigh lookups directly in output packet path) and later removed
in 0bb4087cbe (ipv4: Fix neigh lookup keying over loopback/point-to-point
devices) because it was broken.
Signed-off-by: Jim Westfall <jwestfall@surrealistic.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d03a45572e ]
The recently added fib_metrics_match() causes a regression for routes
with both RTAX_FEATURES and RTAX_CC_ALGO if the latter has
TCP_CONG_NEEDS_ECN flag set:
| # ip link add d0 type dummy
| # ip link set d0 up
| # ip route add 172.29.29.0/24 dev d0 features ecn congctl dctcp
| # ip route del 172.29.29.0/24 dev d0 features ecn congctl dctcp
| RTNETLINK answers: No such process
During route insertion, fib_convert_metrics() detects that the given CC
algo requires ECN and hence sets DST_FEATURE_ECN_CA bit in
RTAX_FEATURES.
During route deletion though, fib_metrics_match() compares stored
RTAX_FEATURES value with that from userspace (which obviously has no
knowledge about DST_FEATURE_ECN_CA) and fails.
Fixes: 5f9ae3d9e7 ("ipv4: do metrics match when looking up and deleting a route")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9ee11bd03c ]
When ms timestamp is used, current logic uses 1us in
tcp_rcv_rtt_update() when the real rcv_rtt is within 1 - 999us.
This could cause rcv_rtt underestimation.
Fix it by always using a min value of 1ms if ms timestamp is used.
Fixes: 645f4c6f2e ("tcp: switch rcv_rtt_est and rcvq_space to high resolution timestamps")
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d4761754b4 ]
Mark tcp_sock during a SACK reneging event and invalidate rate samples
while marked. Such rate samples may overestimate bw by including packets
that were SACKed before reneging.
< ack 6001 win 10000 sack 7001:38001
< ack 7001 win 0 sack 8001:38001 // Reneg detected
> seq 7001:8001 // RTO, SACK cleared.
< ack 38001 win 10000
In above example the rate sample taken after the last ack will count
7001-38001 as delivered while the actual delivery rate likely could
be much lower i.e. 7001-8001.
This patch adds a new field tcp_sock.sack_reneg and marks it when we
declare SACK reneging and entering TCP_CA_Loss, and unmarks it after
the last rate sample was taken before moving back to TCP_CA_Open. This
patch also invalidates rate samples taken while tcp_sock.is_sack_reneg
is set.
Fixes: b9f64820fb ("tcp: track data delivery rate for a TCP connection")
Signed-off-by: Yousuk Seung <ysseung@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b4681c2829 ]
Since commit 0ddcf43d5d ("ipv4: FIB Local/MAIN table collapse") the
local table uses the same trie allocated for the main table when custom
rules are not in use.
When a net namespace is dismantled, the main table is flushed and freed
(via an RCU callback) before the local table. In case the callback is
invoked before the local table is iterated, a use-after-free can occur.
Fix this by iterating over the FIB tables in reverse order, so that the
main table is always freed after the local table.
v3: Reworded comment according to Alex's suggestion.
v2: Add a comment to make the fix more explicit per Dave's and Alex's
feedback.
Fixes: 0ddcf43d5d ("ipv4: FIB Local/MAIN table collapse")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8f659a03a0 ]
inet->hdrincl is racy, and could lead to uninitialized stack pointer
usage, so its value should be read only once.
Fixes: c008ba5bdc ("ipv4: Avoid reading user iov twice after raw_probe_proto_opt")
Signed-off-by: Mohamed Ghannam <simo.ghannam@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 600647d467 ]
Fix BBR so that upon notification of a loss recovery undo BBR resets
long-term bandwidth sampling.
Under high reordering, reordering events can be interpreted as loss.
If the reordering and spurious loss estimates are high enough, this
can cause BBR to spuriously estimate that we are seeing loss rates
high enough to trigger long-term bandwidth estimation. To avoid that
problem, this commit resets long-term bandwidth sampling on loss
recovery undo events.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2f6c498e4f ]
Fix BBR so that upon notification of a loss recovery undo BBR resets
the full pipe detection (STARTUP exit) state machine.
Under high reordering, reordering events can be interpreted as loss.
