Revert
99cf1fb58e ("x86/virt/sev: Drop WBINVD before setting MSR_AMD64_SYSCFG_SNP_EN").
Section 8.8 of the SNP spec says:
Before invoking SNP_INIT_EX with INIT_RMP set to 1, software must ensure
that no CPUs contain dirty cache lines for the memory containing the RMP.
Cachelines can be moved from cache to cache in a dirty state. The
wbinvd_on_all_cpus() before SNP_INIT_EX flushes the caches for each CPU, but
if the IPIs for WBINVD race with this dirty cacheline movement, it is possible
that they may not get flushed, violating the firmware requirement.
Doing wbinvd_on_all_cpus() before setting SNPEn is safer since the RMP
table is not yet in use.
[ Heroically bisected by Srikanth. ]
[ bp: Massage commit message. ]
Fixes: 99cf1fb58e ("x86/virt/sev: Drop WBINVD before setting MSR_AMD64_SYSCFG_SNP_EN")
Reported-by: Srikanth Aithal <Srikanth.Aithal@amd.com>
Signed-off-by: Tycho Andersen (AMD) <tycho@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Tested-by: Srikanth Aithal <Srikanth.Aithal@amd.com>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: <stable@kernel.org>
Link: https://patch.msgid.link/20260707150033.2364758-1-tycho@kernel.org
At the moment, concurrent writes from userspace and the kernel to the
console can trigger a race condition that results in an infinite loop of
the same messages printed over and over again. This is most likely to
happen during system startup or shutdown when the init system starts/stops
a large number of system services that interact with various kernel code.
When userspace writes to the TTY device, the driver initiates an
asynchronous DMA transfer and releases the port lock. At the same moment,
the kernel printk path might grab the port lock and re-configure the UART
controller for PIO, without waiting for the DMA operation to complete. It
seems like this collision results in zero progress being reported for the
DMA engine, so the same text is printed to the console over and over again.
For the kernel console, we want a reliable output path that will be
functional even during crashes etc. So rather than implementing complex
code to synchronize the kernel console write routines with the userspace
DMA write routines, simply disable DMA for the console UART instance.
Similar checks exist in many other serial drivers, e.g. 8250_port.c,
imx.c, sh-sci.c etc.
Cc: stable <stable@kernel.org>
Fixes: 3a878c430f ("tty: serial: msm: Add TX DMA support")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Acked-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://patch.msgid.link/20260706-serial-msm-console-dma-collision-v1-1-3179b8cb1d89@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tracepoints require that RCU is watching. To prevent them from being used
in places that RCU is not watching, the trace_##event() macro always
calls rcu_is_watching() even when the event is not enabled and warns if
RCU is not watching. This is to make sure a warning is triggered even if
the tracepoint is never enabled (as it is only a bug when it is).
It was noticed that tracepoints could be hidden within
trace_#event#_enabled() calls, which are used to do extra work for the
tracepoint only if the tracepoint is enabled. But this also can hide the
fact that a tracepoint is placed in a location that can be called when RCU
is not watching.
Commit 9764e731ef ("tracepoint: Add lockdep rcu_is_watching() check to
trace_##name##_enabled()") added a check to the trace_##event##_enabled()
macro to make sure RCU is watching when it is called to make sure not to
hide the bug of a tracepoint being called when RCU is not watching.
There is one case in the irq_disable tracepoint where it is within a
trace_irq_disable_enabled() block, but it checks if RCU is watching, and
if it isn't, it makes a call to ct_irq_enter() that makes RCU watch again.
But because trace_irq_disable_enabled() now checks if RCU is watching and
will trigger if it isn't. This is a false warning as the code within
the block handles this case.
Add a new internal macro __trace_##event##_enabled() that doesn't check if
RCU is watching, and convert the irq_enable/disable tracepoints over to
it.
Link: https://patch.msgid.link/20260701132744.6a7fc68b@robin
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/all/CAMuHMdXud_RpWag_hFqa2ByBGRxg6KnxGL1ObCWZrpTsk3TfAw@mail.gmail.com/
Fixes: 9764e731ef ("tracepoint: Add lockdep rcu_is_watching() check to trace_##name##_enabled()")
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
String event fields are not necessarily NUL-terminated, so the filter
predicate functions (filter_pred_string(), filter_pred_strloc() and
filter_pred_strrelloc()) pass the field length to the regex match
callbacks, and the length-aware matchers honour it.
regex_match_glob() was the exception: it ignored the length and called
glob_match(), which scans the string until it hits a NUL byte. Some
string fields are not NUL-terminated. One example is the dynamic char
array of the xfs_* namespace tracepoints, which is copied without a
trailing NUL. For such a field, glob matching reads past the end of
the event field, causing a KASAN slab-out-of-bounds read in
glob_match(), reached via regex_match_glob() and filter_match_preds()
from the xfs_lookup tracepoint.
Add a length-bounded glob_match_len() and use it from regex_match_glob()
so glob matching always stops at the field boundary. The matching loop
is factored into a shared helper so glob_match() keeps its behaviour.
Fixes: 60f1d5e3ba ("ftrace: Support full glob matching")
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/da1aaf125fc3b63320b0c540fd6afa7c3d5b4f1a.1782836943.git.hhhuang@smu.edu.sg
Reported-by: Yuan Tan <yuantan098@gmail.com>
Reported-by: Yifan Wu <yifanwucs@gmail.com>
Reported-by: Juefei Pu <tomapufckgml@gmail.com>
Reported-by: Zhengchuan Liang <zcliangcn@gmail.com>
Reported-by: Xin Liu <bird@lzu.edu.cn>
Assisted-by: Codex:GPT-5.4
Signed-off-by: Huihui Huang <hhhuang@smu.edu.sg>
Signed-off-by: Ren Wei <n05ec@lzu.edu.cn>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The trace events in drivers/ufs/core/ufs_trace.h were converted to take a
pointer to the hba structure as an argument for the tracepoint and then in
TP_printk() the printing of the dev_name from the ring buffer was
converted to using the dev dereferenced pointer from the hba saved
pointer.
This is not allowed as the TP_printk() is executed at the time the trace
event is read from /sys/kernel/tracing/trace file. That can happen
literally, seconds, minutes, hours, weeks, days, or even months later!
