mirror of
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git
synced 2026-06-11 15:46:40 +02:00
dt-bindings: usb: ti,dwc3: convert to DT schema
Convert OMAP DWC3 USB Glue Layer binding to DT schema. Changes made during the conversion: - Drop the ti,hwmods property, as it is not used by any in-tree DTS files. Signed-off-by: Charan Pedumuru <charan.pedumuru@gmail.com> Reviewed-by: Rob Herring (Arm) <robh@kernel.org> Link: https://patch.msgid.link/20260127-ti-usb-v2-2-9dd6a65b43df@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit is contained in:
Charan Pedumuru
committed by
Greg Kroah-Hartman
Greg Kroah-Hartman
parent
70fcdc82cf
commit
ca47d656ad
@@ -1,80 +0,0 @@
|
||||
OMAP GLUE AND OTHER OMAP SPECIFIC COMPONENTS
|
||||
|
||||
OMAP MUSB GLUE
|
||||
- compatible : Should be "ti,omap4-musb" or "ti,omap3-musb"
|
||||
- ti,hwmods : must be "usb_otg_hs"
|
||||
- multipoint : Should be "1" indicating the musb controller supports
|
||||
multipoint. This is a MUSB configuration-specific setting.
|
||||
- num-eps : Specifies the number of endpoints. This is also a
|
||||
MUSB configuration-specific setting. Should be set to "16"
|
||||
- ram-bits : Specifies the ram address size. Should be set to "12"
|
||||
- interface-type : This is a board specific setting to describe the type of
|
||||
interface between the controller and the phy. It should be "0" or "1"
|
||||
specifying ULPI and UTMI respectively.
|
||||
- mode : Should be "3" to represent OTG. "1" signifies HOST and "2"
|
||||
represents PERIPHERAL.
|
||||
- power : Should be "50". This signifies the controller can supply up to
|
||||
100mA when operating in host mode.
|
||||
- usb-phy : the phandle for the PHY device
|
||||
- phys : the phandle for the PHY device (used by generic PHY framework)
|
||||
- phy-names : the names of the PHY corresponding to the PHYs present in the
|
||||
*phy* phandle.
|
||||
|
||||
Optional properties:
|
||||
- ctrl-module : phandle of the control module this glue uses to write to
|
||||
mailbox
|
||||
|
||||
SOC specific device node entry
|
||||
usb_otg_hs: usb_otg_hs@4a0ab000 {
|
||||
compatible = "ti,omap4-musb";
|
||||
ti,hwmods = "usb_otg_hs";
|
||||
multipoint = <1>;
|
||||
num-eps = <16>;
|
||||
ram-bits = <12>;
|
||||
ctrl-module = <&omap_control_usb>;
|
||||
phys = <&usb2_phy>;
|
||||
phy-names = "usb2-phy";
|
||||
};
|
||||
|
||||
Board specific device node entry
|
||||
&usb_otg_hs {
|
||||
interface-type = <1>;
|
||||
mode = <3>;
|
||||
power = <50>;
|
||||
};
|
||||
|
||||
OMAP DWC3 GLUE
|
||||
- compatible : Should be
|
||||
* "ti,dwc3" for OMAP5 and DRA7
|
||||
* "ti,am437x-dwc3" for AM437x
|
||||
- ti,hwmods : Should be "usb_otg_ss"
|
||||
- reg : Address and length of the register set for the device.
|
||||
- interrupts : The irq number of this device that is used to interrupt the
|
||||
MPU
|
||||
- #address-cells, #size-cells : Must be present if the device has sub-nodes
|
||||
- utmi-mode : controls the source of UTMI/PIPE status for VBUS and OTG ID.
|
||||
It should be set to "1" for HW mode and "2" for SW mode.
|
||||
- ranges: the child address space are mapped 1:1 onto the parent address space
|
||||
|
||||
Optional Properties:
|
||||
- extcon : phandle for the extcon device omap dwc3 uses to detect
|
||||
connect/disconnect events.
|
||||
- vbus-supply : phandle to the regulator device tree node if needed.
|
||||
|
||||
Sub-nodes:
|
||||
The dwc3 core should be added as subnode to omap dwc3 glue.