If the reordering and spurious loss estimates are high enough, this
could previously cause BBR to spuriously estimate that the pipe is
full.
Since spurious loss recovery means that our overall sending will have
slowed down spuriously, this commit gives a flow more time to probe
robustly for bandwidth and decide the pipe is really full.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 30791ac419 ]
The MD5-key that belongs to a connection is identified by the peer's
IP-address. When we are in tcp_v4(6)_reqsk_send_ack(), we are replying
to an incoming segment from tcp_check_req() that failed the seq-number
checks.
Thus, to find the correct key, we need to use the skb's saddr and not
the daddr.
This bug seems to have been there since quite a while, but probably got
unnoticed because the consequences are not catastrophic. We will call
tcp_v4_reqsk_send_ack only to send a challenge-ACK back to the peer,
thus the connection doesn't really fail.
Fixes: 9501f97229 ("tcp md5sig: Let the caller pass appropriate key for tcp_v{4,6}_do_calc_md5_hash().")
Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c589e69b50 ]
This commit records the "full bw reached" decision in a new
full_bw_reached bit. This is a pure refactor that does not change the
current behavior, but enables subsequent fixes and improvements.
In particular, this enables simple and clean fixes because the full_bw
and full_bw_cnt can be unconditionally zeroed without worrying about
forgetting that we estimated we filled the pipe in Startup. And it
enables future improvements because multiple code paths can be used
for estimating that we filled the pipe in Startup; any new code paths
only need to set this bit when they think the pipe is full.
Note that this fix intentionally reduces the width of the full_bw_cnt
counter, since we have never used the most significant bit.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a46182b002 ]
Closing a multicast socket after the final IPv4 address is deleted
from an interface can generate a membership report that uses the
source IP from a different interface. The following test script, run
from an isolated netns, reproduces the issue:
#!/bin/bash
ip link add dummy0 type dummy
ip link add dummy1 type dummy
ip link set dummy0 up
ip link set dummy1 up
ip addr add 10.1.1.1/24 dev dummy0
ip addr add 192.168.99.99/24 dev dummy1
tcpdump -U -i dummy0 &
socat EXEC:"sleep 2" \
UDP4-DATAGRAM:239.101.1.68:8889,ip-add-membership=239.0.1.68:10.1.1.1 &
sleep 1
ip addr del 10.1.1.1/24 dev dummy0
sleep 5
kill %tcpdump
RFC 3376 specifies that the report must be sent with a valid IP source
address from the destination subnet, or from address 0.0.0.0. Add an
extra check to make sure this is the case.
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b5476022bb ]
IPv4 stack reacts to changes to small MTU, by disabling itself under
RTNL.
But there is a window where threads not using RTNL can see a wrong
device mtu. This can lead to surprises, in igmp code where it is
assumed the mtu is suitable.
Fix this by reading device mtu once and checking IPv4 minimal MTU.
This patch adds missing IPV4_MIN_MTU define, to not abuse
ETH_MIN_MTU anymore.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 258bbb1b0e ]
The ICMP implementation currently replies to an ICMP time exceeded message
(type 11) with an ICMP host unreachable message (type 3, code 1).
However, time exceeded messages can either represent "time to live exceeded
in transit" (code 0) or "fragment reassembly time exceeded" (code 1).
Unconditionally replying to "fragment reassembly time exceeded" with
host unreachable messages might cause unjustified connection resets
which are now easily triggered as UFO has been removed, because, in turn,
sending large buffers triggers IP fragmentation.
The issue can be easily reproduced by running a lot of UDP streams
which is likely to trigger IP fragmentation:
# start netserver in the test namespace
ip netns add test
ip netns exec test netserver
# create a VETH pair
ip link add name veth0 type veth peer name veth0 netns test
ip link set veth0 up
ip -n test link set veth0 up
for i in $(seq 20 29); do
# assign addresses to both ends
ip addr add dev veth0 192.168.$i.1/24
ip -n test addr add dev veth0 192.168.$i.2/24
# start the traffic
netperf -L 192.168.$i.1 -H 192.168.$i.2 -t UDP_STREAM -l 0 &
done
# wait
send_data: data send error: No route to host (errno 113)
netperf: send_omni: send_data failed: No route to host
We need to differentiate instead: if fragment reassembly time exceeded
is reported, we need to silently drop the packet,
if time to live exceeded is reported, maintain the current behaviour.
