The test in stmmac_xmit() to see whether we should pass the skbuff to
stmmac_tso_xmit() is more complex than it needs to be. This test can
be simplified by storing the mask of GSO types that we will pass, and
setting it according to the enabled features.
Note that "tso" is a mis-nomer since commit b776620651 ("net:
stmmac: Implement UDP Segmentation Offload"). Also note that this
commit controls both via the TSO feature. We preserve this behaviour
in this commit.
Also, this commit unconditionally accessed skb_shinfo(skb)->gso_type
for all frames, even when skb_is_gso() was false. This access is
eliminated.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1w7ptj-0000000Eatb-11zK@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a check in .ndo_features_check() to indicate whether hardware
checksum can be performed on the skbuff. Where hardware checksum is
not supported - either because the channel does not support Tx COE
or the skb isn't suitable (stmmac uses a tighter test than
can_checksum_protocol()) we also need to disable TSO, which will be
done by harmonize_features() in net/core/dev.c
This fixes a bug where a channel which has COE disabled may still
receive TSO skbuffs.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1w7pte-0000000EatU-0ILt@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
stmmac_tso_xmit() checks whether the skbuff is trying to offload
vlan tag insertion to hardware, which from the comment in the code
appears to be buggy when the TSO feature is used.
Rather than stmmac_tso_xmit() inserting the VLAN tag, handle this
in stmmac_features_check() which will then use core net code to
handle this. See net/core/dev.c::validate_xmit_skb()
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1w7ptY-0000000EatO-42Qv@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to the STM32MP151 documentation which covers dwmac v4.2, the
hardware TSO feature can handle header lengths up to a maximum of 1023
bytes.
Add a .ndo_features_check() method implementation to check the header
length meets these requirements, otherwise fall back to software GSO.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1w7ptO-0000000EatC-39il@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to the STM32MP25xx manual, which is dwmac v5.3, TBS (time
based scheduling) is not permitted for channels which have hardware
TSO enabled. Intel's commit 5e6038b88a ("net: stmmac: fix TSO and
TBS feature enabling during driver open") concurs with this, but it
is incomplete.
This commit avoids enabling TSO support on the channels which have
TBS available, which, as far as the hardware is concerned, means we
do not set the TSE bit in the DMA channel's transmit control register.
However, the net device's features apply to all queues(channels), which
means these channels may still be handed TSO skbs to transmit, and the
driver will pass them to stmmac_tso_xmit(). This will generate the
descriptors for TSO, even though the channel has the TSE bit clear.
Fix this by checking whether the queue(channel) has TBS available,
and if it does, fall back to software GSO support.
Fixes: 5e6038b88a ("net: stmmac: fix TSO and TBS feature enabling during driver open")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1w7ptE-0000000Easz-28tv@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
netdev features documentation requires that .ndo_fix_features() is
stateless: it shouldn't modify driver state. Yet, stmmac_fix_features()
does exactly that, changing whether GSO frames are processed by the
driver.
Move this code to stmmac_set_features() instead, which is the correct
place for it. We don't need to check whether TSO is supported; this
is already handled via the setup of netdev->hw_features, and we are
guaranteed that if netdev->hw_features indicates that a feature is
not supported, .ndo_set_features() won't be called with it set.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1w7pt9-0000000East-1YAO@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rather than configuring the channels depending on whether GSO/TSO is
currently enabled by the user, always enable if the hardware has TSO
support and the platform wants TSO to be enabled.
This avoids the channel TSO enable bit being disabled after a resume
when the user has disabled TSO features. This will cause problems when
the user re-enables TSO.
This bug goes back to commit f748be531d ("stmmac: support new GMAC4")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1w7pt4-0000000Easn-14WL@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking fixes from Jakub Kicinski:
"With fixes from wireless, bluetooth and netfilter included we're back
to each PR carrying 30%+ more fixes than in previous era.
The good news is that so far none of the "extra" fixes are themselves
causing real regressions. Not sure how much comfort that is.
Current release - fix to a fix:
- netdevsim: fix build if SKB_EXTENSIONS=n
- eth: stmmac: skip VLAN restore when VLAN hash ops are missing
Previous releases - regressions:
- wifi: iwlwifi: mvm: don't send a 6E related command when
not supported
Previous releases - always broken:
- some info leak fixes
- add missing clearing of skb->cb[] on ICMP paths from tunnels
- ipv6:
- flowlabel: defer exclusive option free until RCU teardown
- avoid overflows in ip6_datagram_send_ctl()
- mpls: add seqcount to protect platform_labels from OOB access
- bridge: improve safety of parsing ND options
- bluetooth: fix leaks, overflows and races in hci_sync
- netfilter: add more input validation, some to address bugs directly
some to prevent exploits from cooking up broken configurations
- wifi:
- ath: avoid poor performance due to stopping the wrong
aggregation session
- virt_wifi: remove SET_NETDEV_DEV to avoid use-after-free
- eth:
- fec: fix the PTP periodic output sysfs interface
- enetc: safely reinitialize TX BD ring when it has unsent frames"
* tag 'net-7.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (95 commits)
eth: fbnic: Increase FBNIC_QUEUE_SIZE_MIN to 64
ipv6: avoid overflows in ip6_datagram_send_ctl()
net: hsr: fix VLAN add unwind on slave errors
net: hsr: serialize seq_blocks merge across nodes
vsock: initialize child_ns_mode_locked in vsock_net_init()
selftests/tc-testing: add tests for cls_fw and cls_flow on shared blocks
net/sched: cls_flow: fix NULL pointer dereference on shared blocks
net/sched: cls_fw: fix NULL pointer dereference on shared blocks
net/x25: Fix overflow when accumulating packets
net/x25: Fix potential double free of skb
bnxt_en: Restore default stat ctxs for ULP when resource is available
bnxt_en: Don't assume XDP is never enabled in bnxt_init_dflt_ring_mode()
bnxt_en: Refactor some basic ring setup and adjustment logic
net/mlx5: Fix switchdev mode rollback in case of failure
net/mlx5: Avoid "No data available" when FW version queries fail
net/mlx5: lag: Check for LAG device before creating debugfs
net: macb: properly unregister fixed rate clocks
net: macb: fix clk handling on PCI glue driver removal
virtio_net: clamp rss_max_key_size to NETDEV_RSS_KEY_LEN
net/sched: sch_netem: fix out-of-bounds access in packet corruption
...
