[ Upstream commit d23d763e00 ]
IRQ needs to be acked. for some odd reasons, reading from irq status does
not reliable help, enable acking from any register to be on the safe side
and read the irq status register. Comments in the code indicate a known
unreliability with that register.
The blamed commit was tested with mpu6050 in lg,p895 and lg,p880 according
to Tested-bys. But with the MPU9150 in the Epson Moverio BT-200 this leads
to irq storms without properly acking the irq.
Fixes: 0a3b517c80 ("iio: imu: inv_mpu6050: fix interrupt status read for old buggy chips")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Acked-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b79b24f578 ]
The return value from itg3200_read_reg_s16() is stored in ret but
never checked. The function unconditionally returns IIO_VAL_INT,
ignoring potential I2C read failures. This causes garbage data to
be returned to userspace when the read fails, with no error reported.
Add proper error checking to propagate the failure to callers.
Fixes: 9dbf091da0 ("iio: gyro: Add itg3200")
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1b1401522 ]
The interrupt handler reads FIFO entries in batches of N samples, where N
is the number of scan elements that have been enabled. However, the sensor
fills the FIFO one sample at a time, even when more than one channel is
enabled. Therefore,the number of entries reported by the FIFO status
registers may not be a multiple of N; if this number is not a multiple, the
number of entries read from the FIFO may exceed the number of entries
actually present.
To fix the above issue, round down the number of FIFO entries read from the
status registers so that it is always a multiple of N.
Fixes: df36de1367 ("iio: accel: add ADXL380 driver")
Signed-off-by: Francesco Lavra <flavra@baylibre.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a54e944092 ]
Passing IRQF_ONESHOT ensures that the interrupt source is masked until
the secondary (threaded) handler is done. If only a primary handler is
used then the flag makes no sense because the interrupt can not fire
(again) while its handler is running.
The flag also disallows force-threading of the primary handler and the
irq-core will warn about this.
The force-threading functionality is required on PREEMPT_RT because the
handler is using locks with can sleep on PREEMPT_RT.
Remove IRQF_ONESHOT from irqflags.
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04d390af97 ]
The interrupt handler iio_trigger_generic_data_rdy_poll() will invoke
other interrupt handler and this supposed to happen from within the
hardirq.
Use IRQF_NO_THREAD to forbid forced-threading.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62b44ebc1f ]
spi->irq from request_threaded_irq() not released when
iio_device_register() fails. Add an return value check and jump to a
common error handler when iio_device_register() fails.
Fixes: 9a4936dc89 ("staging:iio:accel:sca3000 Tidy up probe order to avoid a race.")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b010880b99 ]
Regulator requesting may result in deferred probing error which will
abort driver probing. To avoid this just use dev_err_probe which handles
deferred probing.
Fixes: 3904b28efb ("iio: gyro: Add driver for the MPU-3050 gyroscope")
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d63403d4e3 ]
A sign change is needed for proper calculation of the pressure.
This is a minor fix since it only affects users that might have custom
silicon from Honeywell that has honeywell,pmin-pascal != 0.
Also due to the fact that raw pressure values can not be lower
than output_min (400k-3.3M) there is no need to calculate a decimal for
the offset.
Fixes: 713337d914 ("iio: pressure: Honeywell mprls0025pa pressure sensor")
Signed-off-by: Petre Rodan <petre.rodan@subdimension.ro>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a228e0369 ]
Fix the scan_type sign and realbits assignment.
The pressure is a 24bit unsigned int between output_min and output_max.
transfer function A: 10% to 90% of 2^24
transfer function B: 2.5% to 22.5% of 2^24
transfer function C: 20% to 80% of 2^24
[MPR_FUNCTION_A] = { .output_min = 1677722, .output_max = 15099494 }
[MPR_FUNCTION_B] = { .output_min = 419430, .output_max = 3774874 }
[MPR_FUNCTION_C] = { .output_min = 3355443, .output_max = 13421773 }
Fixes: 713337d914 ("iio: pressure: Honeywell mprls0025pa pressure sensor")
Signed-off-by: Petre Rodan <petre.rodan@subdimension.ro>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea6b4feba8 ]
Since commit c6e126de43 ("of: Keep track of populated platform
devices") child devices will not be created by of_platform_populate()
if the devices had previously been deregistered individually so that the
OF_POPULATED flag is still set in the corresponding OF nodes.
Switch to using of_platform_depopulate() instead of open coding so that
the child devices are created if the driver is rebound.
Fixes: c6e126de43 ("of: Keep track of populated platform devices")
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
[ Adjust context ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9910159f06 ]
When one iio device is a consumer of another, it is possible that
the ->info_exist_lock of both ends up being taken when reading the
value of the consumer device.