In both cases increment the related error count "icmpInTimeExcds".
While at it, fix a typo in a comment, and convert the if statement
into a switch to mate it more readable.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 164a5e7ad5 ]
ipv4_default_advmss() incorrectly uses the device MTU instead
of the route provided one. IPv6 has the proper behavior,
lets harmonize the two protocols.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0c19f846d5 ]
Tuntap and similar devices can inject GSO packets. Accept type
VIRTIO_NET_HDR_GSO_UDP, even though not generating UFO natively.
Processes are expected to use feature negotiation such as TUNSETOFFLOAD
to detect supported offload types and refrain from injecting other
packets. This process breaks down with live migration: guest kernels
do not renegotiate flags, so destination hosts need to expose all
features that the source host does.
Partially revert the UFO removal from 182e0b6b5846~1..d9d30adf5677.
This patch introduces nearly(*) no new code to simplify verification.
It brings back verbatim tuntap UFO negotiation, VIRTIO_NET_HDR_GSO_UDP
insertion and software UFO segmentation.
It does not reinstate protocol stack support, hardware offload
(NETIF_F_UFO), SKB_GSO_UDP tunneling in SKB_GSO_SOFTWARE or reception
of VIRTIO_NET_HDR_GSO_UDP packets in tuntap.
To support SKB_GSO_UDP reappearing in the stack, also reinstate
logic in act_csum and openvswitch. Achieve equivalence with v4.13 HEAD
by squashing in commit 939912216f ("net: skb_needs_check() removes
CHECKSUM_UNNECESSARY check for tx.") and reverting commit 8d63bee643
("net: avoid skb_warn_bad_offload false positives on UFO").
(*) To avoid having to bring back skb_shinfo(skb)->ip6_frag_id,
ipv6_proxy_select_ident is changed to return a __be32 and this is
assigned directly to the frag_hdr. Also, SKB_GSO_UDP is inserted
at the end of the enum to minimize code churn.
Tested
Booted a v4.13 guest kernel with QEMU. On a host kernel before this
patch `ethtool -k eth0` shows UFO disabled. After the patch, it is
enabled, same as on a v4.13 host kernel.
A UFO packet sent from the guest appears on the tap device:
host:
nc -l -p -u 8000 &
tcpdump -n -i tap0
guest:
dd if=/dev/zero of=payload.txt bs=1 count=2000
nc -u 192.16.1.1 8000 < payload.txt
Direct tap to tap transmission of VIRTIO_NET_HDR_GSO_UDP succeeds,
packets arriving fragmented:
./with_tap_pair.sh ./tap_send_ufo tap0 tap1
(from https://github.com/wdebruij/kerneltools/tree/master/tests)
Changes
v1 -> v2
- simplified set_offload change (review comment)
- documented test procedure
Link: http://lkml.kernel.org/r/<CAF=yD-LuUeDuL9YWPJD9ykOZ0QCjNeznPDr6whqZ9NGMNF12Mw@mail.gmail.com>
Fixes: fb652fdfe8 ("macvlan/macvtap: Remove NETIF_F_UFO advertisement.")
Reported-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ed66dfaf23 ]
Fix the TLP scheduling logic so that when scheduling a TLP probe, we
ensure that the estimated time at which an RTO would fire accounts for
the fact that ACKs indicating forward progress should push back RTO
times.
After the following fix:
df92c8394e ("tcp: fix xmit timer to only be reset if data ACKed/SACKed")
we had an unintentional behavior change in the following kind of
scenario: suppose the RTT variance has been very low recently. Then
suppose we send out a flight of N packets and our RTT is 100ms:
t=0: send a flight of N packets
t=100ms: receive an ACK for N-1 packets
The response before df92c8394e that was:
-> schedule a TLP for now + RTO_interval
The response after df92c8394e is:
-> schedule a TLP for t=0 + RTO_interval
Since RTO_interval = srtt + RTT_variance, this means that we have
scheduled a TLP timer at a point in the future that only accounts for
RTT_variance. If the RTT_variance term is small, this means that the
timer fires soon.