Pull iommu fixes from Joerg Roedel:
- IOMMU-PT related compile breakage in for AMD driver
- IOTLB flushing behavior when unmapped region is larger than requested
due to page-sizes
- Fix IOTLB flush behavior with empty gathers
* tag 'iommu-fixes-v7.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux:
iommupt/amdv1: mark amdv1pt_install_leaf_entry as __always_inline
iommupt: Fix short gather if the unmap goes into a large mapping
iommu: Do not call drivers for empty gathers
Pull sound fixes from Takashi Iwai:
"People have been so busy for hunting and we're still getting more
changes than wished for, but it doesn't look too scary; almost all
changes are device-specific small fixes.
I guess it's rather a casual bump, and no more Easter eggs are left
for 7.0 (hopefully)...
- Fixes for the recent regression on ctxfi driver
- Fix missing INIT_LIST_HEAD() for ASoC card_aux_list
- Usual HD- and USB-audio, and ASoC AMD quirk updates
- ASoC fixes for AMD and Intel"
* tag 'sound-7.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (24 commits)
ASoC: amd: ps: Fix missing leading zeros in subsystem_device SSID log
ALSA: usb-audio: Exclude Scarlett 2i2 1st Gen (8016) from SKIP_IFACE_SETUP
ALSA: hda/realtek: add quirk for Acer Swift SFG14-73
ALSA: hda/realtek: Add quirk for Lenovo Yoga Pro 7 14IMH9
ASoC: Intel: boards: fix unmet dependency on PINCTRL
ASoC: Intel: ehl_rt5660: Use the correct rtd->dev device in hw_params
ALSA: ctxfi: Don't enumerate SPDIF1 at DAIO initialization
ALSA: hda/realtek: Add quirk for Lenovo Yoga Slim 7 14AKP10
ALSA: hda/realtek: add quirk for HP Laptop 15-fc0xxx
ASoC: ep93xx: Fix unchecked clk_prepare_enable() and add rollback on failure
ASoC: soc-core: call missing INIT_LIST_HEAD() for card_aux_list
ALSA: hda/realtek: Add quirk for Samsung Book2 Pro 360 (NP950QED)
ASoC: amd: yc: Add DMI entry for HP Laptop 15-fc0xxx
ASoC: amd: yc: Add DMI quirk for ASUS Vivobook Pro 16X OLED M7601RM
ALSA: hda/realtek: Add quirk for ASUS ROG Strix SCAR 15
ALSA: usb-audio: Exclude Scarlett Solo 1st Gen from SKIP_IFACE_SETUP
ALSA: caiaq: fix stack out-of-bounds read in init_card
ALSA: ctxfi: Check the error for index mapping
ALSA: ctxfi: Fix missing SPDIFI1 index handling
ALSA: hda/realtek: add quirk for HP Victus 15-fb0xxx
...
Pull auxdisplay fixes from Andy Shevchenko:
- Fix NULL dereference in linedisp_release()
- Fix ht16k33 DT bindings to avoid warnings
- Handle errors in I²C transfers in lcd2s driver
* tag 'auxdisplay-v7.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-auxdisplay:
auxdisplay: line-display: fix NULL dereference in linedisp_release
auxdisplay: lcd2s: add error handling for i2c transfers
dt-bindings: auxdisplay: ht16k33: Use unevaluatedProperties to fix common property warning
On systems with 64K pages, RX queues will be wedged if users set the
descriptor count to the current minimum (16). Fbnic fragments large
pages into 4K chunks, and scales down the ring size accordingly. With
64K pages and 16 descriptors, the ring size mask is 0 and will never
be filled.
32 descriptors is another special case that wedges the RX rings.
Internally, the rings track pages for the head/tail pointers, not page
fragments. So with 32 descriptors, there's only 1 usable page as one
ring slot is kept empty to disambiguate between an empty/full ring.
As a result, the head pointer never advances and the HW stalls after
consuming 16 page fragments.
Fixes: 0cb4c0a137 ("eth: fbnic: Implement Rx queue alloc/start/stop/free")
Signed-off-by: Dimitri Daskalakis <daskald@meta.com>
Link: https://patch.msgid.link/20260401162848.2335350-1-dimitri.daskalakis1@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yiming Qian reported :
<quote>
I believe I found a locally triggerable kernel bug in the IPv6 sendmsg
ancillary-data path that can panic the kernel via `skb_under_panic()`
(local DoS).
The core issue is a mismatch between:
- a 16-bit length accumulator (`struct ipv6_txoptions::opt_flen`, type
`__u16`) and
- a pointer to the *last* provided destination-options header (`opt->dst1opt`)
when multiple `IPV6_DSTOPTS` control messages (cmsgs) are provided.
- `include/net/ipv6.h`:
- `struct ipv6_txoptions::opt_flen` is `__u16` (wrap possible).
(lines 291-307, especially 298)
- `net/ipv6/datagram.c:ip6_datagram_send_ctl()`:
- Accepts repeated `IPV6_DSTOPTS` and accumulates into `opt_flen`
without rejecting duplicates. (lines 909-933)
- `net/ipv6/ip6_output.c:__ip6_append_data()`:
- Uses `opt->opt_flen + opt->opt_nflen` to compute header
sizes/headroom decisions. (lines 1448-1466, especially 1463-1465)
- `net/ipv6/ip6_output.c:__ip6_make_skb()`:
- Calls `ipv6_push_frag_opts()` if `opt->opt_flen` is non-zero.