Since they currently belong to the same lockdep class (being
initialized in a single location with mutex_init()), that results in a
lockdep warning
CPU0
----
lock(&iio_dev_opaque->info_exist_lock);
lock(&iio_dev_opaque->info_exist_lock);
*** DEADLOCK ***
May be due to missing lock nesting notation
4 locks held by sensors/414:
#0: c31fd6dc (&p->lock){+.+.}-{3:3}, at: seq_read_iter+0x44/0x4e4
#1: c4f5a1c4 (&of->mutex){+.+.}-{3:3}, at: kernfs_seq_start+0x1c/0xac
#2: c2827548 (kn->active#34){.+.+}-{0:0}, at: kernfs_seq_start+0x30/0xac
#3: c1dd2b68 (&iio_dev_opaque->info_exist_lock){+.+.}-{3:3}, at: iio_read_channel_processed_scale+0x24/0xd8
stack backtrace:
CPU: 0 UID: 0 PID: 414 Comm: sensors Not tainted 6.17.11 #5 NONE
Hardware name: Generic AM33XX (Flattened Device Tree)
Call trace:
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x44/0x60
dump_stack_lvl from print_deadlock_bug+0x2b8/0x334
print_deadlock_bug from __lock_acquire+0x13a4/0x2ab0
__lock_acquire from lock_acquire+0xd0/0x2c0
lock_acquire from __mutex_lock+0xa0/0xe8c
__mutex_lock from mutex_lock_nested+0x1c/0x24
mutex_lock_nested from iio_read_channel_raw+0x20/0x6c
iio_read_channel_raw from rescale_read_raw+0x128/0x1c4
rescale_read_raw from iio_channel_read+0xe4/0xf4
iio_channel_read from iio_read_channel_processed_scale+0x6c/0xd8
iio_read_channel_processed_scale from iio_hwmon_read_val+0x68/0xbc
iio_hwmon_read_val from dev_attr_show+0x18/0x48
dev_attr_show from sysfs_kf_seq_show+0x80/0x110
sysfs_kf_seq_show from seq_read_iter+0xdc/0x4e4
seq_read_iter from vfs_read+0x238/0x2e4
vfs_read from ksys_read+0x6c/0xec
ksys_read from ret_fast_syscall+0x0/0x1c
Just as the mlock_key already has its own lockdep class, add a
lock_class_key for the info_exist mutex.
Note that this has in theory been a problem since before IIO first
left staging, but it only occurs when a chain of consumers is in use
and that is not often done.
Fixes: ac917a8111 ("staging:iio:core set the iio_dev.info pointer to null on unregister under lock.")
Signed-off-by: Rasmus Villemoes <ravi@prevas.dk>
Reviewed-by: Peter Rosin <peda@axentia.se>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f5d203467a ]
Add missing mutex_destroy() call in iio_dev_release() to properly
clean up the mutex initialized in iio_device_alloc(). Ensure proper
resource cleanup and follows kernel practices.
Found by code review.
While at it, create a lockdep key before mutex initialisation.
This will help with converting it to the better API in the future.
Fixes: 847ec80bba ("Staging: IIO: core support for device registration and management")
Fixes: ac917a8111 ("staging:iio:core set the iio_dev.info pointer to null on unregister under lock.")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: 9910159f06 ("iio: core: add separate lockdep class for info_exist_lock")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 441ac29923 upstream.
The chip info for this variant (I2C, four channels, 14 bit, internal
reference) seems to have been left out due to oversight, so
ad5686_chip_info_tbl[ID_AD5695R] is all zeroes. Initialisation of an
AD5695R still succeeds, but the resulting IIO device has no channels and no
/dev/iio:device* node.
Add the missing chip info to the table.
Fixes: 4177381b44 ("iio:dac:ad5686: Add AD5671R/75R/94/94R/95R/96/96R support")
Signed-off-by: Andreas Kübrich <andreas.kuebrich@spektra-dresden.de>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81d5a5366d upstream.
The driver converts values read from the sensor from BE to CPU
endianness in scd4x_read_meas(). The result is then pushed into the
buffer in scd4x_trigger_handler(), so on LE architectures parsing the
buffer using the reported BE type gave wrong results.
scd4x_read_raw() which provides sysfs *_raw values is not affected, it
used the values returned by scd4x_read_meas() without further
conversion.
Fixes: 49d22b695c ("drivers: iio: chemical: Add support for Sensirion SCD4x CO2 sensor")
Signed-off-by: Fiona Klute <fiona.klute@gmx.de>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da934ef0fd upstream.