Before df92c8394e this would not happen, because in that code, when
we receive an ACK for a prefix of flight, we did:
1) Near the top of tcp_ack(), switch from TLP timer to RTO
at write_queue_head->paket_tx_time + RTO_interval:
if (icsk->icsk_pending == ICSK_TIME_LOSS_PROBE)
tcp_rearm_rto(sk);
2) In tcp_clean_rtx_queue(), update the RTO to now + RTO_interval:
if (flag & FLAG_ACKED) {
tcp_rearm_rto(sk);
3) In tcp_ack() after tcp_fastretrans_alert() switch from RTO
to TLP at now + RTO_interval:
if (icsk->icsk_pending == ICSK_TIME_RETRANS)
tcp_schedule_loss_probe(sk);
In df92c8394e we removed that 3-phase dance, and instead directly
set the TLP timer once: we set the TLP timer in cases like this to
write_queue_head->packet_tx_time + RTO_interval. So if the RTT
variance is small, then this means that this is setting the TLP timer
to fire quite soon. This means if the ACK for the tail of the flight
takes longer than an RTT to arrive (often due to delayed ACKs), then
the TLP timer fires too quickly.
Fixes: df92c8394e ("tcp: fix xmit timer to only be reset if data ACKed/SACKed")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8632385022 ]
When I switched rcv_rtt_est to high resolution timestamps, I forgot
that tp->tcp_mstamp needed to be refreshed in tcp_rcv_space_adjust()
Using an old timestamp leads to autotuning lags.
Fixes: 645f4c6f2e ("tcp: switch rcv_rtt_est and rcvq_space to high resolution timestamps")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cfac7f836a ]
Maciej Żenczykowski reported some panics in tcp_twsk_destructor()
that might be caused by the following bug.
timewait timer is pinned to the cpu, because we want to transition
timwewait refcount from 0 to 4 in one go, once everything has been
initialized.
At the time commit ed2e923945 ("tcp/dccp: fix timewait races in timer
handling") was merged, TCP was always running from BH habdler.
After commit 5413d1babe ("net: do not block BH while processing
socket backlog") we definitely can run tcp_time_wait() from process
context.
We need to block BH in the critical section so that the pinned timer
has still its purpose.
This bug is more likely to happen under stress and when very small RTO
are used in datacenter flows.
Fixes: 5413d1babe ("net: do not block BH while processing socket backlog")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Maciej Żenczykowski <maze@google.com>
Acked-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e39d524611 ]
Now when creating fnhe for redirect, it sets fnhe_expires for this
new route cache. But when updating the exist one, it doesn't do it.
It will cause this fnhe never to be expired.
Paolo already noticed it before, in Jianlin's test case, it became
even worse:
When ip route flush cache, the old fnhe is not to be removed, but
only clean it's members. When redirect comes again, this fnhe will
be found and updated, but never be expired due to fnhe_expires not
being set.
So fix it by simply updating fnhe_expires even it's for redirect.
Fixes: aee06da672 ("ipv4: use seqlock for nh_exceptions")
Reported-by: Jianlin Shi <jishi@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cebe84c619 ]
Now when ip route flush cache and it turn out all fnhe_genid != genid.
If a redirect/pmtu icmp packet comes and the old fnhe is found and all
it's members but fnhe_genid will be updated.
Then next time when it looks up route and tries to rebind this fnhe to
the new dst, the fnhe will be flushed due to fnhe_genid != genid. It
causes this redirect/pmtu icmp packet acutally not to be applied.
This patch is to also reset fnhe_genid when updating a route cache.
Fixes: 5aad1de5ea ("ipv4: use separate genid for next hop exceptions")
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the cause of an WARNING indicatng TCP has pending
retransmission in Open state in tcp_fastretrans_alert().
The root cause is a bad interaction between path mtu probing,
if enabled, and the RACK loss detection. Upong receiving a SACK
above the sequence of the MTU probing packet, RACK could mark the
probe packet lost in tcp_fastretrans_alert(), prior to calling
tcp_simple_retransmit().
tcp_simple_retransmit() only enters Loss state if it newly marks
the probe packet lost. If the probe packet is already identified as
lost by RACK, the sender remains in Open state with some packets
marked lost and retransmitted. Then the next SACK would trigger
the warning. The likely scenario is that the probe packet was
lost due to its size or network congestion. The actual impact of
this warning is small by potentially entering fast recovery an
ACK later.