(lines 1930-1934)
- `net/ipv6/exthdrs.c:ipv6_push_frag_opts()` / `ipv6_push_exthdr()`:
- Push size comes from `ipv6_optlen(opt->dst1opt)` (based on the
pointed-to header). (lines 1179-1185 and 1206-1211)
1. `opt_flen` is a 16-bit accumulator:
- `include/net/ipv6.h:298` defines `__u16 opt_flen; /* after fragment hdr */`.
2. `ip6_datagram_send_ctl()` accepts *repeated* `IPV6_DSTOPTS` cmsgs
and increments `opt_flen` each time:
- In `net/ipv6/datagram.c:909-933`, for `IPV6_DSTOPTS`:
- It computes `len = ((hdr->hdrlen + 1) << 3);`
- It checks `CAP_NET_RAW` using `ns_capable(net->user_ns,
CAP_NET_RAW)`. (line 922)
- Then it does:
- `opt->opt_flen += len;` (line 927)
- `opt->dst1opt = hdr;` (line 928)
There is no duplicate rejection here (unlike the legacy
`IPV6_2292DSTOPTS` path which rejects duplicates at
`net/ipv6/datagram.c:901-904`).
If enough large `IPV6_DSTOPTS` cmsgs are provided, `opt_flen` wraps
while `dst1opt` still points to a large (2048-byte)
destination-options header.
In the attached PoC (`poc.c`):
- 32 cmsgs with `hdrlen=255` => `len = (255+1)*8 = 2048`
- 1 cmsg with `hdrlen=0` => `len = 8`
- Total increment: `32*2048 + 8 = 65544`, so `(__u16)opt_flen == 8`
- The last cmsg is 2048 bytes, so `dst1opt` points to a 2048-byte header.
3. The transmit path sizes headers using the wrapped `opt_flen`:
- In `net/ipv6/ip6_output.c:1463-1465`:
- `headersize = sizeof(struct ipv6hdr) + (opt ? opt->opt_flen +
opt->opt_nflen : 0) + ...;`
With wrapped `opt_flen`, `headersize`/headroom decisions underestimate
what will be pushed later.
4. When building the final skb, the actual push length comes from
`dst1opt` and is not limited by wrapped `opt_flen`:
- In `net/ipv6/ip6_output.c:1930-1934`:
- `if (opt->opt_flen) proto = ipv6_push_frag_opts(skb, opt, proto);`
- In `net/ipv6/exthdrs.c:1206-1211`, `ipv6_push_frag_opts()` pushes
`dst1opt` via `ipv6_push_exthdr()`.
- In `net/ipv6/exthdrs.c:1179-1184`, `ipv6_push_exthdr()` does:
- `skb_push(skb, ipv6_optlen(opt));`
- `memcpy(h, opt, ipv6_optlen(opt));`
With insufficient headroom, `skb_push()` underflows and triggers
`skb_under_panic()` -> `BUG()`:
- `net/core/skbuff.c:2669-2675` (`skb_push()` calls `skb_under_panic()`)
- `net/core/skbuff.c:207-214` (`skb_panic()` ends in `BUG()`)
- The `IPV6_DSTOPTS` cmsg path requires `CAP_NET_RAW` in the target
netns user namespace (`ns_capable(net->user_ns, CAP_NET_RAW)`).
- Root (or any task with `CAP_NET_RAW`) can trigger this without user
namespaces.
- An unprivileged `uid=1000` user can trigger this if unprivileged
user namespaces are enabled and it can create a userns+netns to obtain
namespaced `CAP_NET_RAW` (the attached PoC does this).
- Local denial of service: kernel BUG/panic (system crash).
- Reproducible with a small userspace PoC.
</quote>
This patch does not reject duplicated options, as this might break
some user applications.
Instead, it makes sure to adjust opt_flen and opt_nflen to correctly
reflect the size of the current option headers, preventing the overflows
and the potential for panics.
This applies to IPV6_DSTOPTS, IPV6_HOPOPTS, and IPV6_RTHDR.
Specifically:
When a new IPV6_DSTOPTS is processed, the length of the old opt->dst1opt
is subtracted from opt->opt_flen before adding the new length.
When a new IPV6_HOPOPTS is processed, the length of the old opt->dst0opt
is subtracted from opt->opt_nflen.
When a new Routing Header (IPV6_RTHDR or IPV6_2292RTHDR) is processed,
the length of the old opt->srcrt is subtracted from opt->opt_nflen.
In the special case within IPV6_2292RTHDR handling where dst1opt is moved
to dst0opt, the length of the old opt->dst0opt is subtracted from
opt->opt_nflen before the new one is added.
Fixes: 333fad5364 ("[IPV6]: Support several new sockopt / ancillary data in Advanced API (RFC3542).")
Reported-by: Yiming Qian <yimingqian591@gmail.com>
Closes: https://lore.kernel.org/netdev/CAL_bE8JNzawgr5OX5m+3jnQDHry2XxhQT5=jThW1zDPtUikRYA@mail.gmail.com/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260401154721.3740056-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Luka Gejak says:
====================
net: hsr: fixes for PRP duplication and VLAN unwind
This series addresses two logic bugs in the HSR/PRP implementation
identified during a protocol audit. These are targeted for the 'net'
tree as they fix potential memory corruption and state inconsistency.
The primary change resolves a race condition in the node merging path by
implementing address-based lock ordering. This ensures that concurrent
mutations of sequence blocks do not lead to state corruption or
deadlocks.
An additional fix corrects asymmetric VLAN error unwinding by
implementing a centralized unwind path on slave errors.
====================
Link: https://patch.msgid.link/20260401092243.52121-1-luka.gejak@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When vlan_vid_add() fails for a secondary slave, the error path calls
vlan_vid_del() on the failing port instead of the peer slave that had
already succeeded. This results in asymmetric VLAN state across the HSR
pair.
Fix this by switching to a centralized unwind path that removes the VID
from any slave device that was already programmed.