The local variable 'curr_energy' was never clamped to
PAC_193X_MIN_POWER_ACC or PAC_193X_MAX_POWER_ACC because the return
value of clamp() was not used. Fix this by assigning the clamped value
back to 'curr_energy'.
Cc: stable@vger.kernel.org
Fixes: 0fb528c825 ("iio: adc: adding support for PAC193x")
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dbdb442218 upstream.
at91_adc_interrupt can call at91_adc_touch_data_handler function
to start the work by schedule_work(&st->touch_st.workq).
If we remove the module which will call at91_adc_remove to
make cleanup, it will free indio_dev through iio_device_unregister but
quite a bit later. While the work mentioned above will be used. The
sequence of operations that may lead to a UAF bug is as follows:
CPU0 CPU1
| at91_adc_workq_handler
at91_adc_remove |
iio_device_unregister(indio_dev) |
//free indio_dev a bit later |
| iio_push_to_buffers(indio_dev)
| //use indio_dev
Fix it by ensuring that the work is canceled before proceeding with
the cleanup in at91_adc_remove.
Fixes: 23ec2774f1 ("iio: adc: at91-sama5d2_adc: add support for position and pressure channels")
Signed-off-by: Pei Xiao <xiaopei01@kylinos.cn>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ff39d6de4 upstream.
fwnode_irq_get_byname() returns a negative value on failure; if a negative
value is returned, use it as `err` argument for dev_err_probe().
While at it, add a missing trailing newline to the dev_err_probe() error
message.
Fixes: df36de1367 ("iio: accel: add ADXL380 driver")
Signed-off-by: Francesco Lavra <flavra@baylibre.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6b39824ac4 ]
The probe() function ignored the return value of spi_setup(), leaving SPI
configuration failures undetected. If spi_setup() fails, the driver should
stop initialization and propagate the error to the caller.
Add proper error handling: check the return value of spi_setup() and return
it on failure.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 2051f25d2a ("iio: adc: New driver for AD7280A Lithium Ion Battery Monitoring System")
Signed-off-by: Pavel Zhigulin <Pavel.Zhigulin@kaspersky.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c34e2e2d67 upstream.
The st_lsm6dsx_acc_channels array of struct iio_chan_spec has a non-NULL
event_spec field, indicating support for IIO events. However, event
detection is not supported for all sensors, and if userspace tries to
configure accelerometer wakeup events on a sensor device that does not
support them (e.g. LSM6DS0), st_lsm6dsx_write_event() dereferences a NULL
pointer when trying to write to the wakeup register.
Define an additional struct iio_chan_spec array whose members have a NULL
event_spec field, and use this array instead of st_lsm6dsx_acc_channels for
sensors without event detection capability.
Fixes: b5969abfa8 ("iio: imu: st_lsm6dsx: add motion events")
Signed-off-by: Francesco Lavra <flavra@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c9fb952360 ]
FIELD_PREP() checks that a value fits into the available bitfield, add a
check for step_avg to fix gcc complains.
which gcc complains about:
drivers/iio/adc/ti_am335x_adc.c: In function 'tiadc_step_config':
include/linux/compiler_types.h:572:38: error: call to
'__compiletime_assert_491' declared with attribute error: FIELD_PREP: value
too large for the field include/linux/mfd/ti_am335x_tscadc.h:58:29: note:
in expansion of macro 'FIELD_PREP'
#define STEPCONFIG_AVG(val) FIELD_PREP(GENMASK(4, 2), (val))
^~~~~~~~~~
drivers/iio/adc/ti_am335x_adc.c:127:17: note: in expansion of macro 'STEPCONFIG_AVG'
stepconfig = STEPCONFIG_AVG(ffs(adc_dev->step_avg[i]) - 1)
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202510102117.Jqxrw1vF-lkp@intel.com/
Signed-off-by: Pei Xiao <xiaopei01@kylinos.cn>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bd886cdcbf upstream.
Use correct argument to iio_str_to_fixpoint() to parse 3 decimal places.
iio_str_to_fixpoint() has a bit of an unintuitive API where the
fract_mult parameter is the multiplier of the first decimal place as if
it was already an integer. So to get 3 decimal places, fract_mult must
be 100 rather than 1000.
Fixes: 96ccdbc07a ("staging:iio:adc:ad7280a: Standardize extended ABI naming")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c92c1bc408 upstream.
There is an race-condition where device is not full working after SW reset.
Therefore it's necessary to wait some time after reset and verify shadow
registers values by reading and comparing the values before/after reset.
This mechanism is described in datasheet at least from revision D.