There is no guarantee that the hba pointer will still exist by the time it
is dereferenced when the "trace" file is read.
Instead, save the device name from the hba pointer at the time the
tracepoint is called and place it into the ring buffer event. Then the
TP_printk() can read the name directly from the ring buffer and remove the
possibility that it will read a freed pointer and crash the kernel.
This was detected when testing the trace event code that looks for
TP_printk() parameters doing illegal derferences[1]
[1] https://lore.kernel.org/all/20260630184836.74d477b6@gandalf.local.home/
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260630185412.283c26c5@gandalf.local.home
Fixes: 583e518e71 ("scsi: ufs: core: Add hba parameter to trace events")
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
func_set_flag() dereferences tr->current_trace_flags before verifying
that the current tracer is actually the function tracer. When the active
tracer has been switched away from "function" (e.g., to "wakeup_rt"),
tr->current_trace_flags can be NULL, leading to a NULL pointer
dereference and kernel crash.
The call chain that triggers this is:
trace_options_write()
-> __set_tracer_option()
-> trace->set_flag() /* func_set_flag */
In func_set_flag(), the first operation is:
if (!!set == !!(tr->current_trace_flags->val & bit))
This dereferences tr->current_trace_flags unconditionally. The safety
check that guards against a non-function tracer:
if (tr->current_trace != &function_trace)
return 0;
is placed *after* the dereference, which is too late.
This was observed with the following crash dump:
BUG: unable to handle page fault at 0000000000000000
RIP: func_set_flag+0xd
Call Trace:
__set_tracer_option+0x27
trace_options_write+0x75
vfs_write+0x12a
ksys_write+0x66
do_syscall_64+0x5b
RIP: ffffffff914c973d RSP: ff67ec88b01dfdf0 RFLAGS: 00010202
RAX: 0000000000000000 RBX: ff3a826e80354580 RCX: 0000000000000001
RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffffffff93918080
The disassembly confirms the fault:
func_set_flag+0: mov 0x1f08(%rdi), %rax ; RAX = tr->current_trace_flags = NULL
func_set_flag+13: mov (%rax), %eax ; page fault: dereference NULL
At the time of the crash:
tr->current_trace_flags = 0x0 (NULL)
tr->current_trace = wakeup_rt_tracer (not function_trace)
The scenario is that a process opens a function tracer option file (such
as "func_stack_trace"), then the current tracer is switched to another
tracer (e.g., "wakeup_rt"), which sets current_trace_flags to NULL. When
the process subsequently writes to the option file, func_set_flag() is
invoked and crashes on the NULL dereference.
Fix this by moving the current_trace check before the
current_trace_flags dereference, so that func_set_flag() returns early
when the function tracer is not active.
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260624061715.1445655-1-xiangzao@linux.alibaba.com
Fixes: 76680d0d28 ("tracing: Have function tracer define options per instance")
Signed-off-by: Yuanhe Shu <xiangzao@linux.alibaba.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Intel HD Audio defines Coefficient Index and Processing Coefficient as
separate audio widget controls in the Audio Widget Verb Definitions:
Coefficient Index selects the coefficient slot, while Processing
Coefficient accesses the value at the selected slot.
hda_reg_read_coef() selects the slot with AC_VERB_SET_COEF_INDEX, but
then uses AC_VERB_GET_COEF_INDEX for the value read. That reads back the
selected index instead of the coefficient value. hda_reg_write_coef()
has the same issue and builds the value write from AC_VERB_GET_COEF_INDEX
instead of AC_VERB_SET_PROC_COEF.
This only affects the regmap coefficient cache path used by codecs that
set codec->cache_coef. Direct coefficient helpers already use the normal
SET_COEF_INDEX followed by GET_PROC_COEF or SET_PROC_COEF sequence, which
is likely why this has not been noticed widely.
Use AC_VERB_GET_PROC_COEF for cached coefficient reads and
AC_VERB_SET_PROC_COEF for cached coefficient writes.
Fixes: 40ba66a702 ("ALSA: hda - Add cache support for COEF read/write")
Cc: stable@vger.kernel.org
Signed-off-by: Xu Rao <raoxu@uniontech.com>
Link: https://patch.msgid.link/DB9023BF2920BA99+20260707132419.1731342-1-raoxu@uniontech.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 8928e4a3be ("ring-buffer: Show persistent buffer dropped events
in trace_pipe file") split the "commit" variable in
ring_buffer_read_page() into "commit" (raw) and "size" (masked page
size), but the inner copy loop's terminator was changed to compare rpos
against "event_size" instead of "size".
rpos is the cumulative read offset within the page; event_size is the
length of the single event just copied. The loop thus breaks after the
first event, so only one event is copied per call. This regresses the
per-event memcpy path (partial reads, the active commit page, and
mapped/remote buffers) used by splice/trace_pipe_raw and mmap consumers
into a one-event-at-a-time read.
Compare rpos against the page size as the original code did.
Link: https://patch.msgid.link/20260616175538.111628-1-devnexen@gmail.com
Fixes: 8928e4a3be ("ring-buffer: Show persistent buffer dropped events in trace_pipe file")
Signed-off-by: David Carlier <devnexen@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The ASUS ROG Ally X (RC72LA, PCI SSID 0x1043:0x1eb3) leaves the combo
jack microphone pin (0x19) unconfigured, so a headset microphone is
neither detected nor captured. Only the internal microphone is
available.
Add a pin override that configures node 0x19 as an external headset
mic, the same way the original ROG Ally does. The headphone output
fixup chain is preserved, so speaker and headphone routing are
unchanged.
Signed-off-by: Matthew Schwartz <matthew.schwartz@linux.dev>
Link: https://patch.msgid.link/20260707005615.52889-2-matthew.schwartz@linux.dev
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ASUS ROG Ally X (RC72LA, PCI SSID 0x1043:0x1eb3) with an ALC294
codec produces no sound from the headphone jack, and unplugging the
headphones can leave the speakers muted too.
The device uses ALC287_FIXUP_TAS2781_I2C, which chains into the
ThinkPad fixup chain. alc285_fixup_thinkpad_x1_gen7() makes the
headphone (pin 0x21) and speaker (pin 0x17) share DAC 0x03. That is
correct for a ThinkPad, but here the shared DAC is exposed as a
"Line Out" control that defaults to zero, so the headphones stay
silent when plugged in.