Fixes: 1a8a63a530 ("net: hsr: Add VLAN CTAG filter support")
Signed-off-by: Luka Gejak <luka.gejak@linux.dev>
Link: https://patch.msgid.link/20260401092243.52121-3-luka.gejak@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During node merging, hsr_handle_sup_frame() walks node_curr->seq_blocks
to update node_real without holding node_curr->seq_out_lock. This
allows concurrent mutations from duplicate registration paths, risking
inconsistent state or XArray/bitmap corruption.
Fix this by locking both nodes' seq_out_lock during the merge.
To prevent ABBA deadlocks, locks are acquired in order of memory
address.
Reviewed-by: Felix Maurer <fmaurer@redhat.com>
Fixes: 415e636751 ("hsr: Implement more robust duplicate discard for PRP")
Signed-off-by: Luka Gejak <luka.gejak@linux.dev>
Link: https://patch.msgid.link/20260401092243.52121-2-luka.gejak@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The `child_ns_mode_locked` field lives in `struct net`, which persists
across vsock module reloads. When the module is unloaded and reloaded,
`vsock_net_init()` resets `mode` and `child_ns_mode` back to their
default values, but does not reset `child_ns_mode_locked`.
The stale lock from the previous module load causes subsequent writes
to `child_ns_mode` to silently fail: `vsock_net_set_child_mode()` sees
the old lock, skips updating the actual value, and returns success
when the requested mode matches the stale lock. The sysctl handler
reports no error, but `child_ns_mode` remains unchanged.
Steps to reproduce:
$ modprobe vsock
$ echo local > /proc/sys/net/vsock/child_ns_mode
$ cat /proc/sys/net/vsock/child_ns_mode
local
$ modprobe -r vsock
$ modprobe vsock
$ echo local > /proc/sys/net/vsock/child_ns_mode
$ cat /proc/sys/net/vsock/child_ns_mode
global <--- expected "local"
Fix this by initializing `child_ns_mode_locked` to 0 (unlocked) in
`vsock_net_init()`, so the write-once mechanism works correctly after
module reload.
Fixes: 102eab95f0 ("vsock: lock down child_ns_mode as write-once")
Reported-by: Jin Liu <jinl@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Bobby Eshleman <bobbyeshleman@meta.com>
Link: https://patch.msgid.link/20260401092153.28462-1-sgarzare@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Regression tests for the shared-block NULL derefs fixed in the previous
two patches:
- fw: attempt to attach an empty fw filter to a shared block and
verify the configuration is rejected with EINVAL.
- flow: create a flow filter on a shared block without a baseclass
and verify the configuration is rejected with EINVAL.
Signed-off-by: Xiang Mei <xmei5@asu.edu>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Victor Nogueira <victor@mojatatu.com>
Link: https://patch.msgid.link/20260331050217.504278-3-xmei5@asu.edu
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
flow_change() calls tcf_block_q() and dereferences q->handle to derive
a default baseclass. Shared blocks leave block->q NULL, causing a NULL
deref when a flow filter without a fully qualified baseclass is created
on a shared block.
Check tcf_block_shared() before accessing block->q and return -EINVAL
for shared blocks. This avoids the null-deref shown below:
=======================================================================
KASAN: null-ptr-deref in range [0x0000000000000038-0x000000000000003f]
RIP: 0010:flow_change (net/sched/cls_flow.c:508)
Call Trace:
tc_new_tfilter (net/sched/cls_api.c:2432)
rtnetlink_rcv_msg (net/core/rtnetlink.c:6980)
[...]
=======================================================================
Fixes: 1abf272022 ("net: sched: tcindex, fw, flow: use tcf_block_q helper to get struct Qdisc")
Reported-by: Weiming Shi <bestswngs@gmail.com>
Signed-off-by: Xiang Mei <xmei5@asu.edu>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://patch.msgid.link/20260331050217.504278-2-xmei5@asu.edu
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The old-method path in fw_classify() calls tcf_block_q() and
dereferences q->handle. Shared blocks leave block->q NULL, causing a
NULL deref when an empty cls_fw filter is attached to a shared block
and a packet with a nonzero major skb mark is classified.
Reject the configuration in fw_change() when the old method (no
TCA_OPTIONS) is used on a shared block, since fw_classify()'s
old-method path needs block->q which is NULL for shared blocks.
The fixed null-ptr-deref calling stack:
KASAN: null-ptr-deref in range [0x0000000000000038-0x000000000000003f]
RIP: 0010:fw_classify (net/sched/cls_fw.c:81)
Call Trace:
tcf_classify (./include/net/tc_wrapper.h:197 net/sched/cls_api.c:1764 net/sched/cls_api.c:1860)
tc_run (net/core/dev.c:4401)
__dev_queue_xmit (net/core/dev.c:4535 net/core/dev.c:4790)
Fixes: 1abf272022 ("net: sched: tcindex, fw, flow: use tcf_block_q helper to get struct Qdisc")
Reported-by: Weiming Shi <bestswngs@gmail.com>
Signed-off-by: Xiang Mei <xmei5@asu.edu>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://patch.msgid.link/20260331050217.504278-1-xmei5@asu.edu
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Martin Schiller says:
====================
net/x25: Fix overflow and double free
This patch set includes 2 fixes:
The first removes a potential double free of received skb
The second fixes an overflow when accumulating packets with the more-bit
set.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
====================
Link: https://patch.msgid.link/20260331-x25_fraglen-v4-0-3e69f18464b4@dev.tdt.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When alloc_skb fails in x25_queue_rx_frame it calls kfree_skb(skb) at
line 48 and returns 1 (error).