Fixes: 12ed27863e ("iio: accel: Add driver support for ADXL355")
Signed-off-by: Valek Andrej <andrej.v@skyrain.eu>
Signed-off-by: Kessler Markus <markus.kessler@hilti.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3aa385a9c7 upstream.
The code in bmc150-accel-core.c unconditionally calls
bmc150_accel_set_interrupt() in the iio_buffer_setup_ops,
such as on the runtime PM resume path giving a kernel
splat like this if the device has no interrupts:
Unable to handle kernel NULL pointer dereference at virtual
address 00000001 when read
PC is at bmc150_accel_set_interrupt+0x98/0x194
LR is at __pm_runtime_resume+0x5c/0x64
(...)
Call trace:
bmc150_accel_set_interrupt from bmc150_accel_buffer_postenable+0x40/0x108
bmc150_accel_buffer_postenable from __iio_update_buffers+0xbe0/0xcbc
__iio_update_buffers from enable_store+0x84/0xc8
enable_store from kernfs_fop_write_iter+0x154/0x1b4
This bug seems to have been in the driver since the beginning,
but it only manifests recently, I do not know why.
Store the IRQ number in the state struct, as this is a common
pattern in other drivers, then use this to determine if we have
IRQ support or not.
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a6b7989ff upstream.
Initially st,adc-alt-channel property was defined as an enum in the DFSDM
binding. The DFSDM binding has been changed to use the new IIO backend
framework, along with the adoption of IIO generic channels.
In this new binding st,adc-alt-channel is defined as a boolean property,
but it is still handled has an enum in DFSDM driver.
Fix st,adc-alt-channel property handling in DFSDM driver.
Fixes: 3208fa0cd9 ("iio: adc: stm32-dfsdm: adopt generic channels bindings")
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3af0c1fb1c upstream.
The `decimator` and `batch` fields of struct st_lsm6dsx_settings
are arrays indexed by sensor type, not by sensor hardware
identifier; moreover, the `batch` field is only used for the
accelerometer and gyroscope.
Change the array size for `decimator` from ST_LSM6DSX_MAX_ID to
ST_LSM6DSX_ID_MAX, and change the array size for `batch` from
ST_LSM6DSX_MAX_ID to 2; move the enum st_lsm6dsx_sensor_id
definition so that the ST_LSM6DSX_ID_MAX value is usable within
the struct st_lsm6dsx_settings definition.
Fixes: 801a6e0af0 ("iio: imu: st_lsm6dsx: add support to LSM6DSO")
Signed-off-by: Francesco Lavra <flavra@baylibre.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb372b4f46 upstream.
According to the ABI the units after application of scale and offset are
milli degree celsius for temperature thresholds and milli percent for
relative humidity thresholds. Currently the resulting units are degree
celsius for temperature thresholds and hysteresis and percent for relative
humidity thresholds and hysteresis. Change scale factor to fix this issue.
Fixes: 3ad0e7e5f0 ("iio: humidity: hdc3020: add threshold events support")
Reported-by: Chris Lesiak <chris.lesiak@licorbio.com>
Reviewed-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Signed-off-by: Dimitri Fedrau <dimitri.fedrau@liebherr.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b8dc11c0a upstream.
According to the ABI the units after application of scale and offset are
milli degrees for temperature measurements and milli percent for relative
humidity measurements. Currently the resulting units are degree celsius for
temperature measurements and percent for relative humidity measurements.
Change scale factor to fix this issue.
Fixes: c9180b8e39 ("iio: humidity: Add driver for ti HDC302x humidity sensors")
Reported-by: Chris Lesiak <chris.lesiak@licorbio.com>
Suggested-by: Chris Lesiak <chris.lesiak@licorbio.com>
Reviewed-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Signed-off-by: Dimitri Fedrau <dimitri.fedrau@liebherr.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a514bb109e upstream.
Add a new buffer accessor .get_dma_dev() in order to get the
struct device responsible for actually providing the dma channel. We
cannot assume that we can use the parent of the IIO device for mapping
the DMA buffer. This becomes important on systems (like the Xilinx/AMD
zynqMP Ultrascale) where memory (or part of it) is mapped above the
32 bit range. On such systems and given that a device by default has
a dma mask of 32 bits we would then need to rely on bounce buffers (to
swiotlb) for mapping memory above the dma mask limit.
In the process, add an iio_buffer_get_dma_dev() helper function to get
the proper DMA device.
Cc: stable@vger.kernel.org
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3db847df99 upstream.