Add a dedicated fixup chain for the Ally X that sets up the TAS2781
amplifier and the headset jack without the ThinkPad DAC sharing, and
routes the speaker to DAC 0x02 so the headphone and speaker get
independent DACs.
Also, fixup the wrong product code (it's RC72LA, not RCLA72).
Signed-off-by: Matthew Schwartz <matthew.schwartz@linux.dev>
Link: https://patch.msgid.link/20260707005615.52889-1-matthew.schwartz@linux.dev
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the descriptor's `ep_mem_offset` to calculate the start of the endpoint
memory access array and to comply with the FF-A spec instead of defaulting
to `sizeof(struct ffa_mem_region)`.
This requires moving `ffa_mem_region_additional_setup()` earlier in the setup
flow.
Also, add sanity checks to ensure the calculated descriptor offsets do not
exceed `max_fragsize`.
Fixes: 113580530e ("firmware: arm_ffa: Update memory descriptor to support v1.1 format")
Reviewed-by: Sudeep Holla <sudeep.holla@kernel.org>
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Signed-off-by: Sebastian Ene <sebastianene@google.com>
Link: https://patch.msgid.link/20260702103848.1647249-3-sebastianene@google.com
Signed-off-by: Marc Zyngier <maz@kernel.org>
Sashiko (locally) reports multiple out-of-bound issues in
ffa_setup_and_transmit:
1) Writing ep_mem_access->reserved can write out of bounds for FFA
versions < 1.2 as ffa_emad_size_get() returns 16 bytes in that case
while reserved has an offset of 24.
Instead of zeroing fields, memset the struct to zero first based on
the FFA version.
2) Make sure there is enough size to write constituents.
While at it, convert the only sizeof() in the driver that uses a
type instead of variable.
Reviewed-by: Sudeep Holla <sudeep.holla@kernel.org>
Fixes: 111a833dc5 ("firmware: arm_ffa: Set reserved/MBZ fields to zero in the memory descriptors")
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Signed-off-by: Sebastian Ene <sebastianene@google.com>
Link: https://patch.msgid.link/20260702103848.1647249-2-sebastianene@google.com
Signed-off-by: Marc Zyngier <maz@kernel.org>
Compiling RTLA 7.1.x with GCC 16 and uClibc as standard library fails
with these errors:
src/common.c: In function ‘set_signals’:
src/common.c:40:17: error: implicit declaration of function ‘alarm’ [-Wimplicit-function-declaration]
40 | alarm(params->duration);
| ^~~~~
src/common.c: In function ‘common_apply_config’:
src/common.c:187:44: error: implicit declaration of function ‘getpid’; did you mean ‘getpt’? [-Wimplicit-function-declaration]
187 | retval = sched_setaffinity(getpid(), sizeof(params->hk_cpu_set),
| ^~~~~~
| getpt
In file included from src/common.c:9:
src/common.c: In function ‘run_tool’:
src/common.c:262:19: error: implicit declaration of function ‘sysconf’; did you mean ‘sscanf’? [-Wimplicit-function-declaration]
262 | nr_cpus = get_nprocs_conf();
| ^~~~~~~~~~~~~~~
src/common.c:262:19: error: ‘_SC_NPROCESSORS_CONF’ undeclared (first use in this function)
262 | nr_cpus = get_nprocs_conf();
| ^~~~~~~~~~~~~~~
src/common.c:262:19: note: each undeclared identifier is reported only once for each function it appears in
src/common.c:370:17: error: implicit declaration of function ‘sleep’ [-Wimplicit-function-declaration]
370 | sleep(1);
| ^~~~~
Restore the missing unistd.h include.
Fixes: 115b06a008 ("tools/rtla: Consolidate nr_cpus usage across all tools")
Signed-off-by: Andreas Ziegler <br025@umbiko.net>
Link: https://lore.kernel.org/r/20260624033342.129970-1-br025@umbiko.net
[ capital letter in patch subject, remove EOL after Fixes ]
Signed-off-by: Tomas Glozar <tglozar@redhat.com>
The client cap is currently advertised unconditionally, even for drivers
that do not support plane color pipelines. If clients supporting the latter,
like Wayland compositors or tools like drm_info, enable the client cap on
such drivers they will be left without both color pipeline and the legacy
properties COLOR_ENCODING and COLOR_RANGE, effectively breaking YUV->RGB
conversion support.
Prevent that by only marking the cap supported if there are actually planes
with color pipelines.
Note: while the color pipeline replacement for the legacy properties is
still under review (1), we can assume that it will work as a drop-in
replacement. That means any plane on any hardware currently supporting
the legacy properties will be able to offer a functionally equal color
pipeline and there will be no technical reason keep using the legacy
properties if both the driver and the client support the new API.
[1] https://lore.kernel.org/dri-devel/20260623164812.81110-1-harry.wentland@amd.com/
Signed-off-by: Robert Mader <robert.mader@collabora.com>
Reviewed-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Fixes: 179ab8e7d7 ("drm/colorop: Introduce DRM_CLIENT_CAP_PLANE_COLOR_PIPELINE")
Link: https://patch.msgid.link/20260703073230.19982-1-robert.mader@collabora.com
Suggested-by: Maarten Lankhorst <dev@lankhorst.se>
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
GPIO interrupts may retain stale state across warm reboots when
peripherals remain powered. If a GPIO line is not explicitly
configured for interrupts, this can result in interrupt storms
due to missing handlers.
Fix this by ensuring all interrupts are masked and disabled at
hardware initialization time via the init_hw() callback. Pending
interrupts are also cleared to start from a known-safe state.
Interrupts will be unmasked only when explicitly configured by
userspace or kernel drivers.
Signed-off-by: Liang Hao <haohlliang@gmail.com>
Link: https://patch.msgid.link/20260705074759.47863-1-haohlliang@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
GPIO consumers such as gpio-keys can enable IRQ wake and adjust the wake
trigger type from their suspend callbacks. If the DWAPB controller suspends
first, masking interrupts and disabling its clocks in the normal suspend
phase prevents that late wake configuration from reliably reaching the
hardware. Systems with real DWAPB bus clocks then fail to wake from s2idle
through GPIO keys.