This error propagates back through the call chain:
x25_queue_rx_frame returns 1
|
v
x25_state3_machine receives the return value 1 and takes the else
branch at line 278, setting queued=0 and returning 0
|
v
x25_process_rx_frame returns queued=0
|
v
x25_backlog_rcv at line 452 sees queued=0 and calls kfree_skb(skb)
again
This would free the same skb twice. Looking at x25_backlog_rcv:
net/x25/x25_in.c:x25_backlog_rcv() {
...
queued = x25_process_rx_frame(sk, skb);
...
if (!queued)
kfree_skb(skb);
}
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://patch.msgid.link/20260331-x25_fraglen-v4-1-3e69f18464b4@dev.tdt.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jeremy Kerr says:
====================
net: mctp: improvements for NULL-EID addressing
Currently, our focus for the MCTP routing implementation has been for
MCTP bus-owner devices. In this case, we will generally have an EID
assigned during local transmit, and have routes established before
expecting to receive.
We also want to handle non-bus-owner cases, where:
- we may need to send control protocol messages (like Discovery Notify)
before any local addresses have been assigned, particularly as part
of acquiring a local address assignment; and
- we will likely want to receive incoming messages before we have
routing established.
This series improves handling for these cases, by handling NULL EIDs
as source / destination addresses where possible.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
====================
Link: https://patch.msgid.link/20260331-dev-mctp-null-eids-v1-0-b4d047372eaf@codeconstruct.com.au
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently, if we receive a physically-addressed packet for the local
stack, we perform a route_lookup_null to find a matching device-based
route. If a route is present, it will always have the ->output fn set to
mctp_dst_input, which provides our delivery mechanism.
However, if we don't yet have any local addresses assigned, we won't
have any local routes to lookup, so this will fail. One of the use-cases
for physical addressing is initial address assignment on endpoint nodes,
where we would have no addresses, and therefore no local routes.
Instead of iterating routes (looking for one matching the dev), just
create a suitable mctp_dst for the device directly.
Add a testcase for the no-route case too.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://patch.msgid.link/20260331-dev-mctp-null-eids-v1-3-b4d047372eaf@codeconstruct.com.au
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Rather than querying the output device for its address in
mctp_local_output, set up the source address when we're populating the
dst structure. If no address is assigned, use MCTP_ADDR_NULL.
This will allow us more flexibility when routing for NULL-source-eid
cases. For now though, we still reject a NULL source address in the
output path.
We need to update the tests a little, so that addresses are assigned
before we do the dst lookups.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://patch.msgid.link/20260331-dev-mctp-null-eids-v1-1-b4d047372eaf@codeconstruct.com.au
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Ioana Ciornei says:
====================
selftests: drivers: bash support for remote traffic generators
This patch set aims to add the necessary support so that bash written
selftests are also able to easily run with a remote traffic generator
system, either be it in another netns or one accessible through ssh.
This patch set is a result of the discussion from v1:
https://lore.kernel.org/all/20260303084330.340b6459@kernel.org/
Even though the python infrastructure is already established, some
things are easier in bash and it would be a shame to leave behind the
bash tests that we already have.
This support is based on the requirements described in the
tools/testing/selftests/drivers/net/README.rst file.
Mainly, the drivers/net selftests should be able to run on a interface
specified through the NETIF env variable. On top of that, variables such
as REMOTE_TYPE and REMOTE_ARGS define how the remote traffic generator
can be accessed. Patch 3/10 parses these env variables and constructs the
NETIFS array that bash tests are accustomed to. This is with the
intention of enabling already written tests to incur minimal changes.
The second patch also defines the TARGETS array which will hold the
necessary information about the target on which a specific interface
is located.
For example, a net.config which looks like below:
NETIF=eth0
LOCAL_V4=192.168.1.1
REMOTE_V4=192.168.1.2
REMOTE_TYPE=ssh
REMOTE_ARGS=root@192.168.1.2
will generate the NETIFS and TARGETS arrays with the following data.
NETIFS[p1]="eth0"
NETIFS[p2]="eth2"
TARGETS[eth0]="local:"
TARGETS[eth2]="ssh:root@192.168.1.2"
The above will be true if on the remote target, the interface which has
the 192.168.1.2 address is named eth2.
The values held in the TARGETS array will be used by the new 'run_on'
helper added in patch 2/10 to know how to run a specific command, on the
local system, on another netns or by using ssh. Patch 4/10 updates some
helpers to use run_on so that, for example, lib.sh is able to ensure
stable MAC addresses even with the remote interface located in another
netns.
The next 5 patches, 5/10-9/10 update the ethtool_rmon.sh script so that it
can work with the kselftest infrastructure and the new
NETIF/REMOTE_TYPE etc way of working. Beside updating each ip link or
ethtool command to use the run_on helper, the patches also remove any
testing done on the remote interface.
The last patch adds a new test which checks the standard counters -
eth-ctrl, eth-mac and pause - and uses the new infrastructure put in
place by the first patches.
With this patch set, both tests can be run using a net.config file and
run_kselftest.sh as shown below.