The simple fix is always entering recovery (Loss) state if some
packet is marked lost during path MTU probing.
Fixes: a0370b3f3f ("tcp: enable RACK loss detection to trigger recovery")
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Reported-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Reported-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a GSO skb of truesize O is segmented into 2 new skbs of truesize N1
and N2, we want to transfer socket ownership to the new fresh skbs.
In order to avoid expensive atomic operations on a cache line subject to
cache bouncing, we replace the sequence :
refcount_add(N1, &sk->sk_wmem_alloc);
refcount_add(N2, &sk->sk_wmem_alloc); // repeated by number of segments
refcount_sub(O, &sk->sk_wmem_alloc);
by a single
refcount_add(sum_of(N) - O, &sk->sk_wmem_alloc);
Problem is :
In some pathological cases, sum(N) - O might be a negative number, and
syzkaller bot was apparently able to trigger this trace [1]
atomic_t was ok with this construct, but we need to take care of the
negative delta with refcount_t
[1]
refcount_t: saturated; leaking memory.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 8404 at lib/refcount.c:77 refcount_add_not_zero+0x198/0x200 lib/refcount.c:77
Kernel panic - not syncing: panic_on_warn set ...
CPU: 0 PID: 8404 Comm: syz-executor2 Not tainted 4.14.0-rc5-mm1+ #20
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:16 [inline]
dump_stack+0x194/0x257 lib/dump_stack.c:52
panic+0x1e4/0x41c kernel/panic.c:183
__warn+0x1c4/0x1e0 kernel/panic.c:546
report_bug+0x211/0x2d0 lib/bug.c:183
fixup_bug+0x40/0x90 arch/x86/kernel/traps.c:177
do_trap_no_signal arch/x86/kernel/traps.c:211 [inline]
do_trap+0x260/0x390 arch/x86/kernel/traps.c:260
do_error_trap+0x120/0x390 arch/x86/kernel/traps.c:297
do_invalid_op+0x1b/0x20 arch/x86/kernel/traps.c:310
invalid_op+0x18/0x20 arch/x86/entry/entry_64.S:905
RIP: 0010:refcount_add_not_zero+0x198/0x200 lib/refcount.c:77
RSP: 0018:ffff8801c606e3a0 EFLAGS: 00010282
RAX: 0000000000000026 RBX: 0000000000001401 RCX: 0000000000000000
RDX: 0000000000000026 RSI: ffffc900036fc000 RDI: ffffed0038c0dc68
RBP: ffff8801c606e430 R08: 0000000000000001 R09: 0000000000000000
R10: ffff8801d97f5eba R11: 0000000000000000 R12: ffff8801d5acf73c
R13: 1ffff10038c0dc75 R14: 00000000ffffffff R15: 00000000fffff72f
refcount_add+0x1b/0x60 lib/refcount.c:101
tcp_gso_segment+0x10d0/0x16b0 net/ipv4/tcp_offload.c:155
tcp4_gso_segment+0xd4/0x310 net/ipv4/tcp_offload.c:51
inet_gso_segment+0x60c/0x11c0 net/ipv4/af_inet.c:1271
skb_mac_gso_segment+0x33f/0x660 net/core/dev.c:2749
__skb_gso_segment+0x35f/0x7f0 net/core/dev.c:2821
skb_gso_segment include/linux/netdevice.h:3971 [inline]
validate_xmit_skb+0x4ba/0xb20 net/core/dev.c:3074
__dev_queue_xmit+0xe49/0x2070 net/core/dev.c:3497
dev_queue_xmit+0x17/0x20 net/core/dev.c:3538
neigh_hh_output include/net/neighbour.h:471 [inline]
neigh_output include/net/neighbour.h:479 [inline]
ip_finish_output2+0xece/0x1460 net/ipv4/ip_output.c:229
ip_finish_output+0x85e/0xd10 net/ipv4/ip_output.c:317
NF_HOOK_COND include/linux/netfilter.h:238 [inline]
ip_output+0x1cc/0x860 net/ipv4/ip_output.c:405
dst_output include/net/dst.h:459 [inline]
ip_local_out+0x95/0x160 net/ipv4/ip_output.c:124
ip_queue_xmit+0x8c6/0x18e0 net/ipv4/ip_output.c:504
tcp_transmit_skb+0x1ab7/0x3840 net/ipv4/tcp_output.c:1137