Save the register context in the normal suspend callback, but defer IRQ
masking and clock gating until suspend_noirq. At that point all consumers
have finished configuring wake IRQs, so keep the clocks enabled when wake
lines are armed and only gate them when no wake source is active.
Resume_noirq reenables clocks, if they were gated, before the normal resume
path restores registers.
Propagate wake requests to the parent irqchip while keeping the local wake
mask in sync with failures.
Fixes: 6437c7ba69 ("gpio: dwapb: Add wakeup source support")
Signed-off-by: Jia Wang <wangjia@ultrarisc.com>
Link: https://patch.msgid.link/20260702-gpio-dwapb-wakeup-v2-1-203f2f33429f@ultrarisc.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
cfg80211_is_element_inherited() reads the first data octet of the
candidate element (id = elem->data[0]) to look it up in an extension
non-inheritance list. It does so after testing elem->id, but without
verifying that the element actually has a data octet. A zero-length
extension element (WLAN_EID_EXTENSION with length 0) therefore makes it
read one octet past the end of the element.
_ieee802_11_parse_elems_full() runs this check for every element of a
frame once a non-inheritance context exists -- e.g. while parsing a
per-STA profile of a Multi-Link element in a (re)association response,
or a non-transmitted BSS profile -- so a crafted frame from an AP can
trigger a one-octet slab-out-of-bounds read during element parsing:
BUG: KASAN: slab-out-of-bounds in cfg80211_is_element_inherited
Read of size 1 ... in net/wireless/scan.c
Return early (treat the element as inherited) when an extension element
carries no data, mirroring the existing handling of empty ID lists.
The bug was found by fuzzing ieee802_11_parse_elems_full() under KASAN.
Fixes: f7dacfb114 ("cfg80211: support non-inheritance element")
Signed-off-by: HE WEI (ギカク) <skyexpoc@gmail.com>
Link: https://patch.msgid.link/20260707094828.16465-1-skyexpoc@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Three IE/attribute parsing functions have missing bounds checks.
rtw_get_sec_ie() and rtw_get_wapi_ie() iterate over a raw IE buffer
without verifying that the header bytes (tag + length) are within the
remaining buffer before reading them. Additionally, rtw_get_sec_ie()
compares the 4-byte WPA OUI at cnt+2 without checking that at least
6 bytes remain, and rtw_get_wapi_ie() compares a 4-byte WAPI OUI at
cnt+6 without checking that at least 10 bytes remain.
rtw_get_wps_attr() reads wps_ie[0] and wps_ie+2 unconditionally at
entry, before verifying that wps_ielen is large enough to contain
the 6-byte WPS IE header (element_id + length + 4-byte OUI). Inside
the attribute loop, get_unaligned_be16() is called on attr_ptr and
attr_ptr+2 without checking that 4 bytes remain in the buffer.
Add a cnt+2 bounds check before each loop body in rtw_get_sec_ie()
and rtw_get_wapi_ie(), guard each multi-byte comparison with a minimum
IE length requirement, add a wps_ielen < 6 early return in
rtw_get_wps_attr(), and add a 4-byte bounds check in its inner loop.
Fixes: 554c0a3abf ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Alexandru Hossu <hossu.alexandru@gmail.com>
Link: https://patch.msgid.link/20260522004531.1038924-8-hossu.alexandru@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The loop in is_ap_in_tkip() iterates over IEs without verifying that
enough bytes remain before dereferencing the IE header or its payload:
- pIE->element_id and pIE->length are read without checking that
i + sizeof(*pIE) <= ie_length, so a truncated IE at the end of the
buffer causes an OOB read.
- For WLAN_EID_VENDOR_SPECIFIC the code compares pIE->data + 12,
which requires pIE->length >= 16. For WLAN_EID_RSN it compares
pIE->data + 8, requiring pIE->length >= 12. Neither requirement
is checked.
Add the missing IE header and payload bounds checks and guard each
data access with an explicit pIE->length minimum, matching the
pattern established in update_beacon_info().
Fixes: 554c0a3abf ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Alexandru Hossu <hossu.alexandru@gmail.com>
Link: https://patch.msgid.link/20260522004531.1038924-7-hossu.alexandru@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IE parsing loop in OnAssocRsp() advances by (pIE->length + 2) each
iteration but only guards on i < pkt_len. When a malicious AP sends an
AssocResponse whose last IE has only one byte remaining in the frame
(the element_id byte lands at pkt_len-1), the loop reads pIE->length
from pframe[pkt_len], which is one byte past the allocated receive buffer.
Additionally, even when the header bytes are in bounds, pIE->length
itself can extend the data window beyond pkt_len, silently passing a
truncated IE to the handler functions.
Add two guards at the top of the loop body:
1. Break if fewer than sizeof(*pIE) bytes remain (can't read header).
2. Break if the IE's declared data extends past pkt_len.
Fixes: 554c0a3abf ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Alexandru Hossu <hossu.alexandru@gmail.com>
Reviewed-by: Luka Gejak <luka.gejak@linux.dev>
Link: https://patch.msgid.link/20260522004531.1038924-6-hossu.alexandru@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HT_caps_handler() iterates pIE->length bytes and writes into
HT_caps.u.HT_cap[], which is a fixed 26-byte array (sizeof struct
HT_caps_element). Because pIE->length is a raw u8 from an over-the-air
802.11 AssocResponse frame and is never validated, a malicious AP can
set it up to 255, causing up to 229 bytes of out-of-bounds writes into
adjacent fields of struct mlme_ext_info.
Truncate the iteration count to the size of HT_caps.u.HT_cap using
umin() so that data from a longer-than-expected IE is silently ignored
rather than written out of bounds, preserving interoperability with APs
that pad the element. An early return on oversized IEs was considered
but rejected: it would bypass the pmlmeinfo->HT_caps_enable = 1
assignment that precedes the loop, silently disabling HT mode for APs
that append extra bytes to the HT Capabilities IE.