$ make -C tools/testing/selftests/ TARGETS="drivers/net drivers/net/hw" \
install INSTALL_PATH=/tmp/ksft-net-drv
$ cd /tmp/ksft-net-drv/
$ cat > ./drivers/net/net.config <<EOF
NETIF=endpmac17
LOCAL_V4=17.0.0.1
REMOTE_V4=17.0.0.2
REMOTE_TYPE=ssh
REMOTE_ARGS=root@192.168.5.200
EOF
$ ./run_kselftest.sh -t drivers/net/hw:ethtool_rmon.sh
TAP version 13
1..1
# timeout set to 0
# selftests: drivers/net/hw: ethtool_rmon.sh
# TAP version 13
# 1..14
# ok 1 ethtool_rmon.rx-pkts64to64
# ok 2 ethtool_rmon.rx-pkts65to127
# ok 3 ethtool_rmon.rx-pkts128to255
# ok 4 ethtool_rmon.rx-pkts256to511
# ok 5 ethtool_rmon.rx-pkts512to1023
# ok 6 ethtool_rmon.rx-pkts1024to1518
# ok 7 ethtool_rmon.rx-pkts1519to10240
# ok 8 ethtool_rmon.tx-pkts64to64
# ok 9 ethtool_rmon.tx-pkts65to127
# ok 10 ethtool_rmon.tx-pkts128to255
# ok 11 ethtool_rmon.tx-pkts256to511
# ok 12 ethtool_rmon.tx-pkts512to1023
# ok 13 ethtool_rmon.tx-pkts1024to1518
# ok 14 ethtool_rmon.tx-pkts1519to10240
# # Totals: pass:14 fail:0 xfail:0 xpass:0 skip:0 error:0
ok 1 selftests: drivers/net/hw: ethtool_rmon.sh
$ ./run_kselftest.sh -t drivers/net/hw:ethtool_std_stats.sh
TAP version 13
1..1
# timeout set to 0
# selftests: drivers/net/hw: ethtool_std_stats.sh
# TAP version 13
# 1..26
# ok 1 ethtool_std_stats.eth-ctrl-MACControlFramesTransmitted
# ok 2 ethtool_std_stats.eth-ctrl-MACControlFramesReceived
# ok 3 ethtool_std_stats.eth-mac-FrameCheckSequenceErrors
# ok 4 ethtool_std_stats.eth-mac-AlignmentErrors
# ok 5 ethtool_std_stats.eth-mac-FramesLostDueToIntMACXmitError
# ok 6 ethtool_std_stats.eth-mac-CarrierSenseErrors # SKIP
# ok 7 ethtool_std_stats.eth-mac-FramesLostDueToIntMACRcvError
# ok 8 ethtool_std_stats.eth-mac-InRangeLengthErrors # SKIP
# ok 9 ethtool_std_stats.eth-mac-OutOfRangeLengthField # SKIP
# ok 10 ethtool_std_stats.eth-mac-FrameTooLongErrors # SKIP
# ok 11 ethtool_std_stats.eth-mac-FramesAbortedDueToXSColls # SKIP
# ok 12 ethtool_std_stats.eth-mac-SingleCollisionFrames # SKIP
# ok 13 ethtool_std_stats.eth-mac-MultipleCollisionFrames # SKIP
# ok 14 ethtool_std_stats.eth-mac-FramesWithDeferredXmissions # SKIP
# ok 15 ethtool_std_stats.eth-mac-LateCollisions # SKIP
# ok 16 ethtool_std_stats.eth-mac-FramesWithExcessiveDeferral # SKIP
# ok 17 ethtool_std_stats.eth-mac-BroadcastFramesXmittedOK
# ok 18 ethtool_std_stats.eth-mac-OctetsTransmittedOK
# ok 19 ethtool_std_stats.eth-mac-BroadcastFramesReceivedOK
# ok 20 ethtool_std_stats.eth-mac-OctetsReceivedOK
# ok 21 ethtool_std_stats.eth-mac-FramesTransmittedOK
# ok 22 ethtool_std_stats.eth-mac-MulticastFramesXmittedOK
# ok 23 ethtool_std_stats.eth-mac-FramesReceivedOK
# ok 24 ethtool_std_stats.eth-mac-MulticastFramesReceivedOK
# ok 25 ethtool_std_stats.pause-tx_pause_frames
# ok 26 ethtool_std_stats.pause-rx_pause_frames
# # 10 skipped test(s) detected. Consider enabling relevant config options to improve coverage.
# # Totals: pass:16 fail:0 xfail:0 xpass:0 skip:10 error:0
ok 1 selftests: drivers/net/hw: ethtool_std_stats.sh
====================
Link: https://patch.msgid.link/20260330152933.2195885-1-ioana.ciornei@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add a new selftest - ethtool_std_stats.sh - which validates the
eth-ctrl, eth-mac and pause standard statistics exported by an
interface. Collision related eth-mac counters as well as the error ones
will be checked against zero since that is the most likely correct
scenario.
The central part of this patch is the traffic_test() function which
gathers the 'before' counter values, sends a batch of traffic and then
interrogates again the same counters in order to determine if the delta
is on target. The function receives an array through which the caller
can request what counters to be interrogated and, for each of them, what
is their target delta value.
The output from this selftest looks as follows on a LX2160ARDB board:
$ ./run_kselftest.sh -t drivers/net/hw:ethtool_std_stats.sh
TAP version 13
1..1
# timeout set to 0
# selftests: drivers/net/hw: ethtool_std_stats.sh
# TAP version 13
# 1..26
# ok 1 ethtool_std_stats.eth-ctrl-MACControlFramesTransmitted
# ok 2 ethtool_std_stats.eth-ctrl-MACControlFramesReceived
# ok 3 ethtool_std_stats.eth-mac-FrameCheckSequenceErrors
# ok 4 ethtool_std_stats.eth-mac-AlignmentErrors
# ok 5 ethtool_std_stats.eth-mac-FramesLostDueToIntMACXmitError
# ok 6 ethtool_std_stats.eth-mac-CarrierSenseErrors # SKIP
# ok 7 ethtool_std_stats.eth-mac-FramesLostDueToIntMACRcvError
# ok 8 ethtool_std_stats.eth-mac-InRangeLengthErrors # SKIP
# ok 9 ethtool_std_stats.eth-mac-OutOfRangeLengthField # SKIP
# ok 10 ethtool_std_stats.eth-mac-FrameTooLongErrors # SKIP
# ok 11 ethtool_std_stats.eth-mac-FramesAbortedDueToXSColls # SKIP
# ok 12 ethtool_std_stats.eth-mac-SingleCollisionFrames # SKIP
# ok 13 ethtool_std_stats.eth-mac-MultipleCollisionFrames # SKIP
# ok 14 ethtool_std_stats.eth-mac-FramesWithDeferredXmissions # SKIP
# ok 15 ethtool_std_stats.eth-mac-LateCollisions # SKIP
# ok 16 ethtool_std_stats.eth-mac-FramesWithExcessiveDeferral # SKIP
# ok 17 ethtool_std_stats.eth-mac-BroadcastFramesXmittedOK
# ok 18 ethtool_std_stats.eth-mac-OctetsTransmittedOK
# ok 19 ethtool_std_stats.eth-mac-BroadcastFramesReceivedOK
# ok 20 ethtool_std_stats.eth-mac-OctetsReceivedOK
# ok 21 ethtool_std_stats.eth-mac-FramesTransmittedOK
# ok 22 ethtool_std_stats.eth-mac-MulticastFramesXmittedOK
# ok 23 ethtool_std_stats.eth-mac-FramesReceivedOK
# ok 24 ethtool_std_stats.eth-mac-MulticastFramesReceivedOK
# ok 25 ethtool_std_stats.pause-tx_pause_frames
# ok 26 ethtool_std_stats.pause-rx_pause_frames
# # 10 skipped test(s) detected. Consider enabling relevant config options to improve coverage.
# # Totals: pass:16 fail:0 xfail:0 xpass:0 skip:10 error:0
ok 1 selftests: drivers/net/hw: ethtool_std_stats.sh
Please note that not all MACs are counting the software injected pause
frames as real Tx pause. For example, on a LS1028ARDB the selftest
output will reflect the fact that neither the ENETC MAC, nor the Felix
switch MAC are able to detect Tx pause frames injected by software.
$ ./run_kselftest.sh -t drivers/net/hw:ethtool_std_stats.sh
(...)
# # software sent pause frames not detected
# ok 25 ethtool_std_stats.pause-tx_pause_frames # XFAIL
# ok 26 ethtool_std_stats.pause-rx_pause_frames
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Petr Machata <petrm@nvidia.com>
Link: https://patch.msgid.link/20260330152933.2195885-10-ioana.ciornei@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch finalizes the transition to work with a single local
interface for the ethtool_rmon.sh test. Each 'ip link' and 'ethtool'
command used by the test is annotated with the necessary run_on in
order to be executed on the necessary target system, be it local, in
another network namespace or through ssh.
Since we need NETIF up and running also for control traffic, we now
expect that the interfaces are up and running and do not touch bring
them up or down at the end of the test. This is also documented in the
drivers/net/README.rst.
The ethtool_rmon.sh script can still be used in the older fashion by
passing two interfaces as command line arguments, the only restriction
is that those interfaces need to be already up.
$ DRIVER_TEST_CONFORMANT=no ./ethtool_rmon.sh eth0 eth1
As part of the kselftest infrastructure, this test can be run in the
following manner:
$ make -C tools/testing/selftests/ TARGETS="drivers/net drivers/net/hw" \
install INSTALL_PATH=/tmp/ksft-net-drv
$ cd /tmp/ksft-net-drv/
$ cat > ./drivers/net/net.config <<EOF
NETIF=endpmac17
LOCAL_V4=17.0.0.1
REMOTE_V4=17.0.0.2
REMOTE_TYPE=ssh
REMOTE_ARGS=root@192.168.5.200
EOF
$ ./run_kselftest.sh -t drivers/net/hw:ethtool_rmon.sh
TAP version 13
1..1
# timeout set to 0
# selftests: drivers/net/hw: ethtool_rmon.sh
# TAP version 13
# 1..14
# ok 1 ethtool_rmon.rx-pkts64to64
# ok 2 ethtool_rmon.rx-pkts65to127
# ok 3 ethtool_rmon.rx-pkts128to255
# ok 4 ethtool_rmon.rx-pkts256to511
# ok 5 ethtool_rmon.rx-pkts512to1023
# ok 6 ethtool_rmon.rx-pkts1024to1518
# ok 7 ethtool_rmon.rx-pkts1519to10240
# ok 8 ethtool_rmon.tx-pkts64to64
# ok 9 ethtool_rmon.tx-pkts65to127
# ok 10 ethtool_rmon.tx-pkts128to255
# ok 11 ethtool_rmon.tx-pkts256to511
# ok 12 ethtool_rmon.tx-pkts512to1023
# ok 13 ethtool_rmon.tx-pkts1024to1518
# ok 14 ethtool_rmon.tx-pkts1519to10240
# # Totals: pass:14 fail:0 xfail:0 xpass:0 skip:0 error:0
ok 1 selftests: drivers/net/hw: ethtool_rmon.sh
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://patch.msgid.link/20260330152933.2195885-9-ioana.ciornei@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Update the ethtool_rmon.sh test so that it uses the KTAP format for its
output. This is achieved by using the helpers found in ktap_helpers.sh.
An example output can be found below.
$ ./ethtool_rmon.sh endpmac3 endpmac4
TAP version 13
1..14
ok 1 ethtool_rmon.rx-pkts64to64
ok 2 ethtool_rmon.rx-pkts65to127
ok 3 ethtool_rmon.rx-pkts128to255
ok 4 ethtool_rmon.rx-pkts256to511
ok 5 ethtool_rmon.rx-pkts512to1023
ok 6 ethtool_rmon.rx-pkts1024to1518
ok 7 ethtool_rmon.rx-pkts1519to10240
ok 8 ethtool_rmon.tx-pkts64to64
ok 9 ethtool_rmon.tx-pkts65to127
ok 10 ethtool_rmon.tx-pkts128to255
ok 11 ethtool_rmon.tx-pkts256to511
ok 12 ethtool_rmon.tx-pkts512to1023
ok 13 ethtool_rmon.tx-pkts1024to1518
ok 14 ethtool_rmon.tx-pkts1519to10240
# Totals: pass:14 fail:0 xfail:0 xpass:0 skip:0 error:0
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://patch.msgid.link/20260330152933.2195885-8-ioana.ciornei@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The ethtool_rmon.sh script checks that the number of packets sent /
received during a test matches the expected value with a 1% tolerance.
Since in the next patches this test will gain the capability to also be
run on systems with a single interface where the traffic generator is
accesible through ssh, use the UINT32_MAX as the upper limit. This is
necessary since the same interface will be used also for control traffic
(the ssh commands) as well as the mausezahn generated one.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://patch.msgid.link/20260330152933.2195885-7-ioana.ciornei@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The selftests in drivers/net are slowly transitioning to being able to
be used on systems with a single network interface. The first step for the
ethtool_rmon.sh test is to only validate that the rmon counters are
properly exported on the first interface supplied as an argument.