|
||||
- dwc3 :
|
||||
The binding details of dwc3 can be found in:
|
||||
Documentation/devicetree/bindings/usb/snps,dwc3.yaml
|
||||
|
||||
omap_dwc3 {
|
||||
compatible = "ti,dwc3";
|
||||
ti,hwmods = "usb_otg_ss";
|
||||
reg = <0x4a020000 0x1ff>;
|
||||
interrupts = <0 93 4>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
utmi-mode = <2>;
|
||||
ranges;
|
||||
};
|
||||
|
||||
@@ -0,0 +1,100 @@
|
||||
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
|
||||
%YAML 1.2
|
||||
---
|
||||
$id: http://devicetree.org/schemas/usb/ti,dwc3.yaml#
|
||||
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
||||
|
||||
title: Texas Instruments OMAP DWC3 USB Glue Layer
|
||||
|
||||
maintainers:
|
||||
- Felipe Balbi <balbi@ti.com>
|
||||
|
||||
description:
|
||||
Texas Instruments glue layer for Synopsys DesignWare USB3 (DWC3)
|
||||
controller on OMAP and AM43xx SoCs. Manages SoC-specific integration
|
||||
including register mapping, interrupt routing, UTMI/PIPE interface mode
|
||||
selection (HW/SW), and child DWC3 core instantiation via address space
|
||||
translation. Supports both legacy single-instance and multi-instance
|
||||
(numbered) configurations.
|
||||
|
||||
properties:
|
||||
compatible:
|
||||
enum:
|
||||
- ti,dwc3
|
||||
- ti,am437x-dwc3
|
||||
|
||||
reg:
|
||||
maxItems: 1
|
||||
|
||||
interrupts:
|
||||
maxItems: 1
|
||||
|
||||
utmi-mode:
|
||||
$ref: /schemas/types.yaml#/definitions/uint32
|
||||
description:
|
||||
Controls the source of UTMI/PIPE status for VBUS and OTG ID.
|
||||
1 for HW mode, 2 for SW mode.
|
||||
enum: [1, 2]
|
||||
|
||||
"#address-cells":
|
||||
const: 1
|
||||
|
||||
"#size-cells":
|
||||
const: 1
|
||||
|
||||
ranges: true
|
||||
|
||||
extcon:
|
||||
$ref: /schemas/types.yaml#/definitions/phandle
|
||||
description:
|
||||
Phandle for the extcon device used to detect connect/
|
||||
disconnect events.
|
||||
|
||||
vbus-supply:
|
||||
description: Phandle to the regulator device tree node if needed.
|
||||
|
||||
patternProperties:
|
||||
"^usb@[0-9a-f]+$":
|
||||
type: object
|
||||
$ref: snps,dwc3.yaml#
|
||||
unevaluatedProperties: false
|
||||
|
||||
required:
|
||||
- reg
|
||||
- compatible
|
||||
- interrupts
|
||||
- "#address-cells"
|
||||
- "#size-cells"
|
||||
- utmi-mode
|
||||
- ranges
|
||||
|
||||
unevaluatedProperties: false
|
||||
|
||||
examples:
|
||||
- |
|
||||
#include <dt-bindings/interrupt-controller/arm-gic.h>
|
||||
omap_dwc3_1@0 {
|
||||
compatible = "ti,dwc3";
|
||||
reg = <0x0 0x10000>;
|
||||
interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
utmi-mode = <2>;
|
||||
ranges = <0 0 0x20000>;
|
||||
|
||||
usb@10000 {
|
||||
compatible = "snps,dwc3";
|
||||
reg = <0x10000 0x17000>;
|
||||
interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
|
||||
interrupt-names = "peripheral", "host", "otg";
|
||||
phys = <&usb2_phy1>, <&usb3_phy1>;
|
||||
phy-names = "usb2-phy", "usb3-phy";
|
||||
maximum-speed = "super-speed";
|
||||
dr_mode = "otg";
|
||||
snps,dis_u3_susphy_quirk;
|
||||
snps,dis_u2_susphy_quirk;
|
||||
};
|
||||
};
|
||||
...
|
||||
Reference in New Issue
Block a user