Fixes: 554c0a3abf ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Alexandru Hossu <hossu.alexandru@gmail.com>
Reviewed-by: Luka Gejak <luka.gejak@linux.dev>
Link: https://patch.msgid.link/20260522004531.1038924-5-hossu.alexandru@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
supplicant_ie is a 256-byte array in struct security_priv. The WPA and
WPA2 IE copy paths use:
memcpy(padapter->securitypriv.supplicant_ie, &pwpa[0], wpa_ielen + 2);
where wpa_ielen is the raw IE length field (u8, 0-255). When a local user
supplies a connect request via nl80211 with a crafted WPA IE of length 255,
wpa_ielen + 2 equals 257, overflowing the 256-byte buffer by one byte into
the adjacent last_mic_err_time field.
rtw_parse_wpa_ie() does not prevent this: its length consistency check
compares *(wpa_ie+1) against (u8)(wpa_ie_len-2), which is (u8)(255) == 255
when wpa_ie_len = 257, so the check passes silently.
Add explicit bounds checks for both the WPA and WPA2 paths before the
memcpy, rejecting any IE whose total size (wpa_ielen + 2) exceeds the
supplicant_ie buffer.
Fixes: 554c0a3abf ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable <stable@kernel.org>
Reviewed-by: Luka Gejak <luka.gejak@linux.dev>
Signed-off-by: Alexandru Hossu <hossu.alexandru@gmail.com>
Link: https://patch.msgid.link/20260522004531.1038924-4-hossu.alexandru@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two IE parsing loops are missing the header bounds checks before they
dereference pIE->length:
- issue_assocreq() walks pmlmeinfo->network.ies to build the
association request. If the stored IE data ends with only an
element_id byte and no length byte, pIE->length is read one byte
past the end of the buffer.
- join_cmd_hdl() walks pnetwork->ies during station join and has
the same problem under the same conditions.
Both buffers are filled from AP beacon and probe-response frames, so a
malicious AP that sends a truncated final IE can trigger the issue.
Apply the two-guard pattern established in update_beacon_info():
1. Break if fewer than sizeof(*pIE) bytes remain.
2. Break if the IE's declared data extends past the buffer end.
Fixes: 554c0a3abf ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable <stable@kernel.org>
Reviewed-by: Luka Gejak <luka.gejak@linux.dev>
Signed-off-by: Alexandru Hossu <hossu.alexandru@gmail.com>
Link: https://patch.msgid.link/20260522004531.1038924-3-hossu.alexandru@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IE parsing loop in update_beacon_info() advances by
(pIE->length + 2) each iteration but only guards on i < len.
When a malicious AP sends a Beacon whose last IE has only one byte
remaining in the frame (the element_id byte lands at len-1), the loop
reads pIE->length from one byte past the allocated receive buffer.
Additionally, even when the header bytes are in bounds, pIE->length
itself can extend the data window beyond len, passing a truncated IE
to the handler functions.
Add two guards at the top of the loop body:
1. Break if fewer than sizeof(*pIE) bytes remain (can't read header).
2. Break if the IE's declared data extends past len.
Also replace i += (pIE->length + 2) with i += sizeof(*pIE) + pIE->length
for consistency with the sizeof(*pIE) guards added above.
Fixes: 554c0a3abf ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable <stable@kernel.org>
Reviewed-by: Luka Gejak <luka.gejak@linux.dev>
Signed-off-by: Alexandru Hossu <hossu.alexandru@gmail.com>
Link: https://patch.msgid.link/20260522004531.1038924-2-hossu.alexandru@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OnAuth() has two bugs in the shared-key authentication path.
When the Privacy bit is set, rtw_wep_decrypt() is called without
verifying that the frame is long enough to contain a valid WEP IV and
ICV. Inside rtw_wep_decrypt(), length is computed as:
length = len - WLAN_HDR_A3_LEN - iv_len
and then passed as (length - 4) to crc32_le(). If len is less than
WLAN_HDR_A3_LEN + iv_len + icv_len (32 bytes), length - 4 is negative
and, after the implicit cast to size_t, causes crc32_le() to read far
beyond the frame buffer. Add a minimum length check before accessing
the IV field and calling the decryption path.
When processing a seq=3 response, rtw_get_ie() stores the Challenge
Text IE length in ie_len, but the subsequent memcmp() always reads 128
bytes regardless of ie_len. IEEE 802.11 mandates a challenge text of
exactly 128 bytes; reject any IE whose length field differs, matching
the check already applied to OnAuthClient().
Fixes: 554c0a3abf ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Alexandru Hossu <hossu.alexandru@gmail.com>
Link: https://patch.msgid.link/20260522004605.1039209-1-hossu.alexandru@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tsi148_probe() allocates a location monitor resource and links it into
tsi148_bridge->lm_resources. The probe error path frees this list, but
tsi148_remove() only frees the dma, slave and master resource lists, so
the location monitor resource is leaked on device unbind or module
unload.
Free the lm_resources list in tsi148_remove() as well, before
tsi148_bridge is freed.
Fixes: d22b8ed9a3 ("Staging: vme: add Tundra TSI148 VME-PCI Bridge driver")
Cc: stable <stable@kernel.org>
Cc: Martyn Welch <martyn@welchs.me.uk>
Assisted-by: Claude:claude-fable-5
Signed-off-by: Hao-Qun Huang <alvinhuang0603@gmail.com>
Link: https://patch.msgid.link/20260704065817.403111-2-alvinhuang0603@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fake_init() allocates a location monitor resource and links it into
fake_bridge->lm_resources. The init error path frees this list, but
fake_exit() only frees the slave and master resource lists. Loading
and unloading the module therefore triggers a kmemleak warning:
unreferenced object 0xffff8b8b82aebe40 (size 64):
comm "init", pid 1, jiffies 4294894572
backtrace (crc c1e013ef):
kmemleak_alloc+0x4e/0x90
__kmalloc_cache_noprof+0x338/0x430
0xffffffffc0602246
do_one_initcall+0x4f/0x320
do_init_module+0x68/0x270
load_module+0x2a3b/0x2d90
Free the lm_resources list in fake_exit() as well, before fake_bridge
is freed.