Remove the rmon_histogram calls which intend to test also the rmon
counters on the 2nd interface. This also removes the need for the remote
system, which should be used only to inject traffic, to also support
rmon counters.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://patch.msgid.link/20260330152933.2195885-6-ioana.ciornei@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Update some helpers so that they are capable to run commands on
different targets than the local one. This patch makes the necesasy
modification for those helpers / sections of code which are needed for
the ethtool_rmon.sh test that will be converted in the next patches.
For example, mac_addr_prepare() and mac_addr_restore() used when
STABLE_MAC_ADDRS=yes need to ensure stable MAC addresses on interfaces
located even in other namespaces. In order to do that, append the 'ip
link' commands with a 'run_on $dev' tag.
The same run_on is necessary also when verifying if all the interfaces
listed in NETIFS are indeed available.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://patch.msgid.link/20260330152933.2195885-4-ioana.ciornei@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Extend lib.sh so that it's able to parse driver/net/net.config and
environment variables such as NETIF, REMOTE_TYPE, LOCAL_V4 etc described
in drivers/net/README.rst.
In order to make the transition towards running with a single local
interface smoother for the bash networking driver tests, beside sourcing
the net.config file also translate the new env variables into the old
style based on the NETIFS array. Since the NETIFS array only holds the
network interface names, also add a new array - TARGETS - which keeps
track of the target on which a specific interfaces resides - local,
netns or accesible through an ssh command.
For example, a net.config which looks like below:
NETIF=eth0
LOCAL_V4=192.168.1.1
REMOTE_V4=192.168.1.2
REMOTE_TYPE=ssh
REMOTE_ARGS=root@192.168.1.2
will generate the NETIFS and TARGETS arrays with the following data.
NETIFS[p1]="eth0"
NETIFS[p2]="eth2"
TARGETS[eth0]="local:"
TARGETS[eth2]="ssh:root@192.168.1.2"
The above will be true if on the remote target, the interface which has
the 192.168.1.2 address is named eth2.
Since the TARGETS array is indexed by the network interface name,
document a new restriction README.rst which states that the remote
interface cannot have the same name as the local one. Keep the old way
of populating the NETIFS variable based on the command line arguments.
This will be invoked in case DRIVER_TEST_CONFORMANT = "no".
Also add a couple of helpers which can be used by tests which need to
run a specific bash command on a different target than the local system,
be it either another netns or a remote system accessible through ssh.
The __run_on() function is passed through $1 the target on which the
command should be executed while run_on() is passed the name of the
interface that is then used to retrieve the target from the TARGETS
array.
Also add a stub run_on() function in net/lib.sh so that users of the
net/lib.sh are going through the stub only since neither NETIFS nor
TARGETS are valid in that circumstance.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://patch.msgid.link/20260330152933.2195885-3-ioana.ciornei@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Even though pause frame statistics are not exported through the same
ethtool command, there is no point in adding another helper just for
them. Extent the ethtool_std_stats_get() function so that we are able to
interrogate using the same helper all the standard statistics.
And since we are touching the function, convert the initial ethtool call
as well to the jq --arg form in order to be easier to read.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://patch.msgid.link/20260330152933.2195885-2-ioana.ciornei@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ASoC: Fixes for v7.0
Another smallish batch of fixes and quirks, these days it's AMD that is
getting all the DMI entries added. We've got one core fix for a missing
list initialisation with auxiliary devices, otherwise it's all fairly
small things.
Michael Chan says:
====================
bnxt_en: Bug fixes
The first patch is a refactor patch needed by the second patch to
fix XDP ring initialization during FW reset. The third patch
fixes an issue related to stats context reservation for RoCE.
====================
Link: https://patch.msgid.link/20260331065138.948205-1-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During resource reservation, if the L2 driver does not have enough
MSIX vectors to provide to the RoCE driver, it sets the stat ctxs for
ULP also to 0 so that we don't have to reserve it unnecessarily.
However, subsequently the user may reduce L2 rings thereby freeing up
some resources that the L2 driver can now earmark for RoCE. In this
case, the driver should restore the default ULP stat ctxs to make
sure that all RoCE resources are ready for use.
The RoCE driver may fail to initialize in this scenario without this
fix.
Fixes: d630624ebd ("bnxt_en: Utilize ulp client resources if RoCE is not registered")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20260331065138.948205-4-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The original code made the assumption that when we set up the initial
default ring mode, we must be just loading the driver and XDP cannot
be enabled yet. This is not true when the FW goes through a resource
or capability change. Resource reservations will be cancelled and
reinitialized with XDP already enabled. devlink reload with XDP enabled
will also have the same issue. This scenario will cause the ring
arithmetic to be all wrong in the bnxt_init_dflt_ring_mode() path
causing failure:
bnxt_en 0000:a1:00.0 ens2f0np0: bnxt_setup_int_mode err: ffffffea
bnxt_en 0000:a1:00.0 ens2f0np0: bnxt_request_irq err: ffffffea
bnxt_en 0000:a1:00.0 ens2f0np0: nic open fail (rc: ffffffea)
Fix it by properly accounting for XDP in the bnxt_init_dflt_ring_mode()
path by using the refactored helper functions in the previous patch.
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Fixes: ec5d31e3c1 ("bnxt_en: Handle firmware reset status during IF_UP.")
Fixes: 228ea8c187 ("bnxt_en: implement devlink dev reload driver_reinit")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20260331065138.948205-3-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King (Oracle)
Jakub Kicinski
Linus Torvalds
Dimitri Daskalakis
Eric Dumazet
Luka Gejak
Stefano Garzarella
Lorenzo Bianconi
Xiang Mei
Paolo Abeni
Martin Schiller
Jeremy Kerr
Ioana Ciornei
Takashi Iwai
Conor Dooley
Pavan Chebbi
Michael Chan