Wire up the .get_dma_dev() callback to use the DMA buffer infrastructure's
implementation. This ensures that DMABUF operations use the correct DMA
device for mapping, which is essential for proper operation on systems
where memory is mapped above the 32-bit range.
Without this callback, the core would fall back to using the IIO device's
parent, which may not have the appropriate DMA mask configuration for
high memory access.
Fixes: 7a86d46998 ("iio: buffer-dmaengine: Support new DMABUF based userspace API")
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9c198c3cc upstream.
Implement the .get_dma_dev() callback for DMA buffers by returning the
device that owns the DMA channel. This allows the core DMABUF
infrastructure to properly map DMA buffers using the correct device,
avoiding the need for bounce buffers on systems where memory is mapped
above the 32-bit range.
The function returns the DMA queue's device, which is the actual device
responsible for DMA operations in buffer-dma implementations.
Cc: stable@vger.kernel.org
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8abbf45fcd ]
The calibrated timestamp is calculated from the nominal value using the
formula:
ts_gain[ns] ≈ ts_sensitivity - (ts_trim_coeff * val) / 1000.
The values of ts_sensitivity and ts_trim_coeff are not the same for all
devices, so it is necessary to differentiate them based on the part name.
For the correct values please consult the relevant AN.
Fixes: cb3b6b8e1b ("iio: imu: st_lsm6dsx: add odr calibration feature")
Signed-off-by: Mario Tesi <mario.tesi@st.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12c9b09e98 ]
ADC calibration might fail because of the noise on reference voltage.
To avoid calibration fail, need to meet the following requirement:
ADC reference voltage Noise < 1.8V * 1/2^ENOB
For the case which the ADC reference voltage on board do not meet
the requirement, still load the calibrated values, so ADC can also
work but maybe not that accurate.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Primoz Fiser <primoz.fiser@norik.com>
Link: https://patch.msgid.link/20250812-adc-v2-2-0260833f13b8@nxp.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0792c1984a ]
Rework the power management in inv_icm42600_core_probe() to use
devm_pm_runtime_set_active_enabled(), which simplifies the runtime PM
setup by handling activation and enabling in one step.
Remove the separate inv_icm42600_disable_pm callback, as it's no longer
needed with the devm-managed approach.
Using devm_pm_runtime_enable() also fixes the missing disable of
autosuspend.
Update inv_icm42600_disable_vddio_reg() to only disable the regulator if
the device is not suspended i.e. powered-down, preventing unbalanced
disables.
Also remove redundant error msg on regulator_disable(), the regulator
framework already emits an error message when regulator_disable() fails.
This simplifies the PM setup and avoids manipulating the usage counter
unnecessarily.
Fixes: 31c24c1e93 ("iio: imu: inv_icm42600: add core of new inv_icm42600 driver")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: https://patch.msgid.link/20250901-icm42pmreg-v3-1-ef1336246960@geanix.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit feb500c7ae upstream.
To convert level-triggered alarms into edge-triggered IIO events, alarms
are masked when they are triggered. To ensure we catch subsequent
alarms, we then periodically poll to see if the alarm is still active.
If it isn't, we unmask it. Active but masked alarms are stored in
current_masked_alarm.
If an active alarm is disabled, it will remain set in
current_masked_alarm until ams_unmask_worker clears it. If the alarm is
re-enabled before ams_unmask_worker runs, then it will never be cleared
from current_masked_alarm. This will prevent the alarm event from being
pushed even if the alarm is still active.
Fix this by recalculating current_masked_alarm immediately when enabling
or disabling alarms.
Fixes: d5c70627a7 ("iio: adc: Add Xilinx AMS driver")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: O'Griofa, Conall <conall.ogriofa@amd.com>
Tested-by: Erim, Salih <Salih.Erim@amd.com>
Acked-by: Erim, Salih <Salih.Erim@amd.com>
Link: https://patch.msgid.link/20250715002847.2035228-1-sean.anderson@linux.dev
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33d7ecbf69 upstream.
The ADF4350/1 features a programmable dual-modulus prescaler of 4/5 or 8/9.
When set to 4/5, the maximum RF frequency allowed is 3 GHz.
Therefore, when operating the ADF4351 above 3 GHz, this must be set to 8/9.
In this context not the RF output frequency is meant
- it's the VCO frequency.
Therefore move the prescaler selection after we derived the VCO frequency
from the desired RF output frequency.
This BUG may have caused PLL lock instabilities when operating the VCO at
the very high range close to 4.4 GHz.
Fixes: e31166f0fd ("iio: frequency: New driver for Analog Devices ADF4350/ADF4351 Wideband Synthesizers")
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250829-adf4350-fix-v2-1-0bf543ba797d@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