Fixes: 658bcdae9c ("vme: Adding Fake VME driver")
Cc: stable <stable@kernel.org>
Cc: Martyn Welch <martyn@welchs.me.uk>
Assisted-by: Claude:claude-fable-5
Signed-off-by: Hao-Qun Huang <alvinhuang0603@gmail.com>
Link: https://patch.msgid.link/20260704065817.403111-1-alvinhuang0603@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SLAVE-path helpers buffer_to_user() and buffer_from_user() copy
'count' bytes into/out of the fixed-size kern_buf (size_buf ==
PCI_BUF_SIZE == 0x20000, 128 KiB) using *ppos as the offset, without
bounding *ppos + count against size_buf.
vme_user_write()/vme_user_read() only clamp count to the VME window size
(image_size = vme_get_size(resource)), which VME_SET_SLAVE sets from the
user-supplied slave.size -- validated against the VME address space (up
to VME_A32_MAX = 4 GiB), not against PCI_BUF_SIZE. When the window
exceeds 128 KiB, a write()/read() copies past the kern_buf allocation.
Clamp count against size_buf in both helpers, with an early return when
*ppos is already at/after the buffer end. *ppos is >= 0 here (the caller
rejects negative offsets), so size_buf - *ppos cannot wrap. This mirrors
the existing clamp in the MASTER-path helpers resource_to_user() /
resource_from_user(), and matches the read()/write() convention of a
short transfer at end-of-buffer.
Found by static analysis (CodeQL taint tracking + CBMC bounded model
checking) and confirmed dynamically under KASAN with the vme_fake bridge:
BUG: KASAN: slab-out-of-bounds in _copy_from_user+0x2d/0x80
Write of size 262144 at addr ffff888004100000 by task trigger/68
_copy_from_user+0x2d/0x80
vme_user_write+0x13e/0x240 [vme_user]
vfs_write+0x1b8/0x7a0
ksys_write+0xb8/0x150
Fixes: f00a86d98a ("Staging: vme: add VME userspace driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Michael Tautschnig <tautschn@amazon.com>
Link: https://patch.msgid.link/20260618114709.72499-1-tautschn@amazon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit bc4df274dc ("staging: rtl8723bs: update _rtw_pktfile_read() to
return error codes") changed _rtw_pktfile_read() to fail when the caller
asks for more bytes than remain in the packet:
if (rtw_remainder_len(pfile) < rlen)
return -EINVAL;
That breaks the assumption made by the data TX path. In
rtw_xmitframe_coalesce() (core/rtw_xmit.c) the per-fragment copy is
issued with the full fragment length, mpdu_len, which is derived from
pxmitpriv->frag_len (~2300 bytes), and the code relies on the historical
behaviour of copying only what is left and returning the number of bytes
actually copied:
mem_sz = _rtw_pktfile_read(&pktfile, pframe, mpdu_len);
if (mem_sz < 0)
return mem_sz;
So for every outbound packet smaller than the fragmentation threshold -
i.e. essentially all normal traffic, including the EAPOL frames of the
WPA 4-way handshake and DHCP - rlen is larger than the bytes remaining,
_rtw_pktfile_read() returns -EINVAL, rtw_xmitframe_coalesce() aborts, and
the frame is dropped before it is queued to the hardware. The driver
floods the log with:
rtl8723bs ...: xmit_xmitframes: coalesce failed with error -22
Management frames (authentication/association) use a different path and
still go out, so the interface scans and associates, but no data frame is
ever transmitted. The 4-way handshake therefore never completes and
wpa_supplicant misreports it as:
WPA: 4-Way Handshake failed - pre-shared key may be incorrect
AP mode is unaffected. The net effect is that the chip is unusable in
station mode on any kernel carrying the offending commit.
This was confirmed with a wpa_supplicant -dd trace on an RTL8723BS SDIO
adapter (Bay Trail): message 1/4 is received and the PTK is derived, but
each "Sending EAPOL-Key 2/4" coincides 1:1 with a "coalesce failed with
error -22", so message 2/4 never reaches the AP, which keeps retrying
message 1/4 until the handshake times out.
Restore the original semantics: clamp the requested length to the bytes
remaining in the packet and return that length. The skb_copy_bits()
error path is kept, so genuine copy failures are still propagated.
Fixes: bc4df274dc ("staging: rtl8723bs: update _rtw_pktfile_read() to return error codes")
Cc: stable <stable@kernel.org>
Tested-by: Christopher Mackle <christophermackle01@gmail.com>
Signed-off-by: Christopher Mackle <christophermackle01@gmail.com>
Link: https://patch.msgid.link/20260620013916.7148-1-christophermackle01@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hardware VLAN filter (RFE_CTL_VLAN_FILTER_) drops VLAN-tagged frames
whose VID has not been registered via lan78xx_vlan_rx_add_vid(). It is
left enabled in promiscuous mode, so packet capture (e.g. tcpdump or
Wireshark) does not see tagged frames for unregistered VIDs.
Clear the filter while the interface is promiscuous and restore it from
NETIF_F_HW_VLAN_CTAG_FILTER otherwise. Enforce the same condition in
lan78xx_set_features() so netdev_update_features() cannot re-enable the
filter while promiscuous.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Enrico Pozzobon <enrico.pozzobon@dissecto.com>
Reviewed-by: Nicolai Buchwitz <nb@tipi-net.de>
Link: https://patch.msgid.link/20260701-lan78xx-vlan-promisc-v3-1-232266d32743@dissecto.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Harden the check for the constituent memory region page alignment
to prevent over-sharing when the negotiated FFA_PAGE_SIZE size is
smaller than the system PAGE_SIZE.
At the moment we only check that the size of the range is page
aligned, and truncate the address to the page boundary which can
annotate more memory than needed as being used by the FF-A.
Fixes: 4360900017 ("KVM: arm64: Handle FFA_MEM_SHARE calls from the host")
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Reviewed-by: Vincent Donnefort <vdonnefort@google.com>
Signed-off-by: Sebastian Ene <sebastianene@google.com>
Link: https://patch.msgid.link/20260702103848.1647249-6-sebastianene@google.com
Signed-off-by: Marc Zyngier <maz@kernel.org>
Prevent the pKVM hypervisor from making assumptions that the
endpoint memory access descriptor (EMAD) comes right after the
FF-A memory region header.
Prior to FF-A version 1.1 the header of the memory region
didn't contain an offset to the endpoint memory access descriptor.