tcp_write_xmit+0x663/0x4de0 net/ipv4/tcp_output.c:2341
__tcp_push_pending_frames+0xa0/0x250 net/ipv4/tcp_output.c:2513
tcp_push_pending_frames include/net/tcp.h:1722 [inline]
tcp_data_snd_check net/ipv4/tcp_input.c:5050 [inline]
tcp_rcv_established+0x8c7/0x18a0 net/ipv4/tcp_input.c:5497
tcp_v4_do_rcv+0x2ab/0x7d0 net/ipv4/tcp_ipv4.c:1460
sk_backlog_rcv include/net/sock.h:909 [inline]
__release_sock+0x124/0x360 net/core/sock.c:2264
release_sock+0xa4/0x2a0 net/core/sock.c:2776
tcp_sendmsg+0x3a/0x50 net/ipv4/tcp.c:1462
inet_sendmsg+0x11f/0x5e0 net/ipv4/af_inet.c:763
sock_sendmsg_nosec net/socket.c:632 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:642
___sys_sendmsg+0x31c/0x890 net/socket.c:2048
__sys_sendmmsg+0x1e6/0x5f0 net/socket.c:2138
Fixes: 14afee4b60 ("net: convert sock.sk_wmem_alloc from atomic_t to refcount_t")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes DSACK-based undo when sender is in Open State and
an ACK advances snd_una.
Example scenario:
- Sender goes into recovery and makes some spurious rtx.
- It comes out of recovery and enters into open state.
- It sends some more packets, let's say 4.
- The receiver sends an ACK for the first two, but this ACK is lost.
- The sender receives ack for first two, and DSACK for previous
spurious rtx.
Signed-off-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yousuk Seung <ysseung@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Hopefully this is the last batch of networking fixes for 4.14
Fingers crossed...
1) Fix stmmac to use the proper sized OF property read, from Bhadram
Varka.
2) Fix use after free in net scheduler tc action code, from Cong
Wang.
3) Fix SKB control block mangling in tcp_make_synack().
4) Use proper locking in fib_dump_info(), from Florian Westphal.
5) Fix IPG encodings in systemport driver, from Florian Fainelli.
6) Fix division by zero in NV TCP congestion control module, from
Konstantin Khlebnikov.
7) Fix use after free in nf_reject_ipv4, from Tejaswi Tanikella"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: systemport: Correct IPG length settings
tcp: do not mangle skb->cb[] in tcp_make_synack()
fib: fib_dump_info can no longer use __in_dev_get_rtnl
stmmac: use of_property_read_u32 instead of read_u8
net_sched: hold netns refcnt for each action
net_sched: acquire RTNL in tc_action_net_exit()
net: vrf: correct FRA_L3MDEV encode type
tcp_nv: fix division by zero in tcpnv_acked()
netfilter: nf_reject_ipv4: Fix use-after-free in send_reset
netfilter: nft_set_hash: disable fast_ops for 2-len keys
Christoph Paasch sent a patch to address the following issue :
tcp_make_synack() is leaving some TCP private info in skb->cb[],
then send the packet by other means than tcp_transmit_skb()
tcp_transmit_skb() makes sure to clear skb->cb[] to not confuse
IPv4/IPV6 stacks, but we have no such cleanup for SYNACK.
tcp_make_synack() should not use tcp_init_nondata_skb() :
tcp_init_nondata_skb() really should be limited to skbs put in write/rtx
queues (the ones that are only sent via tcp_transmit_skb())
This patch fixes the issue and should even save few cpu cycles ;)
Fixes: 971f10eca1 ("tcp: better TCP_SKB_CB layout to reduce cache line misses")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Christoph Paasch <cpaasch@apple.com>
Reviewed-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported yet another regression added with DOIT_UNLOCKED.