The layout of a memory transaction looks like this from 1.1 onward:
Type | Field name | Offset
[ Header | ffa_mem_region | 0
EMAD 1 | ffa_mem_region_attributes) | ffa_mem_region.ep_mem_offset
]
Verify that the offset to the first endpoint memory access descriptor
is within the mailbox buffer bounds.
Also, fix one hardcoded sizeof(struct ffa_mem_region_attributes) that
should be replaced ffa_emad_size_get() for compatibility with FFA v1.0.
Fixes: 42fb33dde4 ("KVM: arm64: Use FF-A 1.1 with pKVM")
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Signed-off-by: Sebastian Ene <sebastianene@google.com>
Reviewed-by: Vincent Donnefort <vdonnefort@google.com>
Link: https://patch.msgid.link/20260702103848.1647249-5-sebastianene@google.com
Signed-off-by: Marc Zyngier <maz@kernel.org>
Sashiko (locally) reports out of bound write possiblity if SPMD
returns an invalid data.
While SPMD is considered trusted, pKVM does some basic checks,
for offset to be less than or equal len.
However, that is incorrect as even if the offset is smaller than
len pKVM can still access out of bound memory in the next
ffa_host_unshare_ranges().
Split this check into 2:
1- Check that the fixed portion of the descriptor fits.
2- After getting reg, check the variable array size addr_range_cnt
fits.
Also, drop the WARN_ONs as that will panic the kernel and in the
next checks there are no WARNs, so that makes it consistent.
Fixes: 0a9f15fd56 ("KVM: arm64: pkvm: Add support for fragmented FF-A descriptors")
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Reviewed-by: Vincent Donnefort <vdonnefort@google.com>
Signed-off-by: Sebastian Ene <sebastianene@google.com>
Link: https://patch.msgid.link/20260702103848.1647249-4-sebastianene@google.com
Signed-off-by: Marc Zyngier <maz@kernel.org>
When a device is destroyed under RTNL, ip_mc_destroy_dev() iterates through
the multicast list and calls ip_ma_put() on each membership, scheduling
them for RCU reclamation. However, they are not unlinked from the device's
multicast hash table (mc_hash).
Since the device remains published in dev->ip_ptr until after
ip_mc_destroy_dev() completes, concurrent RCU readers traversing mc_hash
can still locate and access the multicast group after its refcount is
decremented. If the RCU callback runs and frees the group while a reader is
accessing it, a use-after-free occurs.
Fix this by unlinking the multicast group from mc_hash using
ip_mc_hash_remove() before scheduling it for reclamation.
BUG: KASAN: slab-use-after-free in ip_check_mc_rcu+0x149/0x3f0
Read of size 4 at addr ffff888009bf1408 by task mausezahn/2276
Call Trace:
<IRQ>
dump_stack_lvl+0x67/0x90
print_report+0x175/0x7c0
kasan_report+0x147/0x180
ip_check_mc_rcu+0x149/0x3f0
udp_v4_early_demux+0x36d/0x12d0
ip_rcv_finish_core+0xb8b/0x1390
ip_rcv_finish+0x54/0x120
NF_HOOK+0x213/0x2b0
__netif_receive_skb+0x126/0x340
process_backlog+0x4f2/0xf00
__napi_poll+0x92/0x2c0
net_rx_action+0x583/0xc60
handle_softirqs+0x236/0x7f0
do_softirq+0x57/0x80
</IRQ>
Allocated by task 2239:
kasan_save_track+0x3e/0x80
__kasan_kmalloc+0x72/0x90
____ip_mc_inc_group+0x31a/0xa40
__ip_mc_join_group+0x334/0x3f0
do_ip_setsockopt+0x16fa/0x2010
ip_setsockopt+0x3f/0x90
do_sock_setsockopt+0x1ad/0x300
Freed by task 0:
kasan_save_track+0x3e/0x80
kasan_save_free_info+0x40/0x50
__kasan_slab_free+0x3a/0x60
__rcu_free_sheaf_prepare+0xd4/0x220
rcu_free_sheaf+0x36/0x190
rcu_core+0x8d9/0x12f0
handle_softirqs+0x236/0x7f0
Fixes: e989707135 ("igmp: hash a hash table to speedup ip_check_mc_rcu()")
Cc: stable@vger.kernel.org
Signed-off-by: Yuyang Huang <yuyanghuang@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260701235014.73505-1-yuyanghuang@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The PF SR-IOV enable path caches VF pci_dev pointers in
dpiring_to_vfpcidev_lut[] by iterating with pci_get_device(). Those
entries do not own a reference, because the iterator drops the previous
device reference on each step. The cached pointer is then dereferenced
later when handling OCTEON_VF_FLR_REQUEST.
Replace the cached VF mapping with runtime lookup on the mailbox DPI
ring: derive the VF index from q_no, resolve the VF via exported PCI
IOV helpers, validate it with the PF pointer and VF ID, then issue
pcie_flr() and drop the reference with pci_dev_put(). Remove the
unused VF lookup table initialization and cleanup.
Fixes: ca6139ffc6 ("liquidio CN23XX: sysfs VF config support")
Fixes: 8c978d0592 ("liquidio CN23XX: Mailbox support")
Signed-off-by: Yuho Choi <dbgh9129@gmail.com>
Link: https://patch.msgid.link/20260701040847.1897845-1-dbgh9129@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The rnpgbe mailbox exchanges data through 32-bit MMIO registers in
little-endian wire format. The original code had two problems:
1. FW structs (with __le16/__le32 fields) were cast to (u32 *)
before reaching the mailbox transport, hiding the endian
annotations from sparse.
2. No cpu_to_le32()/le32_to_cpu() conversion was done between
CPU-endian MMIO values and the little-endian payload, causing
data corruption on big-endian systems.
Fix by adding the missing byte-order conversions in the transport
layer and introducing union wrappers (mbx_fw_cmd_req_u,
mbx_fw_cmd_reply_u) that overlay each FW struct with a __le32
dwords[] array. Callers fill named fields using cpu_to_le16/32(),
then pass dwords[] to the transport, which now takes explicit
__le32 * instead of u32 *. This eliminates all pointer casts on
the mailbox data path and lets sparse verify the conversions.