When nexthop is marked as dead, fib_dump_info uses __in_dev_get_rtnl():
./include/linux/inetdevice.h:230 suspicious rcu_dereference_protected() usage!
rcu_scheduler_active = 2, debug_locks = 1
1 lock held by syz-executor2/23859:
#0: (rcu_read_lock){....}, at: [<ffffffff840283f0>]
inet_rtm_getroute+0xaa0/0x2d70 net/ipv4/route.c:2738
[..]
lockdep_rcu_suspicious+0x123/0x170 kernel/locking/lockdep.c:4665
__in_dev_get_rtnl include/linux/inetdevice.h:230 [inline]
fib_dump_info+0x1136/0x13d0 net/ipv4/fib_semantics.c:1377
inet_rtm_getroute+0xf97/0x2d70 net/ipv4/route.c:2785
..
This isn't safe anymore, callers either hold RTNL mutex or rcu read lock,
so these spots must use rcu_dereference_rtnl() or plain rcu_derefence()
(plus unconditional rcu read lock).
This does the latter.
Fixes: 394f51abb3 ("ipv4: route: set ipv4 RTM_GETROUTE to not use rtnl")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains two one-liner fixes for your net tree,
they are:
1) Disable fast hash operations for 2-bytes length keys which is leading
to incorrect lookups in nf_tables, from Anatole Denis.
2) Reload pointer ipv4 header after ip_route_me_harder() given this may
result in use-after-free due to skbuff header reallocation, patch
from Tejaswi Tanikella.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Average RTT could become zero. This happened in real life at least twice.
This patch treats zero as 1us.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Acked-by: Lawrence Brakmo <Brakmo@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on SNMP values provided by Roman, Yuchung made the observation
that some crashes in tcp_sacktag_walk() might be caused by MTU probing.
Looking at tcp_mtu_probe(), I found that when a new skb was placed
in front of the write queue, we were not updating tcp highest sack.
If one skb is freed because all its content was copied to the new skb
(for MTU probing), then tp->highest_sack could point to a now freed skb.
Bad things would then happen, including infinite loops.
This patch renames tcp_highest_sack_combine() and uses it
from tcp_mtu_probe() to fix the bug.
Note that I also removed one test against tp->sacked_out,
since we want to replace tp->highest_sack regardless of whatever
condition, since keeping a stale pointer to freed skb is a recipe
for disaster.
Fixes: a47e5a988a ("[TCP]: Convert highest_sack to sk_buff to allow direct access")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Reported-by: Roman Gushchin <guro@fb.com>
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
niph is not updated after pskb_expand_head changes the skb head. It
still points to the freed data, which is then used to update tot_len and
checksum. This could cause use-after-free poison crash.
Update niph, if ip_route_me_harder does not fail.
This only affects the interaction with REJECT targets and br_netfilter.
Signed-off-by: Tejaswi Tanikella <tejaswit@codeaurora.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In the unlikely event tcp_mtu_probe() is sending a packet, we
want tp->tcp_mstamp being as accurate as possible.
This means we need to call tcp_mstamp_refresh() a bit earlier in
tcp_write_xmit().
Fixes: 385e20706f ("tcp: use tp->tcp_mstamp in output path")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
t->err_count is used to count the link failure on tunnel and an err
will be reported to user socket in tx path if t->err_count is not 0.
udp socket could even return EHOSTUNREACH to users.
Since commit fd58156e45 ("IPIP: Use ip-tunneling code.") removed
the 'switch check' for icmp type in ipip_err(), err_count would be
increased by the icmp packet with ICMP_EXC_FRAGTIME code. an link
failure would be reported out due to this.
In Jianlin's case, when receiving ICMP_EXC_FRAGTIME a icmp packet,
udp netperf failed with the err:
send_data: data send error: No route to host (errno 113)
We expect this error reported from tunnel to socket when receiving
some certain type icmp, but not ICMP_EXC_FRAGTIME, ICMP_SR_FAILED
or ICMP_PARAMETERPROB ones.
This patch is to bring 'switch check' for icmp type back to ipip_err
so that it only reports link failure for the right type icmp, just as
in ipgre_err() and ipip6_err().
Fixes: fd58156e45 ("IPIP: Use ip-tunneling code.")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation calls tcp_rate_skb_sent() when tcp_transmit_skb()
is called when it clones skb only. Not calling tcp_rate_skb_sent() is OK
for all such code paths except from __tcp_retransmit_skb() which happens
when skb->data address is not aligned. This may rarely happen e.g. when
small amount of data is sent initially and the receiver partially acks
odd number of bytes for some reason, possibly malicious.
Signed-off-by: Yousuk Seung <ysseung@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In my first attempt to fix the lockdep splat, I forgot we could
enter inet_csk_route_req() with a freshly allocated request socket,
for which refcount has not yet been elevated, due to complex
SLAB_TYPESAFE_BY_RCU rules.
We either are in rcu_read_lock() section _or_ we own a refcount on the
request.
Correct RCU verb to use here is rcu_dereference_check(), although it is
not possible to prove we actually own a reference on a shared
refcount :/
In v2, I added ireq_opt_deref() helper and use in three places, to fix other
possible splats.
[ 49.844590] lockdep_rcu_suspicious+0xea/0xf3
[ 49.846487] inet_csk_route_req+0x53/0x14d
[ 49.848334] tcp_v4_route_req+0xe/0x10
[ 49.850174] tcp_conn_request+0x31c/0x6a0
[ 49.851992] ? __lock_acquire+0x614/0x822
[ 49.854015] tcp_v4_conn_request+0x5a/0x79
[ 49.855957] ? tcp_v4_conn_request+0x5a/0x79
[ 49.858052] tcp_rcv_state_process+0x98/0xdcc
[ 49.859990] ? sk_filter_trim_cap+0x2f6/0x307
[ 49.862085] tcp_v4_do_rcv+0xfc/0x145
[ 49.864055] ? tcp_v4_do_rcv+0xfc/0x145
[ 49.866173] tcp_v4_rcv+0x5ab/0xaf9
[ 49.868029] ip_local_deliver_finish+0x1af/0x2e7
[ 49.870064] ip_local_deliver+0x1b2/0x1c5
[ 49.871775] ? inet_del_offload+0x45/0x45
[ 49.873916] ip_rcv_finish+0x3f7/0x471
[ 49.875476] ip_rcv+0x3f1/0x42f
[ 49.876991] ? ip_local_deliver_finish+0x2e7/0x2e7
[ 49.878791] __netif_receive_skb_core+0x6d3/0x950
[ 49.880701] ? process_backlog+0x7e/0x216
[ 49.882589] __netif_receive_skb+0x1d/0x5e
[ 49.884122] process_backlog+0x10c/0x216
[ 49.885812] net_rx_action+0x147/0x3df
Fixes: a6ca7abe53 ("tcp/dccp: fix lockdep splat in inet_csk_route_req()")
Fixes: c92e8c02fe ("tcp/dccp: fix ireq->opt races")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: kernel test robot <fengguang.wu@intel.com>
Reported-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following lockdep splat in inet_csk_route_req()
lockdep_rcu_suspicious
inet_csk_route_req
tcp_v4_send_synack
tcp_rtx_synack
inet_rtx_syn_ack
tcp_fastopen_synack_time
tcp_retransmit_timer
tcp_write_timer_handler
tcp_write_timer
call_timer_fn
Thread running inet_csk_route_req() owns a reference on the request
socket, so we have the guarantee ireq->ireq_opt wont be changed or
freed.
lockdep can enforce this invariant for us.
Fixes: c92e8c02fe ("tcp/dccp: fix ireq->opt races")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Levin, Alexander (Sasha Levin)
Neal Cardwell
Roman Gushchin
Li RongQing
Eric Dumazet
Lorenzo Colitti
Willem de Bruijn
Dan Streetman
Felix Fietkau
Jim Westfall
Phil Sutter
Wei Wang
Yousuk Seung
Ido Schimmel
Mohamed Ghannam
Christoph Paasch
Kevin Cernekee
Hoang Tran
William Tu
Matteo Croce
Xin Long
Yuchung Cheng
Priyaranjan Jha
Linus Torvalds
Florian Westphal
Greg Kroah-Hartman
David S. Miller
Konstantin Khlebnikov
Tejaswi Tanikella