Fixes: 4543534c3e ("net: rnpgbe: Add basic mbx ops support")
Signed-off-by: Dong Yibo <dong100@mucse.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260701032208.1843156-2-dong100@mucse.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
brcmf_notify_auth_frame_rx() takes the frame length from the firmware
event and copies the frame body with the management header offset
subtracted:
u32 mgmt_frame_len = e->datalen - sizeof(struct brcmf_rx_mgmt_data);
...
memcpy(&mgmt_frame->u, frame,
mgmt_frame_len - offsetof(struct ieee80211_mgmt, u));
The only length check is e->datalen >= sizeof(*rxframe), so mgmt_frame_len
can be anything from 0 up. offsetof(struct ieee80211_mgmt, u) is 24. When
mgmt_frame_len is below that, the subtraction wraps as an unsigned value to
a huge length. The memcpy then runs far past the kzalloc'd buffer. A
malicious or malfunctioning AP can make the frame short during the
external SAE auth exchange, so this is a remotely triggered heap overflow.
Reject frames shorter than the management header offset before the copy.
Fixes: 66f909308a ("wifi: brcmfmac: cyw: support external SAE authentication in station mode")
Link: https://lore.kernel.org/r/178214417708.2368577.16740907093694208834@maoyixie.com
Cc: stable@vger.kernel.org
Co-developed-by: Kaixuan Li <kaixuan.li@ntu.edu.sg>
Signed-off-by: Kaixuan Li <kaixuan.li@ntu.edu.sg>
Signed-off-by: Maoyi Xie <maoyixie.tju@gmail.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://patch.msgid.link/20260627131313.3878893-1-maoyixie.tju@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A peer may send a zero-length TLS application_data record; TLS 1.3
explicitly permits these as a traffic-analysis countermeasure (RFC
8446, Section 5.1). After decryption such a record has full_len ==
0. tls_sw_read_sock() hands it to the read_actor, which has no
payload to consume and returns zero. The loop treats a zero return
as backpressure (used <= 0), requeues the skb at the head of
rx_list, and stops. rx_list is serviced head-first on the next
call, so the empty record is dequeued, fails the same way, and is
requeued again; every later record on the connection is blocked
behind it.
tls_sw_recvmsg() does not stall on this: a zero-length data record
copies nothing and falls through to consume_skb(). Mirror that in
the read_sock() path by recognizing an empty data record before
the actor runs, consuming it, and continuing.
Fixes: 662fbcec32 ("net/tls: implement ->read_sock()")
Signed-off-by: Chuck Lever <cel@kernel.org>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://patch.msgid.link/20260630191551.875664-1-cel@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
brcmf_sdio_probe() stores the newly allocated bus in sdiodev->bus before
allocating the ordered workqueue. If that allocation fails, the function
jumps to fail and calls brcmf_sdio_remove().
brcmf_sdio_remove() unconditionally cancels bus->datawork. Initialize the
work item before the first failure path that can reach brcmf_sdio_remove(),
so the cleanup path always observes a valid work object.
This issue was found by our static analysis tool and then confirmed by
manual review of the probe error path and the remove-time work drain. The
problem pattern is an early setup failure that reaches a cleanup helper
which cancels an embedded work item before its initializer has run.
A QEMU PoC forced alloc_ordered_workqueue() to fail at the same point in
brcmf_sdio_probe(), before INIT_WORK(&bus->datawork) is reached. The
resulting fail path calls brcmf_sdio_remove(), and DEBUG_OBJECTS reports
the invalid work drain with brcmf_sdio_probe() and brcmf_sdio_remove() in
the stack.
Fixes: 9982464379 ("brcmfmac: make sdio suspend wait for threads to freeze")
Signed-off-by: Runyu Xiao <runyu.xiao@seu.edu.cn>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://patch.msgid.link/20260619064401.1048976-1-runyu.xiao@seu.edu.cn
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On error, xlog_recover_reorder_trans() splices the leftover sort_list
items back to trans->r_itemq inside the loop before breaking out. The
loop tail already splices the per-fate lists back, so do sort_list there
too, guarded by the assert that used to sit after the loop.
No functional change. It drops the duplicated splice so the next patch
can add another error case without repeating it.
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Weiming Shi <bestswngs@gmail.com>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
The item type passed to ITEM_TYPE() comes from the on-disk log, so a
fuzzed or crafted image can reach the "unrecognized type" path in
xlog_recover_reorder_trans() and trip its ASSERT(0) on a
CONFIG_XFS_DEBUG kernel. The -EFSCORRUPTED return handles it fine; drop
the assert.
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Weiming Shi <bestswngs@gmail.com>
Reviewed-by: "Darrick J. Wong" <djwong@kernel.org>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
cfg80211_rx_assoc_resp() initialises the status and response-IE fields
of cfg80211_connect_resp_params from the management frame before
proving that the frame is long enough for those offsets. S1G and
regular association responses also have different IE offsets, but the
S1G path only patched resp_ie after the unsafe initialiser had already
run.
Defer resp_ie, resp_ie_len, and status to after the link-iteration
loop. Use a bool to remember whether the frame is S1G, then validate
the appropriate minimum length and set all three fields in a single
if/else block. Funnel short-frame and SME-reject cleanup through a
shared free_bss label for the abandon paths.
Assisted-by: Codex:gpt-5.5
Assisted-by: Claude:claude-opus-4.8
Signed-off-by: Zhao Li <enderaoelyther@gmail.com>
Link: https://patch.msgid.link/20260707025336.22557-2-enderaoelyther@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tycho Andersen (AMD)
Stephan Gerhold
Tapio Reijonen
Mario Limonciello
Steven Rostedt
Huihui Huang
Yuanhe Shu
Yudistira Putra
Ben Dooks
Xu Rao
David Carlier
Takashi Iwai
Longlong Xia
Matthew Schwartz
Sebastian Ene
Mostafa Saleh
Andreas Ziegler
Robert Mader
Liang Hao
Jia Wang
Christian König
HE WEI (ギカク)
Alexandru Hossu
Hao-Qun Huang
Michael Tautschnig
Christopher Mackle
Enrico Pozzobon
Yuyang Huang
Yuho Choi
Dong Yibo
Maoyi Xie
Chuck Lever
Runyu Xiao
Weiming Shi
Zhao Li